Benq Joybook S32 User Manual

Joybook S32 Series User Manual

Welcome

Copyright

Copyright 2007 by BenQ Corporation. All rights reserved. No
part of this publication may be reproduced, transmitted,
transcribed, stored in a retrieval system or translated into any
language or computer language, in any form or by any means,
electronic, mechanical, magnetic, optical, chemical, manual or
otherwise, without the prior written permission of this
company.

Disclaimer

BenQ Corporation makes no representations or warranties,
either expressed or implied, with respect to the contents hereof
and specifically disclaims any warranties, merchantability or
fitness for any particular purpose. Further, BenQ Corporation
reserves the right to revise this publication and to make changes
from time to time in the contents hereof without obligation of
this company to notify any person of such revision or changes.

Windows, Internet Explorer and Windows Mail are trademarks
of Microsoft Corporation. Others are copyrights of their
respective companies or organizations.

This product incorporates copyright protection technology that
is protected by U.S. patents and other intellectual property
rights. Use of this copyright protection technology must be
authorized by Macrovision, and is intended for home and other
limited viewing uses only unless otherwise authorized by
Macrovision. Reverse engineering or disassembly is prohibited.

Joybook models covered by
this manual

This manual contains the information about the following
Joybook models:

• Joybook S32 Series
Please note that the actual hardware or software capabilities will

vary according to the model you purchased. To determine your
Joybook model, please refer to the label on the packing box, or
the printing on your Joybook.

is a trademark of SRS Labs, Inc. TSXT technology is

incorporated under license from SRS Labs, Inc.

Table of Contents

Overview ......................................................................................... 1

About this book...........................................................................1

Typographics...............................................................................2

Getting started ................................................................................ 3

Package contents.........................................................................3

Getting your Joybook ready for use ...........................................3

Expanding the capabilities of your Joybook..............................6

Touring your Joybook.................................................................... 9

Front view....................................................................................9

Left side view .............................................................................11

Right side view ..........................................................................13

Rear view ...................................................................................14

Bottom view ..............................................................................15

Indicators...................................................................................16

Getting started with Windows Vista........................................... 18

Turning off your Joybook properly .........................................18

Using Windows Mobility Center .............................................19

Using your Joybook...................................................................... 20

Using the touchpad...................................................................20

Using the Wireless button ........................................................21

Using the keyboard ...................................................................22

Function hotkeys ................................................................22

Windows keys and lock keys .............................................. 24

Using built-in wireless connectivity (available on selected

models)......................................................................................26

Connecting to a wireless network:..................................... 26

Using Bluetooth (available on selected models)..................... 28

Connecting to a Bluetooth device ..................................... 28

Sending a file to a Bluetooth device .................................. 32

Using QMedia Bar.................................................................... 34

Introduction to QMedia Bar ............................................. 34

Setting up QMedia Bar ...................................................... 34

Using QEye ............................................................................... 35

Using WebCam Companion ............................................. 35

Main screen .................................................................. 35

Capturing images or recording videos........................ 36

Monitoring ................................................................... 37

Video conferencing...................................................... 37

Using QShot.............................................................................. 37

Capturing real-time images from QEye............................ 37

Capturing still images from movies .................................. 37

Capturing desktop images ................................................. 38

Changing the location of the media folder ....................... 38

Using BenQ Surround.............................................................. 38

Using BIOS setup ......................................................................... 39

When and how to use BIOS setup........................................... 39

Main menu ......................................................................... 40

Security menu..................................................................... 41

Boot menu .......................................................................... 41

Exit menu............................................................................ 42

Boot from LAN......................................................................... 42

Recovering your system ............................................................... 43

Table of Contents iii

Using QDataTrove ....................................................................43

Launching QDataTrove:.....................................................43

Backing up your files: ...................................................43

Recovering your backup files: ......................................44

Restoring your backup image: .....................................44

Restoring your Joybook to factory default settings:....44

Recovering your system using the supplied discs....................45

Step 1: Reinstalling a clean copy of Windows Vista..........45

Step 2: Reinstalling drivers and applications.....................46

Protecting your Joybook from viruses and other security

threats ........................................................................................46

Connecting to external display devices....................................... 47

Connecting to a VGA display device........................................47

S-Video output..........................................................................48

Adjusting video standards manually..................................49

Installing additional memory...................................................... 51

FAQ and troubleshooting ............................................................ 54

General.......................................................................................54

Battery and power .....................................................................54

Connection ................................................................................56

System ........................................................................................57

Display .......................................................................................61

Cleaning and battery maintenance ............................................. 63

Battery maintenance .................................................................63

Cleaning your Joybook .............................................................63

Service and support...................................................................... 64

BenQ Joybook Global Online Service ......................................64

Joybook Overseas Regional Warranty (ORW) online

registration.................................................................................64

Appendix....................................................................................... 65

General safety information....................................................... 65

Safety information about the battery....................................... 65

Safety information about the power adapter .......................... 66

Safety information about the modem ..................................... 66

Caution ............................................................................... 66

Disposal of Waste Electrical and Electronic Equipment

by users in private households in the European Union. ........ 66

Declaration of Conformity....................................................... 67

Safety instructions for Poland, Romania, Slovenia, Bulgaria,

Latvia, and Croatia.................................................................... 68

Table of Contentsiv

Overview

About this book

This book provides you the main information about various
components in your Joybook and demonstrates how to use
them. The following are the major chapters of this book.

Chapter title Description

Overview Introduction to this book.

Getting started Information about beginning to

use your Joybook.

Touring your Joybook Introduction to the hardware

components of your Joybook.

Getting started with
Windows Vista

Using your Joybook Basic and advanced

Using BIOS setup Information about how to use

Recovering your
system

Basic information about
Windows Vista.

information about operating
your Joybook.

the BIOS setup utility.

Information about using system
recovery tools.

Connecting to

external display

devices

Installing additional

memory

FAQ and

troubleshooting

Cleaning and battery

maintenance

Service and support Joybook service and support

Appendix Important safety information.

Information about how to
connect your Joybook to
external display devices.

Information about how to add
additional RAM memory.

Information about frequently
asked questions and
troubleshooting.

Information about cleaning and
battery maintenance.

information.

Overview 1

Ty po g ra ph ic s

The usage of notes, tips and warnings in this manual is
specifically for different purposes, which are described as
follows:

Icon/
Symbol

< > or [ ] Keys on the

Item Meaning

Warning Information mainly to

Tip Useful information for

Note Supplementary information.

keyboard; User
Interface (UI)
on the screen

prevent the damage to
components, data, or
personal injury caused by
misuse and improper
operation or behavior.

completing a task.

Indicates a key on the
keyboard, or the UI on the
screen. Do not actually type
the symbols together with
the enclosed letters.

Overview2

Getting started

Depending on the model of your Joybook, the appearance may
be different from the illustrations shown in this manual.

Package contents

Before using your Joybook for the first time, please check if you
have all the items with you. For details about what should be
included in the package, refer to the Package Contents label
inside the accessory box. If any of the items are missing or
appear damaged, contact your dealer immediately. Save the
packaging in case you need to ship your Joybook for service.

Getting your Joybook ready for use

1. Installing the battery pack

Battery retainer A

Close the lid of your Joybook (if open). Turn your Joybook
upside down and place it on a soft clean cloth. With the label
side of the battery pack facing down, slide it gently into the
battery compartment until it snaps into place (1). Move the
battery retainer A to the left as shown to lock the battery pack
into place (2).

Getting started 3

2. Connecting the power

Connect the power cord to the power adapter.

Connect the power adapter to the power socket on your
Joybook.

• Power systems and plug types may vary depending on your
country/region.

• When the battery is charging, the battery indicator appears in
amber. When the battery is fully charged, the light goes off.

• For details about the colors and meanings of the indicators,
refer to "Indicators" on page 11.

3. Opening your Joybook

Connect the power cord to a wall outlet. The Joybook will
automatically start charging the battery.

• The battery pack is shipped with low charge from the factory.
You can still use your Joybook while the battery is charging.

Getting started4

Gently lift up the latchless lid that allows you to open the case
easily.

4. Performing initial setup

Press the Power button to start up your Joybook, and then
follow the on-screen instructions to complete the initial
Windows Vista setup.

• Your Joybook S32 Series works best with Windows Vista™
Home Basic, Windows Vista™ Home Premium, Windows
Vista™ Business, or Windows Vista™ Ultimate. Installing
other operating systems that have not been tested is not
recommended, and may not only void your warranty but also
affect the functionality of your Joybook.

• The actual operating system that comes with your Joybook
may vary. For details, refer to the Product Specification label
on the product carton.

Getting started 5

Expanding the capabilities of your Joybook

Connect an external display device (such as a monitor or
projector) to the 15-pin D-sub video socket of your Joybook.

Connect a telephone line to the modem port of your Joybook
and dial-up to the Internet or send a fax.

Getting started6

Access local area network (LAN) by connecting a network cable
to the LAN port of your Joybook.

Insert an ExpressCard/34 module or ExpressCard/54 module to
further expand the capabilities of your Joybook.

Use the optical drive to access data on various kinds of discs and
enjoy movies or music.

Connect a microphone to the microphone input socket to
record sounds.

Connect an earphone to the audio output socket to output
sounds.

Insert a Memory Stick, Memory Stick Pro, SD, MMC, or xD
memory card following the direction indicated on the card to
exchange files.

Getting started 7

Connect digital camcorders and high-speed storage equipment
to this IEEE 1394 (FireWire) Port.

Connect USB peripherals to the USB port of your Joybook.

Getting started8

Output video images on your Joybook to a TV or A/V device
that has an S-Video Input socket by connecting it to the S-Video
Out socket on your Joybook.

Unless you intend to use the sound reproduction output of the
built-in Joybook speakers, you will also need to separately
connect the Joybook audio output socket to an appropriate
sound reproduction device.

Tou ring your Joy b ook

Front view

(1)

(2)

(3)

S32

(11)

(12)

No. Front components

(1) Built-in camera (QEye)

A 1.3 megapixel built-in camera (QEye) that
allows you to hold a video conference, capture
images, or record videos. For details, refer to

"Using QEye" on page 35.

(2) Power and quick access buttons

Power button

Turns your Joybook on or off.

