Biostar A58ML, A58MD Owner's Manual

A58MD / A58MG / A58ML Setup Manual

FCC Information and Copyright

This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. There is no guarantee that interference will not occur in a particular installation.

The vendor makes no representations or warranties with respect to the contents here and specially disclaims any implied warranties of merchantability or fitness for any purpose. Further the vendor reserves the right to revise this publication and to make changes to the contents here without obligation to notify any party beforehand.

Duplication of this publication, in part or in whole, is not allowed without first obtaining the vendor’s approval in writing.

The content of this user’s manual is subject to be changed without notice and we will not be responsible for any mistakes found in this user’s manual. All the brand and product names are trademarks of their respective companies.

Dichiarazione di conformità sintetica

Ai sensi dell’art. 2 comma 3 del D.M. 275 del 30/10/2002

Si dichiara che questo prodotto è conforme alle normative vigenti e soddisfa i requisiti essenziali richiesti dalle direttive

2004/108/CE, 2006/95/CE e 1999/05/CE

quando ad esso applicabili

Short Declaration of conformity

We declare this product is complying with the laws in force and meeting all the essential requirements as specified by the directives

2004/108/CE, 2006/95/CE and 1999/05/CE

whenever these laws may be applied

Table of Contents

Chapter 1: Introduction ...............................................................1

1.1 Before You Start......................................................................... 1

1.2 Package Checklist..................................................................... 1

1.3 Motherboard Specifications....................................................... 2

1.4 Rear Panel Connectors ............................................................. 3

1.5 Motherboard Layout .................................................................. 4

Chapter 2: Hardware Installation................................................5

2.1 Install Central Processing Unit (CPU) ....................................... 5

2.2 Install a Heatsink ....................................................................... 5

2.3 Connect Cooling Fans............................................................... 7

2.4 Install System Memory .............................................................. 8

2.5 Expansion Slots....................................................................... 10

2.6 Jumper Setting .........................................................................11

2.7 Headers & Connectors ............................................................ 12

Chapter 3: UEFI BIOS & Software.............................................16

3.1 UEFI BIOS Setup .................................................................... 16

3.2 BIOS Update ........................................................................... 16

3.3 Software................................................................................... 21

Chapter 4: Useful Help .............................................................. 24

4.1 Driver Installation..................................................................... 24

4.2 AMI BIOS Beep Code.............................................................. 25

4.3 Troubleshooting....................................................................... 25

4.4 RAID Functions ....................................................................... 26

4.5 AMD DUAL Graphics Technology ........................................... 28

Appendix: Specifications In Other Languages .......................30

Arabic ......................................................................................................... 30

French ........................................................................................................ 32

German....................................................................................................... 34

Italian.......................................................................................................... 36

Japanese.................................................................................................... 38

Polish.......................................................................................................... 40

Portuguese ................................................................................................. 42

Russian....................................................................................................... 44

Spanish....................................................................................................... 46

A58MD/A58MG/A58ML

CHAPTER 1: INTRODUCTION

1.1 Before You Start

Thank you for choosing our product. Before you start installing the motherboard, please make sure you follow the instructions below:

 Prepare a dry and stable working environment with

sufficient lighting.

 Always disconnect the computer from power outlet before

operation.

 Before you take the motherboard out from anti-static bag,

ground yourself properly by touching any safely grounded appliance, or use grounded wrist strap to remove the static charge.

 Avoid touching the components on motherboard or the rear

side of the board unless necessary. Hold the board on the edge, do not try to bend or flex the board.

 Do not leave any unfastened small parts inside the case

after installation. Loose parts will cause short circuits which may damage the equipment.

 Keep the computer from dangerous area, such as heat

source, humid air and water.

 The operating temperatures of the computer should be 0 to

45 degrees Celsius.

 To avoid injury, be careful of:

Sharp pins on headers and connectors Rough edges and sharp corners on the chassis Damage to wires that could cause a short circuit

1.2 Package Checklist

; Serial ATA Cable x2 ; Rear I/O Panel for ATX Case x1 ; Installation Guide x1 ; Fully Setup Driver DVD x1

Note: The package contents may be different due to the sales region or models in which it was sold. For more information about the standard package in your region, please contact your dealer or sales representative.

