Biostar A960G+ Owner's Manual

Page 1
A960G+/A960GL+ Setup Manual
FCC Information and Copyright
This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. There is no guarantee that interference will not occur in a particular installation.
The vendor makes no representations or warranties with respect to the contents here and specially disclaims any implied warranties of merchantability or fitness for any purpose. Further the vendor reserves the right to revise this publication and to make changes to the contents here without obligation to notify any party beforehand.
Duplication of this publication, in part or in whole, is not allowed without first obtaining the vendor’s approval in writing.
The content of this user’s manual is subject to be changed without notice and we will not be responsible for any mistakes found in this user’s manual. All the brand and product names are trademarks of their respective companies.
Dichiarazione di conformità sintetica
Ai sensi dell’art. 2 comma 3 del D.M. 275 del 30/10/2002
Si dichiara che questo prodotto è conforme alle normative vigenti e soddisfa i requisiti essenziali richiesti dalle direttive
2004/108/CE, 2006/95/CE e 1999/05/CE
quando ad esso applicabili
Short Declaration of conformity
We declare this product is complying with the laws in force and meeting all the essential requirements as specified by the directives
2004/108/CE, 2006/95/CE and 1999/05/CE
whenever these laws may be applied
Page 2
Table of Contents
Chapter 1: Introduction.......................................... 1
1.1 Before You Start ................................................................................1
1.2 Package Checklist.............................................................................1
1.3 Motherboard Features...................................................................... 2
1.4 Rear Panel Connectors ..................................................................... 3
1.5 Motherboard Layout ........................................................................4
Chapter 2: Hardware Installation ........................... 5
2.1 Installing Central Processing Unit (CPU) ....................................... 5
2.2 FAN Headers......................................................................................7
2.3 Installing System Memory ................................................................8
2.4 Connectors and Slots ....................................................................... 10
Chapter 3: Headers & Jumpers Setup.................... 13
3.1 How to Setup Jumpers ....................................................................13
3.2 Detail Settings.................................................................................. 13
Chapter 4: RAID Functions ................................... 17
4.1 Operating System............................................................................ 17
4.2 Raid Arrays......................................................................................17
4.3 How RAID Works.............................................................................17
Chapter 5: Useful Help ......................................... 20
5.1 Driver Installation Note .................................................................20
5.2 Software............................................................................................ 21
5.3 Extra Information ...........................................................................25
5.4 Troubleshooting...............................................................................27
Appendix: SPEC In Other Languages .................... 28
German .................................................................................................................28
French....................................................................................................................30
Italian.................................................................................................................... 32
Spanish ..................................................................................................................34
Portuguese............................................................................................................36
Polish .....................................................................................................................38
Russian ..................................................................................................................40
Arabic .................................................................................................................... 42
Japanese................................................................................................................ 44
Page 3
CHAPTER 1: INTRODUCTION
A960G+/A960GL+
1.1 B
EFORE YOU START
Thank you for choosing our product. Before you start installing the motherboard, please make sure you follow the instructions below:
Prepare a dry and stable working environment with
sufficient lighting.
Always disconnect the computer from power outlet
before operation.
Before you take the motherboard out from anti-static
bag, ground yourself properly by touching any safely grounded appliance, or use grounded wrist strap to remove the static charge.
Avoid touching the components on motherboard or the
rear side of the board unless necessary. Hold the board on the edge, do not try to bend or flex the board.
Do not leave any unfastened small parts inside the
case after installation. Loose parts will cause short circuits which may damage the equipment.
Keep the computer from dangerous area, such as heat
source, humid air and water.
1.2 PACKAGE CHECKLIST
Serial ATA Cable X 2 Rear I/O Panel for ATX Case X 1 Installation Guide X 1 Fully Setup Driver DVD X 1 (full version manual files inside) USB 2.0 Cable X1 (optional) Serial ATA Power Cable X 1 (optional)
Note: The package contents may be different due to area or your motherboard version.
1
Page 4
Motherboard Manual
1.3 MOTHERBOARD FEATURES
SPEC
CPU
FSB
Chipset
Super I/O
Main
Memory
Graphics
SATA II
Socket AM3 / AM3+
AMD Sempron/Athlon II / Phenom II /FX
processors (Maximum Watt: 95W)
Support Hyper Transport 3.0
Supports up to 4.4 GT/s Bandwidth
AMD 760G
AMD SB710
ITE 8728
Provides the most commonly used
legacy Super I/O functionality
DDR3 DIMM Slots x 2
Max Memory Capacity 16GB
Each DIMM supports 512MB/1GB/
2GB/4GB/8GB DDR3
Integrated in AMD 760G Chipset Max Shared Video Memory is 512MB
Integrated Serial ATA Controller
AMD 64 Architecture enables 32 and 64 bit computing
Supports Hyper Transport 3.0
Low Pin Count Interface
Environment Control initiatives
H/W Monitor
ITE's "Smart Guardian" function
Dual Channel Mode DDR3 memory module
Supports DDR3 800/1066/1333/1600(OC)/1866(OC
for AM3+ CPU only)
Registered DIMM and ECC DIMM is not supported
Data transfer rates up to 3 Gb/s
SATA Version 2.0 specification compliant
LAN
Sound
Slots
On Board
Connectors
2
Realtek RTL 8111F (A960G+)
Realtek RTL 8105E (A960GL+)
ALC662
PCI Express X16 slot x1 Supports PCI-E X16 expansion card
PCI slot x1 Supports PCI expansion cards
SATA Connector x4 Each connector supports 1 SATA device
Front Panel Connector x1 Supports front panel facilities
Front Audio Connector x1 Supports front panel audio function
CPU Fan Header x1 CPU Fan power supply (with Smart Fan function)
10 / 100 / 1000 Mb/s auto negotiation
10 / 100 Mb/s auto negotiation
5.1 channels audio out
High Definition Audio
Page 5
A960G+/A960GL+
SPEC
System Fan Header x1 System Fan Power supply
CMOS Clear Jumper x1 Restore CMOS data to factory default setting
USB Connector x2 Each connector supports 2 front panel USB ports
Power Connector (24pin) x1 Connects to Power supply
Power Connector (4pin) x1 Connects to Power supply
Printer Port Connector x1 Each connector supports 1 Printer port
PS/2 Keyboard x1
PS/2 Mouse x1
Back Panel
I/O
Board Size
Special
Features
OS Support
VGA port x1
LAN port x1
USB Port x4
Audio Jack x3
182 mm(W) x 225 mm(L)
RAID 0 / 1 / 10 support
Windows XP / Vista / 7
1.4 REAR PANEL CONNECTORS
PS/2 Mouse
Connects to PS/2 Keyboard
Connects to PS/2 Mouse
Connect to D-SUB monitor
Connect to RJ-45 Ethernet cable
Connect to USB devices
Provide Audio-In/Out and microphone connection
Biostar reserves the right to add or remove support for
any OS With or without notice.
LAN
Line In/ Surround
Line Out
Mic In 1/ Bass/ Center
PS/2
VGA
USBX2USBX2
Keyboard
3
Page 6
Motherboard Manual
1.5 MOTHERBOARD LAYOUT
4
Note: represents the 1
st
pin.
Page 7
A960G+/A960GL+
CHAPTER 2: HARDWARE INSTALLATION
2.1 I
NSTALLING CENTRAL PROCESSING UNIT (CPU)
Step 1: Pull the lever toward direction A from the socket and then raise the
lever up to a 90-degree angle.
Step 2: Look for the white triangle on socket, and the gold triangle on
CPU should point towards this white triangle. The CPU will fit only in the correct orientation.
5
Page 8
Motherboard Manual
Step 3: Hold the CPU down firmly, and then close the lever toward direct
B to complete the installation.
Step 4: Put the CPU Fan on the CPU and buckle it. Connect the CPU
FAN power cable to the CPU_FAN1. This completes the installation.