QShot

Allows you to capture desktop images, still images
from movies, and real-time images from QEye,
with one touch. For details, refer to "Using QShot"

on page 37.

BenQ Surround

Allows you to turn on or turn off SRS TruSurround
XT in your Sound Manager with one touch.

(4)

(3) Keyboard

(4) Touchpad

Refer to "Using the touchpad" on page 20 for
details.

(5) (6) (7) (8) (9) (10) (5)

(5) Speakers

Touring your Joybook 9

(6) Indicators

Refer to "Indicators" on page 16 for details.

(7)

Wireless button

Press this button to activate/deactivate wireless
devices like Bluetooth and WLAN. Make sure this
button is "ON" before using <Fn> + <F12>. For
details, refer to "Using the Wireless button" on

page 21.

(10)

Five-in-One memory card slot

For a Memory Stick, Memory Stick Pro, SD, MMC,
or xD memory card.

(11) LCD (Liquid Crystal Display) panel

(12) Built-in microphone

Receives sounds and voices for recording.

(8)

Earphone/SPDIF audio output socket

Can be used to connect to an earphone/headset
or external speaker for playing the Joybook audio.

SPDIF (Sony-Philips Digital Interface Format) is a
fibre optic digital audio outlet for 'Mini Optical'

3.5mm plugs. It shares a common socket in the
Joybook with a standard analog audio outlet for

3.5mm stereo plugs.

• To activate SPDIF, go to Control Panel, Hardware and
Sound, and select Sound. Select SPDIF Interface
under the Playback tab, click Set Default, and then
click OK.

• Supported digital audio formats: DTS, Dolby Digital,
and Microsoft WMA Pro Audio.

(9)

Microphone input socket

Can be used to connect to a microphone for
recording sounds.

This socket is for 3.5mm analog audio plugs. It

accepts both mono and stereo plugs.

Touring your Joybook10

Left side view

(1) (2) (3) (4) (5) (6) (7)

No. Left-side components

(1) Power socket

For connecting AC power supply to power the
Joybook and charge the battery.

(2)

15-pin D-sub video socket

For connecting external display devices, such as
monitors and projectors.

(3)

S-Video Out socket

Allows the Joybook to output video signals to S­Video capable devices, such as a television set or
VCR.

For details, refer to "S-Video output" on page 48.

Touring your Joybook 11

(4)

LAN (Local Area Network) port (RJ-45

connector)

Allows the Joybook to connect to a 10/100/
1000Mbps fast Ethernet 1000BASE-T network.

Please be careful to avoid plugging a RJ-11 phone
cable connector in the RJ-45 port. This will damage the
LAN port. They look similar, but the RJ-45 connector is
wider than the RJ-11 connector, and has more
conductors.

(5)

USB ports

For connecting peripherals such as mice, digital
cameras and MP3 players that use the USB 2.0
interface.

(7) ExpressCard slot

This ExpressCard slot accepts two formats of the
standard ExpressCard modules: ExpressCard/34
and ExpressCard/54. The ExpressCard/34
module is characterized by its 34 mm width, and
the ExpressCard/54 module is characterized by its
54 mm width. You can use an ExpressCard to
further expand the capabilities of your Joybook.

Insert an ExpressCard into the slot following the
direction indicated on the card and complete
related driver settings.

(6)

IEEE 1394 (FireWire) port

For connecting high-speed peripherals, such as
digital video cameras and other consumer
electronics devices that use the IEEE 1394
(FireWire) interface.

Touring your Joybook12

Right side view

S32

(1) (2) (3) (4) (5) (6)

No. Right-side components

(1)

Modem port (RJ-11 connector)

Accepts an analog telephone line for use with the
internal modem.

• To reduce the risk of fire, ensure that your phone
cable is of adequate capacity and approved for use
with your local telecommunications supplier.

• This is the only telecommunications modem port on
the Joybook. Please be careful to avoid plugging a
narrow RJ-11 phone cable into the similar looking but
wider RJ-45 LAN port on the left side of the Joybook.

(2) DVD/CD-RW Combo/DVD Super-Multi drive

(available on selected models)

The type of the optical drive varies by model, and the
support of disc types depends on the optical drive that
comes with your Joybook.

Supports multi-functional optical module for
reading music CDs, VCDs and DVDs or burning
CD-R/CD-RW or DVD+R/DVD-R/DVD+RW/DVD­RW/DVD-RAM (optional) discs. Discs can be
inserted/ejected by pressing the small ejection
button on the drive.

Touring your Joybook 13

(3) Optical drive ejection button

Discs can be inserted/ejected by pressing this
ejection button.

(4) Manual tray opening

If you wish to open the disc tray when your
Joybook power is off, or it can't be opened using
the ejection button, insert a pointed object (like an
opened paper clip) into the tray ejection hole next
to the ejection button to release the disc tray.

Rear view

(1)

(5)

(6)

Touring your Joybook14

USB ports

For connecting peripherals such as mice, digital
cameras and MP3 players that use the USB 2.0
interface.

Anti-theft Kensington lock slot

You can attach an anti-theft Kensington lock and
cable to this slot to help prevent possible theft.

No. Rear components

(1) Ventilation holes

For dissipating heat and keeping your Joybook at
an optimal temperature.

To prevent overheating, do not obstruct the vent. For
example, do not use the Joybook in bed where a
blanket may inadvertently cover the vent and block the
airflow.

Bottom view

No. Bottom components

(1) Battery retainer A

Secures the battery in place.

(2) Battery pack

Supplies power to the Joybook when external
power is not connected.

(3) Battery retainer B

Secures the battery in place.

(4)

(1) (2) (3)

(4) MiniCard and memory expansion slot cover

Inside the cover, you can find the memory slot of
the Joybook. There is also a MiniCard slot for
using an optional MiniCard.

• A wireless network card in the MiniCard form-factor
design may have been pre-installed on selected
models.

• To remove the cover, a small Phillips head screwdriver
is required.

• For more information about adding additional
memory, the limit of maximum memory, or the types
of BenQ certified memory modules for your Joybook,
refer to "Installing additional memory" on page 51.

Touring your Joybook 15

Indicators

(1) (2) (3) (4) (5)

No. Indicators

(1) Power button indicator

• When the system is on, it lights up in blue.

• When the system is in Standby, it lights up in
amber.

• When the system is off or in Hibernation, the light
goes off.

(2)

(3)

Touring your Joybook16

Hard disk/optical drive activity indicator

Flashes in blue when the Joybook is accessing
data in the hard disk drive or optical drive.

Caps Lock indicator

Lights up in blue when the Caps Lock is activated.

(4)

(5)

Scroll Lock indicator

Lights up in blue when the Scroll Lock is activated.

Num Lock indicator

Lights up in blue when the Num Lock is activated.

(6) (7) (8)

No. Indicators

(6)

Battery indicator

• When the system is on and the battery is in use,
it lights up in blue.

• When the battery is charging, it lights up in
amber.

• When the battery is fully charged, and the
system is on and connected to the power source,
the amber light goes off.

• Flashing blue indicates that the battery is running
low.

• Flashing amber indicates that the battery is
malfunctioning, in which case you should contact
service personnel.

(7)

Five-in-One memory card access indicator

Flashes in blue when accessing a Memory Stick,
Memory Stick Pro, SD, MMC, or xD memory card.

(8)

Wireless button indicator

• When the wireless LAN is turned on, it lights up
in blue.

• When Bluetooth is turned on, it lights up in
amber.

• When the wireless LAN and Bluetooth are both
turned on, it lights up in purple.

• When the wireless LAN and Bluetooth are both
turned off, the light goes off.

For details about using the Wireless button, refer to

"Using the Wireless button" on page 21.

Touring your Joybook 17

Getting started with Windows Vista

Depending on your purchased model, your Joybook may come
pre-installed with the latest Microsoft operating system:
Windows Vista™ Home Basic, Windows Vista™ Home
Premium, Windows Vista™ Business, or Windows Vista™
Ultimate.

When you first set up your Joybook, you may want to find
information about the following topics. Refer to the user
manual that is supplied with your operating system, or search
from Help and Support in the Start menu.

• How to set the system region settings, date, and time.

• How to set system administrator and user security logins and
settings.

• How to install, setup and run anti-virus software.

• How to name the computer for network identification.

• How to connect to a local network wirelessly or by cable.

• How to connect to another computer over a network and share
files.

• How to connect with a network or shared printer.

• How to connect to the Internet.

• How to register Windows and other packaged software.

• How to update Windows with the latest service packs and
security patches.

• How to synchronize the system clock with an Internet time
server.

Getting started with Windows Vista18

• How to locate, download, and install latest system device
drivers.

• How to setup scheduled events for system maintenance.

Tur nin g of f your Joybo ok properly

By Windows default, the Start menu power button puts
your Joybook into sleep. Therefore, if you wish to turn off the
power of your Joybook completely, click the Start menu, click
the arrow next to the Lock button, and then click Shut Down.

Alternatively, you can customize the function of the Start menu
power button by following the steps below.

1. Right-click the battery meter icon ( or ) in the

notification area located in the lower right corner of the
desktop, and then click Power Options.

2. On the Select a power plan screen, click Change plan settings

under the selected plan.

3. Click Change advanced power settings.

4. On the Advanced settings tab, double-click Power buttons
and lid to expand this category.

5. Then, double-click Start menu power button to expand this
item.

6. To specify the action to take when you press the Start menu
power button, click On battery or Plugged in, and then select
the desired setting from the drop-down list.

The Start menu power button may look different according to
your settings

Appearances Functions

Puts your Joybook into sleep.

Shuts down your Joybook.

Installs the Windows updates when
available, and then shuts down your
Joybook after the installation is
complete.
This form of power button is only
available when you’ve set your
Joybook to receive updates
automatically.

Using Windows Mobility Center

Windows Mobility Center is a convenient location where you
can quickly access your Joybook's settings, such as brightness,
volume, battery status, and wireless network, etc.

To open Windows Mobility Center, press the <Fn> + <F10>
hotkey combination, or do one of the following:

• Click Start, Control Panel, Mobile PC, and then click Windows
Mobility Center.

• Click the battery meter icon ( or ) in the notification
area located in the lower right corner of the desktop, and then
click Windows Mobility Center.

