Biostar TA790GX A2+ Owner's Manual

TA790GX A2+/TA790GX A2+ SE/TA790GX 128M

Setup Manual

FCC Information and Copyright

This equipment has been tested and found to comply with the limits of a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. There is no guarantee
that interference will not occur in a particular installation.

The vendor makes no representations or warranties with respect to the
contents here and specially disclaims any implied warranties of merchantability
or fitness for any purpose. Further the vendor reserves the right to revise this
publication and to make changes to the contents here without obligation to
notify any party beforehand.

Duplication of this publication, in part or in whole, is not allowed without first
obtaining the vendor’s approval in writing.

The content of this user’s manual is subject to be changed without notice and
we will not be responsible for any mistakes found in this user’s manual. All the
brand and product names are trademarks of their respective companies.

Table of Contents

Chapter 1: Introduction ............................................................ 1

1.1 Before You Start ................................................................................ 1

1.2 Package Checklist............................................................................. 1

1.3 Motherboard Features...................................................................... 2

1.4 Rear Panel Connectors ..................................................................... 4

1.5 Motherboard Layout......................................................................... 5

Chapter 2: Hardware Installation ............................................. 6

2.1 Installing Central Processing Unit (CPU)....................................... 6

2.2 FAN Headers...................................................................................... 8

2.3 Installing System Memory ................................................................ 9

2.4 Connectors and Slots....................................................................... 11

Chapter 3: Headers & Jumpers Setup ..................................... 14

3.1 How to Setup Jumpers .................................................................... 14

3.2 Detail Settings.................................................................................. 14

Chapter 4: (Hybrid) CrossFireX Function................................ 22

4.1 CrossFireX Requirements................................................................ 22

4.2 CrossFireX Installation .................................................................... 22

4.3 Hybrid CrossFire X Requirements .................................................. 23

4.4 Hybrid CrossFireX Installation....................................................... 23

4.5 Ope ration Modes Supporting List ................................................. 24

Chapter 5: RAID Functions ..................................................... 25

5.1 Operation System............................................................................ 25

5.2 Raid Arrays ...................................................................................... 25

5.3 How RAID Works............................................................................. 25

Chapter 6: T-Series BIOS & Software ..................................... 29

6.1 T-Series BIOS..................................................................................... 29

6.2 T-Series Software ............................................................................. 37

Chapter 7: Useful Help ............................................................ 47

7.1 Driver Installation Note.................................................................. 47

7.2 Extra Information............................................................................ 48

7.3 AMI BIOS Beep Code....................................................................... 49

7.4 Troubleshooting............................................................................... 50

Appendix: SPEC In Other Language........................................ 52

German.................................................................................................................. 52

France .................................................................................................................... 54

Italian..................................................................................................................... 56

Spanish ................................................................................................................... 58

Portuguese ............................................................................................................ 60

Polish...................................................................................................................... 62

Russian ................................................................................................................... 64

Arabic..................................................................................................................... 66

Japanese ................................................................................................................ 68

TA790GX A2+/TA790GX A2+ SE/TA790GX 128M

CHAPTER 1: INTRODUCTION

1.1 B

EFORE YOU START

Thank you for choosing our product. Before you start installing the
motherboard, please make sure you follow the instructions below:

 Prepare a dry and stable working environment with

sufficient lighting.

 Always disconnect the computer from power outlet

before operation.

 Before you take the motherboard out from anti-static

bag, ground yourself properly by touching any safely
grounded appliance, or use grounded wrist strap to
remove the static charge.

 Avoid touching the components on motherboard or the

rear side of the board unless necessary. Hold the board
on the edge, do not try to bend or flex the board.

 Do not leave any unfastened small parts inside the

case after installation. Loose parts will cause short
circuits which may damage the equipment.

 Keep the computer from dangerous area, such as heat

source, humid air and water.

1.2 PACKAGE CHECKLIST

IDE Cable X 1
Serial ATA Cable X 2
Serial ATA Power Cable X 1
Rear I/O Panel for ATX Case X 1
User’s Manual X 1
Fully Setup Driver CD X 1
DCCFX-P2 Paddle Card X 1
FDD Cable X 1 (optional)
USB 2.0 Cable X1 (optional)
S/PDIF out Cable X 1 (optional)

Note: The package contents may differ by area or your motherboard version.

1

Motherboard Manual

/

1.3 MOTHERBOARD FEATURES

Socket AM2+

CPU

FSB

Chipset

Super I/O

Main

Memory

Graphics Radeon HD 3300

IDE AMD SB750

SATA II AMD SB750

LAN Realtek RTL 8111C

Sound ALC888

Slots

AMD Athlon 64 / Athlon 64 FX

/ Sempron / Phenom p rocessors

Support HyperTransport 3.0

Supports up to 5.2 GT/s Bandwidth

AMD 790GX

AMD SB750

ITE 8718

Prov ides the mos t co mmonly used legacy

Super I/O functionality.

Low Pin Count Interface

DIMM Slots x 4

Each DIMM supports 256MB/512MB/

1GB/2GB/4GB DDR2

Max Memory Capicity 16GB

PCI slot x2 Supports PCI expansion cards

PCI Express Gen2 x16 slot x2 Supports PCI-E Gen2 x16 expansion cards

PCI Express Gen2 x1 slot x2 Supports PCI-E Gen2 x1 expansion cards

Athlon 64 X2

SPEC

AMD 64 Architecture enables 32 and 64 bit

computing

Supports Hyper Transport 3.0 and PowerNow

En viro nment Cont rol in it iat ives ,

H/W Mon itor

Fan Sp eed Cont ro ller

ITE's "S mart Guard ian" funct ion

Dual Channe l Mod e DDR2 me mory mo du le

Supports DDR2 533 / 667 / 800

Supports DDR2 1066 (by AM2+ CPU)

Register ed DIMM and ECC D IMM is not suppo rted

Onboard side port memory 64MB (TA790GX A2+)

Onboard side port memory 128MB (TA790GX 128M)

Max S hared Vid eo Memory is 512 MB

DX10/UVD/HDCP support

(Hybrid) Cros sFireX support (by ATI d r iver)

Ultra DMA 33 / 66 / 100 / 133 Bus Master Mode

supports PIO Mode 0~4,

Data transfer rates up to 3 Gb/s.

SATA Versio n 2. 0 s pecificat io n co mpl ian t.

RAID 0,1,5,1+0 support

10 / 100 Mb/s / 1Gb/s auto negotiation

Half / Full duplex capability

7.1channels audio out

Supports HD Audio

2

TA790GX A2+/TA790GX A2+ SE/TA790GX 128M

SPEC

Floppy connector x1 Each connector supports 2 Floppy drives

Printer Port connector x1 Each connector supports 1 Printer port

IDE Connector x1 Each connector supports 2 IDE device

SATA Connector x6 Each connector supports 1 SATA devices

Front Panel Connector x1 Supports front panel facilit ies

Front Audio Connector x1 Supports front panel audio function

CD-in Connector x1 Supports CD audio-in function

On Board

Connector

Back Panel

I/O

Board Size 225 mm (W) x 305 mm (L) ATX

OS Support Windows XP / VISTA

S/PDIF out connector x1 Supports digital audio out function

S/PDIF in connector x1 Support digital audio in function

CPU Fan header x1 CPU Fan power supply (with Smart Fan function)

System Fan head er x2 Sys tem Fan Po wer supply

CMOS clear header x1 Restore CMOS data to factory default

USB connector x3 Each connector supports 2 front panel USB ports

Serial port Connector x1 Connects to RS-232 Port

Power Connector (24pin) x1 Connects to Power supply

Power Connector (4pin) x2 Connects to Power supply

PS/2 Keyboard x1

PS/2 Mous e x1

HDMI po rt x1

VGA port x1

DVI-D port x1

LAN port x1

USB Port x4

Audio Jack x6

Connects to PS/2 Keyboard

Connects to PS/2 Mouse

Connect to HDTV

Connect to D-SUB monitor

Connect to DVI monitor

Connect to RJ-45 ethernet cab le

Connect t o USB devices

Provide Audio-In/Out and microphone connection

Biostar Reserves the right to add or remove support

for any OS With or without notice.

3

Motherboard Manual

1.4 REAR PANEL CONNECTORS

X PS/2 Mouse Port Y PS/2 Key board Port

HDMI Port

Z

The High-Definition Multimedia Interface (HDMI) is an all-digital audio/video interface
capable of transmitting uncompressed streams to a n AV receiver or a ny compatible digital
audio and/or video monitor, such as a digital television.

DVI-D VGA Port

[

The Digital Visual Interface (DVI) is a video interface transmitting digital video signals to
digital display de vices such as flat panel LCDs or digital projectors. The DVI-D connec tor
allows digital signals transmission only.

D-Sub VGA Port

\

Trans mit analog video signals to computer monitor or a ny other display panels equipped
with D -Sub VGA input.

USB 2.0 Port x 4

]

10/100/1000 Mbps LAN Port

^

Audio Jack x 6

_

Port 2-Channel 4-Channel 6-Channel/8-Channel

Blue Li ne-In Line - In Line- In
Green Line-Out Front Speaker Out Front Speaker Out
Pink Mic In Mic In Mic In
Orange Cente r/S ubwoo fer
Black Rear Speaker Out Rear Speaker Out Rear Speaker Out
Grey Side Speaker Out

NOTE: The HDMI and DVI-D ports both can provide digital video signals out-put function, but

4

these two interfaces canno t work at the same time. The chipset uses the same channe l
to control HDMI and DVI-D, so these ports ca nnot transmit video signal to different display
panels simultaneously.

TA790GX A2+/TA790GX A2+ SE/TA790GX 128M

1.5 MOTHERBOARD LAYOUT

JKBMS1

JHDMI1

VGA

JUSB1

JUSBLAN1

JAUDIO2

DVI

LAN

JUSB V1

JATXPWR3

JATXPWR1

JNFAN1

PEX16_2

AMD

79 0GX

JCFAN1

Socket AM2+

DIMMA1

DIMMB1

DIMMA2

JATXPWR2

DIMMB2

IDE1

Codec

JAUDI OF1

Note: represents the 1■

JCDIN1

PEX1_1

PEX1_2

JSPDIF_IN1

JSPDIF_OUT1

JPRNT1

PEX16_1

PCI1

PCI2

JCOM1

st

BAT1

JUSB V2

pin.

JUSB5

Super I/O

JUSB3

JUSB4

AMD

SB750

JSFAN1

BIOS

JCMOS1

FDD1

JPANEL1

SATA3

SATA2

LED_ D1
LED_ D2

SATA1

RSTSW1

PWRS W1

5

Motherboard Manual

CHAPTER 2: HARDWARE INSTALLATION

2.1 I

NSTALLING CENTRAL PROCESSING UNIT (CPU)

Step 1: Remove the socket protection cap.

Step 2: Pull the lever toward direction A from the socket and then raise the

lever up to a 90-degree angle.

Step 3: Look for the white triangle on socket, and the gold triangle on

CPU should point towards this white triangle. The CPU will fit only
in the correct orientation.

6

TA790GX A2+/TA790GX A2+ SE/TA790GX 128M

Step 4: Hold the CPU down firmly, and then close the lever toward direct

B to complete the installation.

Step 5: Put the CPU Fan on the CPU and buckle it. Connect the CPU

FAN power cable to the JCFAN1. This completes the installation.

Note: Please update the BIOS to the latest version while using AM2+ CPUs. Due to the latest CPU

transition, you may encounter the situation that the new system failed to boot while using new
AM2+ CPUs. In this case, please install one standard AM2 CPU to boot your system, and
update the latest BIOS from our website for AM2+ CPUs support.

7

Motherboard Manual

2.2 FAN HEADERS

These fan headers support cooling-fans built in the computer. The fan
cable and connector may be different according to the fan manufact urer.
Connect the fan cable to the connector while matching the black wire to
pin#1.

JCFAN1: CPU Fan Header

14

JNFAN1: NorthBridge Fan Header

JSFAN1: System Fan Header

JNFAN1

13

JSFAN1

Pin

1 Ground
2 +12V
3

FAN RPM r at e
sense

4 Smart Fan

Control (By Fan)

Pin Assignment

1 Ground
2 +12V
3

Assignment

FAN RPM
rate sense

13

Note:

The JCFAN1, JNFAN1, and JSFAN1 support 4-pin and 3-pin head connectors. When
connecting with wires onto connectors, please note that the red wire is the positive and
should be co nnected to pin#2, and the black wire is Ground and should be connected to
GND.

8

TA790GX A2+/TA790GX A2+ SE/TA790GX 128M

2.3 INSTALLING SYSTEM MEMORY

A. DDR2 Modules

DIMMA1

DIMMB1

DIMMA2

DIMMB2

1. Unlock a DIMM slot by pressing the retaining clips outward. Align a
DIMM on the slot such that the notch on the DIMM matches the
break on the Slot.

2. Insert the DIMM vertically and firmly into the slot until the retaining
chip snap back in place and the DIMM is properly seated.

9

Motherboard Manual

B. Memory Capacity

DIMM Socket

Location

DIMMA1 256MB/512MB/1GB/2GB/4GB

DIMMB1 256MB/512MB/1GB/2GB/4GB

DIMMA2 256MB/512MB/1GB/2GB/4GB

DIMMB2 256MB/512MB/1GB/2GB/4GB

DDR2 Module

Total Memory

Size

Max is 16GB.

C. Dual Channel Memory installation

To trigger the Dual Channel function of the motherboard, the memory module
must meet the following requirements:

Install memory module of the same density in pairs, shown in the following
table.

Dual Channel Status

Enabled O O X X

Enabled X X O O

Enabled O O O O

(O means memory installed, X means memory not installed.)

