Blaupunkt NEW YORK 800 User Manual
Multimedia Navigation
New York 800
www.blaupunkt.com
Operating instructions
Controls – Device
1
2
3
4
5
6
7
8
9
1
button (Eject)
Eject a CD/DVD
2
MENU button
Call up main menu
In the main menu: Call up menu of active source
3
MAP button
Call up navigation
In navigation mode: Call up menu of active source
4
Microphone
5
Rotary/pushbutton
Short press: Switch on device
In operation: Mute audio source
Long press: Switch o device
Turn: Adjust volume
6
Infrared receiver for remote control
14
13
12
11
10
7
Reset button
Restoring the original factory settings of the device.
Caution! All personal settings will be lost!
8
Cover
9
SD card reader
Access only with open cover
:
Front USB socket (source USB 1)
Access only with open cover
;
Front AV-IN socket (source AV-IN 1)
Access only with open cover
<
Touchscreen user interface
=
MicroSD card reader for navigation data
Access only with open cover
>
DVD/CD drive
2
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
?
SRC button
Call up main menu
@
/ EJECT button
Eject a CD/DVD
A
AUDIO / MUSIC button
Select playback language (if available on DVD)
Call up folder overview of audio les
B
DISP button
Show information on the display
C
ZOOM button
Zoom in on image area
D
BAND button
Select waveband/memory bank
E
button
Answer a call
F
GOTO button
Directly select title, chapter, movie or playtime
Controls – Remote control
G
44
43
42
41
40
39
38
37
36
RPT A-B button
De ne range for repeat function
H
RPT button
Repeat function
I
SETUP button
Call up settings menu
J
button
Start and interrupt playback
Con rm settings
K
/ / / button
Navigate in menus and change settings
Tuning into stations manually ( / )
35
34
33
32
31
30
Starting station seek tuning ( / )
L
button
Slow-motion playback
M
Number buttons 0 - 9
N
/ MIX button
Random track play
O
/ SCN button
Scan function
P
MUTE button
Mute audio source
Q
button
Quit playback
R
VOL + / – button
Adjusting the volume
S
PIC button
Screen settings
T
/ button
Select title, chapter, movie
Fast searching
U
button
Ending/rejecting a phone call
V
CLEAR button
Delete last character of an entry
W
TITLE button
Call up title and chapter list
X
MENU button
Call up DVD menu
Y
ANGLE / VIDEO button
Select camera viewing angle (if available on DVD)
Call up folder overview of movies
Z
SUBTITLE / PHOTO button
Select subtitle language (if available on DVD)
Call up folder overview of images
[
button
Switching device on/o
\
EQ button
Call up equaliser menu
3
Contents
Safety notes ................................................................ 5
Symbols used ...........................................................................5
Road safety ................................................................................5
General safety notes ..............................................................5
Declaration of conformity .................................................... 5
Cleaning notes ............................................................ 5
Disposal notes............................................................. 5
Scope of delivery ........................................................ 6
Placing the device in operation ................................. 6
Switching on/o ......................................................................6
Volume ........................................................................................6
Main menu ................................................................................6
Radio mode ................................................................. 6
Start radio mode .....................................................................6
Select memory bank ..............................................................6
Tuning into a station ..............................................................6
Storing stations manually ....................................................7
Storing stations automatically (Travelstore) .................7
Switching RDS on/o ........................................................... 7
Tra c information ..................................................................7
Navigation ................................................................... 8
Loading navigation data ......................................................8
Download of map data .........................................................8
Starting the navigation .........................................................8
Initial startup ............................................................................8
Entering a destination ........................................................... 8
Address ......................................................................................8
Points of Interest ....................................................................9
Setting route options ......................................................... 10
Map Settings .......................................................................... 11
DVD/CD/USB/SDHC/iPod media playback ............. 12
Basic information ................................................................. 12
DVD/CD mode ...................................................................... 12
USB data carrier ....................................................................12
SDHC cards ............................................................................. 13
iPod/iPhone via USB ........................................................... 13
DVD movie playback .......................................................... 13
Audio playback of DVD/CD, USB, SDHC or
iPod/iPhone ........................................................................... 14
Video playback from DVD/CD, USB or SDHC ............. 14
Image playback from DVD/CD, USB or SDHC ............ 15
Bluetooth mode ........................................................ 16
Starting Bluetooth mode .................................................. 16
Registering Bluetooth devices ........................................ 16
Telephone mode - Bluetooth...........................................16
Bluetooth settings ............................................................... 17
Rear Seat Entertainment (RSE) ................................ 17
External audio/video sources .................................. 18
Sound settings .......................................................... 18
Volume distribution (fader/balance) ............................ 18
Equalizer .................................................................................. 18
Basic settings ............................................................ 19
Video ......................................................................................... 19
General .................................................................................... 19
Time .......................................................................................... 19
Sound ....................................................................................... 20
Language ................................................................................ 20
Bluetooth ................................................................................ 20
DVD ........................................................................................... 20
Volume ..................................................................................... 21
Useful information ................................................... 21
Warranty .................................................................................. 21
Service ...................................................................................... 21
Connection diagram ................................................ 22
Appendix ................................................................... 23
4
Safety notes | Cleaning notes | Disposal notes
Safety notes
The car sound system was manufactured according to
the state of the art and established safety guidelines.
