Biostar G31-M4 Owner's Manual

G31-M4 Setup Manual

FCC Information and Copyright

This equipment has been tested and found to comply with the limits of a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. There is no guarantee
that interference will not occur in a particular installation.

The vendor makes no representations or warranties with respect to the
contents here and specially disclaims any implied warranties of merchantability
or fitness for any purpose. Further the vendor reserves the right to revise this
publication and to make changes to the contents here without obligation to
notify any party beforehand.

Duplication of this publication, in part or in whole, is not allowed without first
obtaining the vendor’s approval in writing.

The content of this user’s manual is subject to be changed without notice and
we will not be responsible for any mistakes found in this user’s manual. All the
brand and product names are trademarks of their respective companies.

Table of Contents

Chapter 1: Introduction ............................................................ 1

1.1 Before You Start ................................................................................ 1

1.2 Package Checklist............................................................................. 1

1.3 Motherboard Features...................................................................... 2

1.4 Rear Panel Connectors ..................................................................... 3

1.5 Motherboard Layout......................................................................... 4

Chapter 2: Hardware Installation ............................................. 5

2.1 Installing Central Processing Unit (CPU)....................................... 5

2.2 FAN Headers...................................................................................... 6

2.3 Installing System Memory ................................................................ 7

2.4 Connectors and Slots......................................................................... 9

Chapter 3: Headers & Jumpers Setup ..................................... 12

3.1 How to Setup Jumpers .................................................................... 12

3.2 Detail Settings.................................................................................. 12

Chapter 4: Useful Help ............................................................ 16

4.1 Driver Installation Note.................................................................. 16

4.2 Software ............................................................................................ 17

4.3 Extra Information............................................................................ 21

4.4 AMI BIOS Beep Code....................................................................... 23

4.5 Troubleshooting............................................................................... 24

Appendix: SPEC In Other Languages ...................................... 25

German.................................................................................................................. 26

French .................................................................................................................... 28

Italian..................................................................................................................... 30

Spanish ................................................................................................................... 32

Portugue se ............................................................................................................ 34

Polish...................................................................................................................... 36

Russian ................................................................................................................... 38

Arabic..................................................................................................................... 40

Japanese ................................................................................................................ 42

CHAPTER 1: INTRODUCTION

G31-M4

1.1 B

EFORE YOU START

Thank you for choosing our product. Before you start installing the
motherboard, please make sure you follow the instructions below:

 Prepare a dry and stable working environment with

sufficient lighting.

 Always disconnect the computer from power outlet

before operation.

 Before you take the motherboard out from anti-static

bag, ground yourself properly by touching any safely
grounded appliance, or use grounded wrist strap to
remove the static charge.

 Avoid touching the components on motherboard or the

rear side of the board unless necessary. Hold the board
on the edge, do not try to bend or flex the board.

 Do not leave any unfastened small parts inside the

case after installation. Loose parts will cause short
circuits which may damage the equipment.

 Keep the computer from dangerous area, such as heat

source, humid air and water.

 The operating temperatures of the computer should be

0 to 45 degrees Celsius.

1.2 PACKAGE CHECKLIST

HDD Cable X 1 (optional)
Serial ATA Cable X 2
Rear I/O Panel for ATX Case X 1
Installation Guide X 1
Fully Setup Driver CD X 1 (full version manual files inside)
FDD Cable X 1 (optional)
USB 2.0 Cable X1 (optional)
Serial ATA Power Cable X 1 (optional)

Note: The package contents may be different due to area or your motherboard version.

1

Motherboard Manual

1.3 MOTHERBOARD FEATURES

SPEC

Socket 478

CPU

FSB Support 800 / 533 MHz

Chipset

Super I/O

Main

Memory

Graphics GMA 3100 Max Shared Video Memory is 256MB

IDE Integrat ed IDE Cont ro ller

SATA 2 Integrated Serial ATA Controller

LAN Realtek RTL 8102EL

Sound

Codec

Slots

On Board

Connector

Intel Pent ium4 /Celeron D / Celero n 3xx

processors (Maximum Watt: 95W)

Intel G31

Int e l ICH7

ITE 8721

Prov ides the mos t commonly us ed legacy

Super I/O functionality.

Low Pin Count Interface

DIMM Slots x 2

Each DIMM supports 256MB / 512MB /

1GB / 2GB DDR2

Max Memory Capacity 4GB

ALC662

PCI slot x2 Supports PCI expansion cards

PCI Express x 16 slot x1 Supports PCI-E x16 expansion card

Floppy Connector x1 Each connector supports 2 Floppy drives

Printer Port Connector x1 Each connector supports 1 Printer port

Serial Port Connector x1 Connects to RS-232 Port

IDE Conn ecto r x1 Each connector supports 2 IDE device

Supports Hyper-Threading / Execute Disable Bit /

Enhanced Inte l SpeedStep® / Int el Arch itecture-64 /

Extended Memory 64 Technology

En viro nment C o ntrol in itiat ives,

Hardware Monitor Controller

Dual Channe l Mode DDR 2 me mory mo dule

Supports DDR2 533/667/800

Register ed DIMM and ECC D IMM is not supported

(CPU with FSB 533 MHz only supports DDR2 533)

(CPU with FSB 800 MHz only supports DDR2 667/800)

Ultra DMA 33 / 66 / 100 Bus Master Mode

supports PIO Mode 0~4

Data transfer rates up to 3.0 Gb/s.

SATA Version 2.0 spe c if icat ion co mpl iant

10 / 100 Mb/s auto negot iation

Half / Full duplex capability

5.1 channels audio out

High Definition Audio

2

SPEC

SATA Connector x4 Each connector suppo rts 1 S ATA devices

Front Panel Connector x1 Supports front panel facilities

Front Audio Connector x1 Supports front panel audio function

CPU Fan Header x1 CPU Fan power supply

System Fan Header x1 System Fan Power supply

Clear CMOS Head er x1 Res tore CMOS data to fact ory def ault

USB Connector x2 Each connector supports 2 front panel USB ports

Power Connector (24pin) x1 Connects to Power supp ly

Power Connector (4pin) x1 Connects to Power supply

PS/2 Keybo ard x1

PS/2 Mous e x1

Back Panel

I/O

Board Size 200 (W) x 235 (L) mm

OS Support Windows 2000 / XP / Vista / 7

VGA port x1

LAN port x1

USB Port x4

Audio Jack x3

G31-M4

Connects to PS/2 Keyboard

Connects to PS/2 Mouse

Connect to D-SUB monitor

Connect to RJ-45 ethernet cab le

Connect t o USB devices

Provide Audio-In/Out and microphone connection

Biostar reserves the right to add or remove support for

any OS with or without notice

1.4 R

PS/ 2
Mouse

PS/2
Keyboard

Since the audio chip supports High Definition Audio Specification, the function of each audio
jack can be defined by software. The input / output function of each audio jack listed above
represents the default setting. However, when connecting external microphone to the audio port,
please use the Line In (blue) and Mic In (Pink) audio jack.

EAR PANEL CONNECTORS

VGA

USBX2USBX2

LAN

Line In/
Surround

Line Out

Mic In 1/
Bass/ Center

3

Motherboard Manual

1.5 MOTHERBOARD LAYOUT

KBMS1

ATXPWR2

VGA1

USB2

RJ45USB1

AUDIO1

Supe r

F_AUDIOF1

LAN

I/O

Codec

BIOS

JPRNT1

Socket 478

PEX16_1

PCI1

PCI2

JCOM1

FD D1

Intel

G31

JCMOS1

F_US B1 F_ USB2

CPU_FAN1

Intel

ICH7

SYS_FAN 1

ATX P WR 1

DDR 2_ B1

DDR 2_ A1

ID E1

BAT1

SATA4

SATA3

SATA2

SATA1

PANEL1

Note: ■ represents the 1st pin.

4

CHAPTER 2: HARDWARE INSTALLATION

G31-M4

2.1 I

NSTALLING CENTRAL PROCESSING UNIT (CPU)

Step 1: Pull the lever sideways away from the socket and then raise the

lever up to a 90-degree angle.

Step 2: Look for the white dot/cut edge. The white dot/cut edge should

point wards the lever pivot. The CPU will fit only in the correct
orientation.