The DRAM bus width of the memory module must be the same (x8 or
x16)

DIMMA1

DIMMB1 DIMMA2 DIMMB2

10

TA790GX A2+/TA790GX A2+ SE/TA790GX 128M

2.4 CONNECTORS AND SLOTS

FDD1: Floppy Disk Connector

The motherboard provides a standard floppy disk connector that supports 360K,
720K, 1.2M, 1.44M and 2.88M floppy disk types. This connector supports the
provided floppy drive ribbon cables.

234

133

IDE1: IDE/ATAPI Connector

The motherboard has a 32-bit Enhanced IDE Controller that provides PIO Mode
0~4, Bus Master, and Ultra DMA 33/66/100/133 functionality.

The IDE connector can connect a master and a slave drive, so you can connect
up to two drives.

40

39

2

1

11

Motherboard Manual

PEX16_1: PCI-Express Gen2 x16 Slot (x16/x8 Speed)

- PCI-Express 2.0 compliant.

- PCI-Express Gen2 supports a raw bit-rate of 5.0Gb/s on the data pins.

- 2X bandwidth over the PCI-Express 1.1 architecture.

- x16 Speed Mode: Maximum theoretical realized bandwidth of 8GB/s

simultaneously per direction, for an aggregate of 16GB/s
totally. (Must with DCCFX-P2 in PEX16_2)

- x8 Speed Mode: Maximum theoretical realized bandwidth of 4GB/s
simultaneously per direction, for an aggregate of 8GB/s
totally. (Without DCCFX-P2 in PEX16_2 or using
CrossFireX)

- PEX16_1 slot is reserved for graphics or video cards. The design of this

motherboard supports dual PCI-Express graphics cards using CrossFireX
technology with multiple displays. When using CrossFireX, this slot is
master and runs with x8 speed.

- To make this slot run with x16 speed, please insert the Paddle Card

DCCFX-P2 into PEX16_2.

PEX16_2: PCI-Express Gen2 x16 Slot (x8 Speed)

- PCI-Express 2.0 compliant.

- PCI-Express Gen2 supports a raw bit-rate of 5.0Gb/s on the data pins.

- 2X bandwidth over the PCI-Express 1.1 architecture.

- x8 Speed Mode: Maximum theoretical realized bandwidth of 4GB/s

simultaneously per direction, for an aggregate of 8GB/s
totally.

- PEX16_2 slot is reserved for graphics or video cards. The design of this

motherboard supports dual PCI-Express graphics cards using CrossFireX
technology with multiple displays. This slot is slave when using CrossFireX.

- Insert the Paddle Card DCCFX-P2 into this slot will make PEX16_1 run

with x16 speed.

12

PEX16 _2

PE X1 6_1

TA790GX A2+/TA790GX A2+ SE/TA790GX 128M

PEX1_1/PEX1_2: PCI-Express Gen2 x1 Slots

- PCI-Express 2.0 compliant.

- Data transfer bandwidth up to 500MB/s per direction; 1GB/s in total.

- PCI-Express Gen2 supports a raw bit-rate of 5.0Gb/s on the data pins.

- 2X bandwidth over the PCI-Express 1.1 architecture.

PEX1_ 1

PE X1_2

PCI1~PCI2: Peripheral Component Interconnect Slots

This motherboard is equipped with 2 standard PCI slots. PCI stands for
Peripheral Component Interconnect, and it is a bus standard for expansion
cards. This PCI slot is designated as 32 bits.

PCI1

PCI2

13

Motherboard Manual

CHAPTER 3: HEADERS & JUMPERS SETUP

3.1 H

OW TO SETUP JUMPERS

The illustration shows how to set up jumpers. When the jumper cap is
placed on pins, the jumper is “close”, if not, that means the jumper is
“open”.

Pin opened Pin closed Pin1-2 closed

3.2 DETAIL SETTINGS

JPANEL1: Front Panel Header

This 16-pin connector includes Power-on, Reset, HDD LED, Power LED, and
speaker connection. It allows user to connect the PC case’s front panel switch
functions.

D

E

_

R

L

W

P

916

+

1

K

P

S

H

f

/

O

n

O

f

-

+

8

-

+

T

R

S

D

E

L

14

Pin Assignment Function Pin Assignment Function

1 +5V 9 N/A
2 N/A 10 N/A
3 N/ A 11 N/A N/A
4 Speaker
5 HDD LED (+) 13 Power LED (+)
6 HDD LED (-)
7 Ground 15 Power button
8 Reset control

Speaker
Connector

Hard drive
LED

Reset button

12 Power LED (+)

14 Power LED (-)

16 Ground

N/A

Power LED

Power-on button

TA790GX A2+/TA790GX A2+ SE/TA790GX 128M

JATXPWR2: AT X Power Source Connector

This connector allows user to connect 24-pin power connector on the ATX
power supply.

12

1

Pin Assignment Pin Assignment

13 +3.3V 1 +3.3V
14 -12V 2 +3.3V
15 Ground 3 Ground
16 PS_ON 4 +5V
17 Ground 5 Ground
18 Ground 6 +5V
19 Ground 7 Ground
20 NC 8 PW_OK
21 +5V 9 Standby Voltage+5V
22 +5V 10 +12V
23 +5V 11 +12V
24 Ground 12 +3.3V

24

13

JATXPWR3: AT X Power Source Connector

By connecting this connector, it will provide +12V to CPU power circuit.

1

4

23

Pin Assignment

1 +12V
2 +12V
3 Ground
4 Ground

Note:

Before power on the system, please make sure that both JATXPWR2 and JATXPWR3
connectors have been plugged-in.

15

Motherboard Manual

JATXPWR1: Auxiliary Power for Graphics

This connector is an auxiliary power connection for graphics cards. Exclusive
power for the graphics card provides better graphics performance.

JCMOS1: Clear CMOS Header

By placing the jumper on pin2-3, it allows user to restore the BIOS safe setting
and the CMOS data, please carefully follow the procedures to avoid damaging
the motherboard.

14

13

Pin 1-2 Close:

Normal Operation (default).

Pin

Assignment

1 +12V
2 Ground
3 Ground
4 VCC

16

13

13

Pin 2-3 Close:

Clear CMOS data.

※ Clear CMOS Procedures:

1. Remove AC power line.

2. Set the jumper to “Pin 2-3 close”.

3. Wait for five seconds.

4. Set the jumper to “Pin 1-2 close”.

5. Power on the AC.

6. Reset your desired password or clear the CMOS data.

TA790GX A2+/TA790GX A2+ SE/TA790GX 128M

SATA1~SATA3: Serial ATA Connectors

The motherboard has a PCI to SATA Controller with 6 channels SATA interface,
it satisfies the SATA 2.0 spec and with transfer rate of 3.0Gb/s.

SATA1 SATA2 SATA3

JUSB3~JUSB5: Headers for USB 2.0 Ports at Front Panel

This header allows user to connect additional USB cable on the PC front panel,
and also can be connected with internal USB devices, like USB card reader.

Pin

Assignment

1 +5V (fused)
2 +5V (fused)
3 USB­4 USB­5 USB+

JUSB5

JUSB3

2

JUSB4

10

6 USB+
7 Ground
8 Ground
9 Key

10 NC

1

9

17

Motherboard Manual

JAUDIOF1: Front Panel Audio Header

This header allows user to connect the front audio output cable with the PC front
panel. This header allows only HD audio front panel connector; AC’97 connector
is not acceptable.

JSPDIF_OUT1: Digital Audio-out Connector

This connector allows user to connect the PCI bracket SPDIF output header.

Pin Assignment

1 Mic Left in
2 Ground
3 Mic Right in
4 GPIO
5 Right line in
6 Jack Sense
7 Front Sense
8 Key

2

10

1

9

9 Left line in

10 Jack Sense

Pin

Assignment

1 +5V
2 SPDIF_OUT
3 Ground

JSPDIF_IN1: Digital Audio-in Connector

This connector allows user to connect the PCI bracket SPDIF input header.

18

13

13

Pin

1 +5V
2 SPDIF_IN
3 Ground

Assignment

TA790GX A2+/TA790GX A2+ SE/TA790GX 128M

JCDIN1: CD-ROM Audio-in Connector

This connector allows user to connect the audio source from the variaty devices,
like CD-ROM, DVD-ROM, PCI sound card, PCI TV turner card etc.

Assignment

Pin

1 Left Channel Input
2 Ground
3 Ground
4 Right Channel Input

14

JPRNT1: Printer Port Connector

This header allows you to connector printer on the PC.

2

1

Pin Assignment Pin Assignment

1 -Strobe 14 Ground

2 -ALF 15 Data 6

3 Data 0 16 Ground

4 -Error 17 Data 7

5 Data 1 18 Ground

6 -Init 19 -ACK

7 Data 2 20 Ground

8 -Scltin 21 Busy

9 Data 3 22 Ground

10 Ground 23 PE

11 Data 4 24 Ground

12 Ground 25 SCLT

13 Data 5 26 Key

25

19

Motherboard Manual

JCOM1: Serial port Connector

The motherboard has a Serial Port Connector for connecting RS-232 Port.

Pin Assignment

1 Carrier detect
2 Received data
3 Transmitted data
4 Data terminal ready
5 Signal ground
6 Data set ready
7 Request to send
8 Clear to send
9 Ring indicator

2

10

10 NC

1

9

JUSBV1/JUSBV2: Power Source Headers for USB Ports

Pin 1-2 Close:

JUSBV1: +5V for USB ports at JUSB1/JUSBLAN1.

JUSBV2: +5V for USB ports at JUSB3/JUSB4/JUSB5.

Pin 2-3 Close:

JUSBV1: +5V STB for USB ports at JUSB1/JUSBLAN1.

JUSBV2: +5V STB for USB ports at JUSB3/JUSB4/JUSB5.

1

JUSBV1

1

3

JUSBV2

13

3

Pin 1-2 close

1

3

Pin 2-3 close

20

TA790GX A2+/TA790GX A2+ SE/TA790GX 128M

On-Board LED Indicators

There are 2 LED indicators on the motherboard to show system status.

LED_D1
LED_D2

LED_D1 and LED_D2:

These 2 LED indicate system power on diagnostics.
Please refer to the table below for different messages:

LED_D2 LED_D1 Message

OFF OFF Abnormal: CPU / Chipset error.
OFF ON Memor y Error

ON OFF VGA Error
ON ON Norma l

On-Board Buttons

There are 2 on-board buttons.

PWRSW1:

This is an on-board Power Switch button.

RSTSW1:

This is an on-board Reset button.

RSTSW1

PWRSW1

21

Motherboard Manual

CHAPTER 4: (HYBRID) CROSSFIREX FUNCTION

4.1 C

ROSSFIREX REQUIREMENTS

Only Windows XP/Vista supports CrossFireX (Dual Video) function.

A pair of graphics cards with Radeon HD3650/HD3850/HD3870/HD4850/

HD4870 GPU.

The graphics card driver should support CrossFireX technology.

The power supply unit must provide at least the minimum power required by

the system, or the system will be unstable. A power supply above 500W is
recommended under CrossFireX mode.

4.2 CROSSFIREX INSTALLATION

Step 1: Insert the two CrossFireX-Ready graphics cards into PEX16_1 (Master)
and PEX16_2 (Slave)

PEX16_2(Slave)

Radeo n HD3 650
Pair of Radeon HD3850/

Radeon HD4850/HD4870

PEX16_1(Master)

HD3870

22

Notice: Make sure both the graphics cards are seated into slots
completely.

Step 2: Connect a 4-pin ATX power cable to Auxiliary Power Connector
(JATXPWR1), this will ensure the stabilization of your system.

Step 3: Connect the CrossFireX Bridge with two graphics cards. Installation
completes.

NOTE

For more detail information of hardware/software installation and configuration
of CrossFireX function, please visit following web-sites:

http://ati.amd.com/technology/crossfire/tutorials.html
http://ati.amd.com/technology/crossfire/howitworksdemo.html

TA790GX A2+/TA790GX A2+ SE/TA790GX 128M

4.3 HYBRID CROSSFIREX REQUIREMENTS

Only Windows Vista supports Hybrid CrossFireX function.

A graphics card with Radeon HD3450/HD3470 GPU.

The graphics card driver should support Hybrid CrossFireX technology.

The power supply unit must provide at least the minimum power required by

the system, or the system will be unstable. A power supply above 450W is
recommended under Hybrid CrossFireX mode.

4.4 HYBRID CROSSFIREX INSTALLATION

Step 1: Insert the Hybrid CrossFireX-Ready graphics card into PEX16_1
(Master), and insert the DCCFX-P2 Paddle Card into PEX16_2 (Slave).

PEX16_2(Slave)

PEX16_1(Master)

Notice: Make sure both cards are seated into slots completely.

Step 2: Connect a 4-pin ATX power cable to Auxiliary Power Connector
(JATXPWR1), this will ensure the stabilization of your system.

Step 3: In the graphics card configuration program, choose “Hybrid
CrossFireX” function. Installation completes.

DCCFX-P2
Paddle Card

Radeon HD 3450
Radeon HD 3470

NOTE

For more detail information of Hybrid CrossFireX function, please visit following
web-sites:

http://game.amd.com/us-en/crossfirex_hybrid.aspx
http://ati.amd.com/technology/hybridgraphics/index.html

23

Motherboard Manual

4.5 OPERATION MODES SUPPORTING LIST

Operation Mode

Model

Radeon HD3650 O O X

Radeon HD3850 O O X

Radeon HD3870 O O X

Radeon HD4850 O O X

Radeon HD4870 O O X

Radeon HD3450 O X O

Radeon HD3470 O X O

Radeon HD3870X2 O X X

Single Card

CrossFireX Hybrid CrossFireX

(O means Supported, X means Not Supported.)

24

TA790GX A2+/TA790GX A2+ SE/TA790GX 128M

CHAPTER 5: RAID FUNCTIONS

5.1 O

Supports Windows XP and Windows VISTA.