Note:
1. This MB is designed for AMD 95W AM3/AM3+ CPU, pleases check the CPU TDP spec before you install it on MB AM3+ CPU TDP spec from below weblink:
http://www.amd.com/us/products/desktop/processors/amdfx/Pages/amdfx-model­number-comparison.aspx
2. AMD’s product warranty does not cover damage caused by overclocking (even when overclocking is enabled via AMD OverDrive software).
http://www.amd.com/us/products/desktop/processors/amdfx/Pages/amdfx.aspx
3. Due to the AMD AM3+ CPU designation, we strongly recommend you use AMD original box CPU fan and add an extra system fan inside the chassis.
6
Page 9
A960G+/A960GL+
2.2 FAN HEADERS
These fan headers support cooling-fans built in the computer. The fan cable and connector may be different due to the fan manufacturer. Connect the fan cable to the connector while matching the black wire to pin#1.
CPU_FAN1: CPU Fan Header
Pin
Assignment
1 Ground 2 +12V 3
FAN RPM rate sense
4 Smart Fan Control
(By Fan)
SYS_FAN1: System Fan Header
Pin
Assignment
1 Ground 2 +12V 3 FAN RPM rate sense
Note:
The CPU_FAN1 supports 4-pin head connector. The SYS_FAN1 supports 3-pin head connector. When connecting with wires onto connectors, please note that the red wire is the positive and should be connected to pin#2, and the black wire is Ground and should be connected to GND.
7
Page 10
Motherboard Manual
2.3 INSTALLING SYSTEM MEMORY
A. Memory Modules
1. Unlock a DIMM slot by pressing the retaining clips outward. Align a DIMM on the slot such that the notch on the DIMM matches the break on the Slot.
8
Page 11
A960G+/A960GL+
2. Insert the DIMM vertically and firmly into the slot until the retaining chip snap back in place and the DIMM is properly seated.
Note:
If the DIMM does not go in smoothly, do not force it. Pull it all the way out and try again.
B. Memory Capacity
DIMM Socket
Location
DDR3_A1 512MB/1GB/2GB/4GB/8GB
DDR3_B1 512MB/1GB/2GB/4GB/8GB
DDR3 Module
Total Memory
Size
Max is 16GB.
C. Dual Channel Memory installation
Please refer to the following requirements to activate Dual Channel function:
Install memory module of the same density in pairs, shown in the table.
Dual Channel Status
Disabled O X
Disabled X O
Enabled O O
(O means memory installed, X means memory not installed.)
The DRAM bus width of the memory module must be the same (x8 or x16)
DDR3_A1
DDR3_B1
9
Page 12
Motherboard Manual
2.4 CONNECTORS AND SLOTS
SATA1~SATA4: Serial ATA Connectors
The motherboard has a PCI to SATA Controller with 4channels SATA interface, it satisfies the SATA 2.0 spec and with transfer rate of 3Gb/s.
ATXPWR2: ATX Power Source Connector
This connector provides +12V to CPU power circuit.
Pin Assignment
1 Ground 2 TX+ 3 TX­4 Ground 5 RX­6 RX+ 7 Ground
10
Pin Assignment
1 +12V 2 +12V 3 Ground 4 Ground
Page 13
ATXPWR1: ATX Power Source Connector
This connector allows user to connect 24-pin power connector on the ATX power supply.
Pin Assignment Pin Assignment
13 +3.3V 1 +3.3V 14 -12V 2 +3.3V 15 Ground 3 Ground 16 PS_ON 4 +5V 17 Ground 5 Ground 18 Ground 6 +5V 19 Ground 7 Ground 20 NC 8 PW_OK 21 +5V 9 Standby Voltage+5V 22 +5V 10 +12V 23 +5V 11 +12V 24 Ground 12 +3.3V
Note:
Before power on the system, please make sure that both ATXPWR1 and ATXPWR2 connectors have been plugged-in.
A960G+/A960GL+
11
Page 14
Motherboard Manual
PEX16_1: PCI-Express X16 Slot
- PCI-Express 2.0 compliant.
- Maximum theoretical realized bandwidth of 4GB/s simultaneously per
direction, for an aggregate of 8GB/s totally.
- PCI-Express supports a raw bit-rate of 2.5Gb/s on the data pins.
PCI1: Peripheral Component Interconnect Slot
This motherboard is equipped with 1 standard PCI slot. PCI stands for Peripheral Component Interconnect, and it is a bus standard for expansion cards. This PCI slot is designated as 32 bits.
12
Page 15
A960G+/A960GL+
CHAPTER 3: HEADERS & JUMPERS SETUP
3.1 H
OW TO SETUP JUMPERS
The illustration shows how to set up jumpers. When the jumper cap is placed on pins, the jumper is “close”, if not, that means the jumper is “open”.
Pin opened Pin closed Pin1-2 closed
3.2 DETAIL SETTINGS
PANEL1: Front Panel Header
This 16-pin connector includes Power-on, Reset, HDD LED, Power LED, and speaker connection. It allows user to connect the PC case’s front panel switch functions.
Pin Assignment Function Pin Assignment Function
1 +5V 9 N/A 2N/A 10N/A 3 N/A 11 N/A N/A 4 Speaker 5 HDD LED (+) 13 Power LED (+) 6 HDD LED (-) 7 Ground 15 Power button 8 Reset control
Speaker Connector
Hard drive LED
Reset button
12 Power LED (+)
14 Power LED (-)
16 Ground
N/A
Power LED
Power-on button
13
Page 16
Motherboard Manual
F_USB1/F_USB2: Headers for USB 2.0 Ports at Front Panel
These headers allow user to connect additional USB cable on the PC front panel, and also can be connected with internal USB devices, like USB card reader.
F_AUDIO1: Front Panel Audio Header
This header allows user to connect the front audio output cable with the PC front panel. This header allows only HD audio front panel connector; AC’97 connector is not acceptable.
Assignment
Pin
1 +5V (fused) 2 +5V (fused) 3 USB­4 USB­5 USB+ 6 USB+ 7 Ground 8 Ground 9 NC
10 Key
Pin Assignment
1 Mic Left in 2 Ground 3 Mic Right in 4 GPIO 5 Right line in 6 Jack Sense 7 Front Sense 8 Key 9 Left line in
10 Jack Sense
14
Page 17
J_PRINT1: Printer Port Connector
This header allows you to connector printer on the PC.
Pin Assignment Pin Assignment
1 -Strobe 14 Ground 2 -ALF 15 Data 6 3 Data 0 16 Ground 4 -Error 17 Data 7 5 Data 1 18 Ground 6 -Init 19 -ACK 7 Data 2 20 Ground 8 -Scltin 21 Busy
9 Data 3 22 Ground 10 Ground 23 PE 11 Data 4 24 Ground 12 Ground 25 SCLT 13 Data 5 26 Key
A960G+/A960GL+
15
Page 18
Motherboard Manual
JCMOS1: Clear CMOS Jumper
Placing the jumper on pin2-3 allows user to restore BIOS safe setting and CMOS data. Pease carefully follow the procedures to avoid damaging the motherboard.
Clear CMOS Procedures:
1. Remove AC power line.
2. Set the jumper to “Pin 2-3 close”.
3. Wait for five seconds.
4. Set the jumper to “Pin 1-2 close”.
5. Power on the AC.
6. Load Optimal Defaults and save settings in CMOS.
13
Pin 1-2 Close:
Normal Operation (default).
13
Pin 2-3 Close:
Clear CMOS data.
16
Page 19
CHAPTER 4: RAID FUNCTIONS
A960G+/A960GL+
4.1 O
z Supports Windows XP, Windows Vista, and Windows 7.
PERATING SYSTEM
4.2 RAID ARRAYS
RAID supports the following types of RAID arrays:
RAID 0: RAID 0 defines a disk striping scheme that improves disk read and write times for
many applications.