Even so, dangers may occur if you do not observe the
safety notes in these instructions.
These instructions are intended to familiarise you with
the most important functions. Detailed information can
be found on the Internet under www.blaupunkt.com.
• Read these instructions carefully and completely
before using the car sound system.
• Keep the instructions at a location so that they
are always accessible to all users.
• Always pass on the car sound system to third parties
together with these instructions.
In addition, observe the instructions of the devices used
in conjunction with this car sound system.
Symbols used
These instructions employ the following symbols:
DANGER!
Warns about injuries
CAUTION!
Warns about damages to the DVD/CD drive
DANGER!
Warns about high volume
The CE mark con rms the compliance with EU
directives.
쏅 Identi es a sequencing step
• Identi es a listing
Road safety
Observe the following notes about road safety:
• Use your device in such a way that you can always
safely control your vehicle. In case of doubt, stop
at a suitable location and operate your device while
the vehicle is standing. As the driver, you may not use
the applications that will distract you from tra c (depending on the scope of functions of the device, e.g.
viewing videos, entering a destination).
• Follow the driving recommendations during the
route guidance only if you are not violating any
tra c regulations! Tra c signs and tra c regula-
tions have always priority over driving recommendations.
• Always listen at a moderate volume to protect
your hearing and to be able to hear acoustic warning signals (e.g. police sirens). During mute phases
(e.g. when changing the audio source), changing the
volume is not audible. Do not increase the volume
during this mute phase.
General safety notes
Observe the following note to protect yourself against
injuries:
Do not modify or open the device. The device contains
a Class 1 laser that can cause injuries to your eyes.
Use as directed
This car sound system is intended for installation and
operation in a vehicle with 12 V vehicle system voltage
and must be installed in a DIN slot. Observe the output
limits of the device. Repairs and installation, if necessary,
should be performed by a specialist.
Installation instructions
You may only install the car sound system yourself if you
are experienced in installing car sound systems and are
very familiar with the electrical system of the vehicle. For
this purpose, observe the connection diagram at the end
of these instructions.
Declaration of conformity
We, Blaupunkt AudioVision GmbH & Co. KG, a rm that
the device New York 800 ful ls the fundamental requirements and other relevant regulations of the EU Directive
1999/5/EC.
The declaration of conformity can be found on the Internet under www.blaupunkt.com.
Cleaning notes
Solvents, cleaning and scouring agents as well as dashboard spray and plastics care product may contain ingredients that will damage the surface of the car sound
system.
Use only a dry or slightly moistened cloth for cleaning the
car sound system.
Disposal notes
Do not dispose of your old unit in the household
trash!
Use the return and collection systems available to
dispose of the old device, the remote control and
exhausted batteries.
5
Scope of delivery | Startup | Radio mode
Scope of delivery
The scope of delivery includes:
• New York 800
• Remote control (incl. battery)
• TMC Tuner (for 1 011 103 800/802 only)
• MicroSD card with navigation data in the MicroSD
card slot (only for devices with navigation)
• GPS antenna
• External Bluetooth microphone
• Getting started
• Support frame
• Small parts set
• Installation material
• Connecting cable
Placing the device in operation
Caution!
Transport securing screws
Ensure that the transport securing screws are removed
before the startup of the device.
Switching on/o
Switching on/o with the rotary/pushbutton
쏅 For switch-on, press the rotary/pushbutton
쏅 For switch-o , hold the rotary/pushbutton
pressed for more than 2 seconds.
Switching on/o via vehicle ignition
If the car sound system is connected with the vehicle
ignition and it was switched o with the rotary/pushbutton 5, it is switched on or o with the ignition.
5
.
5
Main menu
In the main menu, you press the buttons on the touchscreen to call up the di erent sources and operating
modes.
쏅 Press the MENU button
The main menu is displayed.
As long as you do not select a new audio source, the
last active audio source is played back.
Note:
The gures used in these instructions are intended
to facilitate the explanations and details may deviate
from your device.
2
.
Radio mode
Start radio mode
쏅 In the main menu, press the Radio button.
The radio menu is displayed.
Volume
Adjusting the volume
You can adjust the volume in steps from 0 (o ) to 50
(maximum).
쏅 Turn the rotary/pushbutton
ume.
Muting the car sound system (Mute)
쏅 Brie y press the rotary/pushbutton 5 to mute the
device or to reactivate the previous volume.
6
5
to change the vol-
Select memory bank
Di erent memory banks and wavebands are available.
Up to 6 stations can be stored in each memory bank.
쏅 Press the
memory bank is displayed.
button repeatedly until the desired
Tuning into a station
Tuning into stations manually
쏅 Brie y press the
eral times to change the frequency in increments.
or button once or sev-
Radio mode
Enter broadcast frequency directly
If the frequency of the desired stations is known, it can
be entered directly via the touchscreen.
