Beurer PE12 Operating And Safety Instructions Manual

1. IMPORTANT SAFETY NOTES
READ THE SAFETY SECTION AND ALL INSTRUCTIONS AND WARNINGS COMPLETELY AND CAREFULLY BEFORE USING THIS PRODUCT. FOLLOW ALL SAFETY INSTRUCTIONS AND WARNINGS TO AVOID HAZARDOUS SITU­ATIONS AND TO USE THIS PRODUCT CORRECTLY.
WARNING WARNING indicates a hazardous situation which, if not
CAUTION CAUTION indicates a hazardous situation which, if not
avoided, may result in minor or moderate injury.
NOTICE NOTICE addresses practices not related to personal injury,
such as product and/or property damage.
WARNING
Contact your physician or healthcare provider before beginning a weight reduc-
tion or exercise program.
Keep the unit out of the reach of children. This product contains small parts that
may present a choking hazard. Immediately contact your physician if any piece is swallowed. In case of emergency call 911 immediately.
The unit contains a battery therefore always obey general warnings concerning
batteries: – Swallowing batteries and/or battery fluid can be extremely dangerous. Keep
batteries and the unit out of the reach of children. Should a child, or any other person, swallow a battery and/or battery fluid, please call 911 immediately.
– Batteries should not be taken apart, thrown in the fire or short circuited.
Read and understand all instructions in the instruction manual and any other lit-
erature included with the unit before use.
CAUTION
Use the unit only on human beings and for its intended purpose. Do not use for any other purpose.
NOTICE
This unit must only be used with parts and accessories authorized by the manu-
facturer. Parts and accessories not approved for use with the device may dam­age the unit.
Never attempt to repair, open and disassemble the unit or adjust it yourself. This
may damage the unit and impair the functions. If repair is needed please contact our customer service. (See warranty for service contact.)
Changes or modifications to the unit will nullify the user warranty.
The unit is not waterproof. Never immerse the unit in water or any other liquid,
touch it with wet hands, or use it in the rain otherwise liquid will enter the unit and cause damage.
Do not use any aggressive solvents, cleaning agents, detergents or any other
strong chemicals to clean the device.
Protect the unit from strong shocks (e.g. dropping the unit on the floor), direct
sunshine, high temperatures, high humidity, rain, and/or dust.
• Always dispose of the device, battery, and components in accordance with appli-
cable local regulations. Unlawful disposal may cause environmental pollution.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE
If the instruction manual is damaged or if you no longer have the instruction man­ual in your possession, please contact customer service. See “warranty section” for service contact.
Congratulations on your purchase of the beurer Multi- Function Pedom­eter PE12.
It helps you to manage your daily activity and offers you the following functions: step counter function, distance calculation, calorie burned indication.
If you have any questions about your beurer Pedometer, call customer service at toll free 1-800-536-0366.
2. Package Content
Pedometer PE12
Battery 1.5 V (already installed)
Instructions for use
3. Getting to know your Unit
4. Attachment
The paces are detected by the movement of the waist. Attach the pedo meter to your belt or the top of your shorts, pants or skirt with its clip. It should fit snugly and level, above one knee. Be sure that the upper side of the pedometer is parallel to the ground as this will assure proper function and allow easy visual access to the display.
NOTE: Do not bend the clip excessively, otherwise it could break.
Make sure that it does not impede you while walking/running/jogging and does not hinder your natural movements. Do not attach the unit in the back pockets of your pants or the like.
5. Operation
WARNING:
Contact your physician or healthcare provider before beginning a weight reduction or exercise program.
a) Step counter function
Press the MODE button until the arrow on the display points to “St” marking. The step counter will start counting once motion is detected.
NOTE: Various movements throughout the day might be counted as a step as well, e.g. movements while sitting or up and down movements. In order to get realistic results it is recommended, to use this unit for constant activities, e.g. walking, jogging or the like.
b) Distance travelled
Press the MODE button until the arrow on the display points to “Mi”.
Press the SET button for adjusting the stride distance (i.e. the distance for each
step.) The digits on the display will start to flash.
Stride setting range: 12 inch to 60 inch; 1 inch intervals.
Press the SET button as often as necessary to adjust it to your stride length.* Once
the stride length is set, leave the unit idle for 3 seconds; it will revert back to dis­tance travelled mode.
The distance travelled counter will start counting once motion is detected.
*Finding your stride length: Take ten normal repetitive steps for the activity you are doing, marking the spot at the beginning of your first step. Measure the distance from beginning of your first step to the end of your last step. Divide this distance by ten to determine your stride length. E.g. Total distance = 370 inches; 370 inches / 10 steps = 37 inches stride length.
NOTE: Please remember that the length of your stride while walking is different than the length of your stride while running. If you plan to use this pedometer for both types of exercise, you will have to reprogram your stride length when you go from one to the other.
c) Calorie calculation
Press the MODE button until the arrow on the display points to “Kc”.