RAID 1: RAID 1 defines techniques for mirroring data. RAID 10: RAID 10 combines the techniques used in RAID 0 and RAID 1.
4.3 HOW RAID WORKS
RAID 0:
The controller “stripes” data across multiple drives in a RAID 0 array system. It breaks up a large file into smaller blocks and performs disk reads and writes across multiple drives in parallel. The size of each block is determined by the stripe size parameter, which you set during the creation of the RAID set based on the system environment. This technique reduces overall disk access time and offers high bandwidth.
Features and Benefits
- Drives: Minimum 1, and maximum is up to 6 or 8. Depending on the platform.
- Uses: Intended for non-critical data requiring high data throughput, or any environment that does not require fault tolerance.
- Benefits: provides increased data throughput, especially for large files. No capcity loss penalty for parity.
- Drawbacks: Does not deliver any fault tolerance. If any drive in the array fails, all data is lost.
- Fault Tolerance: No.
Block 1 Block 3 Block 5
Block 2 Block 4 Block 6
17
Page 20
Motherboard Manual
RAID 1:
Every read and write is actually carried out in parallel across 2 disk drives in a RAID 1 array system. The mirrored (backup) copy of the data can reside on the same disk or on a second redundant drive in the array. RAID 1 provides a hot-standby copy of data if the active volume or drive is corrupted or becomes unavailable because of a hardware failure.
RAID techniques can be applied for high-availability solutions, or as a form of automatic backup that eliminates tedious manual backups to more expensive and less reliable media.
Features and Benefits
- Drives: Minimum 2, and maximum is 2.
- Uses: RAID 1 is ideal for small databases or any other application that
requires fault tolerance and minimal capacity.
- Benefits: Provides 100% data redundancy. Should one drive fail, the controller switches to the other drive.
- Drawbacks: Requires 2 drives for the storage space of one drive. Performance is impaired during drive rebuilds.
- Fault Tolerance: Yes.
18
Block 1 Block 2 Block 3
Block 1 Block 2 Block 3
Page 21
A960G+/A960GL+
RAID 10:
RAID 1 drives can be stripped using RAID 0 techniques. Resulting in a RAID 10 solution for improved resiliency, performance and rebuild performance.
Features and Benefits
- Drives: Minimum 4, and maximum is 6 or 8, depending on the platform.
- Benefits: Optimizes for both fault tolerance and performance, allowing for
automatic redundancy. May be simultaneously used with other RAID levels in an array, and allows for spare disks.
- Drawbacks: Requires twice the available disk space for data redundancy, the same as RAID level 1.
- Fault Tolerance: Yes.
Block 1 Block 3 Block 5
Block 1 Block 3 Block 5
Block 2 Block 4 Block 6
Block 2 Block 4 Block 6
19
Page 22
Motherboard Manual
CHAPTER 5: USEFUL HELP
5.1 D
RIVER INSTALLATION NOTE
After you installed your operating system, please insert the Fully Setup Driver DVD into your optical drive and install the driver for better system performance.
You will see the following window after you insert the DVD
The setup guide will auto detect your motherboard and operating system.
Note:
If this window didn’t show up after you insert the Driver DVD, please use file browser to locate and execute the file SETUP.EXE under your optical drive.
A. Driver Installation
To install the driver, please click on the Driver icon. The setup guide will list the compatible driver for your motherboard and operating system. Click on each device driver to launch the installation program.
B. Software Installation
To install the software, please click on the Software icon. The setup guide will list the software available for your system, click on each software title to launch the installation program.
C. Manual
Aside from the paperback manual, we also provide manual in the Driver DVD. Click on the Manual icon to browse for available manual.
Note:
You will need Acrobat Reader to open the manual file. Please download the latest version of Acrobat Reader software from http://www.adobe.com/products/acrobat/readstep2.html
20
Page 23
A960G+/A960GL+
5.2 SOFTWARE
Installing Software
1. Insert the Setup DVD to the optical drive. The drivers installation program would appear if the Autorun function has been enabled.
2. Select Software Installation, and then click on the respective software title.
3. Follow the on-screen instructions to complete the installation.
Launching Software
After the installation process, you will see the software icon “eHOT Line” / “BIOS Update” appears on the desktop. Double-click the icon to launch the utility.
eHot-Line (Optional)
eHot-Line is a convenient utility that helps you to contact with our Tech-Support system. This utility will collect the system information which is useful for analyzing the problem you may have encountered, and then send these information to our tech-support department to help you fix the problem.
Before you use this utility, please set Outlook Express as your default e-mail client application program.
represent s important
*
in forma tion t hat y ou must provide. Without this information, you may not be able to send out the mail.
This block will show th e info rmat ion whic h wou ld be c ol lec ted i n the mail.
Describe condition
*
of your system.
Send the mail out .
Sav e th ese in for mat io n to a .txt fil e
Exit this dialog .
Select your area or
*
the area close to you.
Provi de t he e-ma il address that you would like to send the copy to.
Provi de t he nam e of
*
the memory module manufact urer.
Provi de th e name of the power supply manufacturer and the model no.
21
Page 24
Motherboard Manual
After filling up this information, click “Send” to send the mail out. A warning dialog would appear asking for your confirmation; click “Send” to confirm or “Do Not Send” to cancel.
If you want to save this information to a .txt file, click “Save As…” and then you will see a saving dialog appears asking you to enter file name.
Enter the file name and then click “Save”. Your system information will be saved to a .txt file.
22
Open the saved .txt file, you will see your system information including motherboard/BIOS/CPU/video/ device/OS information. This information is also concluded in the sent mail.
We will not share customer’s data with any other third parties, so please feel free to provide your system information while using eHot-Line service.
If you are not using Outlook Express as your default e-mail client application, you may need to save the system information to a .txt file and send the file to our tech support with other e-mail application. Go to the following web
http://www.biostar.com.tw/app/en-us/about/contact.php
for getting
our contact information.
Page 25
A960G+/A960GL+
e
BIOS Update
BIOS Update is a convenient utility which allows you to update your motherboard BIOS under Windows system.
Show current BIO S informati on
Update BIOS
from the Internet
with a BIOS fil
Update BIOS
Save current BIOS
to a .bin file
<Backup BIOS>
Once click on this button, the saving
dialog will show. Choose the
position to save file and enter file
name. (We recommend that the file
name should be English/number
and no longer than 7 characters.)
Then click Save.
23
Page 26
Motherboard Manual
<Update BIOS>
Before doing this, please download the proper BIOS file from the website.
Then click Update BIOS button, a dialog will show for asking you backup current BIOS. Click Yes for BIOS backup and refer to the Backup BIOS procedure; or click No to skip this procedure.
After the BIOS Backup procedure, the open dialog will show for requesting the BIOS file which is going to be updated. Please choose the proper BIOS file for updating, then click on Open.
The utility will update BIOS with the proper BIOS file, and this process may take minutes. Please do not open any other applications during this process.
After the BIOS Update process, click on OK to restart the system.
While the system boots up and the full screen logo shows, press <Delete> key to enter BIOS setup.
In the BIOS setup, use the Load Optimized Defaults function and then Save and Exit Setup to exit BIOS setup. BIOS Update is completed.
All the information and content above about the software are subject to be changed without notice. For better performance, the software is being continuously updated. The information and pictures described above are for your reference only. The actual information and settings on board may be slightly different from this manual.
24
Page 27
5.3 EXTRA INFORMATION
CPU Overheated
If the system shutdown automatically after power on system for seconds, that means the CPU protection function has been activated.
When the CPU is over heated, the motherboard will shutdown automatically to avoid a damage of the CPU, and the system may not power on again.
In this case, please double check:
1. The CPU cooler surface is placed evenly with the CPU surface.
2. CPU fan is rotated normally.
3. CPU fan speed is fulfilling with the CPU speed.
After confirmed, please follow steps below to relief the CPU protection function.