Motherboard Manual

1.3 Motherboard Specifications

Specifications

Socket FM2+/FM2 for AMD A-series processor

CPU Support

Chipset AMD A55 FCH

Memory

Storage

LAN

Audio Codec

USB

Expansion Slots

Rear I/Os

Internal I/Os

Form Factor microATX Form Factor, 218 mm x 174 mm

OS Support

Maximum CPU TDP (Thermal Design Power): 100Watt * Please refer to www.biostar.com.tw

Supports Dual Channel DDR3 800/ 1066/ 1333/ 1600/ 1866/ 2133/ 2400(OC)/ 2600(OC) 2 x DDR3 DIMM Memory Slot, Max. Supports up to 32 GB Memory Each DIMM supports non-ECC 512MB/ 1/ 2/ 4/ 8/ 16 GB DDR3 module * Please refer to www.biostar.com.tw AMD A55 FCH 4x SATA 3Gb/s Connector Supports RAID 0,1,10 & AHCI Realtek RTL 8111G (A58MD, A58MG) 10/ 100/ 1000 Mb/s auto negotiation, Half / Full duplex capability Realtek RTL 8106E (A58ML) 10/ 100 Mb/s auto negotiation, Half / Full duplex capability ALC662

5.1 Channels, High Definition Audio AMD A55 FCH 8x USB 2.0 port (4 on rear I/Os and 4 via internal headers) 1x PCIe x1 Slot 1x PCIe 3.0 x16 Slot (Only FM2+ processors can support PCIe 3.0.) 1x PS/2 Mouse 1x PS/2 Keyboard 1x VGA Port 1x DVI Port (A58MD) 1x LAN port 4x USB 2.0 Port 3x Audio Jack 4x SATA 3.0Gb/s Connector 2x USB 2.0 Header (each header supports 2 USB 2.0 ports) 1x 4-Pin Power Connector 1x 24-Pin Power Connector 1x CPU Fan Connector 1x System Fan Connector 1x Front Panel Header 1x Front Audio Header 1x Clear CMOS Header 1x Serial Port Header 1x Chassis Speaker Header

Windows XP / 7 / 8 Biostar reserves the right to add or remove support for any OS with or without notice.

for CPU support list.

for Memory support list.

A58MD/A58MG/A58ML

1.4 Rear Panel Connectors

A58MD

A58MG/ A58ML

Note 1: DVI-D / VGA Output require an AMD family processor with intedrated graphics. Note 2: The mainboard supports two independent display outputs. (A58MD) Note 3: Since the audio chip supports High Definition Audio Specification, the function of each

Note 4: Maximum resolution:

audio jack can be defined by software. The input / output function of each audio jack listed above represents the default setting. However, when connecting external microphone to the audio port, please use the Line In (Blue) and Mic In (Pink) audio jack.

Outputs Maximum resolution Bit Depth

DVI-D

VGA 1920 x 1600 @60Hz --

1920 x 1200 @60Hz 30 bpp 2560 x 1600 @60Hz 24 bpp

Motherboard Manual

1.5 Motherboard Layout

Note: ■ represents the 1st pin.

A58MD/A58MG/A58ML

CHAPTER 2: HARDWARE INSTALLATION

2.1 Install Central Processing Unit (CPU)

Step 1: Locate the CPU socket on the motherboard

Step 2: Pull the socket locking out from the socket and then raise the lever up

to a 90-degree angel.

Step 3: Look for the white triangle on socket, and the gold triangle on CPU

should point towards this white triangle. The CPU will fit only in the correct orientation.

Motherboard Manual

Step 4: Hold the CPU down firmly, and then close the lever to locked the

position

2.2 Install a Heatsink

Step 1: Place the heatsink and fan assembly onto the retention frame. Match the

heatsink clip with the socket mounting-lug. Hook the spring clip to the mounting-lug.

Step 2: On the other side, push the retention clip straight down to lock into the

plastic lug on the retention frame, and then press down the locker until it stops.

Note1: Do not forget to connect the CPU fan connector. Note2: For proper installation, please kindly refer to the installation manual of your CPU heatsink.

A58MD/A58MG/A58ML

2.3 Connect Cooling Fans

These fan headers support cooling-fans built in the computer. The fan cable and connector may be different according to the fan manufacturer. Connect the fan cable to the connector while matching the black wire to pin#1.

CPU_FAN1: CPU Fan Header

Pin Assignment

1 Ground 2 +12V 3 FAN RPM rate sense 4 Smart Fan Control(By Fan)

SYS_FAN1: System Fan Header

Pin Assignment

1 Ground 2 +12V 3

FAN RPM rate sense

Note: CPU_FAN1, SYS_FAN1 support 4-pin and 3-pin head connectors. When connecting with wires onto connectors, please note that the red wire is the positive and should be connected to pin#2, and the black wire is Ground and should be connected to GND.

Motherboard Manual

2.4 Install System Memory

A. DDR3 Modules

Step 1: Unlock a DIMM slot by pressing the retaining clips outward. Align a DIMM

on the slot such that the notch on the DIMM matches the break on the slot.