Getting started with Windows Vista 19

Using your Joybook

Using the touchpad

The touchpad with its buttons is a pointing device that
functions as an optional external mouse, which can perform
navigation, scrolling and selection functions. The components
of the touchpad are described as follows.

No. Component Function

(1) Touchpad Moves the pointer, selects or

activates items on the screen.

(2) Left touchpad

button

(3) Right touchpad

button

• To use the touchpad as an optional external mouse, press the
left and right touchpad buttons, which provide the same click
functions as an external mouse does.

• To move the pointer, place your finger with slight pressure on
the touchpad and move in the direction as desired.

• Do not use a pen, pencil, or marker on the touchpad. Use only
your fingertip.

• To set the touchpad preferences in Microsoft Windows Vista,
select Start, Control Panel, Hardware and Sound, and Mouse.

Equivalent to the left button of
an optional external mouse.

Equivalent to the right button
of an optional external mouse.

Using your Joybook20

Function Left

touchpad
button

Right
touchpad
button

Touchpad

Select Click once. Tap once.

Execute Click twice

quickly.

Drag Click once

and hold the
item, and
then use
your finger
on the
touchpad to
drag.

Tap twice
quickly.

Tap twice
quickly and
hold the
item, and
then move
your finger
on the
touchpad to
drag.

Display

Click once.
the
context
menu

The touchpad is a pressure sensitive device that requires
proper care to avoid damage.

• Do not rest heavy objects on the touchpad or its buttons.

• Do not scratch the touchpad with sharp-pointed objects or
your fingernails.

Using the Wireless button

The Wireless button allows you to turn on or turn off the
wireless radio. By default, the button is "OFF" when your
Joybook starts up.

Before using wireless devices like Bluetooth and WLAN, be sure
to press this button to turn on the wireless radio first, and then
use the <Fn> + <F12> hotkey combination to switch between
Bluetooth and WLAN.

WLAN and Bluetooth are available on selected models.

• If the Wireless button is "ON", the indicator may light up in
blue, amber, or purple, depending on the on/off status of
Bluetooth and WLAN. Refer to "Indicators" on page 16 for
details.

• If the Wireless button is "OFF", the indicator goes off. And you
will not be able to use the <Fn> + <F12> hotkey combination to
switch Bluetooth/WLAN on or off.

Using your Joybook 21

Using the keyboard

Function hotkeys

You can use the function hotkeys to access commonly used functions or make quick settings. To use the hotkeys, press and hold the
<Fn> (Function) key at the lower left corner of the keyboard, and then press the desired hotkey.

The appearance of the keyboard legend may vary depending on the country/region of your purchase.

Using your Joybook22

Function hotkey Description Function hotkey Description

<Fn> + <F1> Opens function hotkeys online help. <Fn> + <F8> Decreases volume.

<Fn> + <F2> Puts your Joybook into sleep mode. <Fn> + <F9> Increases volume.

<Fn> + <F3> Switches display between the screen

and an external monitor/projector, or
allows simultaneous display; switches
between internal/external display.

<Fn> + <F10> Launches Windows Mobility Center.

For details about using Windows Mobility
Center, refer to "Using Windows Mobility

Center" on page 19.

<Fn> + <F4> Decreases screen brightness. <Fn> + <F12> Switches between all 3 combinations of

WLAN and Bluetooth on/off. The status is
indicated by the on-screen display.

WLAN and Bluetooth are available on
selected models.

Make sure the Wireless button is "ON"

before using this function hotkey.

<Fn> + <F5> Increases screen brightness. <Fn> + <Scr Lk> Activates or deactivates the scroll lock

function. When activated, the screen
moves one line up or down when you
press the up or down arrow key (, ).

Scroll Lock does not work in all
programs.

<Fn> + <F6> Activates or deactivates the touchpad. <Fn> + <Prt Sc> Copies a bitmap image of the current

entire screen to your clipboard, which can

<Fn> + <F7> Activates or deactivates the speakers.

be inserted into documents as a
screenshot, or pasted into a graphics
software, such as Microsoft Paint.

Using your Joybook 23

Windows keys and lock keys

Using your Joybook24

Function hotkey Description Function hotkey Description

+ Tab

+ E

+ M

Shift + + M

Windows key

Functionally equivalent to clicking the
Start button on the Windows desktop.

Press and hold the Windows key, and
then press Tab to switch between
windows.

Opens the Computer window for
browsing disks and files.

Minimizes all windows.

Cancels minimization of all windows.

+ R

Activates the Run dialog box.

Num Lk Activates or deactivates the numeric

keypad integrated in the keyboard
(indicated by the light gray shade in
the illustration on the previous page).

Caps Lock Capitalizes all text entered.

Application key

Provides the same function as the
right touchpad button, bringing up a
contextual pop-up menu.

Using your Joybook 25

Using built-in wireless connectivity (available on selected models)

With the built-in wireless connectivity of your Joybook, you can
access other wireless network enabled devices (such as Access
Point network stations, Notebook computers, Personal Digital
Assistants, or digital projectors) wirelessly without the
constraints of network cables.

To connect with a Local Area Network (LAN) at home or in the
office, you need the details of an access point, which serves as an
air station to make transmission possible. Outdoors in places
such as in coffee shops or library, you can inquire the service
personnel about an account.

• Wireless LAN (WLAN) is available on selected models.

• WLAN connectivity has limited range, depending upon the
equipment being used, the chosen frequency band, radio­wave interference, and the physical landscape (including
building structure). Circumstances will vary depending upon
your particular situation.

Connecting to a wireless network:

1. Make sure you are located within the wireless network service

area.

2. Press the Wireless button on your Joybook to enable
the WLAN.

3. The status is indicated by the on-screen display as follows.

4. Click on the WLAN icon in the notification area located
at the lower right corner of the desktop to display a pop-up

menu.

5. From the pop-up menu, click Connect to a network.

Using your Joybook26

6. Click Wireless in the Show list. A list of available wireless
networks will be displayed.

7. Click a network and then click Connect. If security
authentication is not required by the network you are using,
there will be a successful message showing that you have
connected to the network.

• To connect to some networks that require security

authentication, you may have to undergo another
authorization process and enter username and password. For
details, please consult your network administrator.

• For further information, refer to Help and Support in Windows

Vista.

• For data security, it is strongly recommended to connect to

security-enabled wireless networks whenever possible.

• When travelling by air, please be sure to turn off wireless

networking to avoid any possible risks to flight safety.

There are other ways for the Joybook to connect with a network.
See "LAN (Local Area Network) port (RJ-45 connector)" and

"Modem port (RJ-11 connector)".

Using your Joybook 27

Using Bluetooth (available on selected models)

The Bluetooth function allows you to get connected to various
devices and services that support Bluetooth transmission. You
can connect wirelessly without the need for data cables when
printing documents, synchronizing your Personal Information
Management (PIM) data with your Personal Digital Assistant
(PDA) or another Personal Computer (PC), mobile phone or
even sharing a network connection.

Bluetooth is available on selected models.

Connecting to a Bluetooth device

1. Make sure the Wireless button on your Joybook is
"ON".

• If the Wireless button is "ON", the indicator may light up in

blue, amber, or purple, depending on the on/off status of
Bluetooth and WLAN. Refer to "Indicators" on page 10 for
details.

• If the Wireless button is "OFF", the indicator goes off. And you

will not be able to use the <Fn> + <F12> hotkey combination to
switch Bluetooth/WLAN on and off.

2. Press the <Fn> + <F12> hotkey combination a few times
until Bluetooth is "ON".

• The maximum effective range of connection between your
Joybook and the Bluetooth device is 10 meters.

4. Right-click on the Bluetooth icon in the notification area

located at the lower right corner of the desktop, and then
click Add a Bluetooth Device to launch the wizard.

3. Turn on the power of your Bluetooth device and activate its
Bluetooth function. You also need to make your Bluetooth
device "Discoverable".

• For details about how to activate the device's Bluetooth

function, please refer to its documentation.

Using your Joybook28

5. If your Bluetooth device is already turned on and
discoverable, place a check mark in the My device is set up
and ready to be found checkbox, and then click Next.

6. Please wait while Windows is searching for available
Bluetooth devices.

Using your Joybook 29

7. Select the Bluetooth device that you want to add, and then
click Next.

8. Refer to the documentation that came with your Bluetooth
device to determine if there is a pre-defined passkey. If not,
you can select Choose a passkey for me.

Using your Joybook30

9. Windows will generate a passkey. When you are prompted to
enter a passkey on your Bluetooth device, follow the on­screen instructions to enter the passkey.

10.The Bluetooth device is now connected to your Joybook.
Click Finish to complete.

Using your Joybook 31

Sending a file to a Bluetooth device

If your Bluetooth device is capable of sending and receiving
data, such as a mobile handset, you can use the Bluetooth
connectivity to transfer data wirelessly between your Bluetooth
device and Joybook.

1. After your Joybook is connected to a Bluetooth device, right­click the Bluetooth icon in the notification area to
display the pop-up box, and then select Send a File.

2. Click Browse to select the location to which you want to send
the file, and then click Next to continue.

Using your Joybook32

3. The file will be sent to the location you specified. 4. Click Finish to complete.

The example shown above is specifically for connecting to a
mobile handset. To connect to other types of Bluetooth devices,
refer to the online Help for details.

Using your Joybook 33

Using QMedia Bar

Introduction to QMedia Bar

QMedia Bar integrates a number of

software applications to enhance the multimedia experience on
your Joybook. Click on the small triangle button and a

rotating button bar will display.

Setting up QMedia Bar

Right-click on QMedia Bar and a menu will display on it.

You ca n:

• Let QMedia Bar display on top of all open programs by
selecting Always on top.

• Close QMedia Bar by selecting Exit.

• Adjust the size of QMedia Bar on the screen by selecting Size
and then select an appropriate value.

Using your Joybook34

Using QEye

Your Joybook comes with a 1.3 megapixel built-in camera
(QEye) on the inside top of the lid, above the screen. With QEye,
you can capture images, record videos, and also hold a video
conference.

Using WebCam Companion

'WebCam Companion' features four modules below that helps
you get the most out of your QEye.

• Capture: allows you to capture a still image and video from
QEye.