PERATION SYSTEM

5.2 RAID ARRAYS

RAID supports the following types of RAID arrays:

RAID 0: RAID 0 defines a disk striping scheme that improves disk read and write times for

many applications.

RAID 1: RAID 1 defines techniques for mirroring data.

RAID 1+0: RAID 1+0 combines the techniques used in R AID 0 and RAID 1.

RAID 5: RAID 5 provides fault to lerance and better utilization of disk capacity.

5.3 HOW RAID WORKS

RAID 0:

The controller “stripes” data across multiple drives in a RAID 0 array system. It breaks
up a large f ile into smalle r block s and perf orms d isk rea ds and wr ites acros s multip le
drives in parallel. The size of each block is determined by the stripe size parameter,
which you set during the creation of the RAID set based on the system environment. This
technique reduces overall disk access time and offers high bandwidth.

Features and Benefits

 Drives: Minimum 2, and maximum is up to 6 or 8. Depending on the

platform.

 Uses: Intended for non-critical data requiring high data throughput, or any

environment that does not require fault tolerance.

 Benefits: provides increased data throughput, especially for large files. No

capacity loss penalty for parity.

 Drawbacks: Does not deliver any fault tolerance. If any drive in the array

fails, all data is lost.

 Fault Tolerance: No.

Block 1
Blo ck 3
Blo ck 5

Block 2
Blo ck 4
Blo ck 6

25

Motherboard Manual

RAID 1:

Every read and write is actually carried out in parallel across 2 disk drives in a RAID 1
array system. The mirrored (backup) copy of the data can reside on the same disk or on a
second redundant drive in the array. RAID 1 provides a hot-standby copy of data if the
active volume or drive is corrupted or becomes unavailable because of a hardware failure.

RAID techniques can be applied for high-availability solutions, or as a form of automatic
backup that eliminates tedious manual backups to more expensive and less reliab le
media.

Features and Benefits

 Drives: Minimum 2, and maximum is 2.
 Uses: RAID 1 is ideal for small databases or any other application that

requires fault tolerance and minimal capacity.

 Benefits: Provides 100% data redundancy. Should one drive fail, the

controller switches to the other drive.

 Drawbacks: Requires 2 drives for the storage space of one drive.

Performance is impaired during drive rebuilds.

 Fault Tolerance: Yes .

26

Block 1
Block 2
Block 3

Block 1
Block 2
Block 3

TA790GX A2+/TA790GX A2+ SE/TA790GX 128M

RAID 1+0:

RAID 1 drives can be stripped using RAID 0 techniques. Resulting in a RAID 1+0
solution for improved resiliency, performance and rebuild performance.

Features and Benefits

 Drives: Minimum 4, and maximum is 6 or 8, depending on the platform.
 Benefits: Optimizes for both fault tolerance and performance, allowing for

automatic redundancy. May be simultaneously used with other RAID levels
in an array, and allows for spare disks.

 Drawbacks: Requires twice the available disk space for data redundancy,

the same as RAID level 1.

 Fault Tolerance: Yes .

Block 1
Block 3
Block 5

Block 1
Block 3
Block 5

Block 2
Block 4
Block 6

Block 2
Block 4
Block 6

27

Motherboard Manual

RAID 5:

RAID 5 stripes both data and parity information across three or more drives. It writes
data and parity blocks across all the drives in the array. Fault tolerance is maintained by
ensuring that the parity information for any given block of data is placed on a different
drive from those used to store the data itself.

Features and Benefits

 Drives: Min i mu m 3 .
 Uses: RAID 5 is recommended for transaction processing and general

purpose service.

 Benefits: An ideal combination of good performance, good fault tolerance,

and high capacity and storage efficiency.

 Drawbacks: Individual block data transfer rate same as a single disk. Write

performance can be CPU intensive.

 Fault Tolerance: Yes.

Disk 1

DATA 1

DATA 3
PA RI T Y

DATA 7
DATA 9
PA RI T Y

28

Disk 2

DATA 2

PA RI T Y

DATA 5

DATA 8
PA RI T Y
DATA 11

Disk 3

PA RI T Y

DATA 4

DATA 6

PA RI T Y
DATA 10
DATA 12

TA790GX A2+/TA790GX A2+ SE/TA790GX 128M

CHAPTER 6: T-SERIES BIOS & SOFTWARE

6.1 T-S

ERIES BIOS

T-Series BIOS Features

Overclocking Navigator Engine (O.N.E.)

Memory Integration Test (M.I.T., under Overclock Navigator Engine)

BIO-Flasher: Update BIOS file from USB Flash Drive or FDD

Self Recovery System (S.R.S)

Smart Fan Function

CMOS Reloading Program

!! WARNING !!

For better system performance, the BIOS firmware is being
continuously updated. The BIOS information described below in
this manual is for your reference only and the actual BIOS
information and settings on board may be different from this
manual. For further information of setting up the BIOS, please
refer to the BIOS Manual in the Setup CD.

A. Overclocking Navigator Engine (O.N.E.)

ONE provides two powerful overclocking engines: MOS and AOS for both
Elite and Casual overclockers.

Main Advanced

T-Series Settings

WARNING: Setting wrong values in below sections
may cause system to malfunction.

OverClock Navigator [Normal]

=========== Automate OverClock System ===========

Auto OverClock System [V6-Tech Engine]

============ Manual OverClock System ============

CPU Over Voltage [StartUp]
Memory Over Voltage [1.95V]
Chipset Over Voltage [1.15V]
HT Over Voltage [1.20V]
CPU Frequency [200]
> CPU FID/VID Control
> DRAM Timing Configuration
> Hyper Transport Configuration
> Memory Configuration

Integrated Memory Test [Disabled]

vxx.xx (C)Copyright 1985-200x, American Megatrends, Inc.

PCIPnP Boot

BIOS SETUP UTILITY

Chipset T-Series

Exit

Options

Normal
Automate OverClock
Manual OverClock

Select Screen
Select Item
Change Option

+-

General Help

F1

Save and Exit

F10

Exit

ESC

29

Motherboard Manual

Manual Overclock System (M.O.S.)

MOS is designed for experienced overclock users.
It allows users to customize personal overclock settings.

Main Advan ced P CIPnP Boot Chipset T-Series

T-Ser ies Settings

WARNI NG: Setting w rong va lues in below sections
may cause system to malfuncti on.

OverC lock Navigato r [Normal]

===== ====== Automate Over Clock System ==== =======

Auto OverClock Sys tem [V6-Tech Engine]

===== ======= Manua l OverC lock System = ========== =

CPU O ver Voltage [StartUp]
Memor y Over Voltag e [1.95V]
Chips et Over Volta ge [1.15V]
HT Ov er Voltage [1.20V]
CPU F requency [200]
> CPU FID/VID Cont rol
> DRA M Timing Conf igurati on
> Hyp er Transport Configu ration
> Mem ory Configura tion

Integ rated Memory Test [Disabled ]

Main Advan ced P CIPnP Boot Chipset T-Ser ies

T-Ser ies Settings

WARNI NG: Setting w rong va lues in below sections
may cause system to malfuncti on.

OverC lock Navigato r [Manual O verClock]

===== ====== Automate Over Clock System ==== =======

Auto OverClock Sys tem [V6-Tech Engine]

===== ======= Manua l OverC lock System = ========== =

CPU O ver Voltage [StartUp]
Memor y Over Voltag e [1.95V]
Chips et Over Volta ge [1.15V]
HT Ov er Voltage [1.20V]
CPU F requency [200]
> CPU FID/VID Cont rol
> DRA M Timing Conf igurati on
> Hyp er Transport Configu ration
> Mem ory Configura tion
Integ rated Memory Test [Disabled ]

CPU Overvoltage

This function will increase CPU stability when overclocking. However, the
CPU temperature will increase when CPU voltage is increased.

Memory Overvoltage

This function will increase memory stability when overclocking.

Chipset Overvoltage

This function will increase Northbridge and Southbridge chipset stability
when overclocking.

HT Overvoltage

This function will increase CPU stability when overclocking the HT ratio.

BIOS SE TUP UTILITY

Op tions
Normal
Automat e OverClock

Manual OverC lock

vxx.xx (C )Copyright 19 85-200x , American Me gatrends, Inc.

Exit

Op tions

Normal
Automate Ove rClock
Manual Ov erClock

Select Sc reen
Select It em
Change Op tion

+-

General H elp

F1

Save and Exit

F10

Exit

ESC

↓

BIOS SE TUP UTILITY

vxx.xx (C )Copyright 19 85-200x , American Me gatrends, Inc.

Exit

Op tions

Normal
Automate Ove rClock
Manual Ov erClock

Select Sc reen
Select It em

+-

Change Op tion

F1

General H elp

F10

Save and Exit

ESC

Exit

30

TA790GX A2+/TA790GX A2+ SE/TA790GX 128M

CPU Frequency

CPU Frequency is directly in proportion to system performance. To
maintain the system stability, CPU voltage needs to be increased also
when raising CPU frequency.

CPU FID/VID Control

Enter this function for more advanced CPU settings.

DRAM Timing Conf iguration

Enter this function for more advanced DRAM clock settings.

Hyper Transport Conf ig uratio n

Enter this function for more advanced Hyper Transport settings.

Memory Co nf ig urat io n

Enter this function for more advanced memory settings.

NOTE

Overclock is an optional process, but not a “must-do” process; it is
not recommended for inexperienced users. Therefore, we will not
be responsible for any hardware damage which may be caused by
overclocking. We also would not guarantee any overclocking
performance.

Automatic Overclock System (A.O.S.)

For beginners in overclock field, BET had developed an easy, fast, and
powerful feature to increase the system performance, named A.O.S.

Based on many tests and experiments, A.O.S. provides 3 ideal overclock
configurations that are able to raise the system performance in a single
step.

Main Advan ced P CIPnP Boot Chipset T-Ser ies

T-Ser ies Settings

WARNI NG: Setting w rong va lues in below sections
may cause system to malfuncti on.

OverC lock Navigato r [Normal]

===== ====== Automate Over Clock System ==== =======

Auto OverClock Sys tem [V6-Tech Engine]

===== ======= Manua l OverC lock System = ========== =

CPU O ver Voltage [StartUp]
Memor y Over Voltag e [1.95V]
Chips et Over Volta ge [1.15V]
HT Ov er Voltage [1.20V]
CPU F requency [200]
> CPU FID/VID Cont rol
> DRA M Timing Conf igurati on
> Hyp er Transport Configu ration
> Mem ory Configura tion

Integ rated Memory Test [Disabled ]

vxx.xx (C )Copyright 19 85-200x , American Me gatrends, Inc.

BIOS SE TUP UTILITY

Op tions
Normal

Automat e OverClock

Manual OverC lock

Op tions

Normal
Automate Ove rClock
Manual Ov erClock

+­F1
F10
ESC

Exit

Select Sc reen
Select It em
Change Op tion
General H elp
Save and Exit
Exit

31

Motherboard Manual

V6 Tech Engine

This engine will make a good over-clock performance.

Main Advan ced P CIPnP Boot Chipset T-Ser ies

T-Ser ies Settings

WARNI NG: Setting w rong va lues in below sections
may cause system to malfuncti on.

OverC lock Navigato r [Automate OverClock ]

===== ====== Automate Over Clock System ==== =======

Auto OverClock Sys tem [V6-Tech Engine]

===== ======= Manua l OverC lock System = ========== =

CPU O ver Voltage [StartUp]
Memor y Over Voltag e [1.95V]
Chips et Over Volta ge [1.15V]
HT Ov er Voltage [1.20V]
CPU F requency [200]
> CPU FID/VID Cont rol
> DRA M Timing Conf igurati on
> Hyp er Transport Configu ration
> Mem ory Configura tion

Integ rated Memory Test [Disabled ]

V8 Tech Engine

This engine will make a better over-clock performance.

Main Advan ced P CIPnP Boot Chipset T-Ser ies

T-Ser ies Settings

WARNI NG: Setting w rong va lues in below sections
may cause system to malfuncti on.

OverC lock Navigato r [Automate OverClock ]

===== ====== Automate Over Clock System ==== =======

Auto OverClock Sys tem [V8-Tech Engine]

===== ======= Manua l OverC lock System = ========== =

CPU O ver Voltage [StartUp]
Memor y Over Voltag e [1.95V]
Chips et Over Volta ge [1.15V]
HT Ov er Voltage [1.20V]
CPU F requency [200]
> CPU FID/VID Cont rol
> DRA M Timing Conf igurati on
> Hyp er Transport Configu ration
> Mem ory Configura tion

Integ rated Memory Test [Disabled ]

V12 Tech Engine

This engine will make a best over-clock performance.

Main Advan ced P CIPnP Boot Chipset T-Ser ies

T-Ser ies Settings

WARNI NG: Setting w rong va lues in below sections
may cause system to malfuncti on.

OverC lock Navigato r [Automate OverClock ]

===== ====== Automate Over Clock System ==== =======

Auto OverClock Sys tem [V12-Tech Engine]

===== ======= Manua l OverC lock System = ========== =

CPU O ver Voltage [StartUp]
Memor y Over Voltag e [1.95V]
Chips et Over Volta ge [1.15V]
HT Ov er Voltage [1.20V]
CPU F requency [200]
> CPU FID/VID Cont rol
> DRA M Timing Conf igurati on
> Hyp er Transport Configu ration
> Mem ory Configura tion

Integ rated Memory Test [Disabled ]

32

BIOS SE TUP UTILITY

vxx.xx (C )Copyright 19 85-200x , American Me gatrends, Inc.

BIOS SE TUP UTILITY

vxx.xx (C )Copyright 19 85-200x , American Me gatrends, Inc.

BIOS SE TUP UTILITY

vxx.xx (C )Copyright 19 85-200x , American Me gatrends, Inc.