Press the SET button for inputting your body weight. The digits on the display will
start to flash.
Weight setting range: 60 lb to 300 lb, 1 lb interval.
• Press the SET button as often as necessary to adjust to your body weight value. Once
value is set, leave the unit idle for 3 seconds; it will revert back to Calorie mode.
The counter will start counting once motion is detected.
d) Auto shut off
If no motion is detected for 1 minute, the unit will automatically shut down. The val­ues on the pedometer will still be retained in memory. All functions will resume once motion is detected.
e) Viewing your Results
Repeatedly press the MODE button to cycle through the pedometer modes: STEP DISTANCE CALORIE
f) Resetting your Pedometer
Most people prefer to reset steps, distance travelled and calorie consumption back to “0” daily. To reset the values measured, press the MODE button until it reverts back to step counter mode. Press the RESET button until the digits revert back to zero.
MODE ( M )
SET ( S )
RESET ( R )
DISPLAY
BELT CLIP
YES
NO
Display Explanation
St = Steps In = Inch Lb = Pounds Mi = Miles Kc = Kcal
Features:
Step counter; up to 99,999 steps.
Distance travelled indication; up to 99.999 miles.
Calories burned indication; up to 9999.9 Kcal.
Multi-Function Pedometer
Operating and Safety Instructions
Model PE12
MODE button SET button RESET button
6. Battery
WARNING
Batteries should not be taken apart, thrown in the fire or short circuited.
This product contains a CR Type Coin Lithium Battery which contains Perchlorate Material special handling may apply: See: www.dtsc.ca.gov/hazardouswaste/perchlorate
The battery life is estimated at 2 years, depending on the frequency of use. A 1.5 V battery is permanently fitted in the pedometer. If the intensity of the display reduces or no display appears at all, have the battery changed by a specialist. For service contact see “warranty section”. Please call customer service prior to sending the unit for shipping details and terms and conditions for the battery change.
7. Changing the Measuring Unit
On delivery, your pedometer is set to the measuring units pounds and inches. This default setting can be changed to metric units (cm, Kg). Simply follow these steps to make the change: Go to Step counter mode. Press and hold the SET button until the display flashes a “0” digit.
NOTE: Changing between the units, will clear all of your pedometer’s data and set­tings. If the default setting for metric/imperial has changed, the markings on the display for distance travelled (Mi), Weight (Lb) and Step (inch) will be incorrect. For example the LCD display shows 30 cm but the indicator marking shows “inch”. The user has to bear this in mind when making the imperial/metric change.
8. Care, Maintenance and Disposal
NOTICE
The unit is not waterproof. Never immerse the unit in water or any other liquid,
touch it with wet hands, or use it in the rain otherwise liquid will enter the unit and cause damage.
Do not use any aggressive solvents, cleaning agents, detergents or any other
strong chemicals to clean the device.
Protect the unit from strong shocks (e.g. dropping the unit on the floor), direct
sunshine, high temperatures, high humidity, rain, and/or dust.
• Always dispose of the device, battery, and components in accordance with appli-
cable local regulations. Unlawful disposal may cause environmental pollution.
To keep your pedometer in the best condition and protect the unit from damage fol­low the directions below:
The pedometer should be cleaned with a soft dry cloth.
Store the unit in a safe and dry location out of reach of children.
Always use the unit following the instructions provided in this manual.
9. Troubleshooting
Possible errors Causes and correction of errors
Obscure display. Low battery. Refer to section 6 “Battery”.
Ambient temperature is too low. The normal display will recover when the temperature rises.
LCD is black. The pedometer has been exposed too long to direct sunlight
or high temperatures. It will recover to its normal status under the shade.
No display. The unit is broken. Contact customer service (see section 11
“Warranty and Service”). Battery is empty. Refer to section 6 “Battery”.
The displayed values are not correct.
Wear the pedometer properly according to the manual. You walked at an inconsistent pace. The Pedometer cannot
distinguish between short and long strides. Even the smallest step will be counted as an entire step.
You walked extremely slow. You used the unit in a place where lots of up and down
movements or vibrations take place. The set values are not correct. Check the weight and stride
settings and adjust if necessary.
The displayed values are not correct.
Default setting was changed to metric. See section 7 to change default setting to imperial units.
Pedometer was used in a vehicle, e.g. car. Vibrations might be counted as a step.
Not all your steps were detected.
Mount the pedometer properly according to the manual and ensure your walking method is correct.