1. Remove the power cord from power supply for seconds.
2. Wait for seconds.
3. Plug in the power cord and boot up the system.
Or you can:
1. Clear the CMOS data. (See “Close CMOS Header: JCMOS1” section)
2. Wait for seconds.
3. Power on the system again.
A960G+/A960GL+
25
Page 28
Motherboard Manual
BIO-Flasher
BIO-Flasher is a BIOS flashing utility providing you an easy and simple way to update your BIOS via USB pen drive or floppy disk.
The BIO-Flasher is built in the BIOS chip. To enter the utility, press <F12> during the Power-On Self Tests (POST) procedure while booting up.
Updating BIOS with BIO-Flasher
1. Go to the website to download the latest BIOS file for the motherboard.
2. Then, save the BIOS file into a USB pen drive or a floppy disk.
3. Insert the USB pen drive or the floppy disk that contains the BIOS file to the USB port or the floppy disk drive.
4. Power on or reset the computer and then press <F12> during the POST process. A select dialog as the picture on the right appears. Select the device contains the BIOS file and press <Enter> to enter the utility.
26
5. The utility will show the BIOS files and their respective information. Select the proper BIOS file and press <Enter> then <Y> to perform the BIOS update process.
6. After the update process, the utility will ask you to reboot the system. Press <Y> to proceed. BIOS update completes.
z This utility only allows storage device with FAT32/16 format and single
partition.
z Shutting down or resetting the system while updating the BIOS will lead to
system boot failure.
Page 29
5.4 TROUBLESHOOTING
Probable Solution
1. There is no power in the system. Power LED does not shine; the fan of the power supply does not work
2. Indicator light on keyboard does not shine.
System is inoperative. Keyboard lights are on, power indicator lights are lit, and hard drives are running.
System does not boot from a hard disk drive, but can be booted from optical drive.
System only boots from an optical drive. Hard disks can be read, applications can be used, but system fails to boot from a hard disk.
Screen message shows “Invalid Configuration” or “CMOS Failure.”
System cannot boot after user installs a second hard drive.
A960G+/A960GL+
1. Make sure power cable is securely plugged in.
2. Replace cable.
3. Contact technical support.
Using even pressure on both ends of the DIMM, press down firmly until the module snaps into place.
1. Check cable running from disk to disk controller board. Make sure both ends are securely plugged in; check the drive type in the standard CMOS setup.
2. Backing up the hard drive is extremely important. All hard disks are capable of breaking down at any time.
1. Back up data and applications files.
2. Reformat the hard drive. Re-install applications and data using backup disks.
Review system’s equipment. Make sure correct information is in setup.
1. Set master/slave jumpers correctly.
2. Run SETUP program and select correct drive types. Call the drive manufacturers for compatibility with other drives.
27
Page 30
Motherboard Manual
APPENDIX: SPEC IN OTHER LANGUAGES
G
ERMAN
Spezifikationen
CPU
FSB
Chipsatz
Super E/A
Arbeitsspeich
er
Grafik
Sockel AM3 / AM3+
Die AMD 64-Architektur unterstützt eine 32-Bit- und
AMD Sempron/Athlon II / Phenom II
64-Bit-Datenverarbeitung
/FX Prozessoren (Maximales Watt:
Unterstützt Hyper Transport 3.0
95W)
Unterstützt Hyper Transport 3.0 mit
einer Bandbreite von bis zu 4.4 GT/s
AMD 760G
AMD SB710
Low Pin Count-Schnittstelle
ITE8728
Umgebungskontrolle,
Bietet die häufig verwendeten alten
Hardware-Überwachung
Super E/A-Funktionen.
"Smart Guardian"-Funktion von ITE
Dual-Kanal DDR3 Speichermodul
DDR3 DIMM-Steckplätze x 2
Unterstützt DDR3 800/1066/1333/1600(OC)/1800(OC
Max. 16GB Arbeitsspeicher
für AM3-CPU-only)
Jeder DIMM unterstützt 512MB/1GB/
registrierte DIMMs. ECC DIMMs werden nicht
2GB/4GB/8GB DDR3.
unterstützt.
Integrierter AMD 760G-Chipsatz Max. 512MB gemeinsam benutzter Videospeicher
SATA
LAN
HD
Audio-Unters
tützung
Steckplätze
28
Integrierter Serial ATA-Controller
Realtek RTL 8111F (A960G+)
Realtek RTL 8105E (A960GL+)
ALC662
PCI Express X16 Steckplatz x1
PCI-Steckplatz x1
Datentransferrate bis zu 3 Gb/s
Konform mit der SATA-Spezifikation Version 2.0.
10 / 100 / 1000 Mb/s auto negotiation
10 / 100 Mb/s auto negotiation
5.1-Kanal-Audioausgabe
Unterstützt High-Definition Audio
Page 31
A960G+/A960GL+
Spezifikationen
SATA-Anschluss x4 Jeder Anschluss unterstützt 1 SATA-Laufwerk
Fronttafelanschluss x1 Unterstützt die Fronttafelfunktionen
Front-Audioanschluss x1 Unterstützt die Fronttafel-Audioanschlussfunktion
Onboard-Ans
chluss
Rückseiten-E
/A
Platinengröß
e
Sonderfunkti
onen
CPU-Lüfter-Sockel x1
CPU-Lüfterstromversorgungsanschluss (mit Smart
Fan-Funktion)
System-Lüfter-Sockel x1 System-Lüfter-Stromversorgungsanschluss
"CMOS löschen"-Sockel x1
Jeder Anschluss unterstützt 2
USB-Anschluss x2
Fronttafel-USB-Anschlüsse
Stromanschluss (24-polig) x1
Stromanschluss (4-polig) x1
Druckeranschluss Anschluss x1 Jeder Anschluss unterstützt 1 Druckeranschluss
PS/2-Tastatur x1
PS/2-Maus x1
VGA-Anschluss x1
LAN-Anschluss x1
USB-Anschluss x4
Audioanschluss x3
182 mm (B) X 225 mm (L)
Unterstützt RAID 0 / 1 / 10
OS-Unterstü
tzung
Windows XP / Vista / 7
Biostar behält sich das Recht vor, ohne Ankündigung die
Unterstützung für ein Betriebssystem hinzuzufügen
oder zu entfernen.
29
Page 32
Motherboard Manual
FRENCH
Socket AM3 / AM3+
UC
Processeurs AMD Sempron/Athlon II /
Phenom II /FX (Watt maximum : 95W)
SPEC
L'architecture AMD 64 permet le calcul 32 et 64 bits
Prend en charge Hyper Transport 3.0
Bus frontal
Chipset
Super E/S
Mémoire
principale
Graphiques
SATA
Prend en charge Hyper Transport 3.0
jusqu'à une bande passante de 4.4 GT/s
AMD 760G
AMD SB710
ITE 8728
Fournit la fonctionnalité de Super E/S
patrimoniales la plus utilisée.
Fentes DDR3 DI MM x 2
Capacité mémoire maximale de 16Go
Chaque DIMM prend en charge des DDR3
de 512Mo/1Go/2Go/4Go/8Go
Integré dans la chipset AMD 760G Mémoire vidéo partagée maximale de 512 Mo
Contrôleur Serial ATA intégré
Interface à faible compte de broches
Initiatives de contrôle environnementales,
Moniteur de matériel
Fonction "Gardien intelligent" de l'ITE
Module de mémoire DDR3 à mode à double voie
Prend en charge la DDR3
800/1066/1333/1600(OC)/1866(OC pour les
processeurs AM3 uniquement)
Les DIMM à registres et DIMM avec code correcteurs
d'erreurs ne sont pas prises en charge
Taux de transfert jusqu'à 3 Go/s.