• Monitor: detects any movement that is visible to QEye and
records it automatically.

• Browse: allows you to edit a previously captured image or
video.

• Chat: gives you quick access to a variety of instant messaging
programs that support video conferencing.

Main screen

The Main screen in any module contains the following icons
and menus.

Icon Name Description

Home Returns to the Home

screen to select other
modules.

Shows the current
module. To switch to
another module, click
the arrow to display a
drop-down menu.

E-mail Attaches the selected

files to an e-mail.

Slide Show Runs a slide show of

the selected images.

Print Prints the selected

images.

Using your Joybook 35

Settings Adjusts the capture

settings, such as file
format, resolution,
audio devices, video
devices, etc.

WebCam
Settings

Views and modifies
your QEye’s settings
and properties.

Full Screen Displays the current

video or live preview
in full screen. To exit,
press the <Esc> key
or click the Close
button

Disconnect Disconnects QEye.

Connect Connects QEye.

Capturing images or recording videos

1. Launch 'WebCam Companion' by following one of the ways
described below.

• Click Start, All Programs, the Web C am C o mpa nio n
folder, and then click Web Ca m Co mp a ni on .

• Click the WebCam Companion button on QMedia Bar.

2. Click to select the Capture module from the Home screen.

3. On the Capture preview screen, you can do the following
tasks.

• Capture: captures a still image from QEye.
Alternatively, you can also press the QShot button

to capture a still image.

• Burst: captures multiple images in quick succession.
The number of images to be captured in each burst can
be defined in Settings.

• Record Video: begins capturing video from your QEye.

The image and video files will be saved to a QShot folder that
is placed on your desktop by default.

• The snapshot resolution is set to 640 x 480 by default. To
change the setting, click Settings.

• You can preview the captured images in the thumbnails area.

• For more information, refer to Help topics in WebCam
Companion, by clicking the Help menu and selecting
Application Help, or pressing the <F1> key.

The background affects picture clarity and light level, and the
resultant image quality.

Using your Joybook36

Monitoring

The Monitor modules detects any movement that is visible to
QEye and records it automatically. An e-mail or text message
alert will be sent at the same time. You can even have the
snapshots uploaded to an FTP site automatically.

1. Launch 'WebCam Companion'.

2. Click to select the Monitor module from the Home screen.

3. On the Monitor screen, click Monitor Settings to view and
modify your settings first.

4. When you are finished with the settings, click Start Monitor
to begin monitoring. When movement is detected, recording
begins automatically.

5. Click Stop Monitor when you want to stop monitoring.

6. Click Record Video under the Capture tab.
The video file will be saved to a QShot folder that is placed on
your desktop by default.

The recorded video logs will be stored in Log Albums.

Video conferencing

To hold a video conference, click to select the Chat module from
the Home screen, and then install a free instant messaging
program provided. Follow the on-screen instructions to
complete the installation.

You can use 'WebCam Companion' with 'Magic-i' to enhance
the video conferencing experience. Use a rich set of effect
templates to make video conferencing fun and entertaining. To
launch 'Magic-i', take the following steps.

1. Click Settings on the Main screen.

2. On the Capture Settings screen, click the drop-down list
under Video device to select ArcSoft Magic-i Capture.

3. Click OK.

You can also click the Start Face Tracking icon in 'Magic-i'
to keep your face tracked and in the center of the video frame.

Using QShot

QShot is a quick access button on your Joybook that allows
you to capture desktop images, still images from movies, and

real-time images from QEye, with one touch.

With QShot, you do not need to use the Print Screen key, and
save to file anymore. This operation can be done easily in one
touch by using QShot. By default, the captured image files will
be saved to a media folder named "QShot" on the desktop. To
change the location of the media folder, refer to "Changing the

location of the media folder" on page 38.

Capturing real-time images from QEye

1. Launch 'WebCam Companion'.

2. Make sure 'WebCam Companion' is the active window.

3. Press the QShot button.

4. The captured image file will be saved to a QShot folder.

Capturing still images from movies

1. Load a DVD/VCD movie into your optical drive and launch
an application to play the movie.

2. Under the active window, press the QShot button.

3. The captured image file will be saved to a QShot folder.

• The size of the captured image depends on the window size.

• QShot does not support screen overlay capture capability.

Using your Joybook 37

Capturing desktop images

1. Place your cursor on the desktop.

2. Press the QShot button.

3. The captured image file will be saved to a QShot folder.

Changing the location of the media folder

1. In 'WebCam Companion', click the Preferences menu, and
then click Media Folder. A Media Folder screen will be
displayed.

2. Click Browse to select a folder where you want to store your
captured image files, and then click OK.

3. Click OK to close the Media Folder screen.
The captured image files will be saved to the new location.

Using BenQ Surround

BenQ Surround is a quick access button on your Joybook
that allows you to turn on or turn off SRS TruSurround XT in
your Sound Manager with one touch.

To adjust the advanced settings, double-click the icon in the
notification area of your desktop, click the Speakers tab, and
then click the SRS tab.

Using your Joybook38

Using BIOS setup

BIOS (Basic Input/Output System) is a layer of software, called
firmware, that translates instructions from other layers of
software into instructions that the Joybook hardware can
understand. The BIOS settings are needed by the Joybook to
identify the types of installed devices and establish special
features.

BIOS settings are specific to your Joybook hardware. Do NOT
change existing BIOS settings unless you are sure they need to
be changed, and are aware of the consequences. Any incorrect
BIOS settings may degrade the performance, operation and
functionality of your Joybook.

For latest BIOS updates, visit http://Support.BenQ.com.

When and how to use BIOS setup

You need to use BIOS setup when:

• You see an error message on the screen requesting you to run
BIOS setup.

• You want to restore the factory default settings.

• You want to modify some specific settings according to the
hardware.

• You want to modify some specific settings to optimize system
performance.

• The BIOS setup screen shown in this chapter is for your
reference only. The actual items or settings on your Joybook
may differ.

• The BIOS setup program may have been updated after the
publication of this manual.

• The settings you select in your operating system might
override similar settings in BIOS setup.

To run BIOS setup, press the <F2> key immediately when the
BenQ logo appears on the screen during system startup. The
logo shows up on the screen for only a few seconds, so you must
press the <F2> key at the time. The BIOS setup main screen will
appear as follows.

Using BIOS setup 39

The BIOS setup screen can be divided into four areas:

• On the top line is the menu bar containing the titles of
available menus. Each menu title contains a specific menu.

• The center left column of the menu contains information
regarding the current settings of the system. If you open a pull­down menu and select an item that provides multiple options,
the left column will display a submenu where you can make
further selections.

• The right column of the menu contains Help information
about the current menu selected. When a menu item is
highlighted, more detailed information is given.

• The bottom lines of the menu provide keyboard instructions
for moving around and making selections.

Navigating the BIOS setup screen

Keyboard information can be found at the bottom of the screen.
A brief description of keyboard usage is listed below:

Key Function

Left and right
arrow keys (, )

Up and down
arrow keys (, )

Enter • Displays the sub-menu when an

Selects a menu title.

Selects an item or option.

item with the arrow sign is
selected.

• Opens or closes the option
window when an item is selected.

Tab Jumps from one item to another.

Esc • Exits BIOS setup.

• Returns to the previous menu if
in a sub-menu.

• Closes the options window if one
is open.

Main menu

The Main menu contains the basic configuration settings of the
system and shows some system information, such as the BIOS
version, CPU type and speed, and the system memory, etc.

• System Time: allows you to set the time of the system. Type in
the value and then press <Enter>, <Tab> or <Shift> + <Tab>
to change the next value.

• System Date: allows you to set the date of the system. Type in
the value and then press <Enter>, <Tab> or <Shift> + <Tab>
to change the next value.

• Advanced Configuration: contains the I/O (Input/Output)
configuration settings of the system for advanced users. There
are 3 items included as follows.

a. Quiet Boot: This item controls the display of BenQ

logo during system boot.

• When enabled, BenQ logo will be displayed during
system boot.

• When disabled, diagnostic texts will be displayed
during system boot.

b. Legacy USB Support: This item allows the support of

legacy USB devices during system boot and under
DOS.

Using BIOS setup40

c. CPU Power Saving: This item determines if the CPU

supports enhanced C-state, which determines the
power management of CPU.

If you are not familiar with the items in Advanced Configuration
menu, you are advised to keep the default.

Security menu

The Security menu contains the security settings, which
safeguard your system against unauthorized use.

Do NOT set the BIOS security password without having
memorized it or written it down and stored it with your Joybook
warranty documentation. Should you happen to forget or mislay
the password once set, you will be greatly inconvenienced in
gaining subsequent access to your Joybook.

• Set Supervisor Password: This set of password controls access
to the whole BIOS setup menu. It must be set before User
Password can be set. When typing the password, first make
sure Num Lock is off, and then type your password in the
entry fields and press <Enter>. Confirm your password by
typing it again and pressing <Enter>.

• Set User Password: This set of password controls access to part
of the BIOS setup menu.

• Password on boot: This item determines if a password will be
prompted during system boot. When this item is enabled, the
password is always required to boot the computer.

If Set Supervisor Password and Set User Password are both set,
you can enter either one of them during the password prompt.
To have full privileges in BIOS setup, enter Supervisor
Password.

Boot menu

The Boot menu contains the boot configuration settings of the
system. A list of devices will be displayed under Boot Sequence.

• Use <> or <> to select a device, and then press <F6> to
move it up or <F5> to move it down.

• To select a boot device manually, press the <F9> key when the
BenQ logo appears on the screen during system startup. The
Boot Menu will appear. Use the up and down arrow keys (,
) to select a boot device, and then press <Enter> to confirm.

Using BIOS setup 41

Exit menu

The Exit menu displays ways of exiting BIOS setup. After
finished with your settings, you must save and exit so that the
new settings can take effect.

• Exit Saving Changes: saves the changes you have made and
exits BIOS setup. After finishing with your settings, you must
save and exit so that the new settings can take effect.

• Exit Discarding Changes: exits BIOS setup without saving the
changes you have made.

• Load Setup Defaults: loads factory default values for all the
items.

• Discard Changes: cancels all changes since last save, without
exiting the BIOS setup utility.