Step 3: Hold the CPU down firmly, and then close the lever to complete

the installation.

Step 4: Put the CPU Fan on the CPU and buckle it. Connect the CPU FAN

power cable to the CPU_FAN1. This completes the installation.

5

Motherboard Manual

2.2 FAN HEADERS

These fan headers support cooling-fans built in the computer. The fan
cable and connector may be different according to the fan manufact urer.
Connect the fan cable to the connector while matching the black wire to
pin#1.

CPU_FAN1: CPU Fan Header

3

1

SYS_FAN1: System Fan Header

13

Pin

Assignment

1 Ground
2 Power
3 FAN RPM rate sense

Pin

Assignment

1 Ground
2 +12V
3 FAN RPM rate sense

Note:

The CPU_FAN1 support 4-pin head connector a nd SYS_FAN1 support 3-pin head
connector. When connecting with wires onto connectors, please note that the red wire is
the positive and should be connected to pin#2, and the black wire is Ground and should
be connected to GND.

6

2.3 INSTALLING SYSTEM MEMORY

A. DDR2 module

G31-M4

DDR2_B1

DDR2_A1

1. Unlock a DIMM slot by pressing the retaining clips outward. Align a
DIMM on the slot such that the notch on the DIMM matches the
break on the Slot.

2. Insert the DIMM vertically and firmly into the slot until the retaining
chip snap back in place and the DIMM is properly seated.

7

Motherboard Manual

B. Memory Capacity

DIMM Socket

Location

DDR2_A1 256MB/512MB/1GB/2GB

DDR2_B1 256MB/512MB/1GB/2GB

DDR2 Module

Total Mem ory

Size

Max is 4GB.

C. Dual Channel Memory Installation

Please refer to the following requirements to activate Dual Channel
function:

Install memory module of the same density in pairs, shown in the
table.

Dual Channel Status

Disabled O X

Disabled X O

Enabled O O

(O means memory installed, X means memory not installed.)

The DRAM bus width of the memory module must be the same(x8 or
x16)

DDR2_A1

DDR2_B1

8

2.4 CONNECTORS AND SLOTS

FDD1: Floppy Disk Connector

The motherboard provides a standard floppy disk connector that supports 360K,
720K, 1.2M, 1.44M and 2.88M floppy disk types. This connector supports the
provided floppy drive ribbon cables.

234

G31-M4

133

IDE1: Hard Disk Connector

The motherboard has a 32-bit Enhanced PCI IDE Controller that provides PIO
Mode 0~4, Bus Master, and Ultra DMA 33/66/100 functionality.

The IDE connector can connect a master and a slave drive, so you can connect
up to two hard disk drives.

40

2

39

1

9

Motherboard Manual

2

3

ATXP W R1: ATX Power Source Connector

This connector allows user to connect 24-pin power connector on the ATX
power supply.

12

1

Pin Assignment Pin Assignment

13 +3.3V 1 +3.3V
14 -12V 2 +3.3V
15 Ground 3 Ground
16 PS_ON 4 +5V
17 Ground 5 Ground
18 Ground 6 +5V
19 Ground 7 Ground
20 NC 8 PW_OK
21 +5V 9 Standby Voltage+5V
22 +5V 10 +12V
23 +5V 11 +12V
24 Ground 12 +3.3V

ATXP W R2: ATX Power Source Connector

This connector provides +12V to CPU power circuit.

24

13

1

4

Pin

Assignment

1 +12V
2 +12V
3 Ground
4 Ground

Note:

Before power on the system, please make sure that both ATXPWR1 and ATXPWR2
connectors have been plugged-in.

10

PEX16_1: PCI-Express x16 Slot

- PCI-Express 1.0a compliant.

- Maximum theoretical realized bandwidth of 4GB/s simultaneously per

direction, for an aggregate of 8GB/s totally.

- PCI-Express supports a raw bit-rate of 2.5Gb/s on the data pins.

- 2X bandwidth over the traditional PCI architecture.

PCI1/PCI2: Peripheral Component Interconnect Slots

This motherboard is equipped with 2 standard PCI slots. PCI stands for
Peripheral Component Interconnect, and it is a bus standard for expansion
cards. This PCI slot is designated as 32 bits.

G31-M4

PEX16_1

PCI1

PCI2

11

Motherboard Manual

CHAPTER 3: HEADERS & JUMPERS SETUP

3.1 H

OW TO SETUP JUMPERS

The illustration shows how to set up jumpers. When the jumper cap is
placed on pins, the jumper is “close”, if not, that means the jumper is
“open”.

Pin opened Pin closed Pin1-2 closed

3.2 DETAIL SETTINGS

PANEL1: Front Panel Header

This 16-pin connector includes Power-on, Reset, HDD LED, Power LED, and
speaker connection. It allows user to connect the PC case’s front panel switch
functions.

PWR_LED

On/Off

-

SPK

++

-

+

HLED

16

8

RST

9

1

12

Pin Assignment Function Pin Assignment Function

1 +5V 9 N/A

2 N/A 10 N/A

3 N/ A 11 N/ A N/A

4 Speaker

5 HDD LED (+) 13 Power LED (+)

6 HDD LED (-)

7 Ground 15 Power button

8 Reset control

Speaker
Connector

Hard drive
LED

Reset button

12 Power LED (+)

14 Power LED (-)

16 Ground

N/A

Power LED

Power-on button

G31-M4

F_USB1/F_USB2: Headers for USB 2.0 Ports at Front Panel

This motherboard provides 2 USB 2.0 headers, which allows user to connect
additional USB cable on the PC front panel, and also can be connected with
internal USB devices, like USB card reader.

F_USB1 F_USB2

210

Pin Assignment

1 +5V (fused)
2 +5V (fused)
3 USB­4 USB­5 USB+
6 USB+
7 Ground
8 Ground
9 Key

10 NC

F_AUDIOF1: Front Panel Audio Header

This header allows user to connect the front audio output cable with the PC front
panel. This header allows only HD audio front panel connector; AC’97 connector
is not acceptable.

19

10

9

1

2

Pin Assignment

1 Mic Left in
2 Ground
3 Mic Right in
4 GPIO
5 Right line in
6 Jack Sense
7 Front Sense
8 Key
9 Left line in

10 Jack Sense

13

Motherboard Manual

JCMOS1: Clear CMOS Header

By placing the jumper on pin2-3, it allows user to restore the BIOS safe setting
and the CMOS data, please carefully follow the procedures to avoid damaging
the motherboard.

※ Clear CMOS Procedures:

1. Remove AC power line.

2. Set the jumper to “Pin 2-3 close”.

3. Wait for five seconds.

4. Set the jumper to “Pin 1-2 close”.

5. Power on the AC.

6. Reset your desired password or clear the CMOS data.

SATA1~SATA4: Serial ATA Connectors

The motherboard has a PCI to SATA Controller with 4channels SATA interface, it
satisfies the SATA 2.0 spec and with transfer rate of 3Gb/s.

1

3

SATA4
SATA3
SATA2

SATA1

1

3

Pin 1-2 Close:

Normal Operation
(Default).

1

3

Pin 2-3 Close:

Clear CMOS data.

Pin Assignment

1 Ground
2 TX+
3 TX­4 Ground
5 RX­6 RX+
7 Ground

14

7

14

JCOM1: Serial Port Connector

The motherboard has a Serial Port Connector for connecting RS-232 Port.

Pin

Assignment

1 Carrier detect
2 Received data
3 Transmitted data
4 Data terminal ready
5 Signal ground
6 Data set ready

2

1

7 Request to send

10

8 Clear to send
9 Ring indicator

10 Key

9

JPRNT1: Printer Port Connector

This header allows you to connector printer on the PC.

G31-M4

2

1

26

25

Pin Assignment Pin Assignment

1 -Strobe 14 Ground

2 -ALF 15 Data 6
3 Data 0 16 Ground
4 -Error 17 Data 7

5 Data 1 18 Ground
6 -Init 19 -ACK

7 Data 2 20 Ground
8 -Scltin 21 Busy
9 Data 3 22 Ground

10 Ground 23 PE
11 Data 4 24 Ground

12 Ground 25 SCLT
13 Data 5 26 Key

15

Motherboard Manual

CHAPTER 4: USEFUL HELP

4.1 D

RIVER INSTALLATION NOTE

After you installed your operating system, please insert the Fully Setup
Driver CD into your optical drive and install the driver for better system
performance.