Conforme à la spécification SATA Version 2.0
LAN
Prise en
charge
audio HD
Fentes
Connecteur
embarqué
Realtek RTL 8111F (A960G+)
Realtek RTL 8105E (A960GL+)
ALC662
Fente PCI Express X16 x1
Fente PCI x1
Connecteur SATA x4
10 / 100 / 1000 Mb/s négociation automatique
10 / 100 Mb/s négociation automatique
Sortie audio à 5.1 voies
Prise en charge de l'audio haute définition
Chaque connecteur prend en charge 1 périphérique
SATA
30
Page 33
A960G+/A960GL+
SPEC
Connecteur du panneau avant x1 Prend en charge les équipements du panneau avant
Connecteur Audio du panneau avant x1 Prend en charge la fonction audio du panneau avant
E/S du
panneau
arrière
Dimension
s de la
carte
Fonctionnal
ités
spéciales
Support SE
Embase de ventilateur UC x1
Alimentation électrique du ventilateur UC (avec
fonction de ventilateur intelligent)
Embase de ventilateur système x1 Alimentation électrique du ventilateur système
Embase d'effacement CMOS x1
Chaque connecteur prend en charge 2 ports USB de
Connecteur USB x2
panneau avant
Connecteur d'alimentation x1
(24 broches)
Connecteur d'alimentation x1
(4 broches)
Chaque connector prend en charge 1 Port
Connecteur de Port d'imprimante x1
d'imprimante
Clavier PS/2 x1
Souris PS/2 x1
Port VGA x1
Port LAN x1
Port USB x4
Fiche audio x3
182 mm (l) X 225 mm (H)
Prise en charge RAID 0 / 1 / 10
Biostar se réserve le droit d'ajouter ou de supprimer le
Windows XP / Vista / 7
support de SE avec ou sans préavis.
31
Page 34
Motherboard Manual
ITALIAN
SPECIFICA
CPU
FSB
Chipset
Super I/O
Memoria
principale
Grafica
Socket AM3 / AM3+
Processori AMD Sempron/Athlon II /
Phenom II /FX (Watt massimo: 95W)
Supporto di HyperTransport 3.0 fino a
4.4 GT/s di larghezza di banda
AMD 760G
AMD SB710
ITE 8728
Fornisce le funzionalità legacy Super
I/O usate più comunemente.
Alloggi DIMM DDR3 x 2
Capacità massima della memoria 16GB
Ciascun DIMM supporta DDR3
512MB/1GB/2GB/4GB/8GB
Integrata nel Chipset AMD 760G La memoria video condivisa massima è di 512 MB
L’architettura AMD 64 abilita la computazione 32
e 64 bit
Supporto di Hyper Transport 3.0
Interfaccia LPC (Low Pin Count)
Funzioni di controllo dell’ambiente:
Monitoraggio hardware
Funzione "Smart Guardian" di ITE
Modulo di memoria DDR3 a canale doppio
Supporto di DDR3
800/1066/1333/1600(OC)/1800(OC per CPU
AM3 solo)
DIMM registrati e DIMM ECC non sono supportati
SATA
LAN
Supporto
audio HD
Alloggi
Connettori
su scheda
32
Controller Serial ATA integrato
Realtek RTL 8111F (A960G+)
Realtek RTL 8105E (A960GL+)
ALC662
Alloggio PCI Express X16 x1
Alloggio PCI x1
Connettore SATA x4 Ciascun connettore supporta 1 unità SATA
Connettore pannello frontale x1 Supporta i servizi del pannello frontale
Connettore audio frontale x1 Supporta la funzione audio pannello frontale
Velocità di trasferimento dei dati fino a 3 Gb/s.
Compatibile specifiche SATA Versione 2.0.
Negoziazione automatica 10 / 100 / 1000 Mb/s
Negoziazione automatica 10 / 100 Mb/s
Uscita audio 5.1 canali
Supporto audio High-Definition (HD)
Page 35
SPECIFICA
A960G+/A960GL+
I/O
pannello
posteriore
Collettore ventolina CPU x1
Alimentazione ventolina CPU (con funzione Smart
Fan)
Collettore ventolina sistema x1 Alimentazione ventolina di sistema
Collettore cancellazione CMOS x1
Ciascun connettore supporta 2 porte USB
Connettore USB x2
pannello frontale
Connettore alimentazione x1
(24 pin)
Connettore alimentazione x1
(4 pin)
Connettore Porta stampante x1 Ciascun connettore supporta 1 Porta stampante
Tastiera PS/2 x1
Mouse PS/2 x1
Porta VGA x1
Porta LAN x1
Porta USB x4
Connettore audio x3
Dimension
i scheda
Caratterist
iche
speciali
Sistemi
operativi
supportati
182 mm (larghezza) x 225 mm
(altezza)
Supporto RAID 0 / 1 / 10
Windows XP / Vista / 7
Biostar si riserva il diritto di aggiungere o
rimuovere il supporto di qualsiasi sistema
operativo senza preavviso.
33
Page 36
Motherboard Manual
SPANISH
Especificación
CPU
FSB
Conjunto
de chips
Súper E/S
Memoria
principal
Gráficos
Conector AM3 / AM3+
Procesadores AMD Sempron/Athlon II /
Phenom II /FX (Vatio máximo: 95W)
Admite HyperTransport 3.0 con un ancho
de banda de hasta 4.4 GT/s
AMD 760G
AMD SB710
ITE 8728
Le ofrece las funcionalidades heredadas
de uso más común Súper E/S.
Ranuras DIMM DDR3 x 2
Capacidad máxima de memoria de 16GB
Cada DIMM admite DDR de
512MB/1GB/2GB/4GB/8GB
Integrados en el conjunto de chips AMD
760G
La arquitectura AMD 64 permite el procesado de 32 y
64 bits
Soporta las tecnologías Hyper Transport 3.0
Interfaz de cuenta Low Pin
Iniciativas de control de entorno,
Monitor hardware
Función "Guardia inteligente" de ITE
Módulo de memoria DDR3 de canal Doble
Admite DDR3 de 800/1066/1333/1600(OC)/1866(OC
para CPU AM3 solamente)
No admite DIMM registrados o DIMM compatibles con
ECC
Memoria máxima de vídeo compartida de 512 MB
SATA
Red Local
Soporte de
sonido HD
Ranuras
Conectores
en placa
34
Controlador ATA Serie Integrado
Realtek RTL 8111F (A960G+)
Realtek RTL 8105E (A960GL+)
ALC662
Ranura PCI Express X16 X1
Ranura PCI X1
Conector SATA X4 Cada conector soporta 1 dispositivos SATA
Conector de panel frontal X1 Soporta instalaciones en el panel frontal
Tasas de transferencia de hasta 3 Gb/s.
Compatible con la versión SATA 2.0.
Negociación de 10 / 100 / 1000 Mb/s
Negociación de 10 / 100 Mb/s
Salida de sonido de 5.1 canales
Soporte de sonido Alta Definición
Page 37
A960G+/A960GL+
Especificación
Conector de sonido frontal X1 Soporta funciones de sonido en el panel frontal
Cabecera de ventilador de CPU X1 Fuente de alimentación de ventilador de CPU (con
función Smart Fan)
Cabecera de ventilador de sistema X1 Fuente de alimentación de ventilador de sistema
Cabecera de borrado de CMOS X1
Conector USB X2 Cada conector soporta 2 puertos USB frontales
Panel
trasero de
E/S
Tamaño d e
la placa
Funciones
especiales
Soporte de
sistema
operativo
Conector de alimentación X1
(24 patillas)
Conector de alimentación X1
(4 patillas)
Conector Puerto de impresora X1 Cada conector soporta 1 Puerto de impresora
Teclado PS/ 2 X1
Ratón PS/2 X1
Puerto VGA X1
Puerto de red local X1
Puerto USB X4
Conector de sonido X3
182 mm. (A) X 225 Mm. (H)
Admite RAID 0 / 1 / 10
Biostar se reserva el derecho de añadir o retirar el
Windows XP / Vista / 7
soporte de cualquier SO con o sin aviso previo.