• Save Changes: saves changes without exiting the BIOS setup
utility.

It is recommended that you go into BIOS to load setup defaults,
whenever you have installed new hardware components.

Boot from LAN

During system startup, pressing <F12> will activate Boot from
LAN feature, enabling your Joybook to boot from an OS image
via the network.

Using BIOS setup42

Recovering your system

System recovery is a data destructive process. You should
backup all data and applications prior to restoring. Please make
sure your system is connected to AC Power before continuing.

The system recovery methods listed below are only available
when your Joybook comes pre-installed with a Windows
operating system.

Should your system become unstable and you wish to restore it
to its original state or make a backup, you can do so following
either of the methods below:

• Method 1: The QDataTrove function of your Joybook. For
details, refer to "Using QDataTrove" below.

• Method 2: The supplied "Operating System Disc" and "Drivers
and Applications" discs (available depending on your
purchased model). For details, refer to "Recovering your

system using the supplied discs" on page 45.

Using QDataTrove

Launching QDataTrove:

1. Start your Joybook.

2. During the startup process, press the <F10> key when you

see "Press F10 key to enter QDataTrove" on the upper left part
of the screen.

3. The following options will then display on the screen. Click

Backup or Restore to proceed according to your need.

Backing up your files:

• Make sure your system is connected to AC Power before
performing the task.

• If you already have a previous backup file on the D: drive, then
it will be replaced.

• The backup files will occupy a large amount of disk space,
over 10GB, so make sure your D: drive has sufficient free
space available. You can click the D: drive under "Computer"
in Windows Vista, and then the total size and available free
space will appear in the Details pane at the bottom of the
folder window.

a. Make sure your D: drive has sufficient free space. For

details, refer to the note above.

b. To back up your complete system drive files, click

System Drive Backup/Primary Drive Backup under the
Backup tab to proceed.

Recovering your system 43

c. Follow the on-screen instructions to complete the task.

The backup creates a "BenQ user" folder on the D: drive, which
can be burnt to disk and archived independently of QDataTrove.

Recovering your backup files:

a. To browse your existing backup files or folders, and

recover them to the drive you selected, click Recover
Backup Files under the Restore tab to proceed.

b. Follow the on-screen instructions to complete the task.

Restoring your backup image:

a. To restore your Joybook from your previous backup

image, click Full System Restore - Backup Image under
the Restore tab.

b. Follow the on-screen instructions to complete the task.

Restoring your Joybook to factory default settings:

This process will ERASE ALL data on your system drive C: and
restore the system to default factory configuration.

If this option is selected, all programs you installed or data you
saved on the C: drive will be erased. However, data on the D:
drive will not be affected.

a. To restore your Joybook to its factory settings, click

Full System Restore - Factory default settings under
the Restore tab.

b. Follow the on-screen instructions to complete the task.

Recovering your system44

Recovering your system using the supplied discs

To recover your system using the "Operating System Disc" and
"Drivers and Applications" discs, follow the procedure and
instructions below carefully.

Step 1: Reinstalling a clean copy of Windows Vista

• All programs you installed or data you saved on the C: drive
will be erased. However, data on the D: drive will not be
affected.

• Recovering your system by using Method 2 (the supplied
"Operating System Disc" and "Drivers and Applications"
discs) will cause the QDataTrove function to become
unavailable. You will also need to install the device drivers
manually from the "Drivers and Applications" discs.

• Do not remove discs when the recovery is in progress until
prompted to do so.

• Before using the "Operating System Disc" and "Drivers and
Applications" discs, make sure the system is not in
hibernation mode or turned off. Also make sure the lid of your
Joybook is not closed during the recovery.

The availability of the supplied discs may vary depending on
your purchased model.

1. Turn on your Joybook.

2. Press the <F9> key when the BenQ logo appears on the

screen during system startup. A Boot Menu screen appears.

3. Insert the supplied "Operating System Disc" into your optical

drive.

4. Use <> or <> to select CD-ROM/DVD-ROM, and then

press Enter.

5. Press any key when you are prompted with Press any key to
boot from CD or DVD. Please wait while Windows is loading
files.

6. The Install Windows screen appears. Select the operating
system you want to install, and then click Next.

7. On the Where do you want to install Windows? screen, select
the primary disk partition, and then click Format.

This will remove all programs and data on the C: drive where
Windows Vista is currently installed. However, other drives will
not be affected.

8. Click Next. Your Joybook will restart a few times during the
installation. Please wait while the installation is in progress.

9. Follow the remaining on-screen instructions to complete the
installation and setup.

10.When you finish reinstalling the operating system, be sure to
remove the "Operating System Disc" from your optical drive.

11.Restart your Joybook.

12.To make the Joybook operate properly, it requires the
reinstallation of the drivers and software programs located on
the "Drivers and Applications" discs, which would have been
erased from your Joybook when the C: drive was formatted.

Recovering your system 45

Step 2: Reinstalling drivers and applications

1. Insert the "Drivers and Applications" disc into your optical
drive.
The main screen will be displayed automatically.

If the AutoPlay feature of your optical drive is disabled in your
system, the screen will not pop up automatically. Go to the
"QAutoCD" folder, and then double-click the "QAutoCD.exe" file
to launch the program manually.

2. You can perform the following tasks on the main page.

• To install drivers, click Install Joybook Driver.

• To install applications, click Install Joybook
Application.

• To view the drivers and applications that are available
for your model, click View Software List.

• When installing drivers, it is recommended to go to "Chipset"
and "Audio" to perform the driver installation first.

• To make your system work properly, install all drivers and
applications that are available for your model.

3. Follow the remaining on-screen instructions to complete the

installation.

Protecting your Joybook from viruses and other security threats

Your Joybook comes with an Anti-Virus CD, so please be sure to
install the anti-virus software from the disc supplied. Doing so
helps you to avoid unexpected destruction of your precious data
in the Joybook and keeps your privacy against any unauthorized
access from other computers.

The anti-virus software protects your computer against Internet
threats, such as viruses, Spyware, hackers, and spam. In
addition, you can secure your personal information, block
unwanted web sites, and check e-mail for viruses.

However, we would still recommend that you back up your data
regularly on CDs, DVDs or other storage media, since the anti­virus software may not be able to intercept all existing and new
viruses, which may lead to destruction of all or some of your
data in the the Joybook.

For more information about how to use the anti-virus software
installed, please refer to the online help that comes with the
software.

Recovering your system46

Connecting to external display devices

Connecting to a VGA display device

You can output your Joybook's video signal to an external display device, such as a projector or monitor. Once the VGA cable is
connected properly, simultaneous display will be available on your Joybook and the external display device automatically.

Pressing the <Fn> + <F3> hotkey combination allows you to switch between the Joybook's own screen and the external display
device, or use simultaneous display.

Monitor

Projector

Connecting to external display devices 47

S-Video output

The S-Video Out socket on your Joybook allows you to output display signals to S-Video capable devices, such as a television set or
VCR for viewing or recording.

When you output display signals on your Joybook to an S-Video capable device, such as a TV set, the resolution on your Joybook will
be adjusted automatically. To restore the resolution to 1280 x 800 after disconnecting the S-Video cable, press the <Fn> + <F3> hotkey
combination again.

TV

VCR

The S-Video Out socket on your Joybook supports video signals only. For the audio function, you will need a separate audio cable.

1. Plug one end of the audio cable to your Joybook earphone output socket.

2. Plug the other end to the audio input socket of the external device.

To select an appropriate audio stream, refer to "Earphone/SPDIF audio output socket" on page 10.

Connecting to external display devices48

Adjusting video standards manually

The graphics card determines the signal format from the
Regional and Language Options selections in Control Panel.
However, when you travel to another country/region, you might
need to re-adjust TV format selections manually. To do so,
follow the steps below.

1. Right-click on the desktop, and then select Graphics
Properties.

2. Click Display Settings, and then select the Te l e v i s i o n tab.

Connecting to external display devices 49

3. Select the appropriate standard from the drop-down list next
to Video Standard.

The required settings of Video Standard may vary by country/
region. For details about which standard is used in your
country/region, check with your local authorities.

Connecting to external display devices50

Installing additional memory

You can replace the existing memory module with a higher­capacity one. Before you upgrade or replace memory, please
check on the BenQ web site to determine the module which can
be used, or contact BenQ distributor or customer service center.
It is recommended that you take your Joybook to the BenQ
distributor or customer service center for the upgrade or
memory replacement.

For details about the limit of maximum memory, refer to the
product information from http://BenQ.com. Click Products,
Computing, Joybook, and then select your purchased model.
Click Specifications to find out the limit of maximum memory.

To find out the types of BenQ certified memory modules for
your Joybook, try the steps below:

1. Connect to BenQ Online Service and Support
(http://Support.BenQ.com).

2. Select your country/region.

3. Try to check Product Support or Technical Support
information to find out the types of BenQ certified memory
modules.

Or, check Service Center information to contact your local
service center for help.

If you install an uncertified memory module, your system may
not work properly.

1. Shut down your Joybook completely. Disconnect the power
adapter and turn over your Joybook.

Memory
cover

Battery

2. Slide the battery retainer A to the unlock

position.

Battery retainer A

Installing additional memory 51

3. Slide the battery retainer B to the unlock position (1) and,
while still holding the retainer, pull the battery away from its
compartment (2).

Battery retainer B

4. The memory cover is secured with 3 screws. Use a
screwdriver to remove these screws.

5. Open the cover.

• Ground yourself to your Joybook with professional grounding
equipment like an anti-static wristband, or touch the metal
surface on the inside of your Joybook to discharge any static
electricity.

• Handle the memory module by its edge and avoid touching the
contacts.

6. Align the memory module with the slot, and then insert it.

When inserting, pay attention to the direction of the memory
module.

The screw labels indicate screws' position to help you locate
them easily. Only remove these 3 screws on the memory cover.

Installing additional memory52

7. Gently push the free edge downwards until the module locks
into place.

9. Use a screwdriver to secure it with the screws.

If the memory module is not installed properly, your Joybook
may not boot properly.

8. Replace the cover.

10.Place the battery on its original position (1) and then slide
the battery retainer A to the to the lock

position (2).

Connect the power adapter. When you start the Joybook, it
will automatically test and configure the new memory.

