Belshaw Type G, TYPE K User Manual
DO NOT THROW AWAY – KEEP IN A SAFE PLACE
OPERATION AND
SERVICE MANUAL
TYPE K DEPOSITORS
Type K Pancake Dispenser
Type K Donut Depositor
Quality bakery equipment for over 80 years
BELSHAW ADAMATIC BAKERY GROUP
814 44TH STREET NW SUITE 103
AUBURN, WA 98001 USA
800.578.2547 USA/Canada (+1)206.322.5474 International
WWW.BELSHAW-ADAMATIC.COM
WWW.BELSHAW.COM
Type K Hushpuppy Depositor
Quality bakery equipment for over 80 years
OPERATION INSTRUCTIONS FOR TYPE K DEPOSITORS
(Video of Type K Pancake Dispenser disassembly and reassembly is available at
http://www.belshaw.com/support)
How to Remove the Plunger
The plunger of the depositor is locked in place with a peg key, held in place
by the operating spring. This key is xed to the release tab, which is located
under the lower end of the spring. By lifting on the release tab, the peg key
can be raised out of the slot in the hopper arch; then by rotating the release
tab and the upper bearing ½ turn, the square key on the upper bearing can
be cleared through the slot in the hopper arch. The plunger assembly may
then be lifted up and removed from the hopper.
How to Disassemble Plunger for Cleaning
Unlock the lock spring from the two legs on the tube, slide tube from the upper piston. Lift inner valve from the tube taking care not to force or drop this
part as it is very delicate and can be easily damaged. After parts have been
cleaned, they should be lightly oiled to prevent sticking. To reassemble,
reverse the disassembly procedure, insert valve into the tube, being certain
it is fully seated. Pass the tube legs through the upper piston and when fully
seated, re-hook the lock spring.
How to Replace the Plunger
Insert the plunger into the hopper, passing the plunger rod through the slot
in the hopper arch. Then start the piston into the cylinder, as the piston
enters the cylinder, the square key on the side of the upper bearing should
be passed through the slot in the hopper arch. To lock in place, press down
on the handle and lift the release tab to allow the upper bearing to be further
depressed until the square key on the upper bearing which has passed
through the hopper arch can be rotated ½ turn. When the upper bearing
has been rotated ½ turn the release tab may be lowered and the peg key on
the release tab will lock into the slot in the hopper arch.
©BELSHAW ADAMATIC BAKERY GROUP • 814 44TH STREET NW SUITE 103
AUBURN, WA 98001 USA • WWW.BELSHAW.COM • WWW.BELSHAW-ADAMATIC.COM
2
How to Use the Dial Adjustment
The machine will deposit 8 different weights of batter by using the dial adjustment. The numbers on the dial, reading the number which is below the
slot in which the selector pin is inserted, will indicate the sizes #1-#8. The
largest deposit of batter is made by setting #8. 1. Push the dial down from
the knob to release it from the peg. 2. Rotate the dial to the desired number.
3. Release the dial, sliding the peg into the slot. DO NOT try to change the
dial setting without rst depressing the spring to release the selector peg.
DO NOT FORCE or use any tool on the dial. It operates freely when the
instructions are followed.
How to Operate the Type K and Batter Boy Depositors
See that the plunger is properly locked in place as per instructions on 1.
“How to replace plunger.”
Operate the machine while it is empty to be certain that it operates 2.
freely.
Set the dial adjustment as per instructions “How to use the dial adjust-3.
ment,” to the size desired.
Fill the hopper with batter. Hold the machine over the mixing bowl, 4.
depress the knob all the way down and release to eject all of the air
out of the valves.
Hold the bottom of the depositor about 1 ½ inches from the griddle, 5.
fryer, or cupcake pan. Depress knob, then release. Keep hopper will
lled to prevent air from getting into the valve mechanism.
If deposits are not the size desired, change the size by setting the dial 6.
adjustment.
The machine should be cleaned as soon as possible after use. Re-7.
move the plunger following the instructions above. Then disassemble
the plunger following the instructions.
Wash and dry all parts of the depositor, oil lightly to prevent sticking, 8.
then reassemble, following the above instructions.
TYPE K PANCAKE DISPENSER • TYPE K DONUT DEPOSITOR
TYPE K HUSHPUPPY DEPOSITOR • OPERATOR’S MANUAL • MN-1536 111010
3
CARE, MAINTENANCE, and CLEANING
INSTRUCTIONS for PLUNGERS and HOPPERS
The plungers and hoppers of your Type K are precision instruments built
from alloy steels and aluminum. They should be handled with care to
insure continued satisfactory performance.
When cleaning aluminum, selection of the right type cleaner is your most
important consideration. Any household dish washing detergent which
is safe for aluminum does a good job of cleaning and does not attack
aluminum. Strong Alkali cleaners, such as lye, soda ash, and tri-sodium
phosphate, will discolor or even corrode aluminum even in weak solutions.
DO NOT HANDLE ROUGHLY or drop on hard surfaces.
DO NOT MIX with other utensils in the sink when washing.
DO NOT ALLOW TO RUST. Always wash parts thoroughly.
DRY COMPLETELY AND THEN LUBRICATE with mineral oil or liquid
shortening before storing or reinstalling in unit.
DO NOT FORCE the machine if it becomes jammed. Disassemble and
remove any obstruction to prevent damage to the plunger.
WASHING PLUNGERS AND HOPPERS BY HAND
Remove plunger from hopper.1.
Use plenty of warm water.2.
Add cleaner approved for aluminum in concentrations recom-3.
mended by manufacturer.
Presoak to loosen stubborn or dried-on deposits.4.
Use a non-scratching plastic scour cloth to remove soil and restore 5.
luster.
Rinse in clear hot water (170-190 deg.)6.
Wipe completely dry.7.
Dip plungers in mineral oil or liquid shortening to prevent rust and 8.
sticking.
©BELSHAW ADAMATIC BAKERY GROUP • 814 44TH STREET NW SUITE 103
AUBURN, WA 98001 USA • WWW.BELSHAW.COM • WWW.BELSHAW-ADAMATIC.COM
4
SPECIAL INSTRUCTIONS FOR THE CARE OF
PANCAKE PLUNGERS:
The pancake plunger must be disassembled and cleaned thor-1.
oughly after every use.
Remove plunger – Using thumb lift up on Spring Cup Lock Assem-2.
bly (K-11A), turn 180 degrees, plunger should release from handle.
Remove Cage Assembly (K-22A) by releasing Lock Spring.3.
Remove Valve Assembly (K-20) from Cage Assembly (K-22A).4.
Clean all parts in warm water with recommended detergents.5.
Dry completely.6.
Reassemble plunger.7.
NOTE: O-Rings are not used on plungers for Type K
Depositors
TYPE K PANCAKE DISPENSER • TYPE K DONUT DEPOSITOR
TYPE K HUSHPUPPY DEPOSITOR • OPERATOR’S MANUAL • MN-1536 111010
5
Loading...