35
Page 38
Motherboard Manual
PORTUGUESE
Socket AM3 / AM3+
CPU
Processadores AMD Sempron/Athlon II /
Phenom II /FX (Watt máximo: 95W)
ESPECIFICAÇÕES
A arquitectura AMD 64 permite uma computação de 32
e 64 bits
Suporta as tecnologias Hyper Transport 3.0
FSB
Chipset
Especificaç
ão Super
I/O
Memória
principal
Placa
gráfica
SATA
Suporta a tecnologia HyperTransport 2.0
com uma largura de banda até 4.4 GT/s
AMD 760G
AMD SB710
ITE 8728
Proporciona as funcionalidades mais
utilizadas em termos da especificação
Super I/O.
Ranhuras DIMM DDR3 x 2
Capacidade máxima de memória: 16GB
Cada módulo DIMM suporta uma
memória DDR3 de 512MB/1GB/
2GB/4GB/8GB
Integrada no chipset AMD 760G Memória de vídeo máxima partilhada: 512 MB
Controlador Serial ATA integrado
Interface LPC (Low Pin Count).
Iniciativas para controlo do ambiente
Monitorização do hardware
Função "Smart Guardian" da ITE
Módulo de memória DDR3 de canal duplo
Suporta módulos DDR3
800/1066/1333/1600(OC)/1866(OC para o CPU AM3
só)
Os módulos DIMM registados e os DIMM ECC não são
suportados
Velocidades de transmissão de dados até 3 Gb/s.
Compatibilidade com a especificação SATA versão 2.0.
LAN
Suporte
para áudio
de alta
definição
Ranhuras
Conectores
36
Realtek RTL 8111F (A960G+)
Realtek RTL 8105E (A960GL+)
ALC662
Ranhura PCI Express X16 x1
Ranhura PCI x1
Conector SATA x4 Cada conector suporta 1 dispositivo SATA
Auto negociação de 10 / 100 / 1000 Mb/s
Auto negociação de 10 / 100 Mb/s
Saída de áudio de 5.1 canais
Suporta a especificação High-Definition Audio
Page 39
na placa
A960G+/A960GL+
ESPECIFICAÇÕES
Conector do painel frontal x1 Para suporte de várias funções no painel frontal
Conector de áudio frontal x1 Suporta a função de áudio no painel frontal
Entradas/S
aídas no
painel
traseiro
Ta ma n ho
da placa
Característi
cas
especiais
Sistemas
operativos
suportados
Conector da ventoinha da CPU x1
Conector da ventoinha do sistema x1 Alimentação da ventoinha do sistema
Conector para limpeza do CMOS x1
Conector USB x2 Cada conector suporta 2 portas USB no painel frontal
Conector de alimentação x1
(24 pinos)
Conector de alimentação x1
(4 pinos)
Conector da para impressora x1 Cada conector suporta 1 Porta para impressora
Teclado PS/ 2 x1
Rato PS/2 x1
Porta VGA x1
Porta LAN x1
Porta USB x4
Tomada de áudio x3
182 mm (L) X 225 mm (A)
Suporta as funções RAID 0 / 1 / 10
Windows XP / Vista / 7
Alimentação da ventoinha da CPU (com a função Smart
Fan)
A Biostar reserva-se o direito de adicionar ou remover
suporte para qualquer sistema operativo com ou sem
aviso prévio.
37
Page 40
Motherboard Manual
POLISH
SPEC
Procesor
FSB
Chipset
Pamięć
główna
Super I/O
Grafika
Socket AM3 / AM3+
AMD Sempron/Athlon II / Phenom II /FX
Procesory (Maksymalny Watt: 95W)
Obsługa HyperTransport 3.0 o szerokości
pasma do 4.4 GT/s
AMD 760G
AMD SB710
Gniazda DDR3 DIMM x 2
Maks. wielkość pamięci 16GB
Każde gniazdo DIMM obsługuje moduły
512MB/1GB/2GB/4GB/8GB DDR3
ITE 8728
Zapewnia najbardziej powszechne
funkcje Super I/O.
Zintegrowana w chipsecie AMD 760G
Architektura AMD 64 umożliwia przetwarzanie 32 i 64
bitowe
Obsługa Hyper Transport 3.0
Moduł pamięci DDR3 z trybem podwójnego kanału
Obsługa DDR3 800/1066/1333/1600(OC)/1866(OC
dla procesorów AM3 tylko)
Brak obsługi Registered DIMM oraz ECC DIMM
Interfejs Low Pin Count
Funkcje kontroli warunków pracy,
Monitor H/W
Funkcja ITE "Smart Guardian"
Maks. wielkość współdzielonej pamięci video wynosi
512 MB
SATA
LAN
Obsługa
audio HD
Gniazda
Złącza
wbudowan
e
38
Zintegrowany kontroler Serial ATA
Transfer danych do 3 Gb/s.
Zgodność ze specyfikacją SATA w wersji 2.0.
Realtek RTL 8111F (A960G+), 10/ 100/ 1000 Mb/s z automatyczną negocjacją szybkości
Realtek RTL 8105E (A960GL+), 10/ 100 Mb/s z automatyczną negocjacją szybkości
5.1 kanałowe wyjście audio
ALC662
Obsługa High-Definition Audio
Gniazdo PCI Express X16 x1
Gniazdo PCI x1
Złącze SATA x4 Każde złącze obsługuje 1 urządzenie SATA
Złącze panela przedniego x1 Obsługa elementów panela przedniego
Przednie złącze audio x1 Obsługa funkcji audio na panelu przednim
Page 41
SPEC
A960G+/A960GL+
Back Panel
I/O
Wymiary
płyty
Funkcje
specjalne
Obsluga
systemu
operacyjne
go
Złącze główkowe wentylatora procesora
x1
Złącze główkowe wentylatora
systemowego x1
Złącze główkowe kasowania CMOS x1
Złącze USB x2
Złącze zasilania (24 pinowe) x1
Złącze zasilania (4 pinowe) x1
Złącze Port drukarki x1 Każde złącze obsługuje 1 Port drukarki
Klawiatura PS/2 x1
Mysz PS/2 x1
Port VGA x1
Port LAN x1
Port USB x4
Gniazdo audio x3
182 mm (S) X 225 mm (W)
Obsługa RAID 0 / 1 / 10
Windows XP / Vista / 7
Zasilanie wentylatora procesora (z funkcją Smart Fan)
Zasilanie wentylatora systemowego
Każde złącze obsługuje 2 porty USB na panelu
przednim
Biostar zastrzega sobie prawo dodawania lub
odwoływania obsługi dowolnego systemu
operacyjnego bez powiadomienia.
39
Page 42
Motherboard Manual
RUSSIAN
CPU (централь
ный
процессор
)
FSB
Набор микросхем
Основная память
Super I/O
Графика
SATA
Локальная сеть
Звуковая
поддержка жесткого диска
Слоты
Встроенны й разъём
40
Гнездо AM3 / AM3+
Процессоры AMD Sempron/Athlon II /
Phenom II /FX (Максимальный ватт:
95W)
Поддержка HyperTransport 3.0 с
пропускной способностью до 4.4 GT/s
AMD 760G
AMD SB710
Слоты DDR3 DIMM x 2
Максимальная ёмкость памяти 16ГБ
Каждый модуль DIMM поддерживает
512МБ/1ГБ/2ГБ/4ГБ/8ГБ DDR3
ITE 8728
Обеспечивает наиболее используемые
действующие функциональные
возможности Super I/O.