Exit

Op tions

V6-Tech E ngine
V8-Tech E ngine
V12-Tech Eng ine

Select Sc reen
Select It em

+-

Change Op tion

F1

General H elp

F10

Save and Exit

ESC

Exit

Exit

Op tions

V6-Tech E ngine
V8-Tech E ngine
V12-Tech Eng ine

Select Sc reen
Select It em

+-

Change Op tion

F1

General H elp

F10

Save and Exit

ESC

Exit

Exit

Op tions

V6-Tech E ngine
V8-Tech E ngine
V12-Tech Eng ine

Select Sc reen
Select It em

+-

Change Op tion

F1

General H elp

F10

Save and Exit

ESC

Exit

TA790GX A2+/TA790GX A2+ SE/TA790GX 128M

Notices:

Not all types of AMD CPU perform above overclock setting ideally; the difference will be based on the
selected CPU model.

B. Memory Integration Test (M.I.T.)

This function is under “Overclocking Navigator Engine” item.
MIT allows users to test memory compatibilities, and no extra devices or

software are needed.

Step 1

The default setting under this item is “Disabled”; the condition parameter should
be changed to “Enable” to proceed this test.

Main Advan ced P CIPnP Boot Chipset T-Ser ies

T-Ser ies Settings

WARNI NG: Setting w rong va lues in below sections
may cause system to malfuncti on.

OverC lock Navigato r [Normal]

===== ====== Automate Over Clock System ==== =======

Auto OverClock Sys tem [V6-Tech Engine]

===== ======= Manua l OverC lock System = ========== =

CPU O ver Voltage [StartUp]
Memor y Over Voltag e [1.95V]
Chips et Over Volta ge [1.15V]
HT Ov er Voltage [1.20V]
CPU F requency [200]
> CPU FID/VID Cont rol
> DRA M Timing Conf igurati on
> Hyp er Transport Configu ration
> Mem ory Configura tion

Integ rated Memory Test [Disabled ]

vxx.xx (C )Copyright 19 85-200x , American Me gatrends, Inc.

Main Advan ced P CIPnP Boot Chipset T-Ser ies

T-Ser ies Settings

WARNI NG: Setting w rong va lues in below sections
may cause system to malfuncti on.

OverC lock Navigato r [Normal]

===== ====== Automate Over Clock System ==== =======

Auto OverClock Sys tem [V6-Tech Engine]

===== ======= Manua l OverC lock System = ========== =

CPU O ver Voltage [StartUp]
Memor y Over Voltag e [1.95V]
Chips et Over Volta ge [1.15V]
HT Ov er Voltage [1.20V]
CPU F requency [200]
> CPU FID/VID Cont rol
> DRA M Timing Conf igurati on
> Hyp er Transport Configu ration
> Mem ory Configura tion

Integ rated Memory Test [Enabled]

vxx.xx (C )Copyright 19 85-200x , American Me gatrends, Inc.

Step 2

Save and Exit from CMOS setup and reboot the system to activate this test.
Run this test for 5 minutes (minimum) to ensure the memory stability.

Step 3

When the process is done, change the setting back from “Enable” to “Disable”
to complete the test.

BIOS SE TUP UTILITY

↓

BIOS SE TUP UTILITY

Exit

Op tions

Enabled
Disabled

Select Sc reen
Select It em

+-

Change Op tion

F1

General H elp

F10

Save and Exit

ESC

Exit

Exit

Op tions

Enabled
Disabled

Select Sc reen
Select It em

+-

Change Op tion

F1

General H elp

F10

Save and Exit

ESC

Exit

33

Motherboard Manual

C. BIO-Flasher

BIO-Flasher is a BIOS flashing utility providing you an easy and simple way to
update your BIOS via USB pen drive or floppy disk.

The BIO-Flasher is built in the BIOS chip. To enter the utility, press <F12>
during the Power-On Self Tests (POST) procedure while booting up.

Updating BIOS with BIO-Flasher

1. Go to the website to download the latest BIOS file for the motherboard.

2. Then, save the BIOS file into a USB pen drive or a floppy disk.

3. Insert the USB pen drive or the floppy disk that contains the BIOS file to the
USB port or the floppy disk drive.

4. Power on or reset the computer and then
press <F12> during the POST process.
A select dialog as the picture on the right
appears.
Select the device contains the BIOS file and
press <Enter> to enter the utility.

34

5. The utility will show the BIOS
files and their respective
information. Select the proper
BIOS file and press <Enter>
then <Y> to perform the BIOS
update process.

6. After the update process, the utility will ask you to reboot the system.
Press <Y> to proceed. BIOS update completes.

z This utility only allows storage device with FAT32/16 format and single

partition.

z Shutting down or resetting the system while updating the BIOS will lead to

system boot failure.

TA790GX A2+/TA790GX A2+ SE/TA790GX 128M

D. Self Recovery System (S.R.S.)

This function can’t be seen under BIOS setup; and is always on whenever the
system starts up.
However, it can prevent system hang-up due to inappropriate overclock
actions.

When the system hangs up, S.R.S. will automatically log in the default BIOS
setting, and all overclock settings will be re-configured.

E. Smart Fan Function

Smart Fan Function is under “Smart Fan Configuration” in “Advanced Menu”.
This is a brilliant feature to control CPU/System Temperature vs. Fan speed.
When enabling Smart Fan function, Fan speed is controlled automatically by

CPU/System temperature.
This function will protect CPU/System from overheat problem and maintain the

system temperature at a safe level.

Main Advanced

Advanced Settings

WARNING: Setting wrong values in below sections
may cause system to malfunction.

> CPU Configuration
> SuperIO Configuration

> Smart Fan Configuration

> Hardware Health Configuration
> Power Configuration
> USB Configuration

PCIPnP Boot

BIOS SETUP UTILITY

Chipset T-Series

Exit

Select Screen
Select Item
Go to Sub Screen

Enter

General Help

F1

Save and Exit

F10

Exit

ESC

vxx.xx (C)Copyright 1985-200x, American Megatrends, Inc.

↓

Advanced

Smart Fan Configuration

CPU Smart Fan [Disabled]

Smart Fan Calibration
Control Mode
Fan Ctrl OFF( C)

Fan Ctrl On( C)
Fan Ctrl Start value
Fan Ctrl Sensitive

o

o

vxx.xx (C)Copyright 1985-200x, American Megatrends, Inc.

BIOS SETUP UTILITY

When you choice [Auto]
,[3Pin] or [4Pin],
please run the
calibration to define
the Fan parameters for
Smart Fan control

Select Screen
Select Item
Change Option

+-

General Help

F1

Save and Exit

F10

Exit

ESC

35

Motherboard Manual

Smart Fan Calibration

Choose this item and then the BIOS will automatically test and detect the
CPU/System fan functions and show CPU/System fan speed.

Control Mode

This item provides several operation modes of the fan.

Fan Ctrl OFF(℃)

If the CPU/System temperature is lower than the set value, the CPU/
System fan will turn off. The range is from 0~127, with an interval of 1.

Fan Ctrl On(℃)

The CPU/System fan starts to work when CPU/System temperature
arrives to this set value. The range is from 0~127, with an interval of 1.

Fan Ctrl Start Value

When CPU/System temperature arrives to the set value, the CPU/System
fan will work under Smart Fan Function mode. The range is from 0~127,
with an interval of 1.

Fan Ctrl Sensitive

Increasing the value of slope PWM will raise the speed of CPU/System fan.
The range is from 1~127, with an interval of 1.

F. CMOS Reloading Program

It allows users to save different CMOS settings into BIOS-ROM.
Users are able to reload any saved CMOS setting for customizing system
configurations. Moreover, users are able to save an ideal overclock setting
during overclock operation.
There are 10 sets of record addresses in total, and users are able to name the
CMOS data according to personal preference.

Main Advanced

Exit Options

Save Changes and Exit
Discard Changes and Exit
Discard Changes

Load Optimal Defaults

CMOS Backup Function

PCIPnP Boot

BIOS SETUP UTILITY

CMOS Backup Func

CMOS Data Reload

CMOS Data

Chipset T-Series

Save

Exit

36

Security Settings

> Security

vxx.xx (C)Copyright 1985-200x, American Megatrends, Inc.

Select Screen
Select Item
Go to Sub Screen

Enter

General Help

F1

Save and Exit

F10

Exit

ESC

TA790GX A2+/TA790GX A2+ SE/TA790GX 128M

l

6.2 T-SERIES SOFTWARE

Installing T-Series Software

1. Insert the Setup CD to the optical drive. The drivers installation program
would appear if the Auto-run function has been enabled.

2. Select Software Installation, and then click on the respective software
title.

3. Follow the on-screen instructions to complete the installation.

Launching T-Series Software

After the installation process, you will see the software icon “T-Utility
OverClock III” / “HW Monitor” / “eHOT Line” / “Tseries BIOS Update” appears
on the desktop. Double-click the icon to launch T-Series utility.

OverClock 3

OverClock 3 is equipped with friendly interface and solid over-clock features, and it
will help you easily do over-clocking under windows environment.

Double-click the desktop icon, OverClock 3 will be launched; the first window
you will see is Main Panel. In this panel you will see current CPU Speed and

CPU/Memory/PCI-E/PCI Clock.

Open

Over Clock

Panel

Ope n a s ave d set ti n g/
Save current settings

Open

Ab ou t Pane

Open

Open
Over Voltage

Over Voltage
Panel

Panel

ON/OFF

37

Motherboard Manual

Over Clock Panel

Restore Default Settings

AUTO Over-Clock

Manual Adjust CPU Clock

Test & Apply Manual Settings

V3/V 6/V9 Engi ne
Real-time Over-clock

AUTO

User can click t his button and the utility will set the best and stable
performance and frequency automatically. A warning dialog as below will
show up to notify you that the system may become unstable, click on “OK”
to continue.

38

TA790GX A2+/TA790GX A2+ SE/TA790GX 128M

Then the utility will execute a series of testing until system fail. Then
system will do fail-safe reboot by using Watchdog function. After reboot,
launch the utility again and the utility will load the previously verified best
and stable frequency.

V3 / V6 / V9

Provide user the ability to do real-time over-clock adjustment. For
beginners in over-clock field, this is a powerful feature to increase system
performance.

 V3 Engine

This engine will make a good over-clock performance.

 V6 Engine

This engine will make a better over-clock performance.

 V9 Engine

This engine will make a best over-clock performance.

TEST

You can also manually adjust CPU clock by pressing +/- button or moving
the level bar. After manually adjust the CPU clock, you should click

TEST button and the utility will proceed a testing for current frequency. If
the testing is ok, then the current frequency will be saved into system
registry. If the testing fails, system will do a fail-safe rebooting. After reboot,
the utility will restore to the hardware default setting.

Warning

Manually over-clock is potentially dangerous, especially when the over-clocking
percentage is over 110 %. We strongly recommend you test every speed you
over-clock by click the TEST button. Or, you can just click AUTO over-clock
button and let the Utility automatically get the best result for you.

RESET

Click t his button and the utility will restore all values to the hardware
default setting.

39

Motherboard Manual

Over Voltage Panel

Manual Adjust
CPU/Memory/Chipset/FSB Voltage

CPU Voltage

This function allows user to adjust CPU voltage. Click on “+” to increase
or “-“ to decrease the CPU voltage.

Memory Voltage

This function allows user to adjust Memory voltage. Click on “+” to
increase or “-“ to decrease the Memory voltage.

Chip Voltage

This function allows user to adjust Chipset voltage. Click on “+” to
increase or “-“ to decrease the Chipset voltage.

FSB Voltage

This function allows user to adjust FSB voltage. Click on “+” to increase
or “-“ to decrease the FSB voltage.

40

TA790GX A2+/TA790GX A2+ SE/TA790GX 128M

About Panel

In this panel, you can get model
name and other system information
that may related to over-clocking.
You can also get the version number
of this software.

Note

Because the Over Clock and Over
Voltage features are controlled by
several separate chipset, the utility
divides these features to separate
panels. If one chipset is not on
board, the correlative button in Main
panel will be disabled, but it will not
interfere with other panels’ functions.
This property can make the utility
more robust.

Hardware Monitor

HW Monitor is a monitor utility that helps you to maintain the health of the PC.
It provides real-time information of CPU/GPU/System temperat ure, fan speed,
and voltage.

Thi s area sh ows vol t age i nfor mati on

Vol t age Pa nel Fan Pa nel

Thi s area sh ows CPU in f orma tion

Thi s area s hows CPU/ Syst em t emp erat ure

Tu rn t o Fa n Pa nel

Thi s area sh ows CPU/ Syst em f an spe ed

Turn to Voltage Panel

41

Motherboard Manual

e

eHot-Line (Optional)

eHot-Line is a convenient utility that helps you to contact with our
Tech-Support system. This utility will collect the system information which is
useful for analyzing the problem you may have encountered, and then send
these information to our tech-support department to help you fix the problem.

Before you use this uti lity, plea se set Outlook Express as your default e-mail clie nt applicatio n program.

rep resents important

*

information t hat you
must provi de. Withou t
this informat ion, you may
not be able to send ou t
the mail.

This block will show
the infor mation which
would be collect ed in
the mail.

Send the mail ou t.

Describe co ndition

*

of your syst em.

Save these information to a .txt fil

Exit this dialog.

Select your area or

*

the area clos e to yo u.

Provid e the e-mail
addres s that you woul d
like to send the copy to.

Provide t he name of

*

the memory module
manufactu rer.

Provid e the name of
the power supply
manufac turer and the
model no .

After filling up this information, click “Send”
to send the mail out. A warning dialog would
appear asking for your confirmation; click
“Send” to confirm or “Do Not Send” to cancel.

If you want to save this information to a .txt file, click “Save As…” and then you
will see a saving dialog appears asking you to enter file name.

