Biostar BIH11-AHA User Manual

Page 1

FCC Informaon and Copyright

This equipment has been tested and found to comply with the limits of a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protecon against harmful interference in a residenal installaon. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instrucons, may cause harmful interference to radio communicaons. There is no guarantee that interference will not occur in a parcular installaon.

The vendor makes no representaons or warranes with respect to the contents here and specially disclaims any implied warranes of merchantability or tness for any purpose. Further the vendor reserves the right to revise this publicaon and to make changes to the contents here without obligaon to nofy any party beforehand. Duplicaon of this publicaon, in part or in whole, is not allowed without rst obtaining the vendor’s approval in wring.

The content of this user’s manual is subject to be changed without noce and we will not be

responsible for any mistakes found in this user’s manual. All the brand and product names are

trademarks of their respecve companies.

Dichiarazione di conformità sinteca

Ai sensi dell’art. 2 comma 3 del D.M. 275 del 30/10/2002

Si dichiara che questo prodoo è conforme alle normave vigen e soddisfa i requisi essenziali richies dalle direve

2004/108/CE, 2006/95/CE e 1999/05/CE quando ad esso applicabili

Short Declaraon of conformity

We declare this product is complying with the

laws in force and meeng all the essenal requirements as specied by the direcves

2004/108/CE, 2006/95/CE and 1999/05/CE whenever these laws may be applied

Page 2

BIH11-AHA User’s Manual

Table Of Contents

FCC Informaon and Copyright �� 1

Chapter 1: Introducon �� 3

1.1 Before You Start .................................................................................................................. 3

1.2 Specicaons ...................................................................................................................... 4

1.3 Rear Panel Connectors ........................................................................................................ 5

1.4 Motherboard Layout ........................................................................................................... 6

Chapter 2: Hardware installaon �� 7

2.1 Central Processing Unit (CPU) ............................................................................................. 7

2.2 Install a Heatsink ................................................................................................................. 9

2.3 Connect Cooling Fans ....................................................................................................... 10

2.4 Installing System Memory ................................................................................................ 10

2.5 Expansion Slots ................................................................................................................. 12

2.6 Jumper & Switch Seng ................................................................................................... 13

2.7 Headers & Connectors ...................................................................................................... 14

2 | Table Of Contents

Page 3

BIH11-AHA User’s Manual

Chapter 1: Introducon

1�1 Before You Start

Thank you for choosing our product. Before you start installing the motherboard, please make

sure you follow the instrucons below:

• Prepare a dry and stable working environment with sucient lighng.

• Always disconnect the computer from power outlet before operaon.

• Before you take the motherboard out from an-stac bag, ground yourself properly

by touching any safely grounded appliance, or use grounded wrist strap to remove the

stac charge.

• Avoid touching the components on motherboard or the rear side of the board unless necessary. Hold the board on the edge, do not try to bend or ex the board.

• Do not leave any unfastened small parts inside the case aer installaon. Loose parts

will cause short circuits which may damage the equipment.

• Keep the computer from dangerous area, such as heat source, humid air and water.

• The operang temperatures of the computer should be 0 to 45 degrees Celsius.

• To avoid injury, be careful of:

Sharp pins on headers and connectors Rough edges and sharp corners on the chassis Damage to wires that could cause a short circuit

Note

» »The package contents may be dierent due to the sales region or models in which it was sold. For

more informaon about the standard package in your region, please contact your dealer or sales representave.

Chapter 1: Introducon | 3

Page 4

BIH11-AHA User’s Manual

1.2 Specifications

CPU

Chipset Intel H110/ Intel H170 Express Chipset

Graphic

Main Memory

SATA

LAN

Sound Codec Realtek ALC892 Audio codec on board (Line-out Port )

Expansion Slots

Back Panel I/O

On Board Connectors & Headers

Board Size 305 mm (W) x 220 mm (L), ATX

Operaon Temperature 0°C ~ 60°C

Storage Temperature -20°C ~ 80°C

Relave Humidity 10% ~ 90% (non-condensing)

Other Features

Watchdog Timer Yes (65536 segments)

RoHS Compliant Yes

OS Support

Socket 1151 for Intel® Core i5 / i3 / Penum / Celeron processor Maximum CPU TDP (Thermal Design Power): 65 Wa

