Beko WMB 71043 LMS User manual

Washing Machine

User’s Manual

WMB 71043 LMS

Document Number

2820523770 / 02-01-14.(21:10)

1 Important instructions for safety and environment

This section contains safety instructions that will help protect from risk of perso­nal injury or property damage. Failure to follow these instructions shall void any
warranty.

1.1 General safety

• This product can be used by children at and above 8 years old and by persons
whose physical, sensory or mental capabilities were not fully developed or who
lack experience and knowledge provided that they are supervised or trained on
the safe usage of the product and the risks it brings out. Children must not play
with the product. Cleaning and maintenance works should not be performed by
children unless they are supervised by someone.

• Never place the product on a carpet-covered floor. Otherwise, lack of airflow
beneath the machine will cause electrical parts to overheat. This will cause pro­blems with your product.

• If the product has a failure, it should not be operated unless it is repaired by the
Authorized Service Agent. There is the risk of electric shock!

• This product is designed to resume operating in the event of powering on after
a power interruption. If you wish to cancel the programme, see "Cancelling the
programme" section.

• Connect the product to a grounded outlet protected by a 16 A fuse. Do not ne­glect to have the grounding installation made by a qualified electrician. Our com­pany shall not be liable for any damages that will arise when the product is used
without grounding in accordance with the local regulations.

• The water supply and draining hoses must be securely fastened and remain un­damaged. Otherwise, there is the risk of water leakage.

• Never open the loading door or remove the filter while there is still water in the
drum. Otherwise, risk of flooding and injury from hot water will occur.

• Do not force open the locked loading door. The loading door will be ready to open
just a few minutes after the washing cycle comes to an end. In case of forcing
the loading door to open, the door and the lock mechanism may get damaged.

• Unplug the product when not in use.

• Never wash the product by spreading or pouring water onto it! There is the risk of
electric shock!

• Never touch the plug with wet hands! Never unplug by pulling on the cable,
always pull out by grabbing the plug.

• Use detergents, softeners and supplements suitable for automatic washing ma­chines only.

• Follow the instructions on the textile tags and on the detergent package.

• The product must be unplugged during installation, maintenance, cleaning and
repairing procedures.

• Always have the installation and repairing procedures carried out by the Authorized

Service Agent. Manufacturer shall not be held liable for damages that may arise

from procedures carried out by unauthorized persons.

2 / EN

Washing Machine / User’s Manual

• If the power cable is damaged, it must be replaced by the manufacturer, after
sales service or a similarly qualified person (preferably an electrician) or someone
designated by the importer in order to avoid possible risks.

• Place the product on a rigid, flat and level surface.

• Do not place it on a long-pile rug or similar surfaces.

• Do not place the product on a high platform or near the edge on a cascaded sur­face.

• Do not place the product on the power cable.

• Never use sponge or scrub materials. These will damage the painted, chrome
plated and plastic surfaces.

1.2 Intended use

• This product has been designed for domestic use. It is not suitable for commer­cial use and it must not be used out of its intended use.

• The product must only be used for washing and rinsing of laundry that are mar­ked accordingly.

• The manufacturer waives any responsibility arisen from incorrect usage or trans­portation.

1.3 Children's safety

• Packaging materials are dangerous to children. Keep packaging materials in a
safe place away from reach of the children.

• Electrical products are dangerous for the children. Keep children away from the
product when it is in use. Do not let them to tamper with the product. Use child
lock to prevent children from intervening with the product.

• Do not forget to close the loading door when leaving the room where the product
is located.

• Store all detergents and additives in a safe place away from the reach of the
children by closing the cover of the detergent container or sealing the detergent
package.

While washing the laundry at high temperatures, the loading
door glass becomes hot. Therefore, keep especially the children
away from the loading door of the machine while the washing
operation is in progress.

1.4 Package information

• Packaging materials of the product are manufactured from recyclable materials
in accordance with our National Environment Regulations. Do not dispose of the
packaging materials together with the domestic or other wastes. Take them to the
packaging material collection points designated by the local authorities.

3 / EN

Washing Machine / User’s Manual

1.5 Disposing of the waste product

• This product has been manufactured with high quality parts and materials which
can be reused and are suitable for recycling. Therefore, do not dispose the pro­duct with normal domestic waste at the end of its service life. Take it to a collec­tion point for the recycling of electrical and electronic equipment. Please consult
your local authorities to learn the nearest collection point. Help protect the envi­ronment and natural resources by recycling used products. For children's safety,
cut the power cable and break the locking mechanism of the loading door so that
it will be non-functional before disposing of the product.

1.6 Compliance with WEEE Directive

This product complies with EU WEEE Directive (2012/19/EU). This pro­duct bears a classification symbol for waste electrical and electronic
equipment (WEEE).
This product has been manufactured with high quality parts and mate­rials which can be reused and are suitable for recycling. Do not dispose
of the waste product with normal domestic and other wastes at the
end of its service life. Take it to the collection center for the recycling of
electrical and electronic equipment. Please consult your local authori­ties to learn about these collection centers.