42

Enter the file name and then click
“Save”. Your system information

will be saved to a .txt file.

We will not share customer’s data with any other third parties,
so please feel free to provide your system information while using
eHot-Line service.

TA790GX A2+/TA790GX A2+ SE/TA790GX 128M

Open the saved .txt file, you will see
your system information including
motherboard/BIOS/CPU/video/
device/OS information. This
information is also concluded in the
sent mail.

If you are not using Outlook Express as your default e-mail client
application, you may need to save the system information to a .txt file
and send the file to our tech support with other e-mail application.
Go to the following web

http://www.biostar.com.tw/app/en-us/about/contact.php for getting

our contact information.

43

Motherboard Manual

BIOS Update

BIOS Update is a convenient utility which allows you to update your
motherboard BIOS under Windows system.

AWARD BIOS AMI BIOS

Clear CMOS function

(Only for AWARD BIOS)

Show current BIOS information

Save current BIOS

to a .bin f ile

Update BIOS

with a BIOS file

Online Update function

(Only for AMI BIOS)

<Backup BIOS>

Once click on this button, the saving
dialog will show. Choose the
position to save file and enter file
name. (We recommend that the file
name should be English/number
and no longer than 7 characters.)
Then click Save.

44

After the saving process, finish
dialog will show. Click on OK to

complete the BIOS Backup
procedure.

TA790GX A2+/TA790GX A2+ SE/TA790GX 128M

<Update BIOS>

Before doing this, please download the proper BIOS file from the website.

For AWARD BIOS, update BIOS procedure
should be run with Clear CMOS function, so
please check on Clear CMOS first.

Then click Update BIOS button, a
dialog will show for asking you backup
current BIOS. Click Yes for BIOS
backup and refer to the Backup BIOS
procedure; or click No to skip this
procedure.

After the BIOS Backup procedure, the
open dialog will show for requesting the
BIOS file which is going to be updated.
Please choose the proper BIOS file for
updating, then click on Open.

The utility will update BIOS with the
proper BIOS file, and this process may
take minutes. Please do not open any
other applications during this process.

After the BIOS Update process, click on
OK to restart the system.

While the system boots up and the full screen logo shows, press <Delete>
key to enter BIOS setup.

In the BIOS setup, use the Load Optimized Defaults function and then Save and
Exit Setup to exit BIOS setup. BIOS Update is completed.

45

Motherboard Manual

<Online Update> (for AM I BIOS only)

Automatically download and update the latest BIOS via internet; make sure
that the computer is connected to the internet before using this function.

After clicking on the Onlinr Update
button, the utility will search for the
latest BIOS from internet. If there is
a new BIOS version, the utility will
ask you to download it. Click Yes to
proceed.

If there is no other newer BIOS
version, the utility will also tell you that
your BIOS has been the latest version.

Download completes; the utility will
ask you to program (update) the
BIOS. Click Yes to proceed.

The programing procedure may take minutes, please do not make any operation
during the programing process.

After the updating process, the utility will
ask you to reboot the system. Click OK
to reboot.

While the system boots up and the full screen logo shows, press
key to enter BIOS setup.

In the BIOS setup, use the Load Optimized Defaults function and then Save and
Exit Setup to exit BIOS setup. Online Update is completed.

<Delete>

All the information and content above about the T-Series software are subject to be
changed without notice. For better performance, the software is being continuously
updated. The information and pictures described above are for your reference only.
The actual information and settings on board may be slightly different from this manual.

46

TA790GX A2+/TA790GX A2+ SE/TA790GX 128M

CHAPTER 7: USEFUL HELP

7.1 D

RIVER INSTALLATION NOTE

After you installed your operating system, please insert the Fully Setup
Driver CD into your optical drive and install the driver for better system
performance.

You will see the following window after you insert the CD

The setup guide will auto detect your motherboard and operating system.

Note:

If this window didn’t show up after you insert the Driver CD, please use file browser to
locate and execute the file SETUP.EXE under your optical drive.

A. Driver Installation

To install the driver, please click on the Driver icon. The setup guide will
list the compatible driver for your motherboard and operating system.
Click on each device driver to launch the installation program.

B. Software Installation

To install the software, please click on the Software icon. The setup guide
will list the software available for your system, click on each software title
to launch the installation program.

C. Manual

Aside from the paperback manual, we also provide manual in the Driver
CD. Click on the Manual icon to browse for available manual.

Note:

You will need Acrobat Reader to open the manual file. Please download the latest version
of Acrobat Reader software from

http://www.adobe.com/products/acrobat/readstep2.html

47

Motherboard Manual

7.2 EXTRA INFORMATION

CPU Overheated

If the system shutdown automatically after power on system for
seconds, that means the CPU protection function has been activated.

When the CPU is over heated, the motherboard will shutdown
automatically to avoid a damage of the CPU, and the system may not
power on again.

In this case, please double check:

1. The CPU cooler surface is placed evenly with the CPU surface.

2. CPU fan is rotated normally.

3. CPU fan speed is fulfilling with the CPU speed.

After confirmed, please follow steps below to relief the CPU protection
function.

1. Remove the power cord from power supply for seconds.

2. Wait for seconds.

3. Plug in the power cord and boot up the system.

Or you can:

1. Clear the CMOS data.
(See “Close CMOS Header: JCMOS1” section)

2. Wait for seconds.

3. Power on the system again.

48

TA790GX A2+/TA790GX A2+ SE/TA790GX 128M

7.3 AMI BIOS BEEP CODE

Boot Block Beep Codes

Number of Beeps Description

1 No media present. (Insert diskette in floppy drive A:)

2

3 Insert next diskette if multiple diskettes are used for recovery
4 Flash Programming successful
5 File read error

7 No Flash EPROM detected
10 Flash Erase error
11 Flash Program error
12 “AMIBOOT.ROM” file size error

13

POST BIOS Beep Codes

Number of Beeps Description

1 Memory refresh timer error

3 Base memory read/write test error

6 Keyboard controller BAT command failed

7 General exception error (processor exception interrupt error)

8 Display memory error (system video adapter)

“AMIBOOT.ROM” file not found in root directory of diskette in
A:

BIOS ROM image mismatch (file layout does not match
image present in flash device)

Troubleshooting POST BIOS Beep Codes

Number of Beeps Troubleshooting Action

1, 3 Reseat the memory, or replace with known good modules.

Fatal error indicating a serious problem with the system.
Consult your system manufacturer. Before declaring the
motherboard beyond all hope, eliminate the possibility of
interference by a malfunctioning add-in card. Remove all
expansion cards except the video adapter.

6, 7

8

z If beep codes are generated when all other expansion

cards are absent, consult your system manufacturer’s
technical support.

z If beep codes are not generated when all other expansion

cards are absent, one of the add-in cards is causing the
malfunction. Insert the cards back into the system one at a
time until the problem happens again. This will reveal the
malfunctioning card.

If the system video adapter is an add-in card, replace or
reseat the
video adapter. If the video adapter is an integrated part of the
system board, the board may be faulty.

49

Motherboard Manual

7.4 TROUBLESHOOTING

Probable Solution

1. No power to the system at all
Power light don’t illuminate, fan
inside power supply does not turn
on.

2. Indicator light on keyboard does
not turn on.

System inoperative. Keyboard lights
are on, power indicator lights are lit,
and hard drive is spinning.

System does not boot from hard disk
drive, can be booted from optical drive.

System only boots from optical drive.
Hard disk can be read and applications
can be used but booting from hard disk
is impossible.

Screen message says “Invalid
Configuration” or “CMOS Failure.”

Cannot boot system after installing
second hard drive.

1. Make sure power cable is
securely plugged in.

2. Replace cable.

3. Contact technical support.

Using even pressure on both ends of
the DIMM, press down firmly until the
module snaps into place.

1. Check cable running from disk to
disk controller board. Make sure
both ends are securely plugged
in; check the drive type in the
standard CMOS setup.

2. Backing up the hard drive is
extremely important. All hard
disks are capable of breaking
down at any time.

1. Back up data and applications
files.

2. Reformat the hard drive.
Re-install applications and data
using backup disks.

Review system’s equipment. Make sure
correct information is in setup.

1. Set master/slave jumpers
correctly.

2. Run SETUP program and select
correct drive types. Call the drive
manufacturers for compatibility
with other drives.

50

TA790GX A2+/TA790GX A2+ SE/TA790GX 128M

This page is intentionally left blank.

51

Motherboard Manual

APPENDIX: SPEC IN OTHER LANGUAGE

G

ERMAN

Sp ezif ika tio nen

Sockel AM2+

CPU

FSB

Chipsatz

Super E/A

Arbeitsspeich

er

Grafik Radeon HD 3300

IDE AMD SB750

SATA II AMD SB750

LAN Realtek RTL 8111C

Audio-Codec ALC888

Steckplätz e

AMD Athlon 64 / Athlon 64 FX / Athlon 64

X2 / S empron / Ph enom Prozess oren

Unterstützt HyperTransport 3.0 mit einer

Bandbreite von bis zu 5.2 GT/s

AMD 790GX

AMD SB750

ITE 8718

Biet et die h äuf ig verwendeten alten Sup er

E/A-Funktionen.

Low Pin Count-Schnittstelle

DDR2 DIMM-Steckplätze x 4

Jeder DIMM unterstützt

256MB/512MB/1GB/2GB/4GB DDR2.

Max. 16GB Arbeitsspeicher

PCI Steckp latz x2

PCI Express Gen2 x16 Steckplatz x2

PCI Express Gen2 x1 Steckplatz x2

Die AMD 64-Architektur unterstützt eine 32-Bit- und

64-Bit-Datenverarbeitung

Unterstützt Hyper Transport 3.0 und PowerNow

Umgebungskontrolle,

Hardware-Überwachung

Lüfterdrehzah l-Controller

"Smart Guardian"-Funktion von ITE

Dual-Kanal DDR2 Speichermodul

Unterstützt DDR2 533 / 667 / 800

Unterstützt DDR2 1066 (by AM2+ CPU)

registrierte DIMMs. ECC DIMMs werden nicht

unterstützt.

Onboard side port memory 64MB (TA790GX A2+)

Onboard side port memory 128 MB (TA790GX 128M)

Max. 512MB gemeinsam benutzter Videospeicher

Unterstützt DX10/UVD/HDCP

Unterstützt (Hybrid) CrossFireX (by ATI driver)

Ultra DMA 33 / 66 / 100 / 133 Bus Master-Modus

Unterstützt PIO-Modus 0~4,

Datentransferrate b is zu 3Gb/s

Konform mit der SATA-Spezifikation Version 2.0.

Unterstützt RAID 0,1,5,1+0

10 / 100 / 1000 Mb/s Auto-Negotiation

Halb-/ Vollduplex-Funktion

7.1-Kanal-Audioausgabe

Unterstützt High-Definition Audio

52

TA790GX A2+/TA790GX A2+ SE/TA790GX 128M

Sp ezif ika tio nen

Diskettenlaufwerkanschluss x1 Jeder Anschluss unterstützt 2 Diskettenlaufwerke

Druckeranschluss Anschluss x1 Jeder Anschluss unterstützt 1 Druckeranschluss

IDE-Anschluss x1 Jeder Anschluss unterstützt 2 IDE-Laufwerke

SATA-Anschluss x6 Jeder Anschluss unterstützt 1 SATA-Laufwerk

Fronttafelanschluss x1 Unterstützt die Fronttafelfunktionen

Front-Audioanschluss x1 Unterstützt die Fronttafel-Audioanschlussfunktion

CD-IN-Anschluss x1 Unterstützt die CD Audio-In-Funktion

S/PDIF Ausgangsanschluss x1 Unterstützt die d igitale Audioausgabefunktion

Onboard-Ans

chluss

Rückseiten-E

/A

Platinengröße 225 mm (B) X 305 mm (L) ATX

OS-Unterstüt

zung

S/PDIF Eingangsanschluss x1 Unterstützt die digitale Audioeingabefunktion

CPU-Lüfter-Sockel x1

System-Lüfter-Sockel x2 System-Lüfter-Stromversorgungsanschluss

"CMOS löschen"-Sockel x1

USB-Anschluss x3

Serieller Anschluss x1

Stromanschluss (24-polig) x1

St romansch luss (4- pol ig ) x2

PS/2-Tastatur x1

PS/2-Maus x1

HDMI-Anschluss x1

VGA-Anschluss x1

DVI-D-Anschluss x1

LAN-Anschluss x1

USB-Anschluss x4

Audioanschluss x6

Windows XP / VISTA

CPU-Lüfterstromversorgungsanschluss (mit Smart

Fan -F un ktio n)

Jeder Anschluss unterstützt 2

Fronttafel-USB-Anschlüsse

Biostar behält sich das Recht vor, ohne Ankündigung

die Unterstützung für ein Betriebssystem

hinzuzufügen oder zu entfernen.

