Blodgett KT-6DS-KTT, KT-10DS-KTT, KT-12DS-KTT, KT-(3)6DS-KTT, KT-6-10-DS-KTT General Manual

Project

Item No.

Quantity

 Model KT-6DS-KTT - 6 gallon (23 litres) direct steam kettle on 20” wide kettle

table

 Model KT-10DS-KTT - 10 gallon (38 litres) direct steam kettle on 30” wide

kettle table)

 Model KT-12DS-KTT - 12 gallon (45 litres) direct steam kettle on 30” wide

kettle table

 Model KT-(2)6DS-KTT - Two 6 gallon (23 litres) direct steam kettles on 40”

wide kettle table

 Model KT-(3)6DS-KTT - Three 6 gallon (23 litres) direct steam kettles on 63”

wide kettle table

 Model KT-6-10-DS-KTT - One 6 gallon (23 litres) and one 10 gallon (38

litres) direct steam kettle on 48” wide kettle table

 Model KT-6-12-DS-KTT - One 6 gallon (23 litres) and one 12 gallon (45

litres) direct steam kettle on 48” wide kettle table

KETTLE CONSTRUCTION

 304 stainless steel, one-piece welded construction
 2/3 jacketed kettle
 All exposed surfaces shall be stainless steel
 Sturdy cast, chrome plated stainless steel arms for sturdy support
 No exposed steam piping. The steam supply enters through the left kettle

support arm, through an integrated steam control valve into the jacket at
the rotary joint, down through the support arm.

 Rim shall be reinforced with a welded butterfly shaped pouring lip, for

pouring control and durability

 Right side handle for controlled pouring of kettle content
 Rear leg stops the kettle in the upright position
 ASME shop-inspected, stamped and registered with the National Board

for operation up to a maximum working pressure of 55 PSI

TABLE CONSTRUCTION

 Stainless steel with solid one piece welded construction.
 Raised marine edges and a 5” wide by 4” deep drain trough running the

width of the table, complete with drain fitting and strainer.

 Heavy 2” round tubular stainless steel support legs with adjustable bullet

feet.

 Table top work height ideal for operator convenience and efficiency.
 Sliding dump tray is designed to assist in pouring kettle contents into

pans or pots. Splashes or drips are diverted into the drain trough to elimi­nate spilling or splashing on floors etc. Dump tray lifts out for easy
cleanup and rolls along length of drain trough on nylon rollers.

 Front mounted steam control valves provided for kettle. All necessary

traps, piping and valves furnished and prepiped for single point utility
connection.

STANDARD FEATURES

 Double pantry faucet for each two kettles mounted. Front mounted hot

and cold faucet valves and swing spouts simplify kettle filling and clean­ing.

 One year parts and labor warranty*

* For all international markets, contact your local distributor.

BLODGETT

www.blodgett.com

44 Lakeside Avenue, Burlington, VT 05401 • Phone: [phone] • Fax: [phone]

OPTIONS AND ACCESSORIES

(AT ADDITIONAL CHARGE)

 Basket inserts
 Lift off cover
 Steam trap assemblies
 316 stainless steel interior for kettles

KT

Direct Steam Tabletop Tilting Kettles

on Kettle Tables

DIRECT STEAM TABLETOP TILTING KETTLE ON KETTLE TABLES

KT-(2)6DS-KTT shown

BLODGETT

www.blodgett.com

44 Lakeside Avenue, Burlington, VT 05401 • Phone: [phone] • Fax: [phone]

KT DIRECT STEAM KETTLES ON TABLE

SHORT FORM SPECIFICATIONS

Provide Blodgett tabletop 6DS-KTT (6 gallon) and/or 10DS-KTT (10 gallon) and/or 12DS-KTT (12
gallon) direct steam kettle on kettle table. Kettle mounting table shall be all stainless steel with con­venient work height and 5” wide drain trough with removable sliding dump tray. Front mounted indi­vidual steam control valves provided with direct steam kettles and hot & cold water controls stan­dard. Swing faucet positioned to fill one or two kettles as needed. Provide options and accessories
as indicated.

Printed in U.S.A. NOTE: FOR COMMERCIAL USE ONLY

NOTE: The company reserves the right to make substitutions of
components without prior notice.

KT-(3)6DS-KTT shown

Moveable

splash

guard

Drain &
strainer

1

C

5

4

15.63
(397)

6

(152)

14

(357)

A

TOP VIEW

2

3

2

3

See
note 2

See note 1

Steam

valve typ

B

17.13
(435)

rim height

Swing spout

faucet typ.

6

(152)

Hot & cold

water valves typ

7.25

(184)

FRONT VIEW

5

4

2
3

Bullet feet

w/mounting tabs

1.13 (29)

7.5

(191)

Full tilt

position

SIDE VIEW

SERVICE CONNECTIONS FOR KETTLES

NOTES:

1 Drain for sink 1-1/2” IPS
2 Cold water supply: 3/8” NPT (for faucet)
3 Hot water supply: 3/8” NPT (for faucet)
4 Drain consensate: ½” NPT
5 Steam in from power source: ½”NPT

1. T-brace required on all tables 60” and
longer.

2. Table sizes vary with size and number
of kettles.

3. Dimensions are in inches (mm).

APPROVAL/STAMP

P/N S00148 Rev A (4/11)

MAXIMUM PRESSURE:

55 PSI (379 kPa) (optional higher working pressure is available)

SHIPPING INFORMATION:

Approx. Weight:

KT-6DS-KTT 205 lbs. (93 kg)
KT-10DS-KTT 240 lbs. (109 kg)
KT-12DS-KTT 245 lbs. (111 kg)
KT-(2)6DS-KTT 285 lbs. (129 kg)
KT-(3)6DS-KTT 405 lbs. (184 kg)
KT-6-10-DS-KTT 346 lbs. (157 kg)
KT-6-12-DS-KTT 351 lbs. (159 kg)

A B C

KT-6DS-KTT

20 (508) 23 (508) 29 (737)

KT-10DS-KTT

30 (762) 25 (584) 23 (508)

KT-12DS-KTT

30 (762) 25 (584) 23 (508)

KT-(2)6DS-KTT

40 (1016) 23 (508) 29 (737)

KT-(3)6DS-KTT

63 (1600) 23 (508) 29 (737)

KT-6-10-DS-KTT

48 (1219) 25 (584) 23 (508)

KT-6-12-DS-KTT

48 (1219) 25 (584) 23 (508)