Встроенная в набор микросхем AMD
760G
Встроенное последовательное
устройство управления ATA
Realtek RTL 8111F (A960G+)
Realtek RTL 8105E (A960GL+)
ALC662
Слот PCI Express X16 x1
Слот PCI x1
Разъём SATA x4 Каждый разъём поддерживает 1 устройство SATA
Разъём на лицевой панели x1 Поддержка устройств на лицевой панели
СПЕЦ
Архитектура AMD 64 разрешать обработка данных
на 32 и 64 бит
Поддержка Hyper Transport 3.0
Модуль памяти с двухканальным режимом DDR3
Поддержка DDR3
800/1066/1333/1600(OC)/1866(OC для
процессоров AM3 только)
Не поддерживает зарегистрированные модули
DIMM and ECC DIMM
Интерфейс с низким количеством выводов
Инициативы по охране окружающей среды,
Аппаратный монитор
Функция ITE "Smart Guardian" (Интеллектуальная
защита)
Максимальная совместно используемая видео
память составляет 512 МБ
скорость передачи данных до 3 гигабит/с.
Соответствие спецификации SATA версия 2.0.
Автоматическое согласование 10 / 100 / 10000 Мб
Автоматическое согласование 10 / 100 Мб/с
Звуковая поддержка High-Definition
5.1канальный звуковой выход
Page 43
Задняя панель средств ввода-выв ода
Размер панели
Специальн ые
техническ ие
характери стики
Поддержк а OS
A960G+/A960GL+
СПЕЦ
Входной звуковой разъём x1 Поддержка звуковых функций на лицевой панели
Контактирующее приспособление
вентилятора центрального
процессора x1
Контактирующее приспособление
вентилятора системы x1
Открытое контактирующее
приспособление CMOS x1
USB-разъём x2
Разъем питания (24 вывод) x1
Разъем питания (4 вывод) x1
Разъём Порт подключения
принтера x1
Клавиатура PS/2 x1
Мышь PS/2 x1
Порт VGA x1
Порт LAN x1
USB-порт x4
Гнездо для подключения
наушников x3
182 мм (Ш) X 225 мм (В)
Поддержка RAID 0 / 1 / 10
Windows XP / Vista / 7
Источник питания для вентилятора центрального
процессора (с функцией интеллектуального
вентилятора)
Источник питания для вентилятора системы
Каждый разъём поддерживает 2 USB-порта на
лицевой панели
Каждый разъём поддерживает 1 Порт подключения
принтера
Biostar сохраняет за собой право добавлять или
удалять средства обеспечения для OS с или без
предварительного уведомления.
41
Page 44
Motherboard Manual
ARABIC
تﺎﻔﺻاﻮﻤﻟا
ﺔﻴﻨﻘﺗ ﻦﻜﻤﺗAMD 64 ﺔﻋﺮﺴﺑ ﺔﻴﺑﻮﺳﺎﺤﻟا تﺎﻴﻠﻤﻌﻟا ءاﺮﺟإ 32 و64 ﺖﺑ
ﺔﻴﻨﻘﺗ ﻢﻋﺪﺗHyper Transport و 3.0
ﺔﻴﻨﻘﺗ ﻢﻋﺪﺗLow Pin Count Interface
ةﺰﻬﺟﻷا ﺔﻟﺎﺣ ﺔﻓﺮﻌﻤﻟ ﺐﻗاﺮﻣ
ﺔﻔﻴﻇو"Smart Guardian" ﻦﻣ ITE
ةﺮآاذ ةﺪﺣوDDR3 ﻘﻟا ﺔﺟودﺰﻣةﺎﻨ
عﻮﻧ ﻦﻣ ةﺮآاﺬﻟا ﻢﻋﺪﺗDDR3 تﺎﻌﺳ
ﺖﻳﺎﺑ/1866 (OC ل تﺎﺠﻟﺎﻌﻣ AM3 ﻂﻘﻓ)
ةﺮآاﺬﻟا ﻖﺋﺎﻗر ﻢﻋﺪﺗ DIMM ﻊﻣ ﻖﻓاﻮﺘﺗ ﻻ ﻲﺘﻟا ﻚﻠﺗو ECC
ﺔﺌﻴﺒﻟا ﻲﻓ ﻢﻜﺤﺘﻟا ﻞﺋﺎﺳو:
ﻰﺼﻗأ ﺔﻌﺳ ةﺮآاﺬﻟ ﻮﻳﺪﻴﻔﻟا ﺔآﺮﺘﺸﻤﻟا 512 ﺎﺠﻴﻣ ﺖﻳﺎﺑ
ﺲﺒﻘﻣAM3 / AM3+
تﺎﺠﻟﺎﻌﻣAMD Sempron/Athlon II / Phenom II /FX
(طاو ىﻮﺼﻗ: 95و)
ﺔﻴﻨﻘﺗ ﻢﻋﺪﺗHyperTransport ﻰﻟإ ﻞﺼﻳ ددﺮﺘﺑ 3.0 4.4 GT/s
ﺔﻔﻴﻇو ﺮﻓﻮﺗSuper I/O ًﺎ ﻣ ا ﺪ ﺨﺘﺳ ا ﺮﺜآﻷا .
800/1066/1333/1600)OC( ﺎﺠﻴﻣ
ﺔﺤﺘﻓ ﻞآ ﻢﻋﺪﺗDIMM عﻮﻧ ﻦﻣ ةﺮآاذ ﻢﻋﺪ DDR3 ﺔﻌﺳ
ﻖﺋﺎﻗر ﻲﻓ ﺔﺠﻣﺪﻣ AMD 760G
ةﺪﺣو ﺔﺠﻟﺎﻌﻤﻟا
ﺔﻳﺰآﺮﻤﻟا
ﻞﻗﺎﻨﻟا ﻲﻣﺎﻣﻷا ﻲﺒﻧﺎﺠﻟا
AMD 760G
ﺔﻋﻮﻤﺠﻣ ﺢﺋاﺮﺸﻟا
AMD SB710
ITE 8728
Super I/O
ﺔﺤﺘﻓDDR3 DIMM دﺪﻋ2
ىﻮﺼﻗ ةﺮآاذ ﺔﻌﺳ16 ﺖﻳﺎﺑ ﺎﺠﻴﺟ
ةﺮآاﺬﻟا ﺔﻴﺴﻴﺋﺮﻟا
/512 ﺖﻳﺎﺑ ﺎﺠﻴﻣ
و1/و 2/و 4/و 8 ﺎﺠﻴﺟﺖﻳﺎﺑ
ﺔﻗﺎﻄﺑ تﺎﻣﻮﺳﺮﻟا
ﺔﻘﺑﺎﻄﻣ تﺎﻔﺻاﻮﻤﻟ SATA راﺪﺻﻹا 2.0.
ﺎﺠﻴﻣ / ﺔﻴﻧﺎﺛ ضوﺎﻔﺗ تارﺎﻴﺴﻟا 10/100/1000
ﺎﺠﻴﻣ / ﺔﻴﻧﺎﺛ ضوﺎﻔﺗ تارﺎﻴﺴﻟا 10/100
ﻦﻣ ﻒﻳﺮﻌﺘﻟا ﻲﻟﺎﻋ تﻮﺼﻟا ﺔﻴﻨﻘﺗ ﻢﻋﺪﺗ
ةﺰﻬﺟأ ﻦﻣ ﺪﺣاو ﺬﻔﻨﻣ ﻞآ ﻢﻋﺪﻳSATA
ﺔﻴﻣﺎﻣﻷا ﺔﺣﻮﻠﻟﺎﺑ تﻮﺼﻟا ﺔﻔﻴﻇو ﻢﻋﺪﻳ
42
ﻞﻘﻧ تﺎﻧﺎﻴﺒﻟا تﺎﻋﺮﺴﺑ ﻞﺼﺗ ﻰﻟإ 3 ﺖﺑﺎﺠﻴﺟ/ﺔﻴﻧﺎﺛ.