10. Technical specifications
Type PE 12
Power supply 1 x 1.5 V battery (LR1130)
Measurement Range Steps: 0 to 99,999 steps
Distance travelled: 0 to 99.999 Miles (0 to 99.999 Km) Calories: 0 to 9999.9 Kcal
Setting Range
Stride length: 12 to 60 inches (30 to 120 cm),
increments 1 inch (1 cm)
Weight: 60 to 300 lb (30 to 150 Kg),
increments 1 lb (1 Kg)
Operating temperature/ Humidity
32 °F to 122 °F (0 °C to 50 °C) / 10 % to 80 % RH
Storage Temperature/ Humidity
14 °F to 140 °F (-10 °C to 60 °C) / 10 % to 80 % RH
Precision of Step counting
Within +/- 5 % for constant activities (walking, jogging or the like)*
External dimensions
1.9” x 1.9” x 0.9” (48 x 48 x 25 mm)
Weight 0.74 oz (21 g)
Subject to technical modifications. *NOTE: With other activities there might be different deviations as various move-
ments throughout the day might be counted as a step as well, e.g. movements while sitting or up and down movements. In order to get realistic results it is recom­mended, to use this unit for the constant activities mentioned above.
11. Warranty and Service
Limited Lifetime Warranty For Original Purchaser
Your Beurer pedometer, Model PE12, excluding the batteries and all accessories, is warranted to be free from defects in materials and workmanship for the life of the product under normal conditions of intended use and service. This warranty extends only to the original retail purchaser and does not extend to retailers or subsequent owners.
We will, at our option, repair or replace the Beurer pedometer, Model PE12, with­out additional charge, for any part or parts covered by these written warranties. No refunds will be given. Repair or replacement is our only responsibility and your only remedy under this written warranty. If replacement parts for defective materials are not available, Beurer reserves the right to make product substitutions in lieu of repair or replacement.
For warranty service contact our customer service department at 1-800-536-0366 or at info@beurer.com to provide a description of the problem. If the problem is deemed to be within the scope of the limited lifetime warranty, you will be asked to mail the product at your costs in its original package with proof of purchase, your name, address and phone number. If the problem is not deemed to be within the scope of the limited lifetime warranty, we will provide a quotation for repair respec­tively replacement and return shipping fee.
This warranty does not cover damage caused by misuse or abuse; accident; the at-tachment of unauthorized accessory; alteration to the product; improper instal­lation; misapplication; lack of reasonable care with respect to the product; unau­thorized repairs or modifications; improper use of power supply; old worn battery; normal wear; loss of power; dropped product; malfunction or damage of an operat­ing part as a result of failure to comply with instructions for use or to provide manu­facturer’s recommended maintenance; transit damage; theft; neglect; vandalism; or environmental conditions; loss of use during the period the product is at a repair facility or otherwise awaiting parts or repair; or any other conditions whatsoever that are beyond the control of Beurer. This warranty is void if the product is ever used in a commercial or business environment. The maximum liability of Beurer under this warranty is limited to the purchase price actually paid by the customer for the prod­uct covered by the warranty, as confirmed by proof of purchase, regardless of the amount of any other direct or indirect damage suffered by the customer.
This warranty is effective only if the product is purchased and operated in the coun­try in which the product is purchased. A product that requires modifications or adap­tation to enable it to operate in any other country than the country for which it was designed, manufactured, approved and/or authorized, or repair of products dam­aged by these modifications is not covered under this warranty.
THE WARRANTY PROVIDED HEREIN SHALL BE THE SOLE AND EXCLUSIVE WARRANTY. ANY IMPLIED WARRANTIES, OBLIGATIONS, OR LIABILITES, IN­CLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTY OF MERCHANT­ABIL- ITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE DURATION OF THIS APPLICABLE WRITTEN WARRANTY.
Some states do not allow limitations on how long an implied warranty lasts, so the above limitations may not apply to you.
IN NO EVENT SHALL BEURER BE LIABLE FOR ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS, IMPLIED OR ANY OTHER THEORY OF LIABIL­ITY, WHATSOEVER. Some states do not allow the exclusion or limitation of special,
incidental, or consequential damages, so the above limitation may not apply to you. Beurer does not authorize anyone, including, but not limited to, retailers, the subse-
quent consumer purchaser of the product from a retailer or remote purchaser, to obligate Beurer in any way beyond the terms set forth herein.
This warranty does not extend to the purchase of opened, used, repaired, repack­aged and/or resealed products, including but not limited to sale of such products on Internet auction sites and/or products by surplus or bulk resellers. Any and all war­ranties or guarantees shall immediately cease and terminate in connection with any products or parts thereof which are repaired, replaced, altered, or modified, without the prior explic- itly written consent of Beurer. This warranty gives you specific legal rights, and you may also have other rights which may vary from state to state.
For more information regarding our product line in the USA,
please visit: www.beurer.com
Beurer North America LP, Hallandale Beach, FL 33009, www.beurer.com Questions or comments? Call toll-free 1-800-536-0366 or contact info@beurer.com Made in China.
Loading...
+ 2 hidden pages