You will see the following window after you insert the CD

The setup guide will auto detect your motherboard and operating system.

Note:

If this window didn’t show up after you insert the Driver CD, please use file browser to
locate and execute the file SETUP.EXE under your optical drive.

A. Driver Installation

To install the driver, please click on the Driver icon. The setup guide will
list the compatible driver for your motherboard and operating system.
Click on each device driver to launch the installation program.

B. Software Installation

To install the software, please click on the Software icon. The setup guide
will list the software available for your system, click on each software title
to launch the installation program.

C. Manual

Aside from the paperback manual, we also provide manual in the Driver
CD. Click on the Manual icon to browse for available manual.

Note:

You will need Acrobat Reader to open the manual file. Please download the latest version
of Acrobat Reader so ftware from
http://www.adobe.com/products/acrobat/readstep2.html

16

G31-M4

e

4.2 SOFTWARE

Installing Software

1. Insert the Setup CD to the optical drive. The drivers installation program
would appear if the Autorun function has been enabled.

2. Select

3. Follow the on-screen instructions to complete the installation.

Launching Software

After the installatio n process, you will see the software icon “eHOT Line” /
“BIOS Update” appears on the desktop. Double-click the icon to launch the
utility.

eHot-Line (Optional)

eHot-Line is a convenient utility that helps you to contact with our
Tech-Support system. This utility will collect the system information which is
useful for analyzing the problem you may have encountered, and then send
these information to our tech-support department to help you fix the problem.

re pr esent s im por ta nt

*

information that you
must provide. Without
this inf ormation, you may
not be able to send out
the mail.

Software Installatio n, and then click on the respective software

title.

Before you use this uti lity, please set Outlook Express as yo ur default e-mail client applicatio n progra m.

This block will show
the information which
would be collected in
the mail.

Describe condition

*

of your system.

Select your area or

*

the area cl os e to you.

Provide the e-mail
address that you would
like to s end the copy to.

Pr ovid e the na me of

*

the memor y module
manufacturer.

Provide the name of
th e powe r su ppl y
manufacturer and the
model no.

Se nd th e mai l out .

Sav e the se info rma tion t o a .t xt fil

Exit this dialog.

17

Motherboard Manual

After filling up this information, click “Send”
to send the mail out. A warning dialog would
appear asking for your confirmation; click

Send” to confirm or “Do Not Send” to cancel.

“

If you want to save this information to a .txt file, click “

Save As…” and then you

will see a saving dialog appears asking you to enter file name.

Enter the file name and then click
“

Save”. Your system information

will be saved to a .txt file.

18

Open the saved .txt file, you will see
your system information including
motherboard/BIOS/CPU/video/
device/OS information. This
information is also concluded in the
sent mail.

We will not share customer ’s data with any other third parties,

so please feel free to provide your system information while using
eHot-Line service.

If you are not using Outlook Express as your default e-mail client
application, you may need to save the system information to a .txt file
and send the file to our tech support with other e-mail application.
Go to the following web

http://www.biostar.com.tw/app/en-us/about/contact.php

for getting

our contact information.

BIOS Update

BIOS Update is a convenient utility which allows you to update your
motherboard BIOS under Windows system.

G31-M4

AWARD BIOS AMI BIOS

Clear CMOS function

(Only for AWARD BIOS)

Show current BIOS information

Save cur rent B IOS

to a .bin file

Update BIOS

with a BIOS file

<Backup BIOS>

Once click on this button, the saving

dialog will show. Choose the

position to save file and enter file

name. (We recommend that the file

name should be English/number

and no longer than 7 characters.)

Then click

Save.

19

Motherboard Manual

<Update BIOS>

Before doing this, please download the proper BIOS file from the website.

For AWARD BIOS, update BIOS procedure
should be run with Clear CMOS function, so
please check on Clear CMOS first.

Then click Update BIOS button, a
dialog will show for asking you backup
current BIOS. Click Yes for BIOS
backup and refer to the Backup BIOS
procedure; or click No to skip this
procedure.

After the BIOS Backup procedure, the
open dialog will show for requesting the
BIOS file which is going to be updated.
Please choose the proper BIOS file for
updating, then click on Open.

The utility will update BIOS with the
proper BIOS file, and this process may
take minutes. Please do not open any
other applications during this process.

After the BIOS Update process, click on
OK to restart the system.

While the system boots up and the full screen logo shows, press <Delete>
key to enter BIOS setup.

In the BIOS setup, use the Load Optimized Defaults function and then Save and
Exit Setup to exit BIOS setup. BIOS Update is completed.

All the information and content above about the software are subject to be changed
without notice. For better performance, the software is being co ntinuously updated.
The information and pictures described above are for your reference only. The actual
information and settings on board may be slightly different from this manual.

20

4.3 EXTRA INFORMATION

CPU Overheated

If the system shutdown automatically after power on system for
seconds, that means the CPU protection function has been activated.

When the CPU is over heated, the motherboard will shutdown
automatically to avoid a damage of the CPU, and the system may not
power on again.

In this case, please double check:

1. The CPU cooler surface is placed evenly with the CPU surface.

2. CPU fan is rotated normally.

3. CPU fan speed is fulfilling with the CPU speed.

After confirmed, please follow steps below to relief the CPU protection
function.

1. Remove the power cord from power supply for seconds.

2. Wait for seconds.

3. Plug in the power cord and boot up the system.

Or you can:

1. Clear the CMOS data.
(See “Close CMOS Header: JCMOS1” section)

2. Wait for seconds.

3. Power on the system again.

G31-M4

21

Motherboard Manual

BIO-Flasher

BIO-Flasher is a BIOS flashing utility providing you an easy and simple way to
update your BIOS via USB pen drive or floppy disk.

The BIO-Flasher is built in the BIOS chip. To enter the utility, press <F12>
during the Power-On Self Tests (POST) procedure while booting up.

Updating BIOS with BIO-Flasher

1. Go to the website to download the latest BIOS file for the motherboard.

2. Then, save the BIOS file into a USB pen drive or a floppy disk.

3. Insert the USB pen drive or the floppy disk that contains the BIOS file to the
USB port or the floppy disk drive.

4. Power on or reset the computer and then
press <F12> during the POST process.
A select dialog as the picture on the right
appears.
Select the device contains the BIOS file and
press <Enter> to enter the utility.

22

5. The utility will show the BIOS
files and their respective
information. Select the proper
BIOS file and press <Enter>
then <Y> to perform the BIOS
update process.

6. After the update process, the utility will ask you to reboot the system.
Press <Y> to proceed. BIOS update completes.

z This utility only allows storage device with FAT32/16 format and single

parti tion.

z Shutting down or resetting the system while updating the B IOS will lead to

system boot failure.

4.4 AMI BIOS BEEP CODE

Boot Block Beep Codes

Number of Beeps Description

1 No media present. (Insert diskette in floppy drive A:)

2

3 Insert next diskette if multiple diskettes are used for recovery
4 Flash Programming successful
5 File read error

7 No Flash EPROM detected
10 Flash Erase error
11 Flash Program error
12 “AMIBOOT.ROM” file size error

13

POST BIOS Beep Codes

Number of Beeps Description

1 Memory refresh timer error

3 Base memory read/write test error

6 Keyboard controller BAT command failed

7 General exception error (processor exception interrupt error)

8 Display memory error (system video adapter)

“AMIBOOT.ROM” file not found in root directory of diskette in
A:

BIOS ROM image mismatch (file layout does not match
image present in flash device)

G31-M4

Troubleshooting POST BIOS Beep Codes

Number of Beeps Troubleshooting Action

1, 3 Reseat the memory, or replace with known good modules.

Fatal error indicating a serious problem with the system.
Consult your system manufacturer. Before declaring the
motherboard beyond all hope, eliminate the possibility of
interference by a malfunctioning add-in card. Remove all
expansion cards except the video adapter.

