Blodgett KTT-10E Installation Manual
KTT-E Series
ELECTRIC TABLE TOP TILTING KETTLE
INSTALLATION – OPERATION – MAINTENANCE
BLODGETT OVEN COMPANY
www.blodgett.com
44 Lakeside Avenue, Burlington, Vermont 05401 USA Telephone: (802) 658-6600 Fax: (802) 864-0183
S00063 Rev B (7/11)
1
This is the safety alert symbol. It is used to alert you to potential
personal injury hazards. Obey all safety messages that follow this
symbol to avoid possible injury or death.
WARNING: Improper installation, operation, adjustment, alteration,
service or maintenance can cause property damage, injury or death.
Read the installation, operating and maintenance instructions
thoroughly before installing, operating or servicing this equipment.
This manual should be retained for future reference.
ADEQUATE CLEARANCES MUST BE MAINTAINED FOR SERVICING AND
PROPER OPERATION.
DO NOT ATTEMPT TO OPERATE THIS UNIT IN THE EVENT OF A POWER
FAILURE.
NOTICE: Contact the factory, the factory representative or local service
company to perform maintenance and repairs.
Intended for commercial use only. Not for household use.
IMPORTANT NOTES FOR INSTALLATION AND OPERATION
It is recommended that this manual be read thoroughly and that all instructions be followed
carefully.
2
TABLE OF CONTENTS
DESCRIPTION PAGE
IMPORTANT NOTES FOR INSTALLATION AND OPERATION ........................................ 2
SERVICE CONNECTIONS ................................................................................................. 4
1.0 INSTALLATION INSTRUCTIONS ................................................................................ 5
2.0 INTRODUCTION .......................................................................................................... 7
3.0 OPERATION INSTRUCTIONS .................................................................................... 8
4.0 CLEANING INSTRUCTIONS ..................................................................................... 10
5.0 TROUBLESHOOTING ............................................................................................... 11
APPENDIX A Material Safety Data Sheet ........................................................................... 12
3
F
E
SAFETY RELIEF VALVE
4 [102]
10 [254]
12.5 [318]
H J
1.25 [32]
L
K
G
14.50 [368]
A ID
B
C
D
4X WELD NUTS
5/16-18UNC
18 [457]
2.25 [57]
DIMENSIONS ARE IN INCHES [MM]
ELECTRICAL CONNECTION TO BE AS SPECIFIED ON DATA PLATE
6 gallons
CAPACITY
10 gallons
12 gallons
MODEL
KTT-10E
KTT-12E
KTT-6E
26
610
24
711
28
660
UNITS
45 litres
23 litres
38 litres
mm
mm
mm
CA B
432
381
365
14.38
305
406
16
12
17
15
DIMENSIONS
D
937
36.88
34.88
851
33.5
886
FE
17.25
15.25
387
438
26.25
22.25
565
667
H
28
686
27
30
762
711
G
114
4.50
KJ
108
6.12
156
4.25
14.75
314
12.38
375
117
4.62
105
4.12
10
254
L
324
12.75
12.75
324
inches
inches
inches
ELECTRICAL CHARACTERISTICS
PHASE
1
KTT-10E & KTT-12E
KTT-6E
1
3
3
MODEL
208V
36.0
57.6
33.3
20.8
34.1
54.6
31.5
19.7
220V 415V
AMPS PER LINE
31.3
18.1
28.9
50.0
240V
18.3
11.4
380V 480V
14.516.7
10.4 9.0
12.0
7.5
kW
N/A
N/A
N/A
N/A
N/A
N/A
SERVICE CONNECTIONS
4
WARNING: Electrical and grounding connections must comply with
the applicable portions of the National Electrical Code and/or other
local electrical codes.
1.0 INSTALLATION INSTRUCTIONS
Immediately after unpacking, check for possible shipping damage. If the kettle is found to be
damaged, save the packaging materials and contact the carrier within 15 days of delivery.
1. The kettle must be installed in accordance with:
2. State and/or local codes.
3. In the USA, the National Electrical Code, ANSI/NFPA-70 (latest edition). In Canada, the
Canadian Electrical Code, Part 1, CSA Standard C22.1 (latest edition).
4. Position appliance on counter allowing sufficient rear clearance from wall to tilt freely and
completely without obstruction.
5. Mark four corner locations of appliance base.
6. Remove appliance from counter and locate position of 4 holes as per Figure 1. Drill four
7/16" diameter holes.
7. Apply a continuous bead of Silastic or other equivalent sealant along the complete perimeter
edge of the appliance base.
8. Use 5/16-18 Hex Cap Screws with suitable flat washers to bolt down. Screw length must be
1-1/4 long plus counter top thickness.
9. Wipe off excess sealant.
10. A control box with power supply equivalent to Electrical Rating of appliance should be
located conveniently nearby.
5
WARNING: Disconnect electrical power supply and place a tag at
the disconnect switch to indicate you are on the circuit.
Hole pattern to mount kettle to table.
1.0 INSTALLATION INSTRUCTIONS (Continued)
1. A waterproof electrical connection for power supply to console housing must be provided.
2. Ground appliance to terminal provided inside console housing.
3. Turn power ON and check for proper operation.
FIGURE 1
6
Loading...