Integrated Intel® HD Graphics engine Dual independent displays as below:

- Support D-Sub 15 pin VGA output (Max resoluon is 1920 x 1200 @60Hz)

- DVI

Intel H170: 4x DDR4 2133 MHz DIMM slot, Max Supports up to 64 GB Memory Intel H110: 2x DDR4 2133 MHz DIMM slot, Max Supports up to 32 GB Memory

Intel H170: 5x SATAIII Port with 7 Pin connector and supports 2.5”/3.5” SATA HDD/SSD Intel H110: 3x SATA connector (Built-in PCIex1 bus to SATA Bridge ASM1061 support 2x SATAII port)

Intel I210-AT / Intel I219-V 10 / 100 / 1000 Mb/s auto negoaon, Half / Full duplex capability

Intel H170:

1x PCI-E 3.0 x16 Slot 1x PCI-E 3.0 x4 Slot (x4)

1x PCI-E 3.0 x1 Slot 4x PCI Slot (Built-in IT8892 PCIE to PCI Bridge)

1x M.2 Slot: Support SATAIII (6.0 Gb/s) SSD

1x PS/2 Keyboard

1x VGA port (D-sub 15 pin) 1x DVI-D port

4x USB 2.0 Port 2x USB 3.0 Port

2x COM (1 x RS-232/ 1 x RS232/RS422/RS485(oponal), 5V/12V)

2x LAN port

3x Audio Jack (Line-in/ Line-out / Mic)

1x 2*10 pins, 2.54 pitch TPM 1.2 box-header

1x 2*5 pins, 2.54 pitch front panel header 1x 2*5 pins, 2.54 pitch Digital I/O connector

1x 2*5 pins, 2.54 pitch front audio (Line-out & Mic-in)

5x 1*7 pins, SATAIII connector supports 2.5”/ 3.5” SATA HDD/SSD 1x M.2 KEY socket for 2242,2260,2280 SATA SSD

1x 2*13 pins, 2.54 pitch Parallel port box-header

1x 2*5 pins, 2.54 pitch 2 USB 2.0 ports wafer connector 1x 2*10 pins, 2.0 pitch 2 USB 3.0 ports wafer connector

4x 2*5 pins, 4 COM box-header (4x RS-232 with jumper select for 5V/12V @ pin 10) 1x 1*4 pins, CPU PWM-Smart Fan header 2x 1*3 pins, system DC-Fan header

1x 24 pins, ATX power connector

1x 2*2 pins, 12V power connector

1 x Buzzer

Wake on RPL/PXE LAN boot ROM ACPI/APM Power loss recovery S3 (enable / disable by BIOS) Eup : S5 <0.5W

Windows 7 32/64bits, Windows 8.1 64bits,Windows 10 64bits

We reserve the right to add or remove support for any OS with or without noce.

Intel H110:

1x PCI-E 3.0 x16 Slot 1x PCI-E 2.0 x4 Slot (x1) - Support 1x PCIE

1x PCI-E 2.0 x1 Slot 4x PCI Slot (Built-in IT8892 PCIE to PCI Bridge)

1x M.2 Slot: Support SATAIII (6.0 Gb/s) SSD

4 | Chapter 1: Introducon

Page 5

1�3 Rear Panel Connectors

COM1: Serial port Connectors (RS-232/RS422/RS485)

RS-232 (Default) RS-422* RS-485*

Pin Assignment

1 Carrier detect (DCD) 422 TXD- 485 DATA-

COM2: Serial Port Connectors (RS-232)

2 Received data (RXD) 422 TXD+ 485 DATA+

3 Transmied data (TXD) 422 RXD+ NC

4 Data terminal ready (DTR) 422 RXD- NC

5 Signal ground (GND) GND GND

6 Data set ready (DSR) NC NC

7 Request to send (RTS) NC NC

8 Clear to send (CTS) NC NC

*RI, 5V, 12V selected by

(selected by JP1 seng)

Pin Assignment Pin Assignment

1 DCD 2 RXD

3 TXD 4 DTR

5 GND 6 DSR

7 RTS 8 CTS

9 *RI, 5V, 12V selected by (selected by JP2 seng)

BIH11-AHA User’s Manual

NC NC

Note

» »COM1/2 voltage selecon is controlled by JP1/ JP2 setup. » »COM1 (RS-232/422/485) & COM2 (RS-232) selecon is controlled by JSEL1/JSEL2.