6, 7

8

z If beep codes are generated when all other expansion

cards are absent, consult your system manufacturer’s
technical support.

z If beep codes are not generated when all other expansion

cards are absent, one of the add-in cards is causing the
malfunction. Insert the cards back into the system one at a
time until the problem happens again. This will reveal the
malfunctioning card.

If the system video adapter is an add-in card, replace or
reseat the
video adapter. If the video adapter is an integrated part of the
system board, the board may be faulty.

23

Motherboard Manual

4.5 TROUBLESHOOTING

Probable Solution

1. There is no power in the system.
Power LED does not shine; the
fan of the power supply does not
work

2. Indicator light on keyboard does
not shine.

System is inoperative. Keyboard lights
are on, power indicator lights are lit,
and hard drives are running.

System does not boot from a hard disk
drive, but can be booted from optical
drive.

System only boots from an optical
drive. Hard disks can be read,
applications can be used, but system
fails to boot from a hard disk.

Screen message shows “Invalid
Configuration” or “CMOS Failure.”

System cannot boot after user installs a
second hard drive.

1. Make sure power cable is
securely plugged in.

2. Replace cable.

3. Contact technical support.

Using even pressure on both ends of
the DIMM, press down firmly until the
module snaps into place.

1. Check cable running from disk to
disk controller board. Make sure
both ends are securely plugged
in; check the drive type in the
standard CMOS setup.

2. Backing up the hard drive is
extremely important. All hard
disks are capable of breaking
down at any time.

1. Back up data and applications
files.

2. Reformat the hard drive.
Re-install applications and data
using backup disks.

Review system’s equipment. Make sure
correct information is in setup.

1. Set master/slave jumpers
correctly.

2. Run SETUP program and select
correct drive types. Call the drive
manufacturers for compatibility
with other drives.

24

G31-M4

This page is intentionally left bank.

25

Motherboard Manual

APPENDIX: SPEC IN OTHER LANGUAGES

G

ERMAN

Sp ezif ika tio nen

CPU

FSB

Chipsatz

Super E/A

Arbeitsspeich

er

Sockel 478

Intel Pent ium4 /Celeron D / Celero n 3xx

Prozessoren (Maximales Watt: 95W)

800 / 533 MHz

Intel G31

Int e l ICH7

ITE 8721

Biet et die h äuf ig v erwend eten a lten Sup er

E/A-Funktionen.

Low Pin Count-Schnittstelle

DDR2 DIMM-Steckplätze x 2

Jeder DIMM unterstützt 256MB / 512MB /

1GB / 2GB DDR2.

Max. 4GB Arbeitsspeicher

Unterstützt Hyper-Threading / Execute Disable Bit /

Enhanced Inte l SpeedStep® / Int el Arch itecture- 64 /

Extended Memory 64 Technology

Umgebungskontrolle,

Hardware-Überwachung

Dual-Kanal DDR2 Speichermodul

Unterstützt DDR2 533/667/800

registrierte DIMMs. ECC DIMMs werden nicht

unterstützt.

(CPU mit 533 MHz FSB unterstützt nur DDR2 533)

(CPU mit 800 MHz FSB unterstützt nur DDR2 667/800)

Grafik

IDE

SATA

LAN

HD

Audio-Unters

tützung

Steckplätz e

26

GMA 3100 Max. 256MB gemeinsam benutzter Videospeicher

Int eg r ier t er ID E-Co ntro ller

Integrierter Serial ATA-Controller

Realtek RTL 8102EL

ALC662

PCI-Steckp latz x 2

PCI Express x16 Steckplatz x1

Ultra DMA 33 / 66 / 100 Bus Master- Modus

Unterstützt PIO-Modus 0~4,

Datentransferrate b is zu 3.0Gb /s

Konform mit der SATA-Spezifikation Version 2.0.

10 / 100 Mb/s Auto-Negotiation

Halb-/ Vollduplex-Funktion

Unterstützt High-Definition Audio

5.1-Kanal-Audioausgabe

Onboard-Ans

chluss

Rückseiten-E

/A

G31-M4

Sp ezif ika tio nen

Diskettenlaufwerkanschluss x1 Jeder Anschluss unterstützt 2 Diskettenlaufwerke

Druckeranschluss Anschluss x1 Jeder Anschluss unterstützt 1 Druckeranschluss

Serieller Anschluss x1

IDE-Anschluss x1 Jeder Anschluss unterstützt 2 IDE-Laufwerke

SATA-Anschluss x4 Jeder Anschluss unterstützt 1 SATA-Laufwerk

Fronttafelanschluss x1 Unterstützt die Fronttafelfunktionen

Front-Audioanschluss x1 Unterstützt die Fronttafel-Audioanschlussfunktion

CPU-Lüfter-Sockel x1 CPU-Lüfterstromversorgungsanschluss

System-Lüfter-Sockel x1 System-Lüfter-Stromversorgungsanschluss

"CMOS löschen"-S ockel x1

USB-Anschluss x2

Stromanschluss (24-polig) x1

St romansch luss (4-po lig ) x1

PS/2-Tastatur x1

PS/2-Maus x1

VGA-Anschluss x1

LAN-Anschluss x1

USB-Anschluss x4

Audioanschluss x3

Jeder Anschluss unterstützt 2

Fronttafel-USB-Anschlüsse

Platinengröße

OS-Unterstüt

zung

200 mm (B) X 235 mm (L)

Windows 2000 / XP / Vista / 7

Biostar behält sich das Recht vor, ohne Ankündigung

die Unterstützung für ein Betriebssystem

hinzuzufügen oder zu entfernen.

27

Motherboard Manual

FRENCH

Socket 478

UC

Bus frontal

Chipset

Super E/S

Mémoire

principale

Processeurs Intel Pentium4 /Celeron D /

Celeron 3xx (Wat t maximum : 95W)

800 / 533 MHz

Intel G31

Int e l ICH7

ITE 8721

Fournit la fonctionnalité de Super E/S

patrimoniales la plus utilisée.

Int e rfa ce à f aib le co mpt e d e b roches

Fentes DDR2 DIMM x 2

Chaque D IMM prend en c harge des DDR2

de 256Mo / 512Mo / 1Go / 2Go

Capacit é mé mo ir e max imale de 4G o

SPEC

Prend en charge les technologies Hyper-Threading /

d'ex écut ion de b it de désact ivat ion / Intel SpeedSt ep®

opt imisée/ d ' arch itect ure Int e l 64 / d e mémo ire

étendue 64

Initiatives de contrôle environnementales,

Mon iteur d e mat ériel

Modu le d e mémo ir e DDR2 à mode à doub le vo ie

Prend en charge la DDR2 533/667/800

Les DIMM à registres et DIMM avec code correcteurs

d'erreurs ne sont pas prises en charge

(UC avec FSB 533 MHz ne prend en charge que DDR2 533)

(UC avec FSB 800 MHz ne prend en charge que DDR2

667/800)

Graphiques GMA 3100 Mémoire vidéo partagée maximale de 256 Mo

IDE

SATA

LAN

Prise en

charg e

aud io HD

Fentes

Contrôleur IDE intégré

Contrô leur Serial ATA int é gr é

Realtek RTL 8102EL

ALC662

Fente PCI x2

Fente PC I Expres s x16 x1

Mode principale de Bus Ultra DMA 33 / 66 / 100

Prend en charge le mode PIO 0~4,

Taux de transfert jusqu'à 3.0Go/s.