Battery
retainer A

It is recommended that you go into BIOS to load setup defaults
after installing additional memory. For details, refer to "Using

BIOS setup" on page 39.

Installing additional memory 53

FAQ and troubleshooting

The chapter describes situations that you may encounter during
use of the Joybook, along with basic troubleshooting steps. If
you are not able to resolve the issue, contact a nearest BenQ
service center for assistance immediately.

General

What is Joybook? What are the differences between the Joybook
and traditional notebooks?

BenQ has combined entertainment and stylish design with
traditional notebook's functions into your Joybook. For
example, enhanced 3D processing power for gaming and movie
viewing. With your Joybook, you will be able to enjoy the more
exciting audio and visual experience than ever!

What is a Wireless LAN (WLAN)?

A WLAN is a type of Local Area Network (LAN) that uses high
frequency radio waves rather than wires to communicate and
transmit data among nodes. It is a flexible data communication
system implemented as an extension to, or as an alternative for,
a wired LAN within a building or campus.

What is IEEE 802.11a/b/g?

IEEE 802.11a/b/g is a technical specification issued by the
Institute of Electrical and Electronics Engineers (IEEE) that
defines the operation of 5 GHz/54Mbps, 2.4 GHz, 11 Mbps/
54Mbps, Direct Sequence Spread Spectrum Wireless Local Area
Networks (WLANs).

Battery and power

How long should I charge the battery for the first time?

The length of the charging time may vary. When the amber light
of the battery indicator goes off, it means that the battery is fully
charged.

My Joybook won't start up with the battery inserted. What
should I do?

• Make sure the battery is properly inserted.

• Make sure the battery is fully charged. If this does not work,
consult your BenQ dealer.

What should I do with the battery if I will not use my Joybook
for a long time?

Recharge the battery or discharge it to about 40% full, and then

store it in a dry place at about 15°C to 25°C. Extremely high or

low temperature will shorten the battery life.

FAQ and troubleshooting54

The battery indicator on my Joybook suggests that the battery is
fully charged. However, when I check it from the Power
Manager in Windows, the battery level is only about 95%-99%.
Why?

It is the result of the battery protection design of your Joybook.
When the battery indicator on your Joybook goes off, it means
that the battery has reached a saturated voltage: 95%~99%. At
this moment, the voltage difference detected by your Joybook is
very small, so it will reduce the charging current to prevent
overcharging the battery with excess current or voltage, which
will damage the battery. Moreover, in order to protect the
battery from exposing to high voltage and current for a long
time during charging, the battery has been equipped with a
protection circuit that will charge the battery at low current in
the final phase.

How come my notebook is not fully charged even after a full
night charge?

Make sure the Joybook is receiving power. Is the power cord
plugged in correctly? If the battery is installed in the Joybook
and it is properly connected to an AC outlet, check if the battery
meter icon is showing a charge sign. If this does not fix the
problem, then the battery, the power source in your Joybook, or
the AC power cord may be defective. Consult your BenQ dealer
for help and maintenance.

What should I do if the battery gets hot in my Joybook?

Take the battery out and let it cool down for a while. If the
problem persists when the battery is inserted again into your
Joybook later, the battery could be defective and it may need to
be replaced. Consult your BenQ dealer for help and
maintenance.

I have pressed the Power button, but my Joybook cannot start
up.

Check the power button indicator.

• If it is not lit up, your Joybook is not being supplied by power,
either from an external power source via the power adapter or
from the battery pack. Make sure you have connected the
power adapter correctly to the power socket of your Joybook
and a working electrical outlet, so the battery can start
charging.

• If the power indicator is lit up in blue, the Joybook is
being supplied normally with power, meaning that the
problem lies elsewhere.

• If you have added any hardware, such as a memory
module, check if it has been installed correctly.

• It is possible that certain operating system files are
damaged or missing. If so, you may need to back up all
your data first, and then recover your system. Refer to

"Recovering your system" on page 43 for details.

FAQ and troubleshooting 55

Why does the battery on my Joybook seem to last shorter and
shorter?

It is normal for Lithium-ion (Li-ion) batteries to decline in
capacity over time.

Connection

4. Select the appropriate mode according to the settings of your
LAN service from the Va l u e drop-down menu on the right,
and then click OK.

• If the situation persists, press to disable the wireless

LAN to reduce interference of different network connection
modes.

My modem does not connect at 56K speed. Why?

Several factors can affect connection speed, such as line noise,
the number of people connecting/connected to your ISP, and
the age and condition of the telephone lines. A 56K modem does
not guarantee all connections at 56K.

I cannot connect to the Internet with the built-in network
interface on my Joybook. Why?

Check if the network has a fixed MAC address. Contact your
network administrator for further solutions.

When connecting to a local network, the connection is unstable.
Why?

The instructions below will guide you through the
troubleshooting process.

1. Right-click Computer and select Properties, Device Manager.

2. Double-click Network adapters. When the name of the
network adapter of the Joybook appears, double-click on it.

3. The Properties window will pop up. Click the Advanced tab,
and then click the Speed & Duplex item on the left.

FAQ and troubleshooting56

I have a problem setting up wireless network.

Please follow the instructions below to resolve the problem:

• Have you enabled the wireless LAN function of the Joybook?
Please press the wireless button to enable the wireless

LAN.

• Click the Start button and select Control Panel, Network and
Internet, and Connect to a network. Make sure the connection
status is connected and with appropriate signal strength. If you
do not see the connection status, make sure your wireless
device is set up correctly so your Joybook can receive the
signal.

• Make sure your wireless router or access point is broadcasting
the SSID. Refer to your wireless device's documentation for
enabling this broadcasting feature.

System

How should I resolve the "Low on Disk Space" or "Out of Disk
Space" error messages?

Windows uses disk space for operations, such as caching and
virtual memory. The Joybook may not run reliably if the free
space of the hard disk drops under 100MB or 200 MB. The
following instructions will help you free up the disk space.

1. Click Start, and then click Computer.

2. Right-click the hard disk icon and then select Properties.

3. Observe how much free space is on the hard disk.

4. To free up the space of your hard disk, click Disk Cleanup
and follow the on-screen instructions to proceed.

How do I update the driver?

Please visit BenQ Online Service and Support
(http://Support.BenQ.com) to search for driver updates.

My system is running very slow. How can I improve the
performance?

System resources are the amount of memory and hard disk
space that your Joybook can use, which may degrade over time
and affect the system performance. However, you can still
improve the system performance by using the methods below:

• Close all open programs not being used. Use software

programs that are absolutely necessary. Try running virus
scans and other tools when you are not using your Joybook.

Closing software programs that are not necessary helps your
system performs more efficiently.

• Prevent background software programs from loading. As
software programs load the small icons in the notification area
located in the lower right corner of the desktop, they will be
running in the background and each one consumes valuable
system resources. You can follow the steps below to prevent
application programs from running when Windows launches:

1. Press + R to display the Run dialog box.

2. Type "msconfig" in the Open field. The system configuration

utility will appears.

3. Click the Startup tab, and then uncheck any task that is

unwanted.

4. Click Apply, and then click OK. Restart your Joybook.

• Remove programs from the Startup folder. Removing
programs from the Startup folder also helps prevent programs
from running when Windows starts up. To do so, follow the
steps below:

1. Right-click anywhere in the open area on the desktop and

select New, Folder. Give the folder a name. This folder will be
used later.

2. Right-click the Start button and then select Open. A folder

named Programs will appear in the Start Menu window.

3. Double-click the Programs folder and then the Startup

folder.

4. Right-click any icon in the folder and then select Properties.

The information about the icon will appear.

5. You may decide if the program is necessary to be kept in the

Startup folder. Select unwanted program icons, right-click on
them and select Cut.

FAQ and troubleshooting 57

6. Close the open windows to return to the desktop.

7. Open the folder created in Step 1.

8. Select the Edit and Paste commands in the folder window.
The icons that were cut from the Startup folder are now
placed in the folder.

9. Restart the Joybook. The programs removed from the
Startup folder will no longer run when Windows starts.
However, you can still run them by double-clicking their
icons in the folder created in Step 1.

• Empty the Recycle Bin. You can free up disk space by clearing

files you no longer need from the Recycle Bin. To do so, right­click the Recycle Bin icon on the desktop and select Empty
Recycle Bin.

• Delete temporary files and directories. This will increase the

disk space of your hard disk, and reduce the time Window
takes to access the hard disk. It will also help solve problems
associated with spooling print job.

1. Close all running programs.

2. Click the Start button and select All Programs, Accessories,
System Tools, and then Disk Cleanup.

3. Check the types of files you want to delete (temporary files
are safe to delete).

4. Click OK.

• Use the Scan Disk and Defragment functions. The Scan Disk

function checks a hard disk for errors, while the Disk
Defragment function takes all the scattered bits of program
data and groups them back together in the front of the drive.

1. Click Start, and then click Computer.

2. Right-click the hard disk's icon and select Properties.

3. Click the Tools tab and then the Check Now button.

4. Check all checkboxes in the dialog that follows.

5. Click Start.

6. Restart your Joybook. It may take a long time to complete.
To r un Disk Defragmentation in Windows Vista:

1. Close all running software programs.

2. Right-click the hard disk's icon and select Properties.

3. Click the Tools tab and then the Defragment Now button.

4. Click the Defragment Now button. It may take a long time to
complete.

If Disk Defragmenter start itself over and over, it means that
some hidden background software program is still accessing the
hard disk. Restart your Joybook and try again.

USB devices quit working unexpectedly in Microsoft Windows
Vista. Why?

This is because USB devices, such as cameras, scanners, or
printers, lose its connection and stop working unexpectedly.
Please follow the steps below to resolve the problem.

1. Click Start, and then right-click Computer.

2. Click Properties.

3. Click Device Manager.

4. Double-click the Universal Serial Bus controllers branch to
expand it.

5. Right-click USB Root Hub, and then click Properties.

6. Click Power Management.

7. Deselect Allow the computer to turn off this device to save
power.

8. Repeat Step 5 to Step 7 for each USB Root hub.

9. Click OK, and then close Device Manager.

FAQ and troubleshooting58

Why does the keyboard and/or palm rest get warm?