Chapter 1: Introducon | 5

Page 6

BIH11-AHA User’s Manual

1.4 Motherboard Layout

Note

» » represents the 1st pin.

6 | Chapter 1: Introducon

Page 7

BIH11-AHA User’s Manual

Chapter 2: Hardware installaon

2.1 Central Processing Unit (CPU)

Step 1: Locate the CPU socket on the motherboard

Note

» »Remove Pin Cap before installaon, and make good preservaon for future use. When the CPU is

removed, cover the Pin Cap on the empty socket to ensure pin legs won’t be damaged.

» »The motherboard might equip with two dierent types of pin cap. Please refer below instrucon to

remove the pin cap.

Step 2: Pull the socket locking lever out from the socket and then raise the lever up.

Step 3: Remove the Pin Cap.

Chapter 2: Hardware installaon | 7

Page 8

BIH11-AHA User’s Manual

Step 4: Hold processor with your thumb and index ngers, oriented as shown. Align the notches with the socket. Lower the processor straight down without lng or sliding the

processor in the socket.

Note

» »Ensure that you install the correct CPU designed for LGA1151 socket. » »The CPU ts only in one correct orientaon. Do not force the CPU into the socket to prevent

damaging the CPU.

Step 5: Hold the CPU down rmly, and then lower the lever to locked posion to complete the installaon.

8 | Chapter 2: Hardware installaon

Page 9

BIH11-AHA User’s Manual

2.2 Install a Heatsink

Step 1: Place the CPU fan assembly on top of the installed CPU and make sure that the four fasteners match the motherboard holes. Orient the assembly and make the fan cable is closest to the CPU fan connector.

Step 2: Press down two fasteners at one me in a diagonal sequence to secure the CPU fan

assembly in place. Ensure that all four fasteners are secured.

Note

» »Do not forget to connect the CPU fan connector. » »For proper installaon, please kindly refer to the installaon manual of your CPU heatsink.

Chapter 2: Hardware installaon | 9

Page 10

BIH11-AHA User’s Manual

2.3 Connect Cooling Fans

These fan headers support cooling-fans built in the computer. The fan cable and connector may be dierent according to the fan manufacturer. Connect the fan cable to the connector

while matching the black wire to pin#1.

CPU_FAN1: CPU fan header

Pin Assignment

1 Ground

2 +12V

3 FAN RPM rate sense

4 Smart Fan Control (By Fan)

SYS_FAN1/2: System fan header

Pin Assignment

1 Ground

2 +12V

3 FAN RPM rate sense

Note

» »System Fan Headers support 3-pin head connectors. When connecng with wires onto connectors,

please note that the red wire is the posive and should be connected to pin#2, and the black wire is Ground and should be connected to GND.

2.4 Installing System Memory

DDR4 Modules

10 | Chapter 2: Hardware installaon

Page 11

BIH11-AHA User’s Manual

Step 1: Unlock a DIMM slot by pressing the retaining clips outward. Align a DIMM on the slot such that the notch on the DIMM matches the break on the slot.

Step 2: Insert the DIMM vercally and rmly into the slot unl the retaining clips snap back in

place and the DIMM is properly seated.

Note

» If the DIMM does not go in smoothly, do not force it. Pull it all the way out and try again.

Memory Capacity

DIMM Socket Locaon DDR4 Module Total Memory Size

DIMMA1 4GB/8GB/16GB DIMMA2 4GB/8GB/16GB DIMMB1 4GB/8GB/16GB DIMMB2 4GB/8GB/16GB

Note

» »When installing more than one memory module, we recommend to use the same brand and

capacity memory on this motherboard.

Max is 64GB.

Chapter 2: Hardware installaon | 11

Page 12

BIH11-AHA User’s Manual

2.5 Expansion Slots

PEX16_1: PCI-Express x16 Slot (x16 speed)

• PCI-Express 3.0 compliant.

