Accessories
52
SUPPLIED: Instruction Manual, Two PR-33A x1/x10 Probes or equivalent,
AC Power Cord, Spare Fuse
OPTIONAL: PR-32A Demodulator Probe, PR-37A x1/x10/REF. Probe, PR-100A x100
Probe, PR-55 High Voltage x1000 Probe, LC-210A Carrying Case
2160A
VERTICAL AMPLIFIERS (CH 1 and 2)
Sensitivity 5mV/div to 1V/div x 5mag
Attenuator 1-2-5 sequence, plus x 5 gain step, Vernier control provide
fully adjustable
sensitivity between steps
range 1/1 to
at least 1/2.5
Accuracy ±3%, 5mV to 5V/div; ±5%, 1mV, 2mV/div
Input impedance 1MΩ ±2%
Input Capacitance 25pF±10%
Frequency Response DC to 60 MHz
Rise Time 5.8ns (Overshoot <
5%)
Operating Modes CH1, CH2, Dual, Alternate Chop
Polarity Reversal CH 2 invert
Maximum Input Voltage 400V (dc + AC Peak), 800 VAC p-p
SWEEP SYSTEM
Sweep Display Modes Main, Mix, Delay
Hold Off Time 5:1 continuously variable
Main Sweep
Sweep Speed 0.1µs/div. to 2.0s/div. in 1-2-5 sequence, 23 steps
Accuracy ±3%
Variable Time Control 5:1,uncalibrated, continuously variable between steps
Sweep Magnification 10 x , ±10%, extended sweep speed up to 10ns/div
Delay Sweep
Sweep Speed 0.1 µs/div. to 2.0s/div. in 1-2-5 sequence, 23 steps
Accuracy ±3%
Sweep Magnification 10 x , ±10%, extended sweep speed up to 10ns/div
Delay Time Position Variable control to locate desirable waveform for extending
Triggering
Trigger Coupling AUTO, NORM, TV-V, TV-H
Trigger Source CH1, CH2, ALT, EXT. LINE
Slope +/-
HORIZONTAL AMPLIFIER
(Input through channel 2 input)
X-Y Mode CH 1: Y axis. CH 2: X axis
Sensitivity Same as vertical channel 2
Accuracy ±3%, Y axis; ±5% X axis
Input Impedance Same as vertical channel 2
Frequency Response DC: DC to 1MHz (-3 dB). AC: 5 Hz ro 2 MHz (-3 dB)
X-Y Phase Difference 3˚ at at 50 kHz
Maximum Input Voltage Same as vertical channel 2
CH 2 Output (on rear panel)
Output Voltage 50 mV/div (nominal into 50 Ω load)
Output Impedance Approximately 50 Ω
Frequency Response 20Hz to 60MHz, -3dB into 50V
CRT
Type 6-inch rectangular with internal graticule
Display Area 8 x 10 div (1 div = 1 cm)
Accelerating Voltage 12 k
Phospor P31
Scale Illumination Continuously variable
Trace Rotation Electrical, front panel adjustable
COMPONENT TESTER
Components Tested Resistors, capacitors, inductors, and semiconductors
Test Voltage 6V rms maximum (open)
Test Current 11mA maximum (shorted)
Test Frequency Line frequency (60 Hz in USA)
Cal/Probe
Compensation Voltage 2.0 V p-p ±2% square wave, 1 kHz nominal
Sweep Output TTL level allows synchronization of external equipment
with scope sweep
Intensity Modulation
Input Signal TTL level, intensity increasing with more negative levels
Input Impedance Approx. 1 kΩ
Usable Freq. Range DC to 5 MHz
Maximum Input Voltage 5V (DC + AC peak)
Environment
Within Specified Accuracy 50˚ to 95˚F (10˚ to 35˚C), 85% maximum RH
Full Operation 32˚ to 122˚F (0˚ to +50˚C), 10 - 80% RH
Storage -22˚ to 158˚F (-30˚ to +70˚C), 10 - 90% RH
Power Requirements 110/120/220/240 V ±10%, 50/60 Hz
Dimensions (H x W x D) 12.76 x 15.68 x 5.2" (324 x 398 x 132mm)
Weight 16.75 lbs. (7.6kg)
Other Specifications
Specifications
model
2160A
■ 5mV/div sensitivity
■ 23 calibrated ranges-main
time base
■ 23 calibrated ranges-delayed
time base
■ Signal delay time
■ Component tester
■ Z axis input
■ Single sweep
Three Year Warranty
Loading...