53

Motherboard Manual

FRANCE

Socket AM2+

UC

Bus frontal

Chipset

Super E/S

Mémoire
principale

Graphiques Radeon HD 3300

IDE

SATA II

LAN Realtek RTL 8111C

Codec audio ALC888

Connecteur
embarqu é

Processeurs AMD Athlon 64 / Athlon 64 FX /
Athlon 64 X2 / Sempron / Phenom

Prend en charge Hyp er Transport 3.0 jusqu'à
une bande passante de 5.2 GT/s

AMD 790GX

AMD SB750

ITE 8718

Fournit la fonctionnalité de Super E/S
patrimoniales la plus utilisée.
Int e rfa ce à faib le co mpte de b roches

Fentes DDR2 DIMM x 4
Chaque DIMM prend en charge des DDR2 de

256 Mo/512 Mo/1 Go/2 Go/4 Go
Capacit é mémo ir e max ima le de 16 Go

AMD SB750

AMD SB750

Fente PCI x2
Fente PCI Express Gen2 x16 x2 Fentes

Fente PCI Express Gen2 x1 x2

Connecteur de disquette x1

Connecteur de Port d'imprimante x1

SPEC

L'architecture AMD 64 permet le calcul 32 et 64 bits

Prend en charge Hyp er Transport 3.0 et PowerNow

Initiatives de contrôle environnementales,

Mon iteur d e mat ériel
Contrôleur de vitesse de ventilateur
Fonction "Gardien intelligent" de l'ITE

Module d e mémo ire DD R2 à mod e à doub le vo ie
Prend en charge la DDR2 533 / 667 / 800

Prend en charge la DDR2 1066 (by AM2+ CPU)
Les DIMM à registres et DIMM avec code correct eurs
d'erreurs ne sont pas prises en charge

Onboard side port memory 64MB (TA790GX A2+)
Onboard side port memory 128MB (TA790GX 128M)

Mémoire vidéo partagée maximale de 512 Mo
Prise en charge DX10/UVD/HDCP
Prise en charge (Hyb r id) CrossFireX (by ATI dr iver)

Mode principale de Bus Ultra DMA 33 / 66 / 100 /
133

Prend en charge le mode PIO 0~4,

Taux de transfert jusqu'à 3 Go/s.
Co nfo rme à la s pécif icat ion SATA Vers ion 2.0

Prise en charge RAID 0,1,5,1+0

10 / 100 / 1000 Mb /s négociation auto matique

Half / Full duplex capab ility

Sortie aud io à 7.1 vo ies
Prise en charge de l'audio haute déf inition

Chaque co nnector prend en ch arg e 2 lecteurs de
disquettes

Chaque co nne ctor prend en ch arg e 1 Port
d'imprimante

54

Connecteur IDE x1

Connecteur SATA x6

Connecteur du panneau avant x1 Prend en charge les équipements du panneau avant
Connecteur A ud io du p anneau avant x 1 Prend en charge la fo nct ion aud io du panneau avant
Connecteur d' entrée CD x1 Prend en charge la fonction d'entrée aud io de CD

Connecteur de sortie S/PDIF x 1

Connecteur d' entrée S/PDIF x1

Embase de ventilateur UC x1

Embase de ventilateur système x2 Alimentation électrique du ventilateur système

Embase d'effacement CMOS x1

Connecteur USB x3

Port série x1
Connecteur d' aliment at ion x1

(24 broches)
Connecteur d' aliment at ion x 2
(4 broch es)

Clavier PS/2 x1
Souris PS/2 x1

E/S du
panneau

arrière

Dimensions
de la carte

Support SE Windows XP / VISTA

Port HD MI x1
Port VGA x1
Port DVI-D x1

Port LAN x1
Port USB x4

Fiche aud io x6

225 mm (l) X 305 mm (H) ATX

TA790GX A2+/TA790GX A2+ SE/TA790GX 128M

SPEC

Chaque connecteur prend en charge 2 périphériques
IDE

Chaque connecteur prend en ch arg e 1 périphérique
SATA

Prend en charge la fonction de sortie audio
numérique

Prend en charge la fonct ion d'entrée audio
numérique
Alimentation électrique du ventilateur UC (avec

fonction de ventilateur intelligent)

Chaque connecteur prend en charge 2 ports USB de
panneau avant

Biostar se réserve le droit d'ajouter ou de supprimer
le support de SE avec ou sans préavis.

55

Motherboard Manual

ITALIAN

Socket AM2+

CPU

FSB

Chipset

Super I/O

Memor ia

principale

Grafica Radeon HD 3300

IDE AMD SB750

SATA II AMD SB750

LAN Realtek RTL 8111C

Codec

audio

Allo g gi

Processori AMD Athlon 64 / Athlon 64

FX / Athlon 64 X2 / Sempron /

Pheno m

Supporto di HyperTransport 3.0 fino a

5.2 GT/s di larghezza di banda

AMD 790GX

AMD SB750

ITE 8718

Fo rnis ce le funzion al ità legacy Sup er

I/O usate più comunemente.

Interfaccia LPC (Low Pin Count)

Alloggi DIMM DDR2 x 4

Ciascun DIMM supporta DDR2

256MB/512MB/1GB/2GB/4GB

Capacità massima della memoria

16GB

ALC888

Allo g gio PC I x2

Alloggio PCI Express Gen2 x16 x2

Alloggio PCI Express Gen2 x1 x2

SPECIFICA

L’arch itet tura AMD 64 abilit a la co mput az io ne 32

e 64 bit

Supporto di Hyper Transport 3.0 e PowerNow

Funzioni di controllo dell’ambiente:

Monitoraggio hardware

Co ntroller v elo c it à vent o lina

Funzione "Smart Guardian" di ITE

Modulo di memoria DDR2 a canale doppio

Supporto di DDR2 533 / 667 / 800

Supporto di DDR2 1066 (by AM2+ CPU)

DIMM registrati e DIMM ECC non sono supportati

Onboard side port memory 64MB (TA790GX A2+)

Onboard side port memory 128MB (TA790GX 128M)

La memoria video condivisa massima è di 512 MB

Supporto DX10/UVD/HDCP

Supporto (Hybrid) CrossFireX (by ATI driver)

Modalità Bus Master Ultra DMA 33 / 66 / 100 /

133

Supporto modalità PIO Mode 0-4

Velocità di trasferimento dei dati fino a 3 Gb/s.

Co mp at ibile specif iche SATA Version e 2 .0 .

Supporto RAID 0,1,5,1+0

Negoziazione automatica 10 / 100 / 1000 Mb/s

Capacità Half / Full Duplex

Uscita audio 7.1 canali

Supporto audio High-Definition (HD)

56

Connettori

su scheda

I/O

pannello

posteriore

Dimension

i scheda

Sistemi

oper at ivi

supportati

TA790GX A2+/TA790GX A2+ SE/TA790GX 128M

SPECIFICA

Connettore floppy x1 Ciascun connettore supporta 2 unità Floppy

Connettore Porta stampante x1 Ciascun connettore supporta 1 Porta stampante

Connettore IDE x1 Ciascun connettore supporta 2 unità IDE

Connettore SATA x6 Ciascun connettore supporta 1 unità SATA

Co nnettor e p annello fron tale x1 Suppo rta i servizi del p an nel lo fr ont ale

Connettore audio frontale x1 Supporta la funzione audio pannello frontale

Connettore CD-in x1 Supporta la funzione input audio CD

Connettore output S/PDIF x1 Supporta la funzione d’output audio digitale

Connettore input S/PDIF x1 Supporta la funzione d’input audio digitale

Co llet t ore ven tolina C PU x 1

Co llet t ore ven tolina s is t em a x 2 A limentazione vento l ina d i s is tema

Co llet t ore can ce llaz ion e C MOS x1

Connettore USB x3

Porta seriale x1

Connettore alimentazione x1

(24 pin)

Connettore alimentazione x 2

(4 pin)

Tas t iera P S / 2 x 1

Mou s e PS /2 x1

Porta HDMI x1

Porta VGA x1

Porta DV I-D x1

Porta LA N x 1

Porta USB x4

Connettore audio x6

225 mm (larghezza) x 305 mm

(altez za)

Windows XP / VISTA

Alimentazione ventolina CPU (con funzione Smart

Fan)

Ciascun connettore supporta 2 porte USB

pannello frontale

ATX

Biostar si riserva il diritto di aggiungere o

rimuovere il supporto di qualsiasi sistema

operativo senza preavviso.

57

Motherboard Manual

SPANISH

Conector AM2+

CPU

FSB

Conjunto de

chips

Súper E/S

Memoria

principal

Gráficos Radeon HD 3300

IDE AMD SB750

SATA II AMD SB750

Red Local Realtek RTL 8111C

Códecs de

sonido

Ranuras

Procesadores AMD Athlon 64 / Athlon 64

FX / Athlon 64 X2 / Sempron / Pheno m

Admite HyperTransport 3.0 con un ancho

de banda de hasta 5.2 GT/s

AMD 790GX

AMD SB750

ITE 8718

Le ofrece las funcionalidades heredadas de

us o más comú n Súper E/S.

Interfaz de cuenta Low Pin

Ranuras DIMM DDR2 x 4

Cada DIMM admite DDR de

256MB/512MB/1GB/2GB/ 4GB

Capacidad máxima de memoria de 16GB

ALC888

Ranura PCI X2

Ranura PCI Express Gen2 x16 X2

Ranura PCI express Gen2 x1 X2

Especificación

La arquitectura AMD 64 permite el procesado de 32 y

64 bits

Soporta las tecnologías Hyper Transport 3.0 y

Power Now

In iciat iv as de cont rol d e ento rno ,

Monitor hardware

Controlador de velocidad de ventilador

Función "Guardia inteligente" de ITE

Módulo de memoria DDR2 de canal Doble

Admite DDR2 de 533 / 667 / 800

Admite DDR2 de 1066 (by AM2+ CPU)

No admite DIMM registrados o DIMM compatibles con

ECC

Onboard side port memory 64MB (TA790GX A2+)

Onboard side port memory 128MB (TA790GX 128M)

Memoria máxima de vídeo compartida de 512 MB

Admite DX10/UVD/HDCP

Admite (Hybr id) C ro ssFireX (by ATI dr iver)

Modo bus maestro Ultra DMA 33 / 66 / 100 / 133

Soporte los Modos PIO 0~4,

Tasas de transferencia de hasta 3 Gb/s.

Co mp at ible con la vers ión S ATA 2.0.

Admite RAID 0,1,5,1+0

Negociación de 10 / 100 / 1000 Mb/s

Funciones Half / Full dúplex

Salida de sonido de 7.1 canales

Soporte de sonido de Alta Definición

58

Conectores

en p laca

Panel

trasero de

E/S

Ta mañ o d e

la placa

Soporte de

sistema

operativo

TA790GX A2+/TA790GX A2+ SE/TA790GX 128M

Especificación

Conector disco flexible X1 Cada conector soporta 2 unid ades de disco flexible

Conector Puerto de impresora X1 Cada conector soporta 1 Puerto de impresora

Conector IDE X1 Cada conector soporta 2 dispositivos IDE

Conector SATA X6 Cada conector soporta 1 dispositivos SATA

Co nect o r de panel fro nta l X1 So port a instala ciones en e l p an e l fron tal

Conector de sonido frontal X1 Soporta funciones de sonido en el panel frontal

Conector de entrada de CD X1 Soporta función de entrada de sonido de CD

Conector de salida S/PDIF X1 Soporta función de salida de sonido digital

Conector de entrada S/PDIF x1 Soporta función de entrada de sonido d igital

Cabecera de ventilador de CPU X1 Fuente de alimentación de ventilador de CPU (con

función Smart Fan)

Cabecera de ventilador de sistema X2 Fuente de alimentación de ventilador de sistema

Cabecera de borrado de CMOS X1

Conector USB X3 Cada conector s oporta 2 puerto s USB frontales

Puert o ser ie X1

Conector de alimentación X1

(24 patillas)

Conector de alimentación X2

(4 patillas)

Tec lad o P S /2 X1

Ratón PS/2 X1

Puert o HDMI X1

Puert o VGA X1

Puerto DV I-D X1

Puerto de red local X1

Puert o USB X4

Conector de sonido X6

225 mm. (A) X 305 mm. (H) ATX

Windows XP / VISTA

Biostar se reserva el derecho de añadir o retirar el

soporte de cualquier SO con o sin aviso previo.

59

Motherboard Manual

PORTUGUESE

Socket AM2+

CPU

FSB

Chipset

Especificaçã

o Super I/O

Memória

principal

Placa

gráf ica

IDE AMD SB750

SATA II AMD SB750

LAN Realtek RTL 8111C

Codec de

som

Ranhuras

Processadores AMD Athlon 64 / Athlon 64

FX / Athlon 64 X2 / Sempron / Pheno m

Suporta a tecnologia HyperTransport 3.0

com u ma largura de band a até 5. 2 GT/s

AMD 790GX

AMD SB750

ITE 8718

Proporciona as funcionalidades mais

utilizadas em termos da especificação

Super I/O.

Interface LPC (Low Pin Count).

Ranhuras DIMM DDR2 x 4

Cada módulo DIMM suporta uma

memória DDR2 de 256 MB/512MB/

1GB/2GB/4GB

Capacidad e máx ima de me mória: 16GB

Radeon HD 3300

ALC888

Ranhura PCI x2

Ranhura PCI Express Gen2 x16 x2

Ranhura PCI Express Gen2 x1 x2

ESPECIFICAÇÕES

A arq uite ctura AMD 64 p ermite u ma co mputação de 32

e 64 bits

Suporta as tecno log ias Hyper Transport 3.0 e

Power Now

In iciat iv as par a con t ro lo d o amb ien te

Monitorização do hardware

Controlador da velocidade da ventoinha

Função "S mart Gu ard ian" d a ITE

Módulo de memória DDR2 de canal duplo

Suporta módulos DDR2 533 / 667 / 800

Suporta módulos DDR2 1066 (by AM2+ CPU)

Os módulos DIMM registados e os DIMM ECC não são

suportados

Onboard side port memory 64MB (TA790GX A2+)

Onboard side port memory 128MB (TA790GX 128M)

Memória de vídeo máxima partilhada: 512 MB

Suporta as funções DX10/UVD/ HDCP

Suporta as funções (Hybrid) CrossFireX (by ATI driver)

Modo Bus master U ltra DMA 33 / 66 / 100 / 133

Suporta o modo PIO 0~4,

Velocidades de transmissão de dados até 3 Gb/s.

Compat ibilidade com a es pe cificação SATA versão 2.0.