• Theorecal maximum bandwidth using two slots simultaneously is 16GB/s for each slot,

a total of 32GB/s.

PEX1_1: PCI-Express x1 Slot

• Intel H170: ▪ PCI-Express 3.0 compliant. ▪ Data transfer bandwidth up to 1GB/s per direcon; 2GB/s in total.

• Intel H110: ▪ PCI-Express 2.0 compliant. ▪ Data transfer bandwidth up to 500MB/s per direcon; 1GB/s in total.

PEX4_1: PCI-Express x4 Slot

• Intel H170 (x4 speed): ▪ PCI-Express 3.0 compliant. ▪ Data transfer bandwidth up to 2GB/s per direcon; 4GB/s in total.

• Intel H110 (x1 speed): ▪ PCI-Express 2.0 compliant. ▪ Data transfer bandwidth up to 500MB/s per direcon; 1GB/s in total.

PCI_1/2/3/4: Peripheral Component Interconnect Slots

The PCI slots support cards used in PCs include: LAN cards, sound cards, modems, TV

tuner cards and other cards that comply with PCI standard.

12 | Chapter 2: Hardware installaon

Page 13

BIH11-AHA User’s Manual

PCIE-M2_1: M.2 (Key M) Slot

• The M.2 slot supports M.2 Type 2242/2260/2280 SSD module. When installing M.2 SSD module, please place the screw and hex pillar to correct posion.

• Support M.2 SATA III (6.0 Gb/s) module.

2.6 Jumper & Switch Setting

Jumper Seng

The illustraon shows how to set up jumpers. When the jumper cap is placed on pins, the

jumper is “close”, if not, that means the jumper is “open”.

Pin opened Pin closed Pin 1-2 closed

JCMOS1: Clear CMOS Jumper

Placing the jumper on pin2-3 allows user to restore the BIOS safe seng and the CMOS data.

Please carefully follow the procedures to avoid damaging the motherboard.

Pin 1-2 Close: Normal Operaon (Default)

Pin 2-3 Close: Clear CMOS data

Clear CMOS Procedures:

1. Remove AC power line.

2. Set the jumper to “Pin 2-3 close”.

3. Wait for ve seconds.

4. Set the jumper to “Pin 1-2 close”.

5. Power on the AC.

6. Reset your desired password or clear the CMOS data.

Chapter 2: Hardware installaon | 13

Page 14

BIH11-AHA User’s Manual

2.7 Headers & Connectors

ATXPWR1: ATX Power Source Connector

For beer compability, we recommend to use a standard ATX 24-pin power supply for this connector. Make sure to nd the correct orientaon before plugging the connector.

Pin Assignment Pin Assignment 13 +3.3V 1 +3.3V 14 -12V 2 +3.3V 15 Ground 3 Ground 16 PS_ON 4 +5V 17 Ground 5 Ground 18 Ground 6 +5V 19 Ground 7 Ground 20 NC 8 PW_OK 21 +5V 9 Standby Voltage+5V 22 +5V 10 +12V 23 +5V 11 +12V 24 Ground 12 +3.3V

ATXPWR2: ATX Power Source Connector

The connector provides +12V to the CPU power circuit.

Pin Assignment

1 +12V

2 +12V

3 Ground

4 Ground

JPANEL1: Front Panel Header

This connector includes Power-on, Reset, HDD LED and Power LED connecons. It allows user to connect the PC case’s front panel switch funcons.

Pin Assignment Funcon Pin Assignment Funcon

14 | Chapter 2: Hardware installaon

1 N/A N/A 2

3 SATA_LED (+)

5 SATA LED (-) 6 Power LED (-)

7 Ground

9 Reset Control 10 Ground

HDD LED

Reset

Buon

Power LED (+)

8 Power Buon

Power LED

Power-On Buon

Page 15

BIH11-AHA User’s Manual

JDIO1: Digital I/O Connector

This connector oers digital I/O funcons and address is set in BIOS.

Pin Assignment

1 VCC5

2 DI1

3 DO1

4 DI2

5 DO2

6 DI3

7 DO3

8 DI4

9 DO4

10 GND

TPM1: Trusted Plaorm Module Header

This header allows you to store cryptographic keys that protect informaon.