Co nfo rme à la spécificat ion S ATA Vers ion 2. 0

10 / 100 Mb/s négociation automatique

Half / Full duplex capability

Prise en charg e de l'aud io haut e déf in ition

Sortie aud io à 5 .1 vo ies

28

Connecteur

embarqu é

E/S du

panneau

arrière

Dimensions

de la carte

Support SE

G31-M4

SPEC

Connecteur de disquette x1

Connecteur de Port d'imprimante x1 Chaque connector prend en charge 1 Port d'imprimante

Port série x1

Connecteur IDE x1

Connecteur SATA x4

Connecteur du panneau avant x1 Prend en charge les équipements du panneau avant

Connecteur Audio du panneau avant x1 Prend en charge la fonction audio du panneau avant

Embase de ventilateur UC x1 Alimentation électrique du ventilateur UC

Embase de ventilateur système x1 Alimentation électrique du ventilateur système

Embase d'effacement CMOS x1

Connecteur USB x2

Connecteur d' aliment at ion x1

(24 broches)

Connecteur d' aliment at ion x1

(4 broch es)

Clavier PS/2 x1

Souris PS/2 x1

Port VGA x1

Port LAN x1

Port USB x4

Fiche aud io x3

200 mm (l) X 235 mm (H)

Windows 2000 / XP / Vista / 7

Chaque co nnector prend en charge 2 lecteu rs de

disquettes

Chaque connect eur prend en ch arg e 2 périp hér iqu es

IDE

Chaque connect eur prend en ch arg e 1 périp hér iqu e

SATA

Chaque connecteur prend en charge 2 ports USB de

panneau avant

Biostar se réserve le droit d'ajouter ou de supprimer le

support de SE avec ou sans préavis.

29

Motherboard Manual

ITALIAN

SPECIFICA

Socket 478

CPU

FS B 800 / 533 MHz

Chipset

Super I/O

Memoria

principale

Grafica GMA 3100 La memoria video condivisa massima è di 256MB

Processori Intel Pentium4 /Celeron D /

Celeron 3xx (Watt massimo: 95W)

Intel G31

Int e l ICH7

ITE 8721

Fo rnis ce le fun zionalit à leg acy S u per

I/O usate più comunemente.

Interfaccia LPC (Low Pin Count)

Alloggi DIMM DDR2 x 2

Ciascun DIMM supporta DDR2 256MB

/ 512MB / 1GB / 2GB

Capacità massima della memoria 4GB

Supporto di Hyper-Threading / Execute Disable

Bit / Enhanced Inte l SpeedSt ep® / Architettura

Intel 64 / Tecnologia Extended Memory 64

Funzioni di controllo dell’ambiente:

Monitoraggio hardware

Modulo di memoria DDR2 a canale doppio

Supporto di DDR2 533/667/800

DIMM registrati e DIMM ECC non sono supportati

(CPU con FSB a 533 MHz supporta solo DDR2 533)

(CPU con FSB a 800 MHz supporta solo DDR2

667/800)

IDE Cont roller IDE integrato

SATA Controller Serial ATA integrato

LA N Realtek RTL 8102EL

Supporto

audio HD

Allo g gi

ALC662

Allo g gio PC I x2

Alloggio PCI Express x16 x1

30

Modalità Bus Master Ultra DMA 33 / 66 / 100

Supporto modalità PIO Mode 0-4

Velocità di trasferimento dei dati fino a 3.0Gb/s.

Co mp at ibile specifiche S ATA Vers ione 2.0.

Negoziazione automatica 10 / 100 Mb/s

Capacità Half / Full Dup lex

Supporto audio High-Definition (HD)

Uscita audio 5.1 canali

G31-M4

SPECIFICA

Connettore floppy x1 Ciascun connettore supporta 2 unità Floppy

Connettore Porta stampante x1 Ciascun connettore supporta 1 Porta stampante

Porta seriale x1

Connettore IDE x1 Ciascun connettore supporta 2 unità IDE

Connettore SATA x4 Ciascun connettore supporta 1 unità SATA

Co nnettore p an nello fr ont ale x1 Sup port a i servizi de l p anne l lo fr ont ale

Connettore audio frontale x1 Supporta la funzione audio pannello frontale

Connettori

su scheda

I/O

pannello

posteriore

Dimension

i scheda

Co llet t o re ven t olina C PU x1 A limentaz ione ven tolina CPU

Co llet t o re ven t olina sistema x1 A limentazione ventol ina d i s is t ema

Co llet t o re can ce l laz ione CMOS x1

Ciascun connettore supporta 2 porte USB

Connettore USB x2

pannello frontale

Connettore alimentazione x 1

(24 pin)

Connettore alimentazione x1

(4 pin)

Tas t iera P S / 2 x1

Mou s e PS/2 x1

Porta VGA x1

Porta LA N x 1

Porta USB x 4

Connettore audio x3

200 mm (larghezza) x 235 mm

(altez za)

Sistemi

operat ivi

supportati

W indo ws 20 00 / X P / V ist a / 7

Biostar si riserva il diritto di aggiungere o

rimuovere il supporto di qualsiasi sistema

operativo senza preavviso.

31

Motherboard Manual

SPANISH

Especificación

Conector 478

CPU

FSB 800 / 533 MHz

Conjunto de

chips

Súper E/S

Memoria

principal

Gráficos GMA 3100 Memoria máxima de vídeo compartida de 256MB

Proc esadores Intel Pent ium4 /Celeron D /

Celeron 3xx (Vatio máximo: 95W)

Intel G31

Int e l ICH7

ITE 8721

Le ofrece las funcionalidades heredadas de

us o más común Súper E /S.

Interfaz de cuenta Low Pin

Ranuras DIMM DDR2 x 2

Cada DIMM admite DDR de 256MB /

512MB / 1GB / 2GB

Capacidad máxima de memoria de 4GB

Admite Hyper-Threading / Bit de deshabilitación de

ejecución / Intel SpeedStep® Mejo rado / Intel

Architecture-64 / Tecnología Extended Memory 64

In iciat iv as de con tro l d e ent o rno ,

Monitor hardware

Módulo de memoria DDR2 de canal Doble

Admite DDR2 de 533/667/800

No admite DIMM registrados o DIMM compatibles con

ECC

(CPU con FSB de 533 MHz sólo soporta DDR2 533)

(CPU con FSB de 800 MHz sólo soporta DDR2 667/800)

IDE Controlador IDE integrado

SATA Controlador ATA Serie Integrado

Red Local Realtek RTL 8102EL

Soporte de

sonido HD

Ranuras

ALC662

Ranura PCI X2

Ranura PCI Express x16 X1

32

Modo bus maestro Ultra DMA 33 / 66 / 100

Soporte los Modos PIO 0~4,

Tasas de transferencia de hasta 3.0 Gb/s.

Co mp at ible con la ve rsión SATA 2.0.

Negociación de 10 / 100 Mb/s

Funciones Half / Full dúplex

Soporte de sonido de Alta Definición

Salida de sonido de 5.1 canales

G31-M4

Especificación

Conector disco flexible X1 Cada conector soporta 2 unid ades de disco flexible

Conector Puerto de impresora X1 Cada conector soporta 1 Puerto de impresora

Puert o ser ie X1

Conector IDE X1 Cada conector soporta 2 dispositivos IDE

Conector SATA X4 Cada conector soporta 1 dispositivos SATA

Co nect o r de p anel f ron tal X1 Sop o rta ins t a laciones en e l p ane l fr ont a l

Conectores

en p laca

Panel

trasero de

E/S

Ta mañ o d e

la placa

Conector de sonido frontal X1 Soporta funciones de sonido en el panel frontal

Cabecera de ventilador de CPU X1 Fuente de alimentación de ventilador de CPU

Cabecera de ventilador de sistema X1 Fuente de alimentación de ventilador de sistema

Cabecera de borrado de CMOS X1

Conector USB X2 Cada conector soporta 2 puertos USB fro ntales

Conector de alimentación X1

(24 patillas)

Conector de alimentación X1

(4 patillas)

Tec lad o P S /2 X 1

Ratón PS/2 X1

Puerto VGA X1

Puerto de red local X1

Puert o USB X4

Conector de sonido X3

200 mm. (A) X 235 Mm. (H)

Soporte de

sistema

operativo

Windows 2000 / XP / Vista / 7

Biostar se reserva el derecho de añadir o retirar el

soporte de cualquier SO con o sin aviso previo.

33

Motherboard Manual

PORTUGUESE

ESPECIFICAÇÕES

Socket 478

CPU

FSB 800 / 533 MHz

Chipset

Especificaçã

o Super I/O

Memória

principal

Placa

gráf ica

IDE Controlador IDE integrado

SATA Controlador Serial ATA integrado

LAN Realtek RTL 8102EL

Suporte

para áudio

de alta

definição

Ranhuras

Processadores Intel Pentium4 /Celeron D /

Celeron 3xx (Watt máximo: 95W)

Intel G31

Int e l ICH7

ITE 8721

Proporciona as funcionalidades mais

utilizadas em termos da especificação

Super I/O.