Suporta as funções RA ID 0,1,5,1+0

Auto negociação de 10 / 100 / 1000 Mb/s

Capacidade semi/full-duplex

Saída de áudio de 7.1 canais

Suporta a especificação High-Definition Audio

60

Conectores

na placa

Entradas/S

aídas no

painel

traseiro

Tamanho

da placa

Sistemas

operativos

suportados

TA790GX A2+/TA790GX A2+ SE/TA790GX 128M

ESPECIFICAÇÕES

Conector da unidade de disquetes x1 Cada conector suporta 2 unidades de d isquetes

Conector da para impressora x1 Cada conector suporta 1 Porta para impressora

Conector IDE x1 Cada conector suporta 2 dispositivos IDE

Conector SATA x6 Cada conector suporta 1 dispositivo SATA

Conector do painel frontal x1 Para suporte de várias funções no painel frontal

Conector de áudio frontal x 1 S uport a a função de áudio no paine l fronta l

Conector para entr ada de CDs x1 Supo rta a entrada d e áud io a p art ir de CDs

Conector d e saíd a S/PD IF x1 Suporta a s aída de áudio d ig ital

Conector de entrada S/PDIF x1 Suporta a entr ada d e áud io digit al

Conector da ventoinha da CPU x1

Conector da ventoinha do s istema x2 Alimentação da ventoinha do sistema

Conector para limpeza do CMOS x1

Conector USB x3 Cada conector suporta 2 portas USB no painel frontal

Porta série x1

Conector de alimentação x1

(24 pinos)

Conector de alimentação x2

(4 p inos )

Tec lad o P S /2 x 1

Rato PS/2 x1

Porta HD MI x 1

Porta VGA x1

Porta DV I-D x1

Porta LA N x1

Porta USB x4

Tomada de áudio x6

225 mm (L) X 305 mm (A) ATX

Windows XP / VISTA

Aliment ação da vento inh a da CP U (co m a fun ção S mart

Fan )

A Biostar reserva-se o direito de adicionar ou remover

suporte para qualquer sistema operativo com ou sem

av iso prév io .

61

Motherboard Manual

POLISH

Socket AM2+

Procesor

FSB

Chipset

Pamięć

główna

Grafika Radeon HD 3300

Super I/O

IDE AMD SB750

SATA II AMD SB750

LAN Realtek RTL 8111C

Kodek

dźwiękowy

Gniazda

AMD Athlon 64 / Athlon 64 FX / Athlon 64 X2 /

Sempron / Pheno m Proces ory

Obsługa HyperTransport 3.0 o szerokości pasma

do 5.2 GT/s

AMD 790GX

AMD SB750

Gniazda DDR2 DIMM x 4

Każde gniazdo DIMM obs ługuje moduły

256MB/512MB/1GB/2GB/4GB DDR2

Maks. wielkość pamięci 16GB

ITE 8718

Zapewnia najbardziej powszechne funkcje Super

I/O.

Interfejs Low Pin Count

ALC888

Gniazdo PCI x2

Gniazdo PCI Express Gen2 x16 x2

Gniazdo PCI Express Gen2 x1 x2

SPEC

Architektura AMD 64 umożliwia przetwarzanie

32 i 64 bitowe

Obsługa Hyper Transport 3.0 oraz PowerNow

Mod uł pamięci DDR2 z trybem podwójnego

kana łu

Obsługa DDR2 533 / 667 / 800

Obsługa DDR2 1066 (by AM2+ CPU)

Brak obsług i Regist ered D IMM oraz ECC DIMM

Onboard side port memory 64MB (TA790GX A2+)

Onboard side port memory 128MB (TA790GX 128M)

Maks. wielkość współdz ie lo n ej pami ęci video

wynosi 512 MB

Obsługa DX10/UVD/HDCP

Obsługa (Hybr id) CrossFireX (by ATI driver)

Funkcje kontroli warunków pracy,

Mon itor H /W

Kontroler prędkości wenty latora

Funkcja ITE "Smart Guard ian"

Ultra DMA 33 / 66 / 100 / 133 Tryb Bus Master

obsługa PIO tryb 0~4,

Transfer danych do 3 Gb/s.

Zgodność ze specyfikacją SATA w wersji 2.0.

Obsługa RAID 0,1,5,1+0

10 / 100 / 1000 Mb/s z automatyczn ą nego cjacją

szybkości

Działanie w trybie połowicznego/pełnego

dupleksu

7.1 kanałowe wyjście audio

Obsługa H igh- Def inition Aud io

62

Złącza

wbud owan e

Back Panel

I/O

Wymiary

płyty

Obsluga

systemu

operacyjne

go

TA790GX A2+/TA790GX A2+ SE/TA790GX 128M

SPEC

Złącze napędu dyskietek x1 Każde złącze obs ługuje 2 napędy dyskietek

Złącze Port drukarki x1 Każde złącze o bs ługuje 1 Port drukarki

Złącze IDE x1 Każde złącze obsługuje 2 urządzenia IDE

Złącze SATA x6 Każde złącze obs ługuje 1 urządzenie SATA

Złącze panela przedniego x1 Obsługa elementów panela przedniego

Przedn ie złącze audio x 1 Obsługa funkcj i audio na panelu przednim

Złącze wejścia CD x1 Obsługa funkcji wejścia aud io CD

Złącze wyjścia S/PDIF x1 Obsługa funkcji cyfrowego wyjścia aud io

Złącze wejścia S/PDIF x1 Obsługa funkcji cyfrowego wejścia aud io

Złącze głó wkow e wentylato ra

procesora x1

Złącze głó wkowe wentylatora systemowego x2 Zasilanie wentylatora systemowego

Złącze głó wkowe kasowania

CMOS x1

Złącze USB x3

Port sz eregowy x1

Złącze zasilania (24 pinowe) x1

Złącze zas ilania (4 p ino we) x2

Klawiatura PS/2 x1

Mys z PS /2 x 1

Port HD MI x1

Port VGA x1

Port DVI-D x1

Port LAN x1

Port USB x4

Gniazdo audio x6

225 mm (S) X 305 mm (W) ATX

Windows XP / VISTA

Zasilanie wentylatora procesora (z funkcją Smart

Fan )

Każde złącze obs ługuje 2 porty USB na panelu

przednim

Biostar zastrzega sobie prawo dodawania lub

odwoływ ania obsług i dowo ln ego sys temu

operacyjnego b ez powiado mienia.

63

Motherboard Manual

/

RUSSIAN

CPU

(центральн

ый

процессор)

FSB

Набо р
микросхем

Основная
память

Графика Radeon HD 3300

Super I/O

IDE AMD SB750

SATA II AMD SB750

Локальна я

сеть

Звуко вой
кодек

Слоты

Гнездо AM2+

Процессоры AMD Athlon 64 / Athlon 64 FX

Athlon 64 X2 / Sempron / Phenom

Поддержка HyperTransport 3.0 с
пропускной способностью до 5.2 GT/s

AMD 790GX
AMD SB750

Слоты DDR2 DIMM x 4
Каждый модуль DIMM поддерживает
256МБ /512МБ /1 ГБ /2 ГБ/4 ГБ DDR2

Максимальная ёмкость памяти 16ГБ

ITE 8718

Обеспечивает наиболее используемые

действующие фун кц ио наль ны е
возможно сти Super I/O.

Интерфейс с низ ким коли чест вом выводо в

Realtek RTL 8111C

ALC888

Слот PCI x2

Слот PCI Express Gen2 x16 x2
Слот PCI Express Gen2 x1 x2

СПЕЦ

Арх итектура AMD 64 разрешать обработка

данных на 32 и 64 бит
Поддержка Hyper Transport 3.0 и PowerNo w

Мод ул ь памяти с двухканальным режимом DDR2
Поддержка DDR2 533 / 667 / 800
Поддержка DDR2 1066 (b y AM2+ CPU)

Не поддерживает зарегистрированные модули

DIMM and ECC DIMM

Onboard side port memory 64MB (TA790GX A2+)
Onboard side port memory 128MB (TA790GX 128M)

Максимальная совместно использ уемая вид ео

память составляет 512 МБ
Поддержка DX10/UVD /HDC P

Поддержка ( Hybr id) CrossFir eX (b y AT I dr iver)

Инициативы по охране окружающей среды,
Аппаратный монитор

Регул ятор скорости
Функция ITE "Smart Gu ard ian "

(Интеллектуальная защита)

Режим "хозяина" шины U ltra DMA 33 / 6 6 / 1 00 /

133

Поддержка режима PIO 0~4,

скорость передачи данных до 3 гигабит/с.

Соответствие спецификации SATA версия 2.0.
Поддержка RAID 0,1,5,1+0

Автоматическо е согласование 10 / 100 / 1000

Мб/с
Частичная / полна я дуплексная способность

Звуко вая поддержка H igh- Def in ition

7.1канальный звуковой выход

64

Встроенны
й разъём

Задняя
панель

средств
ввода-выв

ода

Разм ер
панели

Поддержка

OS

TA790GX A2+/TA790GX A2+ SE/TA790GX 128M

СПЕЦ

Разъ ём НГМД x1

Разъ ём Порт подключения
принтера x1

Разъ ём IDE x 1

Разъ ём SATA x6 Каждый разъём поддерживает 1 устро йство SATA

Разъ ём на лицевой панели x1 Поддержка устройств на лицевой панели

Входной звуковой разъём x1

Разъ ём ввода для CD x1 Поддержка функции ввод а для CD
Разъ ём вывод а для S/PDIF x1 Поддержка вывода цифровой звуковой функц ии

Разъ ём ввода для S/PDIF x1 Поддержка ввод а цифровой звуково й функции

Контактирующее приспособление

вентил ятора центрального процессора x1

Контактирующее приспособление

вентил ятора системы x2
Открытое контактирующее

приспособление CMOS x1

USB- разъём x3

Последо ват ельный порт x1
Разъ ем питания (24 вы вод ) x1

Разъ ем питания (4 выво д) x2

Клавиатура PS/2 x1
Мышь PS/2 x1

Пор т HD MI x 1
Пор т VGA x1

Пор т DVI-D x1
Пор т LAN x1
USB- порт x4

Гнездо для подключени я
наушников x6

225 мм (Ш) X 305 мм (В) ATX

Windows XP / VISTA

Каждый разъём поддерживает 2 накопителя на
гибких магнитных дисках

Каждый разъём поддерживает 1 По рт
подключения принтера

Каждый разъём поддерживает 2 встроенных
интерфейса накопителей

Поддержка звуко вых функций на лицевой

панели

Источник питания для вентилятор а центрального

процессора (с функц ией интеллектуального
вентил ятора)

Источник пит ания для вентил ятора системы

Каждый разъём поддерживает 2 USB-порта на
лицевой панели

Biostar сохраняет за собой право добавлять или

удаля ть средства обеспечения для OS с или без
предварительного уведом ле ния .

65

Motherboard Manual

ARABIC

ﺔﻴﻨﻘﺗ ﻦﻜﻤﺗAMD 64 ﺔﻋﺮﺴﺏ ﺔﻴﺏﻮ ﺳﺎﺤﻟا تﺎﻴﻠﻤﻌﻟا ءاﺮﺝإ 32 و64 ﺏﺖ

ﺔﻴﻨﻘ ﺗ ﻢﻋﺪﺗHyper Transport و 3.0 PowerNow

ةﺪﺣو ةﺮآاذ DDR2 ﺔﺝودﺰﻡ ةﺎﻨﻘﻟا

ﻢﻋﺪﺗ ةﺮآاﺬﻟا ﻦﻡ عﻮﻥ DDR2 تﺎﻌﺳ 800/667/533 ﺎﺠﻴﻡ ﺖﻳﺎﺏ

ﻢﻋﺪﺗ ةﺮآاﺬﻟا ﻦﻡ عﻮﻥ DDR2 تﺎﻌﺳ 1066(By AM2+ CPU)

ﻻ ﻢﻋﺪﺗ ﻖﺋﺎﻗر ةﺮآاﺬﻟا DIMM ﻠﺗوﻚ ﻲﺘﻟا ﻻ ﻖﻓاﻮﺘﺗ ﻊﻡ ECC

Onboard side port memory 64MB(TA790GX A2+)

Onboard side port memory 128MB(TA790GX 128M)

ﻰﺼﻗأ ﺔﻌﺳ ةﺮآاﺬﻟ ﻮﻳﺪﻴﻔﻟا ﺔآﺮﺘﺸﻤﻟا 512 ﺎﺠﻴﻣ ﺖﻳﺎﺑ

ﺔﻴﻨﻘ ﺗ ﻢﻋﺪﺗHDCP/UVD/DX10

ﺔﻴﻨﻘ ﺗ ﻢﻋﺪﺗ(Hybrid ) CrossFireX (by ATI driver)

ﺔﺌﻴﺒﻟا ﻲﻓ ﻢﻜﺤﺘﻟا ﻞﺋﺎﺳو:

ةﺰﻬﺝﻷا ﺔﻟﺎﺣ ﺔﻓﺮﻌﻤﻟ ﺐﻗاﺮﻡ

ﺔﺣوﺮﻤﻟا ﺔﻋﺮﺳ ﻲﻓ ﺐﻗاﺮﻡ

ﺔﻔﻴﻇو"S mart Guardian" ﻦﻡ IT E

ﺔﻴﻨﻘ ﺘﺏ ﻞﻗﺎﻥUltra DMA 33 / 66 / 100 / 133

ﻲﺴﻴﺋر ﻊﺿو

ﻊﺿو ﻢﻋدPIO Mode 0~4

ﻰﻟإ ﻞﺼﺗ تﺎﻋﺮﺴﺏ تﺎ ﻥﺎﻴﺒﻟا ﻞﻘﻥ3 ﺖﺏﺎﺠﻴﺝ/ﺔﻴﻥﺎ ﺙ.

تﺎﻔﺹاﻮﻤﻟ ﺔﻘﺏﺎﻄﻡSATA راﺪﺹﻹا 2.0.