쏅 In radio mode, press the button.
A numeric keypad is displayed for the frequency
input.
쏅 Enter the frequency of the desired station with the
numeric keypad.
쏅 Press the
The radio menu is displayed, the station of the
frequency entered is played back.
Starting station seek tuning
쏅 Press the
to start station seek tuning.
The radio tunes into the next receivable station.
Note:
For the reception area Europe: In the FM waveband,
only tra c information stations are tuned into if the
priority for tra c information is switched on.
button.
or button for approx. 2 seconds
Storing stations manually
쏅 Select the desired memory bank with the but-
ton.
쏅 Set the desired station.
쏅 Press the
The menu for storing stations is displayed. 6 memory
locations are available that are displayed as buttons.
쏅 Press the button under which you want to store the
current station.
The station is stored, the radio menu is displayed
again.
button.
Storing stations automatically
(Travelstore)
With Travelstore, you can automatically search for and
store the 6 FM stations o ering the strongest reception
in the region in the memory bank FM1, FM2 or FM3.
쏅 Select an FM memory bank.
쏅 In the radio menu, press the
쏅 In the options menu, press the Travelstore button.
The tuner starts the automatic station seek tuning.
After the storing is completed, the radio plays the
station at memory location 1 of the previously selected memory bank.
Note:
With switched-on priority for tra c information, only
tra c information stations are stored.
button.
Switching RDS on/o
Many FM stations broadcast an RDS (Radio Data System)
signal in addition to their programme in the reception
area Europe that allows additional functions, such as the
display of the station name.
쏅 In the radio menu, press the
쏅 The options menu is displayed, the current setting is
shown after RDS.
쏅 In the options menu, press the RDS button to change
the setting.
쏅 Press the
The radio menu is displayed again.
button.
button.
Tra c information
In the reception region Europe, an FM station can identify tra c announcements via an RDS signal. If priority for
tra c reports is switched on, a tra c report is automatically switched through, even if the car sound system is
currently not in radio mode.
Note:
The volume is increased for the duration of the
switched-through tra c announcement. You can adjust the minimum volume for tra c announcements.
Switching priority for tra c announcements on/o
쏅 In the radio menu, press the TA button to switch the
priority for tra c announcements on or o .
The TA button is lit if the priority for tra c announce-
ments is switched on.
Setting the minimum volume for tra c
announcements
쏅 In the radio menu, press the
쏅 In the options menu, press the TA V OL button.
쏅 Adjust the desired volume with the
ton.
쏅 Press the
The radio menu is displayed again, the set volume
is stored.
button.
button.
or but-
7
Navigation
Navigation
Loading navigation data
The navigation software and map data are located on a
MicroSD card. For devices with navigation, the device is
delivered with the MicroSD card in the MicroSD card slot.
To be able to use the navigation, the MicroSD card must
be inserted in the card slot.
쏅 Open the cover of the card slot
CD tray.
쏅 Insert the MicroSD card with the printed side up into
the slot until it engages.
쏅 Close the cover of the slot.
Download of map data
To ensure that you have the latest version of the map
data when you purchase the New York 800, you have
30 days from the rst GPS positioning to download the
latest version of the map data once and free of charge
to the standard MicroSD card from the Internet at
www.naviextras.com.
You can always purchase map material from this site at
a later time.
Important note:
If the MicroSD card is lost or damaged, the navigation map license associated with the card will be lost.
In this case, the license must be purchased anew with
a new MicroSD card.
Starting the navigation
쏅 In the main menu, press Navigation to start the navi-
gation mode.
The navigation menu is displayed. If you start the
navigation for the rst time, the setup wizard is displayed.
Initial startup
If you start the navigation for the rst time, a setup wizard
appears which performs the basic settings for the navigation.
쏅 Adjust the language for the navigation. This can be
a di erent language from the other functions of the
NewYork800.
쏅 Con rm the selection with
The end-user license agreement is displayed.
쏅 Read the end-user license agreement. If you agree
with the terms and conditions, press
The con guration wizard starts.
쏅 Press
to continue.
=
next to the DVD/
.
.
쏅 Select a voice for the voice output of the navigation.
Various voices are available for the languages.
쏅 Con rm the selection with
쏅 Specify the time format and the units for the naviga-
tion. Next, press
On the next screen, you can perform your preferred
route settings.
쏅 If necessary, change the entries by pressing the dis-
played menu entries.
쏅 Press , after you adjusted the settings.
쏅 Touch
The navigation menu is displayed.
, to nish the con guration.
.
.
Entering a destination
Destinations can be entered in di erent ways: Via the address or as point of interest from the database of points
of interest. Points of interest can be sights, museums, stadiums, petrol stations.
Address
쏅 Open the navigation menu.
쏅 Press on Find.
The menu for the destination entry is displayed.
쏅 Press Find Address.
8
Loading...