materials in a safe
place in case you later
need to transport
the unit.
Keep your sales (till)
receipt, which is your
guarantee.
Important note---back up batteries
The Spirit 410 requires 2 x 1.5V AAA size Alkaline batteries installed
into the battery compartment before use.
Warning: The caller display will not work without batteries installed.
1
1. Where to find it
1
2
3
4
5
6
7
8
9
10
11
1. LCD Screen
2. One-Touch Memory buttons
3. Scroll Up & Down buttons
4. Delete button
5. Set/Store button
6. Memory button
7. LNR(Last Number Redial) button
8. Speakerphone button
9. Mute button
10.R(Recall) button
11.Pause button
Binatone Help Line - 0845 345 9677
Calls are charged at Local Call rate.
2
2. Installation
1. Locating the Base unit
The Base unit should be placed on a level surface, in a position where:
the telephone line cable will reach your telephone line socket or
extension socket.
it is not close to a sink, bath or shower, or anywhere else where it
might get wet.
it is not close to other electrical equipment - fridges, washing
machines, microwave ovens, TVs, fluorescent lights, etc.
2. Plug the coiled handset
cord into the Handset.
Plug the other end into
the jack on the left
side of the Base unit.
Make sure the plugs
click into place.
3. Place the Handset in
the Base unit.
Always use the
telephone line
cord supplied
with your
H L
to Modular
Wall jack
4. Plug the telephone line cord free end
into a modular wall jack.
Press the cable into the groove so that
the Base unit stands level.
Spirit 410 phone.
Other telephone
line cords may
not work.
5. Lift the Handset and check for Dial tone
in the earpiece.
Binatone Help Line - 0845 345 9677
Calls are charged at Local Call rate.
3
Installing (or Replacing) the Battery
IMPORTANT
make sure the base unit is disconnected from the telephone line.
Install 2 pcs of Alkaline AAA batteries into the battery compartment and
- Before removing the battery compartment cover,always
place back the cover before use.
Note: 1) Please do NOT use Rechargeable batteries in this phone.
To place the Spirit 410 on a desk, connect
the stand to the bottom of the phone in the
slots near the rear of the base as shown below.
Insert the rigid clips of the stand into the slots
on the bottom of the phone (near the rear of the base). Press down firmly until the flexible
clips clicks into place.
To remove the stand, (1) pinch the flexible
clips, (2) pull back the stand, and then (3)
slide up and forward (3) as shown below.
To place the Spirit 410 on a wall, connect
the stand to the bottom of the phone in the
slots near the front of the base cover as shown below.
Binatone Help Line - 0845 345 9677
Calls are charged at Local Call rate.
5
Desk/Wall mounting continue...
Insert the rigid clips of the stand into the slots
on the bottom of the phone (near the front of the base). Press down firmly until the flexible
clips clicks into place.
To remove the stand, (1) pinch the flexible
clips, (2) pull back the stand, and then (3)
slide up and forward as shown below.
Mark two points on the wall that are 120 mm
apart to lay the fixing centers as shown below.
BE CAREFUL to check that there are no
electrical wires hidden in the wall.
Fix two screws (supplied with the unit) at the
marked locations, leaving approximately 7mm
between the wall and the the screw head.
Hang the cradle unit on the screws using the
wall mount slots. You may need to remove the
telephone from the wall and tighten the
screws so that the cradle is securely fixed and
does not wobble. Place the Handset on the
cradle with the parking hook on the cradle
arranged to fit in the parking recess under the
earpiece on the Handset.
6
Loading...
+ 12 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.