Typically, the Joybook tends to be warm slightly. The location of
the hard disk is typically underneath the palm rest and as a
result, the palm rest gets warm. The location of the processor is
typically underneath the keyboard. And since the heat rises, the
keyboard may get warm slightly. Since your Joybook has a
thermally controlled fan, when the CPU and/or internal
temperature of the Joybook reaches a certain temperature level,
the fan is turned ON and stays ON until the temperature drops
to a pre-defined level.

The U, I, O, P, J, K, L keys on my Joybook are coming up as
numbers instead of letters. Why?

The number keys are enabled. Press the Num Lk (Number
Lock) key once to disable the number lock function, and the
letters will return to normal.

There is no sound coming from the speakers.

Ver if y t he fo l lo wi ng :

• The speakers may have been muted. Check the volume control
(speaker icon) in the notification area located in the lower
right corner of the desktop to see if the volume has been
muted. If so, please restore the volume.

• The speakers may have been turned off. Use the <Fn> + <F7>
hotkey combination to turn them on.

• The volume may have been set too low. Use the <Fn> + <F9>
hotkey combination to increase the volume.

• An earphone or external speakers may have been connected to
the audio output socket, turning off the Joybook's built-in
speakers automatically.

When a CD or DVD is inserted into the optical drive, there is no
response.

Ver if y t he fo l lo wi ng :

• Your Joybook is turned on, and the CD or DVD discs are
properly inserted in the center of the disc tray in the optical
drive.

• The disc tray is closed.

• The CD or DVD is not bent or badly scratched.

• If you hear the noise from the optical drive when the disc plays,
the optical drive might be deformed, and the Joybook needs to
be repaired. If the disc tray does not open after the eject button
is pressed, insert a pointed object (like an opened paper clip)
into the tray ejection hole next to the ejection button to release
the disc tray.

DVD movies will not play.

The region code of the DVD inserted must match that of the
DVD playback software used. This region code can be set up to
five times. If you have not reached this limit, a prompt that
allows you to change the region code of the software to match
that of the move will appear. Otherwise, you can only play
DVDs with the same region code as the last DVD played
successfully.

FAQ and troubleshooting 59

Why is the hard disk capacity displayed by the OS different from
its nominated capacity?

You may have discovered that the capacity of a 10GB hard disk
becomes 9GB when displayed from the OS, and 20GB becomes
19GB, etc. The bigger the capacity, the bigger the difference. It is
because hard disk manufacturers and OS developers calculate
hard disk capacity in different ways. As a result, the nominated

capacity is different from the exact capacity displayed by the OS.

I hear noise when connecting an earphone to the Joybook.

Verify the following:

• Connect the earphone to other devices, such as a radio to see if
you can still hear that noise. If the noise persists, the earphone
may be out of order.

• If you can hear the noise only when inserting, it is the result of
high instantaneous current. It is a normal phenomenon.

Calculation of hard disk
capacity by hard disk
manufacturers

1GB=1,000MB

1MB=1,000KB

1KB=1,000 bytes

Calculation of hard disk
capacity by OS
developers

1GB=1,024MB

1MB=1,024KB

1KB=1,024 bytes

Example of a 40GB hard disk:

Calculation by hard disk
manufacturers

40GB=40,000MB

=40,000,000KB

=40,000,000,000 bytes

Calculation by OS
developers

40GB=40,960MB

=41,943,040KB

=42,949,672,960 bytes

Exact capacity of a 40GB hard disk displayed in the OS:

40,000,000,000÷1024÷1024÷1024=37.2529 (GB).

Furthermore, when a hard disk is partitioned, the system will
reserve some space on the drive for system files. Therefore, the
total capacity of a hard disk displayed by the OS will never be the
same as its nominated capacity.

FAQ and troubleshooting60

How can I reduce the wearing of the screen hinge when I lift up
the lid of my Joybook?

Please open/close the lid gently and slowly with both hands.
Apply force evenly on both hands to reduce hinge wearing and
prevent deformation or breaking of hinge due to uneven force.

What should I do if a program in Windows freezes?

If your system freezes, press the <Ctrl> + <Alt> + <Delete>
keys simultaneously, click Start Task Manager. Under Windows
Task Man a ge r, click the Applications tab, and then click on the
application that freezes and click End Task.

Why is my Joybook running so hot? Is it normal?

Yes. Because all the hardware is in such cramped quarters, it
tends to get hot. To prevent overheating, do not obstruct the
vent. For example, do not use the Joybook in bed where a
blanket may inadvertently cover the vent and block the airflow.

Why does my Joybook seem to turn off itself after a certain
period of inactivity?

This is the default setting of the Joybook to conserve battery
power. The Joybook is configured to use the power saving
feature. You can go to Control Panel, Mobile PC, and Power
Options to select your preferred power plan.

Should I drain the battery of my Joybook every time before
charging to retain its capacity?

No. Your Joybook comes with an Lithium-ion (Li-ion) battery
pack. This is one of the newest cell types available. It is also the
lightest battery type currently available on a commercial basis
and can provide more power than other main cell types. There
are no known problems of memory effect with this battery type
and it is the easiest battery type to be maintained.

Display

There is nothing visible on the screen.

Check the power button indicator.

• If it is not lit up, no power is being supplied to the Joybook.
Connect the power adapter and restart the Joybook.

• If it is lit up in amber, the Joybook has entered sleep mode in
order to conserve power. Pressing the Power button or any key
should return the Joybook to normal operating mode.

• If it is lit up in blue, the Joybook is being supplied normally
with power. There are two possible causes for the problem.

• The screen's brightness may have been set too low. Use
the <Fn> + <F5> hotkey combination to increase the
brightness.

• The display may have been switched to use an
connected external display device. Use the <Fn> +
<F3> hotkey combination to switch the display back to
the Joybook or to use simultaneous display.

When I connect the Joybook to an external monitor, the display
is abnormal.

The instructions below will guide you through the
troubleshooting process.

• Use the <Fn> + <F3> function key combination to make
external video signal enabled.

• Refer to the user manual that came with the external monitor
to check the settings.

• Connect the cable to the Joybook and reboot the system. If
there is no display on the external monitor after system reboot,
connect the Joybook to a standard VGA monitor, and wait
until you can see things properly on that VGA monitor. Then,
connect the target display to the Joybook again.

• Check if you have connected devices to both the S-Video Out
socket and the 15-pin D-sub video socket on the Joybook. If
yes, disconnect the device connected to the S-Video Out socket
on the Joybook to enable normal signal output from the 15­pin D-sub video socket. In general, if you have connected
devices to both the S-Video Out socket and the 15-pin D-sub
video socket on the Joybook, the S-Video Out socket will be
selected in first priority.

FAQ and troubleshooting 61

How can I judge if my LCD panel is out of order and what
should I do if this happens?

If your Joybook cannot display images at the default resolution,
please visit the BenQ web site to download and update the latest
Joybook display drivers.

Contact your BenQ dealer if you encounter the following
situations:

• The screen flickers when the system starts up normally.

• Fonts displayed on the screen are unclear and strange codes
appear.

• There is no display when the hard disk is running normally.

• Colors on the screen are strange and turn into white.

• Vertical or horizontal lines appear on the screen.

• When playing a media file using Windows Media Player, the
frame speed is abnormal.

• The sound changes while the screen remains the same when
playing games.

Why do I get black and white picture (or horizontal lines) when
I connect my Joybook to the TV?

It is most likely that the signal from the Joybook is not
compatible with your TV. Make sure you select the appropriate
video standard according to your country/region. For details,
refer to "Adjusting video standards manually" on page 49.

FAQ and troubleshooting62

Cleaning and battery maintenance

Battery maintenance

1. Fully charge/discharge battery up to 4 cycles before achieving
full capacity of a new battery.

2. Fully discharge and then fully charge the battery every two to
three weeks for battery conditions.

3. Remove from the device and stored in a cool, dry, clean place
if the battery will not be in use for a month or longer and
recharge the battery after a storage period.

4. Do not short-circuit. A short-circuit may cause severe
damage to the battery.

5. Do not drop, hit or otherwise abuse the battery as this may
result in the exposure of the cell contents, which are
corrosive.

6. Do not expose the battery to moisture or rain.

7. Keep battery away from fire or other sources of extreme heat.
Do not incinerate. Exposure of battery to extreme heat may
result in an explosion.

8. Do not use power adapters other than the one provided with
the Joybook.

9. Do not place the battery within reach of children.

10.Follow the local laws governing the disposal of batteries. As
far as possible, submit used batteries to be recycled.

11.Use of improper batteries, or attempting to disassemble a
battery, may result in explosions. Follow vendor
recommendations in using batteries of the identical or
equivalent type as replacements for worn-out batteries.

Cleaning your Joybook

When cleaning the Joybook, follow these steps:

1. Turn off the Joybook, disconnect the power adapter, and
remove the battery.

2. Use a damp cloth to wipe the outer surface of the Joybook.
Do not apply liquid or spray cleaners directly on the Joybook.

3. Do not use cleaners containing alcohol or acetone. Instead,
use cleaning fluids specially formulated for LCD screens.

Cleaning and battery maintenance 63

Service and support

BenQ Joybook Global Online Service

Welcome to BenQ Joybook Global Online Service
(http://Support.BenQ.com). In order to ensure you an enjoyable
experience with your Joybook, the following supports are
provided so you can get assisted whenever and wherever you
are.

• Support: Here you can select the country/region you are
located in, and visit the specific support web site.

• Knowledge Base: Contains answers to frequently asked
questions about the Joybook as well as additional tips.

• Contact Us: Here you can directly contact BenQ Customer
Service for answers and advice to your questions. You can also
obtain the information about the BenQ service stations in
your country.

Joybook Overseas Regional Warranty (ORW) online registration

Register now to get free product news and latest information
about BenQ! To register, follow the steps below:

1. Refer to the illustration below to locate the 24-digit product
serial number on the bottom side of your Joybook and write
it down.

Serial number

2. Connect to http://service.benq.com/orw/joybook

3. Click Register Now to begin with registration and follow the
instructions on the screen to proceed.

Service and support64

Appendix

General safety information

When setting up or operating your Joybook, please pay special
attention to the following:

1. Keep this manual in a safe place for easy reference when
needed.

2. Make sure you follow all instructions and warnings related to
the system.

3. Place your Joybook on a stable, level surface, and ensure that
the ventilation holes are not obstructed.

4. Do not expose your Joybook to rain or excess humidity, and
keep it away from liquids (such as beverages, faucets, and so
on).