Interface LPC (Low Pin Count).

Ranhuras DIMM DDR2 x 2

Cada módulo DIMM suporta uma

memória DDR2 de 256 MB / 512 MB / 1GB

/ 2GB

Capacidad e máx ima de me mó r ia:4 GB

GMA 3100 Memória de vídeo máxima partilhada: 256 MB

ALC662

Ranhura PCI x2

Ranhura PCI Express x16 x1

Sup orta as tecno log ias Hyper-Threading / Execut e

Disab le Bit / Enhanced Int el SpeedStep® / Int el

Arquitecture -64 / Extended Memory 64

In iciat iv as para co ntro lo do amb ien te

Monitorização do hardware

Módulo de memória DDR2 de canal duplo

Suporta módulos DDR2 533/667/800

Os módulos DIMM registados e os DIMM ECC não são

suportados

(CPU com FSB 533 MHz só suporta DDR2 533)

(CPU com FSB 800 MHz só suporta DDR2 667/800)

Modo Bus master Ultra DMA 33 / 66 / 100

Suporta o modo PIO 0~4,

Velocidades de transmissão de dados até 3.0 Gb/s.

Compat ibilidade co m a es pecificação SATA versão 2.0.

Auto negociação de 10 / 100 Mb/s

Capacidade semi/full-duplex

Suporta a especificação High-Definition Audio

Saída de áudio de 5.1 canais

34

Conectores

na placa

Entradas/S

aídas no

painel

traseiro

Tamanho

da placa

Sistemas

operativos

suportados

G31-M4

ESPECIFICAÇÕES

Conector da unidade de disquetes x1 Cada conector suporta 2 unidades de disquetes

Conector da para impressora x1 Cada conector suporta 1 Porta para impressora

Porta série x1

Conector IDE x1 Cada conector suporta 2 dispositivos IDE

Conector SATA x4 Cada conector suporta 1 dispositivo SATA

Conector do painel frontal x1 Para suporte de várias funções no painel frontal

Conector d e áud io fronta l x1 Suporta a fun ção de áud io no painel frontal

Conector da ventoinha da CPU x1 Alimentação da ventoinha da CPU

Conector da ventoinha do s istema x1 Alimentação da ventoinha do sistema

Conector para limpeza do CMOS x1

Conector USB x2 Cada conector suporta 2 portas USB no painel frontal

Conector de alimentação x1

(24 pinos)

Conector de alimentação x1

(4 p inos)

Tec lad o P S /2 x 1

Rato PS/2 x1

Porta VGA x1

Porta LA N x1

Porta USB x4

Tomada de áudio x3

200 mm (L) X 235 mm (A)

Windows 2000 / XP / Vista / 7

A Biostar reserva-se o direito de adicionar ou remover

suporte para qualquer sistema operativo com ou sem

av iso pr év io .

35

Motherboard Manual

POLISH

SPEC

Socket 478

Procesor

FSB 800 / 533 MHz

Chipset

Pamięć

główna

Grafika GMA 3100

Super I/O

Intel Pent ium4 /Celeron D / Celero n 3xx

Procesory (Maksymalny Watt: 95W)

Intel G31

Int e l ICH7

Gniazda DDR2 DIMM x 2

Każde gniazdo DIMM obs ługuje moduły

256MB / 512MB / 1GB / 2GB

Maks. wielkość pamięci 4GB

ITE 8721

Zapewnia najbardziej powszechne funkcje

Super I/O.

Interfejs Low Pin Count

Obsługa Hyper-Threading / Execute Disable Bit /

Enhanced Inte l SpeedStep® / Int el Arch itecture-64 /

Extended Memory 64 Technology

Mod uł pamięci DDR2 z trybem podwójnego kanału

Obsługa DDR2 533/667/800

Brak obsług i Regist er ed D IMM oraz ECC D IMM

(CPU z FSB 533 MHz tylko obsługuje pamięci DDR2 533)

(CPU z FSB 800 MHz tylko obsługuje pamięci DDR2

667/800)

Maks. wielkość współdz ielonej pam ięci video wynosi

256MB

Funkcje kontroli warunków pracy,

Mon itor H /W

IDE Zintegrowany kontroler IDE

SATA Zintegrowany kontroler Serial ATA

LAN Realtek RTL 8102EL

Obsługa

aud io HD

Gniazda

ALC662

Gniazdo PCI x2

Gniazdo PCI Express x16 x1

36

Ultra DMA 33 / 66 / 100 Tryb Bus Master

obsługa PIO tryb 0~4,

Transfer danych do 3.0 Gb/s.

Zgodność ze specyfikacją SATA w wersji 2.0.

10 / 100 Mb/s z automatyczną negocjacją szybko ści

Działanie w trybie połowicznego / pełn ego dupleksu

Obsługa H igh- Def inition A ud io

5.1 kanałowe wyjście audio

Złącza

wbud owan e

SPEC

Złącze napędu dyskietek x1 Każde złącze obs ługuje 2 napędy dyskietek

Złącze Port drukarki x1 Każde złącze obs ługuje 1 Port drukarki

Port szeregowy x1

Złącze IDE x1 Każde złącze obs ługuje 2 urządzenia IDE

Złącze SATA x4 Każde złącze obsługuje 1 urządzenie SATA

Złącze panela przedniego x1 Obsługa elementów panela przedniego

Przedn ie złącze audio x1 Obsługa funkcji audio na panelu przednim

Złącze głó wkow e went ylatora

procesora x1

Zasilanie wentylatora procesora

G31-M4

Back Panel

I/O

Wymiary

płyty

Obsluga

systemu

operacyjne

go

Złącze głó wkow e went ylatora

systemowego x1

Złącze głó wkowe kasowan ia CMOS x 1

Złącze USB x2

Złącze zasilania (24 pinowe) x1

Złącze zas ilania (4 p ino we ) x 1

Klawiatura PS/2 x1

Mys z PS /2 x1

Port VGA x1

Port LAN x1

Port USB x4

Gniazdo audio x3

200 mm (S) X 235 mm (W)

Windows 2000 / XP / Vista / 7

Zasilanie wentylatora systemowego

Każde złącze obs ługuje 2 porty USB na panelu

przednim

Biostar zastrzega sobie prawo dodawania lub

odwoływ ania obsług i dowo lneg o s ys t emu

operacyjnego b ez powiado mienia.

37

Motherboard Manual

RUSSIAN

CPU

(центральн

ый

процессор)

FSB

Набо р

микросхем

Основная

память

Графика

Super I/O

IDE

SATA

Локальна я

сеть

Звуко вая

поддержка

жестког о

диска

Слоты

Гнездо 478

Процессоры Intel Pent iu m4 /C eleron D /

Celeron 3xx (Максимальный ват т: 9 5W )

800 / 533 МГц

Intel G31

Int e l ICH7

Слоты DDR2 DIMM x 2

Каждый модуль DIMM поддерживает

256 МБ / 512МБ / 1ГБ / 2ГБ DDR2

Максимальная ёмкость памяти 4ГБ

GMA 3100

ITE 8721

Обеспечивает наиболее используемые

действующие фун кцио наль ны е

возможно сти Super I/O.

Интерфейс с ни зким количес твом

выводов

Встроенное устройство управления

встроенными интерфейсами устройс тв

Встроенное последовательно е

устройс тво управления ATA

Realtek RTL 8102EL

ALC662

Слот PCI x2

Слот PCI Express x16 x1

СПЕЦ

Поддержка технологий Hyper-Threading / Execute

Disab le Bit / Enhanced Int el SpeedStep® / Int el

Architecture-64 / Extended Memory 64 Technology

Мод ул ь памяти с двухкан альным режимом DDR2

Поддержка DDR2 533/667/800

Не поддерживает зарегистрированные модули

DIMM and ECC DIMM

(Процессор с ФСБ 533 МГц поддерживает только

DDR2 533)

(Процессор с ФСБ 800 МГц поддерживает только

DDR2 667/800)

Максимальная совместно использ уемая вид ео

память составляет 256 МБ

Инициативы по охране окружающей среды,

Аппаратный монитор

Режим "хозяина" шины Ultra DMA 33 / 66 / 100

Поддержка режима PIO 0~4,

скорость передачи данных до 3.0 гигабит/с.