Pin Assignment Pin Assignment

1 PCLK_TPM 2 GND

3 L_FRAME_N 4 N/A

5 PCIERST2 6 VCC5

7 LAD3 8 LAD2

9 VCC3_3 10 LAD1

11 LAD0 12 GND

13 SMB_CLK 14

15 +3V3_DUAL 16 SER_IRQ

17 GND 18 CLK_RUN#

19 SUS_STAT_N 20 LDRQJ1

SMB_DATA_ RESUME

SATA3_1/2/3/4/5: Serial ATA 3.0 Gb/s Connectors (1*7 Pin)

The connector supports the thin Serial ATA cable for primary internal storage devices.

Pin Assignment

1 GND

2 TX+

3 TX-

4 GND

5 RX-

6 RX+

7 GND

Chapter 2: Hardware installaon | 15

Page 16

BIH11-AHA User’s Manual

JFRONT_USB3_1: Header for USB 3.0 Ports at Front Panel

This header allows user to add addional USB ports on the PC front panel, and also can be

connected with a wide range of external peripherals.

Pin Assignment Pin Assignment

1 VBUS0 11 D2+

2 SSRX1- 12 D2-

3 SSRX1+ 13 Ground

4 Ground 14 SSTX2+

5 SSTX1- 15 SSTX2-

6 SSTX1+ 16 Ground

7 Ground 17 SSRX2+

8 D1- 18 SSRX2-

9 D1+ 19 VBUS1

10 ID 20 Key

F_USB1: USB 2.0 Header

The mainboard provides USB 2.0 pin header. Each header allows you to connect 2 addional

USB 2.0 ports.

Pin Assignment Pin Assignment

1 +5V(fused) 2 +5V(fused)

3 USB - 4 USB -

5 USB + 6 USB +

7 Ground 8 Ground

F_AUDIO1: Front Panel Audio Header

This header allows user to connect the chassis-mount front panel audio I/O which supports HD

and AC’97 audio standards.

HD Audio AC’97

Pin Assignment Pin Assignment

1 Mic Le in 1 Mic In

2 Ground 2 Ground

3 Mic Right in 3 Mic Power

4 GPIO 4 Audio Power

5 Right line in 5 RT Line Out

6 Jack Sense 6 RT Line Out

7 Front Sense 7 Reserved

8 Key 8 Key

9 Le line in 9 LFT Line Out

10 Jack Sense 10 LFT Line Out

16 | Chapter 2: Hardware installaon

Page 17

BIH11-AHA User’s Manual

J_PRINT1: Printer Port Connector

This header allows you to connector printer on the PC.

Pin Assignment Pin Assignment

1 -Strobe 14 Ground

2 -ALF 15 Data 6

3 Data 0 16 Ground

4 -Error 17 Data 7

5 Data 1 18 Ground

6 -Init 19 -ACK

7 Data 2 20 Ground

8 -Scln 21 Busy

9 Data 3 22 Ground

10 Ground 23 PE

11 Data 4 24 Ground

12 Ground 25 SCLT

13 Data 5 26 Key

JSEL1/JSEL2: RS-232/422/485 Switch Headers for COM1

The headers determine that COM1 belongs to RS-232 (Default), 422, or 485.

JSEL1(JCOM1A)

RS-232 RS-422 RS-485

1-3 (Default) 3-5 3-5

2-4 (Default) 4-6 4-6

7-9 (Default) 9-11 9-11

8-10 (Default) 10-12 10-12

JSEL2(JCOM1A)

1-2 (Default) RS-232

3-4 RS-422

5-6 RS-485

JCOM1: Serial Port Headers

Pin Assignment Pin Assignment

1 DCD 2 RXD

3 TXD 4 DTR

5 GND 6 DSR

7 RTS 8 CTS

9 COM_RI_PWR 10 NA

Chapter 2: Hardware installaon | 17

Page 18

BIH11-AHA User’s Manual

JP1/2/3/4/5/6: Serial Port Voltage Switch Jumper for JCOM1/2/3/4/5/6

Pin 1-2 Close: Pin9=Ring(Default)

Pin 3-4 Close: 5V

Pin 5-6 Close: 12V

18 | Chapter 2: Hardware installaon