5.1 تاﻮﻨﻗ جﺮﺨﻟ تﻮﺼﻟا
ﺔﻴﻣﺎﻣﻷا ﺔﺣﻮﻠﻟا تاﺰﻴﻬﺠﺗ ﻢﻋﺪﻳ
ﺔﺤﺘﻓx16 PCI Express دﺪﻋ1
ﺔﺤﺘﻓPCI دﺪﻋ1
ﻜﺤﺘﻣ Serial ATA ﻞﻣﺎﻜﺘﻣ
Realtek RTL 8111F (A960G+)
Realtek RTL 8105E (A960GL+)
ALC662
ﺬﻔﻨﻣSATA دﺪﻋ4
ﺔﻴﻣﺎﻣﻷا ﺔﺣﻮﻠﻟا ﺬﻔﻨﻣ دﺪﻋ1
ﻲﻣﺎﻣﻷا تﻮﺼﻟا ﺬﻔﻨﻣ دﺪﻋ1
SATA
ﺔﻜﺒﺷ ﺔﻴﻠﺧاد
ﻢﻋد تﻮﺼﻟا ﻲﻟﺎﻋ
ﻒﻳﺮﻌﺘﻟا
تﺎﺤﺘﻔﻟا
ﺬﻓﺎﻨﻤﻟا ﻰﻠﻋ ﺢﻄﺳ
ﺔﺣﻮﻠﻟا
Page 45
تﺎﻔﺻاﻮﻤﻟا
A960G+/A960GL+
ﻗﺎﻄﻟا ﻞﻴﺻﻮﺘﻟ ﺔﻔﻴﻇو ﻊﻣ ﺔﺠﻟﺎﻌﻤﻟا ةﺪﺣو ﺔﺣوﺮﻤﻟ ﺔ Smart Fan
مﺎﻈﻨﻟا ﺔﺣوﺮﻤﻟ ﺔﻗﺎﻄﻟا ﻞﻴﺻﻮﺘﻟ
ﺢﺴﻣ ﺔﻠﺻوCMOS دﺪﻋ1
ﻲﺘﺤﺘﻓ ﺬﻔﻨﻣ ﻞآ ﻢﻋﺪﻳUSBﺔﻴﻣﺎﻣﻷا ﺔﺣﻮﻠﻟﺎﺑ
ﺔﻗﺎﻄﻟا ﻞﻴﺻﻮﺗ ﺬﻔﻨﻣ)24سﻮﺑد( دﺪﻋ1
ﺔﻗﺎﻄﻟا ﻞﻴﺻﻮﺗ ﺬﻔﻨﻣ)4سﻮﺑد( دﺪﻋ1
ﺔﻌﺑﺎﻃ ﺬﻔﻨﻣ دﺪﻋ1
182 ﻢﻣ)ضﺮﻋ (X 225 ﻢﻣ)عﺎﻔﺗرا(
ﻆﻔﺘﺤﺗBiostar وأ رﺎﻄﺧﺈﺑ ﻞﻴﻐﺸﺗ مﺎﻈﻧ يﻷ ﻢﻋﺪﻟا ﺔﻟازإ وأ ﺔﻓﺎﺿإ ﻲﻓ ﺎﻬﻘﺤﺑ
رﺎﻄﺧإ نوﺪﺑ.
ﺔﻳﺰآﺮﻤﻟا ﺔﺠﻟﺎﻌﻤﻟا ةﺪﺣو ﺔﺣوﺮﻣ ﺔﻠﺻو دﺪﻋ1
مﺎﻈﻨﻟا ﺔﺣوﺮﻣ ﺔﻠﺻو دﺪﻋ1
ﺔﻴﻠﺤﻣ لﺎﺼﺗا ﺔﻜﺒﺷ ﺬﻔﻨﻣ دﺪﻋ1
ﺔﻴﻨﻘﺗ ﻢﻋﺪﺗRAID 0 / 1 / 10
Windows XP / Vista / 7
ﺬﻔﻨﻣUSB دﺪﻋ2
ﺢﻴﺗﺎﻔﻣ ﺔﺣﻮﻟPS/2 دﺪﻋ1
سوﺎﻣ PS/2 دﺪﻋ1
ﺬﻔﻨﻣVGA دﺪﻋ1
ﺬﻓﺎﻨﻣ ﻞﺧد/جﺮﺧ
ﺔﺣﻮﻠﻟا ﺔﻴﻔﻠﺨﻟا
ﺬﻓﺎﻨﻣUSB دﺪﻋ4
تﻮﺻ ﺲﺒﻘﻣ ﺪﻋ3
ﻢﺠﺣ ﺔﺣﻮﻠﻟا
ﺔﺻﺎﺧ ﺎﻳاﺰﻣ
ﻢﻋد ﺔﻤﻈﻧأ ﻞﻴﻐﺸﺘﻟا
43
Page 46
Motherboard Manual
JAPANESE
仕様
CPU
FSB
チップセッ
メインメモ
Super I/O
グラフィッ
クス
Socket AM3 / AM3+
AMD Sempron/Athlon II / Phenom II /FX
プロセッサ (最高のワット: 95W)
4.4 GT/sのバンド幅までハイパートランスポ
ート3.0をサポートします
AMD 760G
AMD SB710
DDR3 DIMMスロット x 2
最大メモリ容量16GB
DIMMは 512MB/1GB/2GB/4GB/8GB
DDR3をサポート
ITE 8728
もっとも一般に使用されるレガシーSuper I/O
機能を採用しています。
AMD 760Gチップセットに統合 最大の共有ビデオメモリは512MBです
AMD 64アーキテクチャでは、32ビットと64ビット計算が可
能です
ハイパートランスポート3.0とクールアンドクワイアットを
サポートします
デュアル チャンネルモードDDR3メモリモジュール
DDR3 800/1066/1333/1600(OC)/1866(唯一のAM3
CPUのOC) をサポート
登録済みDIMMECC DIMMはサポートされません
低ピンカウントインターフェイス
環境コントロールイニシアチブ、
H/Wモニター
ITEの「スマートガーディアン」機能
SATA
LAN
HDオーディ
オのサポー
スロット
オンボード
コネクタ
44
統合シリアルATAコントローラ
Realtek RTL 8111F (A960G+)
Realtek RTL 8105E (A960GL+)
ALC662
PCI Express X16スロット x1
PCIスロット x1
SATAコネクタ x4 各コネクタは1つのSATAデバイスをサポートします
フロントパネルコネクタ x1 フロントパネル機能をサポートします
最高3Gb/秒のデータ転送速度
SATAバージョン2.0仕様に準拠。
10 / 100 / 1000 Mb/秒のオートネゴシエーション
10 / 100 Mb/秒のオートネゴシエーション
5.1チャンネルオーディオアウト
ハイデフィニションオーディオのサポート
Page 47
A960G+/A960GL+
仕様
フロントオーディオコネクタ x1 フロントパネルオーディオ機能をサポートします
CPUファンヘッダ x1 CPUファン電源装置(スマートファン機能を搭載)
システムファンヘッダ x1 システムファン電源装置
CMOSクリアヘッダ x1
背面パネル
I/O
ボードサイ
特殊機能
OSサポート
USBコネクタ x2
各コネクタは2つのフロントパネルUSBポートをサポートし
ます
電源コネクタ(24ピン) x1
電源コネクタ(4ピン) x1
プリンタポートコネクタ x1 各コネクタは1つのプリンタポートをサポートします
PS/2キーボード x1
PS/2マウス x1
VGAポート x1
LANポート x1
USBポート x4
オーディオジャック x3
182 mm (幅) X 225 mm (高さ)
RAID 0 / 1 / 10 のサポート
Biostarは事前のサポートなしにOSサポートを追加または削
Windows XP / Vista / 7
除する権利を留保します。
2013/01/15
45
Loading...