Соответствие спецификации SATA версия 2.0.

Автоматическо е согласование 10 / 100 Мб /с

Частичная / полна я дуплексная способность

Звуко вая поддержка H igh- Def inition

5.1канальный звуковой выход

38

Встроенны

й разъём

Задняя

панель

средств

ввода-выв

ода

Разм ер

панели

Поддержка

OS

G31-M4

СПЕЦ

Разъ ём НГМД x1

Разъ ём Порт подключения

принтера x1

Последо ват ельный порт x1

Разъ ём IDE x 1

Разъ ём SATA x4 Каждый разъём поддерживает 1 устройс тво SATA

Разъ ём на лицевой панели x1 Поддержка устройс тв на лицевой панели

Входной звуковой разъём x1 Поддержка звуко вых функций на лицевой панели

Контактирующее приспособление

вентил ятор а центрального процессора

x1

Контактирующее приспособление

вентил ятор а системы x1

Открытое контактирующее

приспособление CMOS x1

USB- разъём x2

Разъ ем питания (24 вы вод) x1

Разъ ем питания (4 вывод) x1

Клавиатура PS/2 x1

Мышь PS/2 x1

Пор т VGA x1

Пор т LAN x1

USB- порт x4

Гнездо для подключени я

наушников x3

200 мм (Ш) X 235 мм (В)

Windows 2000 / XP / Vista / 7

Каждый разъём поддерживает 2 накопителя на

гибких магнитных дисках

Каждый разъём поддерживает 1 По рт подключения

принтера

Каждый разъём поддерживает 2 встроенных

интерфейса накопителей

Источник пит ания для вентил ятора центрального

процессора

Источник пит ания для вентил ятора системы

Каждый разъём поддерживает 2 USB-порта на

лицевой панели

Biostar сохраняет за собой право добавлять или

удаля ть средства обеспечения для OS с или без

предварительного уведом ле ния .

39

Motherboard Manual

ARABIC

تﺎﻔﺻاﻮﻤﻟا

تﺎﻴﻨﻘﺗ ﻢﻋﺪﺗHyper-Threading / Execute Disable Bit /

Enhanced Inte l SpeedStep® / Int e l Architecture-64 /

Extended Memory 64 Technology

ةﺮآاذ ةﺪﺣوDDR2 ﻘﻟا ﺔﺝودﺰﻣةﺎﻨ

عﻮﻥ ﻦﻣ ةﺮآاﺬﻟا ﻢﻋﺪﺗDDR2 تﺎﻌﺳ 800/667/533ﺖیﺎﺏ ﺎﺠﻴﻣ

ةﺮآاﺬﻟا ﻖﺋﺎﻗر ﻢﻋﺪﺗ ﻻDIMM ﻓاﻮﺘﺗ ﻻ ﻲﺘﻟا ﻚﻠﺗو ﻊﻣ ﻖ ECC

(533 ﺰﺗﺮهﺎﺠﻴﻣ ﻊﻣ ةﺪﺣو ﺔﺠﻟﺎﻌﻤﻟا ﺔیﺰآﺮﻤﻟا ﺰﺗﺮﻴهﺎﻐﻴﻣ ﻂﻘﻓ ﻢﻋﺪﺗ

DDR2 533)

(800 ﺰﺗﺮهﺎﺠﻴﻣ ﻊﻣ ةﺪﺣو ﺔﺠﻟﺎﻌﻤﻟا ﺔیﺰآﺮﻤﻟا ﺰﺗﺮﻴهﺎﻐﻴﻣ ﻂﻘﻓ ﻢﻋﺪﺗ

DDR2 667/800)

ﺔآﺮﺘﺸﻤﻟا ﻮیﺪﻴﻔﻟا ةﺮآاﺬﻟ ﺔﻌﺳ ﻰﺼﻗأ256ﺖیﺎﺏ ﺎﺠﻴﻣ

ﺔﺌﻴﺒﻟا ﻲﻓ ﻢﻜﺤﺘﻟا ﻞﺋﺎﺳو:

ةﺰﻬﺝﻷا ﺔﻟﺎﺣ ﺔﻓﺮﻌﻤﻟ ﺐﻗاﺮﻣ

ﺲﺒﻘﻣ478

تﺎﺠﻟﺎﻌﻣIntel Pent iu m4 /C e leron D / Cel er on

(طاو ﺺﻗىو: 95و) 3xx

ددﺮﺗ 800 / 533 ﺰﺗﺮه ﺎﺠﻴﻣ

Intel G31

Int e l ICH7

ﺔﺤﺘﻓ ﻞآ ﻢﻋﺪﺗDIMM عﻮﻥ ﻦﻣ ةﺮآاذ ﻢﻋﺪﺗ DDR2 ﺔﻌﺳ

256/512 و ﺖیﺎﺏ ﺎﺠﻴﻣ 2و ﺖیﺎﺏ 1 ﺎﺠﻴﺝﺖیﺎﺏ

GMA 3100

ITE 8721

ﺔﻔﻴﻇ و ﺮﻓﻮﺗSuper I/O ًﺎ ﻣ ا ﺪ ﺨ ﺘﺳا ﺮﺜآﻷا .

ﺗﻢﻋﺪ ﺔﻴﻨﻘﺗ Low Pin Co unt Inter face

ةﺪﺣو ﺔﺠﻟﺎﻌﻤﻟا

ﺔیﺰآﺮﻤﻟا

ﻞﻗﺎﻨﻟا ﻲﻣﺎﻣﻷا ﻲﺒﻥﺎﺠﻟا

ﺔﻋﻮﻤﺠﻣ ﺢﺋاﺮﺸﻟا

ﺔﺤﺘﻓDDR2 DIM M دﺪﻋ2

ةﺮآاﺬﻟا ﺔﻴﺴﻴﺋﺮﻟا

ﺳ ىﻮﺼﻗ ةﺮآاذ ﺔﻌ4 ﺖیﺎﺏ ﺎﺠﻴﺝ

ﺔﻗﺎﻄﺏ تﺎﻣﻮﺳﺮﻟا

Super I/O

40

ﺔﻴﻨﻘ ﺘﺏ ﻞﻗﺎﻥUltra DMA 33 / 66 / 100ﻲﺴﻴﺋر ﻊﺿو

ﻊﺿو ﻢﻋدPIO Mode 0~4

ﻞﻘﻥ تﺎﻥﺎﻴﺒﻟا تﺎﻋﺮﺴﺏ ﻞﺼﺗ ﻰﻟإ 3.0 ﺖﺏﺎﺠﻴﺝ/ﺔﻴﻥﺎﺙ.

ﺔﻘﺏﺎﻄﻣ تﺎﻔﺹاﻮﻤﻟ SATA راﺪﺹﻹا 2.0.