5. Do not expose your Joybook to direct sunlight, and keep it
away from sources of heat (such as radiators, space heaters,
stoves, and so on).

6. Do not expose your Joybook to heavy impacts or strong
vibrations. When closing the Joybook, do not use excessive
force.

7. Don't use your Joybook near a gas leak.

8. Do not store your Joybook in environments where the

temperature is below 0°C or above 50°C, nor use your

Joybook in environments where the temperature is below

5°C or above 35°C. Otherwise system performance will be

adversely affected.

9. Do not use your Joybook near water, for example near a
bathtub, wash bowl, kitchen sink or laundry tub, in a wet
basement or near a swimming pool.

10.Do not place the Joybook in the vicinity of strong magnetic
fields.

11.Use an appropriate electrical outlet, and make sure no heavy
objects are placed on the power adapter or power cord.

12.The power adapter is a high-voltage component. Do not
attempt to repair it yourself. Should it become damaged,
please contact an authorized BenQ distributor or service
center.

13.Make sure the modem port is used only with a regular analog
phone line. Do not connect a digital phone line to the
modem port, as this will cause damage to the modem.

Safety information about the battery

Caution: There is a high risk of explosion if the battery is
incorrectly replaced. Replace only with the same or equivalent
type recommended by the battery equipment manufacturer.
Discard used batteries according to battery manufacturer’s
instructions.

Appendix 65

Safety information about the

Disposal of Waste Electrical

power adapter

• Use only the power adapter supplied with your Joybook. Use of
another type of power adapter will result in malfunction and/
or danger.

• Do not use the adapter in a high moisture environment. Never
touch the adapter when your hands are wet.

• Allow adequate ventilation around the adapter when using it to
operate the device or charge the battery. Do not cover the
power adapter with paper or other objects that will reduce
cooling. Do not use the power adapter while it is inside a
carrying case.

• Connect the adapter to a proper power source. The voltage
requirements are found on the product case and/or packaging.

• Do not use the adapter if the cord becomes damaged.

• Do not attempt to service the adapter. There are no service
parts inside. Replace the unit if it is damaged or exposed to
excess moisture.

Safety information about the modem

Caution

Never connect telephone wiring during a lightning storm. There
may be a remote risk of electric shock from lightning.

and Electronic Equipment by
users in private households in
the European Union.

This symbol on the product or on the packaging
indicates that this can not be disposed of as
household waste. You must dispose of your waste
equipment by handing it over to the applicable take­back scheme for the recycling of electrical and
electronic equipment. For more information about
recycling of this equipment, please contact your city
office, the shop where you purchased the equipment
or your household waste disposal service. The
recycling of materials will help to conserve natural
resources and ensure that it is recycled in a manner
that protects human health and environment.

Appendix66

Declaration of Conformity

For the following equipment:
Type of Equipment:

Notebook PC
Brand name or mark:

BenQ
Model designation(s)/Model no(s):

Joybook S32 Series; DHT300

Company name, address, telephone & fax no.

Name: BenQ Europe B.V.

Ekkersrijt 4130, 5692 DC Son Address:

The Netherlands

TEL/Fax: [phone]

is herewith confirmed to comply with the requirements set out
in the Council Directive on the Approximation of the Laws of
the Member States relating Electromagnetic Compatibility (89/
336/EEC) and Low Voltage Directive (73/23/EEC) and R&TTE
Directive (99/05/EEC).

For the evaluation regarding the electromagnetic compatibility,
the following standards were applied:

EN55022:1998/A1:2000/A2:2003
EN 61000-3-2:2000
EN 61000-3-3:1995/A1:2001
EN 55024:1998/A1:2001/A2:2003
IEC 60950-1 and/or EN60950-1, First Edition
EN 301489-1 V1.4.1:2002
EN 301489-17 V1.2.1:2002
ETSI EN 300328 (V1.5.1:2004-03)
ETSI EN 301893 (V1.2.3:2003-08)

Appendix 67

Safety instructions for Poland, Romania, Slovenia, Bulgaria, Latvia, and Croatia

Polski

1. Należy upewnić się, że zastosowano się do wszystkich

instrukcji i ostrzeżeń dotyczących systemu.

2. Nie należy umieszczać komputera w miejscach

oddziaływania silnych pól magnetycznych.

3. Ostrzeżenie: Nieprawidłowa wymiana baterii może

spowodować jej wybuch. Baterię można wymienić
wyłącznie na baterię tego samego lub zamiennego typu
zalecanego przez producenta urządzenia. Zużyte baterie
należy usuwać zgodnie z instrukcjami producenta.

4. Podłącz zasilacz do prawidłowego źródła zasilania.

Wymagania dotyczące zasilania znajdują się na obudowie
produktu i/lub na opakowaniu.

5. Nie należy używać zasilacza jeśli przewód jest uszkodzony.

6. Nie należy próbować naprawiać urządzenia. Wewnątrz nie

ma części, które można naprawiać. Urządzenie należy
wymienić, jeśli zostanie uszkodzone lub narażone na
oddziaływanie nadmiernej wilgoci.

7. Nigdy nie należy instalować kabli telefonicznych podczas

burzy z wyładowaniami atmosferycznymi.

România

1. Asiguraţi-vă că respectaţi toate instrucţiunile şi
avertismentele privitoare la sistem.

2. Nu plasaţi computerul într-o zonă cu puternice câmpuri
magnetice.

3. Pericol de explozie dacă bateria este incorect înlocuită.
Înlocuiţi numai cu acelaşi tip sau cu un tip echivalent
recomandat de producătorul echipamentului. Aruncaţi
bateriile folosite în conformitate cu instrucţiunile
producătorului.

4. Conectaţi adaptorul la o sursă de tensiune corectă. Cerinţele
privind tensiunea se găsesc pe carcasa produsului şi/sau pe
ambalaj.

5. Nu folosiţi adaptorul dacă se defectează cordonul.

6. Nu încercaţi să depanaţi aparatul. În interior nu există
componente depanabile. Înlocuiţi aparatul dacă acesta se
deteriorează sau este expus la umezeală în exces.

7. Nu instalaţi niciodată cablu telefonic în timpul unei furtuni
cu fulgere.

Appendix68

Slovensko

1. Glede sistema sledite navodilom in opozorilom.

2. Raèunalnika ne postavljajte na mesta z moènim magnetnim
poljem.

3. V primeru nepravilne namestitve akumulatorja obstaja
nevarnost eksplozije. Nadomestite ga le z isto ali ekvivalentno
vrsto, priporoèeno s strani proizvajalca opreme. Rabljen
akumulator odstranite skladno z navodili proizvajalca.

4. Adapter spojite na primeren vir napajanja. Napetostne
zahteve so navedene na ohišju izdelka in/ali njegovi embalaži.

5. V primeru, da je napajalni kabel poškodovan, adapterja ne
uporabljajte.

6. Ne postopajte se popravljanja enote. Znotraj ni nobenih
delov, ki bi jih bilo moè popraviti. Èe je enota poškodovana
ali izpostavljena visoki vlagi, jo nadomestite z novo.

7. Nikoli ne namešèajte telefonske linije med nevihto z
grmenjem.

Български

1. Следвайте всички инструкции и предупреждения
относно системата.

2. Не слагайте ком пютъра на място със силно магнитно
поле.

3. Опасност от експлозия при погрешна смяна на
батерията. Използвайте само същия или еквивалентен
тип батерия, препоръчан от производителя на
оборудването. Изхвърляйте старите батерии съгласно
инструкциите на производителя.

4. Свържете адаптера към подходящ източник на
захранване. Изискванията към напрежението са
посочени на корпуса на продукта и/или опаковката.

5. Не използвайте адаптера, ако кабелът се повреди.

6. Не се опитвайте да поправяте продукта. В него няма

части, които могат да се поправят. Сменете продукта, ако
се повреди или ако бъде изложен на прекомерна влага.

7. Никога не инсталирайте телефонни кабели по време на
гръмотевична буря.

Appendix 69

Latviski

1. Sekojiet visām sistēmai atbilstošajām norādēm un
brīdinājumiem.

2. Nenovietojiet datoru tuvu spēcīgiem magnētiskajiem
laukiem.

3. Nepareizi nomainīts akumulators var uzsprāgt. Mainiet
akumulatoru tikai pret tādu pašu vai līdzvērtīgu ražotāja
ieteiktu akumulatoru. Utilizējiet izlietotos akumulatorus
saskaņā ar ražotāja norādēm.

4. Pievienojiet adapteri atbilstošai strāvas padevei. Strāvas
padeves parametrus Jūs varat atrast uz produkta korpusa un/
vai iepakojuma.

5. Nelietojiet adapteri, ja ir bojāts tā vads.

6. Nemēģiniet labot iekārtu pašrocīgi. Detaļu bojājumu
gadījumā vai arī, ja tā bijusi pakļauta mitruma ietekmei,
griezieties autorizētā servisa centrā.

7. Nekad nelietojiet un neveiciet telefona līnijas pieslēgumu
negaisa laikā.

Hrvatski

1. Pridržavajte se svih uputa i upozorenja u vezi sa sustavom.

2. Ne postavljajte računalo u područje jakih magnetskih polja.

3. Nepravilna zamjena baterije izazvat će opasnost od
eksplozije. Prilikom zamjene, koristite istu ili ekvivalentnu
vrstu baterije koju je preporučio proizvođač. Rabljene
baterije odložite prema uputama proizvođača.

4. Mrežni prilagodnik priključite na odgovarajući izvor
napajanja. Propisani napon naveden je na kućištu proizvoda
i/ili pakiranju.

5. Ne koristite mrežni prilagodnik kojem je oštećen kabel.

6. Ne pokušavajte servisirati uređaj. U uređaju se ne nalaze
dijelovi koje možete popraviti. Uređaj zamijenite u slučaju
oštećenja ili izloženosti prekomjernoj vlazi.

7. Nikada ne instalirajte ožičenje telefona za vrijeme
grmljavine.

Appendix70