Step 2: Insert the DIMM vertically and firmly into the slot until the retaining clips

snap back in place and the DIMM is properly seated.

Note: If the DIMM does not go in smoothly, do not force it. Pull it all the way out and try again.

A58MD/A58MG/A58ML

B. Memory Capacity

DIMM Socket Location

DDR3_A1 512MB/1GB/2GB/4GB/8GB/16GB DDR3_B1 512MB/1GB/2GB/4GB/8GB/16GB

DDR3 Module

Total Memory Size

Max is 32GB.

C. Dual Channel Memory Installation

Please refer to the following requirements to activate Dual Channel function: Install memory module of the same density in pairs, shown in the table.

Dual Channel Status DDR3_A1 DDR3_B1

Disabled O X Disabled X O

Enabled O O

(O means memory installed, X means memory not installed.)

Note: The DRAM bus width of the memory module must be the same (x8 or x16)

Motherboard Manual

2.5 Expansion Slots

PEX16_1: PCI-Express Gen3 x16 Slot

- PCI-Express 3.0 compliant.

- Maximum theoretical realized bandwidth of 16GB/s simultaneously per

direction, for an aggregate of 32GB/s totally.

- Only FM2+ processors can support PCIe 3.0.

PEX1_1: PCI-Express Gen2 x1 Slot

- PCI-Express 2.0 compliant.

- Data transfer bandwidth up to 500MB/s per direction; 1GB/s in total

Install an Expansion Card

You can install your expansion card by following steps:

1. Read the related expansion card's instruction document before install the expansion card into the computer.

2. Remove your computer's chassis cover, screws and slot bracket from the computer.

3. Place a card in the expansion slot and press down on the card until it is completely seated in the slot.

4. Secure the card’s metal bracket to the chassis back panel with a screw.

5. Replace your computer's chassis cover.

6. Power on the computer, if necessary, change BIOS settings for the expansion card.

7. Install related driver for the expansion card.

A58MD/A58MG/A58ML

2.6 Jumper Setting

The illustration shows how to set up jumpers. When the jumper cap is placed on pins, the jumper is “close”, if not, that means the jumper is “open”.

Pin opened Pin closed Pin1-2 closed

JCMOS1: Clear CMOS Header

Placing the jumper on pin2-3, it allows user to restore the BIOS safe setting and the CMOS data. Please carefully follow the procedures to avoid damaging the motherboard.

Pin 1-2 Close:

Normal Operation (default).

※ Clear CMOS Procedures:

1. Remove AC power line.

2. Set the jumper to “Pin 2-3 close”.

3. Wait for five seconds.

4. Set the jumper to “Pin 1-2 close”.

5. Power on the AC.

Load Optimal Defaults and save settings in CMOS.

Pin 2-3 Close:

Clear CMOS data.

Motherboard Manual

2.7 Headers & Connectors

ATXPWR1: ATX Power Source Connector

For better compatibility, we recommend to use a standard ATX 24-pin power supply for this connector. Make sure to find the correct orientation before plugging the connector.

Pin Assignment Pin Assignment

13 +3.3V 1 +3.3V 14 -12V 2 +3.3V 15 Ground 3 Ground 16 PS_ON 4 +5V 17 Ground 5 Ground 18 Ground 6 +5V 19 Ground 7 Ground 20 NC 8 PW_OK 21 +5V 9 Standby Voltage+5V 22 +5V 10 +12V 23 +5V 11 +12V 24 Ground 12 +3.3V

ATXPWR2: ATX Power Source Connector

This connector will provide +12V to CPU power circuit.

Pin Assignment

1 +12V 2 +12V 3 Ground 4 Ground

Note1: Before you power on the system, please make sure that both ATXPWR1 and ATXPWR2 connectors have been plugged-in. Note2: Insufficient power supplied to the system may result in instability or the peripherals not functioning properly. Use of a PSU with a higher power output is recommended when configuring a system with more power-consuming devices.

A58MD/A58MG/A58ML

JPANEL1: Front Panel Header

This connector includes Power-on, Reset, HDD LED and Power LED connections. It allows user to connect the PC case’s front panel switch functions.

Pin Assignment Function Pin Assignment Function

1 N/A N/A 2 Power LED (+)

3 HDD LED(+) 4 Power LED (+)

5 HDD LED(-)

7 Ground 8 Power Button

9 Reset Control

HDD LED

Reset Button

6 Power LED (-)

10 Ground

Power LED

Power-On Button

JSPKR1: Chassis Speaker Header

Please connect the chassis speaker to this header.

Pin Assignment

1 +5V 2 N/A 3 N/A 4 Speaker

+ 34 hidden pages