ﻲﺋﺎﻘﻠﺗ ضو ﺎﻔﺗ10/100 ﺖیﺎﺏ ﺎﺠﻴﻣ /ﺔﻴﻥﺎﺙ

ﺔﻴﻥﺎﻜﻣإﻞﻣﺎﻜﻟا جودﺰﻤﻟا ﻞﻘﻨﻟا /ﻲﻔﺼﻨﻟا

ﻦﻣ ﻒیﺮﻌﺘﻟا ﻲﻟ ﺎﻋ تﻮﺼﻟا ﺔﻴﻨﻘﺗ ﻢﻋﺪﺗ

5.1 تﻮﺼﻟا جﺮﺨﻟ تاﻮﻨﻗ

ﺔﺤﺘﻓPCI دﺪﻋ2

ﺔﺤﺘﻓx16 PCI Express دﺪﻋ1

ﻢﻜﺤﺘﻣIDE ﻞﻣﺎﻜﺘﻣ

ﻢﻜﺤﺘﻣ Serial ATA ﻞﻣﺎﻜﺘﻣ

Realtek RTL 8102EL

ALC662

ﺬﻔﻨﻣ ID E

SATA

ﺔﻜﺒﺷ ﺔﻴﻠﺧاد

ﻢﻋد تﻮﺼﻟا ﻲﻟﺎﻋ

ﻒیﺮﻌﺘﻟا

تﺎﺤﺘﻔﻟا

تﺎﻔﺻاﻮﻤﻟا

G31-M4

ﺔﻥﺮﻤﻟا صاﺮﻗﻸﻟ ﻦﻴآ ﺮﺤﻣ ﻢﻋﺪی

ﺔﻌﺏﺎﻃ ﺬﻔﻨﻣ دﺪﻋ1

ﻲﻠﺴﻠﺴﺗ ﺬﻔ ﻨﻣ دﺪﻋ1

ةﺰﻬﺝأ ﻦﻣ ﻦﻴﻨﺙا ﺬﻔﻨﻣ ﻞآ ﻢﻋﺪیIDE

ةﺰﻬﺝأ ﻦﻣ ﺪﺣاو ﺬﻔﻨﻣ ﻞآ ﻢﻋﺪیSATA

ﺔﻴﻣﺎﻣﻷا ﺔﺣﻮﻠﻟا تاﺰﻴﻬﺠﺗ ﻢﻋﺪی

ﺔﻴﻣﺎﻣﻷا ﺔﺣﻮﻠﻟ ﺎﺏ تﻮﺼﻟا ﺔﻔﻴﻇو ﻢﻋﺪی

ﺔﻔﻴﻇو ﻊﻣ ﺔﺠﻟﺎﻌﻤﻟا ةﺪﺣو ﺔﺣوﺮﻤﻟ ﺔﻗﺎﻄ ﻟا ﻞﻴﺹﻮﺘﻟ

مﺎﻈﻨﻟا ﺔﺣوﺮﻤﻟ ﺔﻗﺎﻄﻟا ﻞﻴﺹﻮﺘﻟ

ﺢﺴ ﻣ ﺔﻠﺹوCMOS دﺪﻋ1

ﻲﺘﺤﺘﻓ ﺬﻔﻨﻣ ﻞآ ﻢﻋﺪیUSBﺔﻴﻣﺎﻣﻷا ﺔﺣﻮﻠﻟﺎﺏ

ﻴﺹﻮﺗ ﺬﻔﻨﻣ ﺔﻗﺎﻄﻟا ﻞ)24سﻮﺏد( دﺪﻋ1

ﺔﻗﺎﻄﻟا ﻞﻴﺹﻮﺗ ﺬﻔﻨﻣ)4ﺲﻴﺏﺎﺏد( دﺪﻋ1

ﺔﻥﺮﻣ صاﺮﻗأ كﺮﺤﻣ ﺬﻔﻨﻣ دﺪﻋ1

ﺬﻔﻨﻣIDE دﺪﻋ1

ﺬﻔﻨﻣSATA دﺪﻋ4

ﺔﻴﻣﺎﻣﻷا ﺔﺣﻮ ﻠﻟا ﺬﻔﻨﻣ دﺪﻋ1

ﻣﻲﻣﺎﻣﻷا تﻮﺼﻟا ﺬﻔﻨ دﺪ ﻋ1

ﺬﻓﺎﻨﻤﻟا ﻰﻠﻋ ﺢﻄﺳ

ﺔیﺰآﺮﻤﻟا ﺔﺠﻟﺎﻌﻤﻟا ةﺪﺣو ﺔﺣوﺮﻣ ﺔﻠﺹو دﺪﻋ1

ﺔﺣﻮﻠﻟا

مﺎﻈﻨﻟا ﺔﺣوﺮﻣ ﺔﻠﺹو دﺪﻋ1

ﺬﻔﻨﻣUS B دﺪﻋ2

ﺢﻴﺗﺎﻔﻣ ﺔﺣﻮﻟPS/2 دﺪﻋ1

سوﺎﻣ PS/2 دﺪﻋ1

ﺬﻔﻨﻣVGA دﺪﻋ1

ﺔﻴﻠﺤﻣ لﺎﺼﺗا ﺔﻜﺒﺵ ﺬﻔﻨﻣ دﺪﻋ1

ﺬﻓﺎﻨﻣ ﻞﺧد/جﺮﺧ

ﺔﺣﻮﻠﻟا ﺔﻴﻔﻠﺨﻟا

ﻆﻔﺘﺤﺗ Biostar ﺎﻬﻘﺤﺏ ﻲﻓ ﺔﻓ ﺎﺿإ وأ ﺔﻟازإ ﻢﻋﺪﻟا يﻷ مﺎﻈﻥ ﻞﻴﻐﺸﺗ رﺎﻄﺧﺈﺏ وأ نوﺪﺏ

200 ﻢﻣ)ضﺮﻋ (X 235 ﻢﻣ)عﺎﻔﺗرا(

رﺎﻄﺧإ.

ﺬﻓﺎﻨﻣUS B دﺪﻋ4

تﻮﺹ ﺲﺒﻘﻣ دﺪﻋ3

Windows 2000 / XP / Vista / 7

ﻢﺠﺣ ﺔﺣﻮﻠﻟا

ﻢﻋد ﺔﻤ ﻈﻥأ ﻞﻴﻐﺸﺘﻟا

41

Motherboard Manual

JAPANESE

仕様

Socket 478

CPU

FSB

チップセット

メインメモリ

グラフィック

ス

Super I/O

IDE 統合ID Eコントローラ

SATA 統合シリアルATA コントローラ

LAN Realtek RTL 8102EL

Intel Pent ium4 /Celeron D / Celero n 3xx

プロセッサ(最高のワット: 95W)

800 / 533 MHz

Intel G31

Int e l ICH7

DDR2 DIMMスロット x 2

各DIMMは 256MB / 512MB / 1GB / 2GB

DDR2をサポート

最大メモリ容量4GB

GMA 3100 最大の共有ビデオメモリは256MBです

ITE 8721

もっとも一般に使用されるレガシーSuper I/O

機能を採用しています。

低ピンカウントインターフェイス

Hyper-Threading / Execute Disab le Bit / Enhanced Inte l

SpeedSt ep® / Intel Architecture-64 / Extended

Memory 64 Technologyをサポートします

デュアル チャンネルモードDDR2メモリモジュール

DDR2 533/667/800をサポート

登録済みDIMMとECC DIMMはサポートされません

(のCPUのFSBを533 MHzの唯一のDDR2 533をサポートし

ています)

(のCPUのFSBを800 MHzの唯一のDDR2 667/800をサポー

トしています)

環境コントロールイニシアチブ、

H/Wモニター

Ultra DMA 33 / 66 / 100バスマスタモード

PIO Mode 0~4のサポート、

最高3.0 Gb/秒のデータ転送速度

SATAバージョン2.0仕様に準拠。

10 / 100 Mb/秒のオートネゴシエーション

半/全二重機能

HDオーディ

ALC662

オのサポート

PCIスロット x2

スロット

PCI Express x16スロット x1

ハイデフィニションオーディオのサポート

5.1 チャンネルオーディオアウト

42

オンボードコ

ネクタ

背面パネル

I/O

G31-M4

仕様

フロッピーコネクタ x1 各コネクタは2つのフロッピードライブをサポートします

プリンタポートコネクタ x1 各コネクタは1つのプリンタポートをサポートします

シリアルポート x1

IDE コネクタ x1 各コネクタは2つのID Eデバイスをサポートします

SATAコネクタ x4 各コネクタは1つのSATAデバイスをサポートします

フロントパネルコネクタ x1 フロントパネル機能をサポートします

フロントオーディオコネクタ x1 フロントパネルオーディオ機能をサポートします

CPUファンヘッダ x1 CPUファン電源装置

システムファンヘッダ x1 システムファン電源装置

CMOSクリアヘッダ x1

USBコネクタ x2

電源コネクタ(24 ピン) x1

電源コネクタ(4ピン) x1

PS/2キーボード x1

PS/2マウス x1

VGAポート x1

LANポート x1

USBポート x4

オーディオジャック x3

各コネクタは2つのフロントパネルUSBポートをサポートし

ます

ボードサイズ

OSサポート W indows 2000 / XP / Vista / 7

200 mm (幅) X 235 mm (高さ)

Biostarは事前のサポートなしにOSサポートを追加または削

除する権利を留保します。

2010/08/05

43