ﺔﻴﻨﻘ ﺗ ﻢﻋﺪﺗRAID 0,1,5,1+0

ﻦﻡ ﻒﻳﺮﻌﺘﻟا ﻲﻟ ﺎﻋ تﻮﺼﻟا ﺔﻴﻨﻘﺗ ﻢﻋﺪﺗ

66

تﺎﻔﺻاﻮﻤﻟا

تﺎﺠﻟﺎﻌﻡAMD Athlon 64 / Athlon 64 FX / Athlon 64

X2 / S empron / Ph enom

ﺔﻴﻨﻘ ﺗ ﻢﻋﺪﺗHyperTransport ﻰﻟإ ﻞﺼﻳ ددﺮﺘﺏ 3.0 5.2 GT/s

DIMM ﻢﻋﺪﺗ ةﺮآاذ ﻦﻡ عﻮﻥ DDR2 ﺔﻌﺳ

ﺔﺤﺘﻓ ﻞآ ﻢﻋﺪﺗDIMM ذ ﻢﻋﺪﺗ عﻮﻥ ﻦﻡ ةﺮآا DDR2 ﺔﻌﺳ 256/512 ﺎﺠﻴﻡ

ﺎﺠﻴﻡ ﺖﻳﺎﺏ

Radeon HD 3300

ﺔﻔﻴﻇ و ﺮﻓﻮﺗSuper I/O ًﺎ ﻡ ا ﺪ ﺨ ﺘﺳا ﺮﺜآﻷا .

ﺗﻢﻋﺪ ﺔﻴﻨﻘ ﺗ Low Pi n Count Interface

ضوﺎﻔﺕ ﻲﺋ ﺎﻘﻠﺕ 10/100 ﺎﺠﻴﻣ ﺖﻳﺎﺑ /ﺔﻴﻧﺎﺛ و1ﺎﺠ ﻴﺝ ﺖﺑ/ﺔﻴﻧﺎﺛ

ﺎﻜﻣإﺔﻴ ﻧ ﻞﻘﻨﻟ ا جودﺰﻤﻟا ﻞﻣﺎﻜﻟا/ﻲﻔﺼﻨﻟا

7.1 تﻮﺼﻟا جﺮﺨﻟ تاﻮﻨﻗ

Realtek RTL 8111C

ﺲﺒﻘﻡAM2+

AMD 790GX

AMD SB750

ﺔﺤﺘﻓ DDR2 DIMM دﺪﻋ4

و ﺖﻳﺎﺏ1/و 2/و 4 ﺎﺠﻴﺝﺖﻳﺎﺏ ﺔﻌﺳ ةﺮآاذ ىﻮﺼﻗ 16 ﺎﺠﻴﺝ ﺖﻳﺎﺏ

ITE 8718

AMD SB750

AMD SB750

ALC888

ﺔﺤﺘﻓPCI ﺪﻋ2

ﺔﺤﺘﻓGen2 x16 PCI Express دﺪﻋ2

ﺔﺤﺘﻓPCI Express Gen2 x1 دﺪﻋ2

ﺔﺠﻟﺎﻌﻤﻟا ةﺪﺣو

ﺔﻳﺰآﺮﻤﻟا

ﻲﺒﻥﺎﺠﻟا ﻲﻡﺎﻡﻷا ﻞﻗﺎﻨﻟا

ﺢﺋاﺮﺸﻟا ﺔﻋﻮﻤﺠﻡ

ﺔﻴﺴﻴ ﺋﺮﻟا ةﺮآاﺬﻟا

ﺔﻗﺎﻄﺑ تﺎﻣﻮﺳﺮﻟا

Super I/O

ﺬﻔﻨﻡIDE

SATA II

ﺔﻴﻠﺥاد ﺔﻜﺒﺵ

تﻮﺼﻟا ﻚﻳدﻮآ

تﺎﺤﺘﻔﻟا

ﻆﻔﺘﺤﺗBiostar ﻲﻓ ﺎﻬﻘﺤﺏ وأ رﺎﻄﺥﺈﺏ ﻞﻴﻐﺸﺗ مﺎﻈﻥ يﻷ ﻢﻋﺪﻟا ﺔﻟازإ وأ ﺔﻓﺎﺿ إ

TA790GX A2+/TA790GX A2+ SE/TA790GX 128M

تﺎﻔﺻاﻮﻤﻟا

ﺔﻥﺮﻡ صاﺮﻗأ كﺮﺤﻡ ﺬﻔﻨﻡ دﺪﻋ1 ﻡ ﻢﻋﺪﻳﺔﻥﺮﻤﻟا صاﺮﻗﻸﻟ ﻦﻴآﺮﺤ

ﺔﻌﺏﺎﻃ ﺬﻔﻨﻡ دﺪﻋ1

ﺬﻔﻨﻡIDE دﺪﻋ1 ةﺰﻬﺝأ ﻦﻡ ﻦﻴﻨﺙا ﺬﻔﻨﻡ ﻞآ ﻢﻋﺪﻳIDE

ﺬﻔﻨﻡSATA دﺪﻋ6 ةﺰﻬﺝأ ﻦﻡ ﺪﺣاو ﺬﻔﻨﻡ ﻞآ ﻢﻋﺪﻳSATA

ﺔﻴﻡﺎﻡﻷا ﺔﺣﻮ ﻠﻟا ﺬﻔﻨﻡ دﺪﻋ1 ﺔﻴﻡﺎﻡﻷا ﺔﺣﻮﻠﻟا تاﺰﻴﻬﺠﺗ ﻢﻋﺪﻳ

ﻲﻡﺎﻡﻷا تﻮﺼﻟا ﺬﻔﻨﻡ دﺪﻋ1 ﻴﻡﺎﻡ ﻷا ﺔﺣﻮﻠﻟ ﺎﺏ تﻮﺼﻟا ﺔﻔﻴﻇو ﻢﻋﺪﻳﺔ

ﺬﻔﻨﻡCD-IN دﺪﻋ1 ﺞﻡﺪﻤﻟا صﺮﻘﻟا تﻮﺹ ﻞﺥد ﺔﻔﻴﻇو ﻢﻋﺪﻳ

جﺮﺥ ﺬﻔﻨﻡS/PDIF دﺪﻋ1 ﻲﻤﻗﺮﻟا تﻮﺼﻟا جﺮﺥ ﺔﻔﻴﻇو ﻢﻋﺪﻳ

ﻞﺥد ﺬﻔﻨﻡS/PDIF دﺪﻋ1 ﻲﻤﻗﺮﻟا تﻮﺼﻟا ﻞﺥد ﺔﻔﻴﻇو ﻢﻋﺪﻳ

ﺔﻳﺰآﺮﻤﻟا ﺔﺠﻟﺎﻌﻤﻟا ةﺪﺣو ﺔﺣوﺮﻡ ﺔﻠﺹو دﺪﻋ1 ﺔﻔﻴﻇو ﻊﻡ ﺔﺠﻟﺎﻌﻤﻟا ةﺪﺣو ﺔﺣوﺮﻤﻟ ﺔﻗﺎﻄ ﻟا ﻞﻴﺹﻮﺘﻟSmart Fan

ﺢﺴﻡ ﺔﻠﺹوCMOS دﺪﻋ1

ﻲﻠﺴﻠﺴﺗ ﺬﻔ ﻨﻡ دﺪﻋ1

ﺔﻗﺎﻄﻟا ﻞﻴﺹﻮﺗ ﺬﻔﻨﻡ)24سﻮﺏد( دﺪﻋ1

ﺔﻗﺎﻄﻟا ﻞﻴﺹﻮﺗ ﺬﻔﻨﻡ)4ﺲﻴﺏﺎﺏد( دﺪﻋ2

ﺔﻴﻠﺤﻡ لﺎﺼﺗا ﺔﻜﺒﺵ ﺬﻔﻨﻡ ﺪﻋ1

تﻮﺹ ﺲﺒﻘﻡ دﺪﻋ6

رﺎﻄﺥإ نوﺪﺏ.

Windows XP / VISTA

ﺢﻄ ﺳ ﻰﻠﻋ ﺬﻓﺎﻨﻤﻟا

ومﺎﻈﻨﻟا ﺔﺣوﺮﻡ ﺔﻠﺹ ﺪﻋ2 مﺎﻈﻨﻟا ﺔﺣوﺮﻤﻟ ﺔﻗﺎﻄﻟا ﻞﻴﺹﻮﺘﻟ

ﺬﻔﻨﻡUS B دﺪﻋ3 ﻲﺘﺤ ﺘﻓ ﺬﻔﻨﻡ ﻞآ ﻢﻋﺪﻳUSBﺔﻴﻡﺎﻡﻷا ﺔﺣﻮﻠﻟﺎﺏ

ﻮﻟ ﺢﻴﺗﺎﻔﻡ ﺔﺣPS/2 دﺪﻋ1

سوﺎﻡ PS/2 دﺪﻋ1

ﺬﻓﺎﻨﻡHDM I دﺪﻋ1

ﺬﻓﺎﻨﻡVGA دﺪﻋ1

ﺬﻓﺎﻨﻡDV I-D دﺪﻋ1

ﻞﺥد ﺬﻓﺎﻨﻡ/ جﺮﺥ

ﺔﻴﻔﻠﺨﻟا ﺔﺣﻮﻠﻟا

ﺬﻓﺎﻨﻡUS B دﺪﻋ4

225 ﻢﻡ)ضﺮﻋ (X 305 ﻢﻡ)عﺎﻔﺗرا( AT X

ﺔﺣﻮﻠﻟا ﻢﺠﺣ

ﻞﻴﻐﺸﺘﻟا ﺔﻤﻈﻥأ ﻢﻋد

ﺔﺣﻮﻠﻟا

67

Motherboard Manual

/

JAPANESE

Socket AM2+

CPU

FSB

チップセット

メインメモリ

グラフィック

ス

Super I/O

IDE AMD SB750

SATA II AMD SB750

LAN Realtek RTL 8111C

サウンド

Codec

スロット

68

AMD Athlon 64 / Athlon 64 FX

/ Sempron / Phenom プロ セッ サ

5.2 GT/sのバンド 幅まで ハイパート ランスポー ト

3.0をサポート します

AMD 790GX

AMD SB750

DDR2 DIMMスロット x 4

各DIMMは 256 MB/512 MB/1GB/2GB /4GB

DDR2をサポート

最大メモリ容 量16GB

Radeon HD 3300

ITE 8718

もっとも一般 に使 用されるレ ガシーSuper I/O機

能を採用して いま す。

低ピンカウン トイ ンターフェ イス

ALC888

PCIスロット x2

PCI Express Gen2 x16スロット x2

PCI Express Gen2 x1スロ ット x2

仕様

Athlon 64 X2

AMD 64アーキ テクチャで は、32ビットと64ビット計算が

可能です

ハイパートラ ンス ポート3.0と クールアン ドクワイア ット

をサポートし ます

デュアル チ ャン ネルモードDDR2メモリモジ ュール

DDR2 533 / 667 / 800をサポー ト

DDR2 1066をサ ポート (by AM2+ CPU)

登録済みDIMMとECC DIMMはサポ ートされま せん

Onboard side port memory 64MB (TA790GX A2+)

Onboard side port memory 128MB (TA790GX 128M)

最大の共有ビ デオ メモリは512MBです

DX10/UVD/HDCP のサポート

(Hybrid) CrossFireX のサ ポート(by ATI dr iver)

環境コントロ ール イニシアチ ブ、

H/Wモニター

ファン速度コ ント ローラ/ モニター

ITE の「スマート ガー ディアン」 機能

Ultra DMA 33 / 66 / 100 / 133バスマ スタモード

PIO Mode 0~4のサポート 、

最高3 Gb/秒の データ転送 速度

SATAバージョン2.0仕様に準拠。

RAID 0,1,5,1+0のサポート

10 / 100 / 1000 Mb/秒のオート ネゴシ エーション

半/全二重機能

ハイデフィニ ショ ンオーディ オのサポー ト

7.1 チ ャンネルオ ーディ オアウト

TA790GX A2+/TA790GX A2+ SE/TA790GX 128M

仕様

フロッピーコ ネク タ x1 各コネクタは 2つのフロ ッピードラ イブをサポ ートし ます

プリンタポー トコ ネクタ x1 各コネクタは 1つのプリンタポ ート をサポート します

IDE コネクタ x1 各コネクタは 2つのIDE デバイスをサポ ートします

SATAコネクタ x6 各コネクタは 1つのSATAデバイスをサポ ート します

フロントパネ ルコ ネクタ x1 フロントパネ ル機能をサ ポートしま す

フロントオー ディ オコネクタ x1 フロントパネルオ ーディ オ機能をサ ポー トします

CDインコネクタ x1 CDオーディオイ ン機能をサ ポートしま す

オンボードコ

ネクタ

背面パネル

I/O

ボードサイズ 225 mm (幅) X 305 mm (高さ) ATX

OSサポー ト Windows XP / VISTA

S/PDIFアウトコネ クタ x1 デジタルオー ディ オアウト機 能をサ ポートしま す

S/PDIFインコネク タ x1 デジタ ルオーディ オイン機能 をサポ ートします

CPUファンヘッダ x1 CPUファン電源装置(スマ ートファン 機能を搭載 )

システムファ ンヘ ッダ x2 システムファ ン電源装置

CMOSクリアヘッダ x1

USBコネク タ x3

シリアルポー ト x1

電源コネクタ (24 ピン) x1

電源コネクタ (4ピン) x2

PS/2キーボード x1

PS/2マウス x1

HDMIポート x1

VGAポート x1

DVI-Dポート x1

LANポート x1

USBポート x4

オーディオジ ャッ ク x6

各コネクタは 2つのフロ ントパネル USBポートをサ ポート

します

Biostarは事前の サポートな しにOSサ ポー トを追加ま たは

削除する権利 を留 保します。

2008/08/05

69