Compliance with RoHS Directive:

The product you have purchased complies with EU RoHS Directive (2011/65/EU).
It does not contain harmful and prohibited materials specified in the Directive.

4 / EN

Washing Machine / User’s Manual

2 Installation

Refer to the nearest Authorised Service Agent for installation
of the product. To make the product ready for use, review
the information in the user manual and make sure that the
electricity, tap water supply and water drainage systems are
appropriate before calling the Authorized Service Agent. If
they are not, call a qualified technician and plumber to have
any necessary arrangements carried out.

Preparation of the location and electrical, tap water and
waste water installations at the place of installation is

C

under customer's responsibility.

warning: Installation and electrical connections of

the product must be carried out by the Authorized

B

Service Agent. Manufacturer shall not be held liable for
damages that may arise from procedures carried out by
unauthorized persons.

warning: Prior to installation, visually check if the product

has any defects on it. If so, do not have it installed.

A

Damaged products cause risks for your safety.
Make sure that the water inlet and discharge hoses

as well as the power cable are not folded, pinched or

C

crushed while pushing the product into its place after
installation or cleaning procedures.

2.1 Appropriate installation location

• Place the machine on a rigid floor. Do not place it on a
long pile rug or similar surfaces.

• Total weight of the washing machine and the dryer -with
full load- when they are placed on top of each other
reaches to approx. 180 kilograms. Place the product
on a solid and flat floor that has sufficient load carrying
capacity!

• Do not place the product on the power cable.

• Do not install the product at places where temperature
may fall below 0ºC.

• Place the product at least 1 cm away from the edges of
other furniture.

2.2 Removing packaging reinforcement

Tilt the machine backwards to remove the packaging
reinforcement. Remove the packaging reinforcement by
pulling the ribbon.

1. Loosen all the bolts with a suitable spanner until they
rotate freely (C).

2. Remove transportation safety bolts by turning them
gently.

3. Attach the plastic covers supplied in the User Manual bag
into the holes on the rear panel. (P)

Keep the transportation safety bolts in a safe place to
reuse when the washing machine needs to be moved

C

again in the future.

Never move the product without the transportation safety
bolts properly fixed in place!

C

2.4 Connecting water supply

The water supply pressure required to run the product is
between 1 to 10 bars (0.1 – 1 MPa). It is necessary to

C

have 10 – 80 liters of water flowing from the fully open
tap in one minute to have your machine run smoothly.
Attach a pressure reducing valve if water pressure is
higher.

If you are going to use the double water-inlet product
as a single (cold) water-inlet unit, you must install the

C

supplied stopper to the hot water valve before operating
the product. (Applies for the products supplied with a
blind stopper group.)

warning: Models with a single water inlet should not be

connected to the hot water tap. In such a case the laundry

A

will get damaged or the product will switch to protection
mode and will not operate.

warning: Do not use old or used water inlet hoses on the

new product. It may cause stains on your laundry.

A

1. Connect the special hoses supplied with the product to
the water inlets on the product. Red hose (left) (max. 90
ºC) is for hot water inlet, blue hose (right) (max. 25 ºC) is
for cold water inlet.

2.3 Removing the transportation locks

warning: Do not remove the transportation locks before

taking out the packaging reinforcement.

A

warning: Remove the transportation safety bolts before

operating the washing machine! Otherwise, the product

A

will be damaged.

5 / EN

warning: Ensure that the cold and hot water connections

are made correctly when installing the product.

A

Otherwise, your laundry will come out hot at the end of
the washing process and wear out.

2. Tighten all hose nuts by hand. Never use a tool when
tightening the nuts.

Washing Machine / User’s Manual

3. Open the taps completely after making the hose
connection to check for water leaks at the connection
points. If any leaks occur, turn off the tap and remove the
nut. Retighten the nut carefully after checking the seal. To
prevent water leakages and damages caused by them,
keep the taps closed when the machine is not in use.

2.5 Connecting to the drain

• The end of the drain hose must be directly connected to
the wastewater drain or to the washbasin.

warning: Your house will be flooded if the hose comes

out of its housing during water discharge. Moreover, there

A

is risk of scalding due to high washing temperatures!
To prevent such situations and to ensure smooth water
intake and discharge of the machine, fix the end of the
discharge hose tightly so that it cannot come out.

• The hose should be attached to a height of at least 40
cm, and 100 cm at most.

• In case the hose is elevated after laying it on the floor
level or close to the ground (less than 40 cm above the
ground), water discharge becomes more difficult and the
laundry may come out excessively wet. Therefore, follow
the heights described in the figure.

• To prevent flowing of dirty water back into the machine
and to allow for easy discharge, do not immerse the hose
end into the dirty water or do not drive it in the drain more
than 15 cm. If it is too long, cut it short.

• The end of the hose should not be bent, it should not be
stepped on and the hose must not be pinched between
the drain and the machine.

• If the length of the hose is too short, use it by adding
an original extension hose. Length of the hose may
not be longer than 3.2 m. To avoid water leak failures,
the connection between the extension hose and the
drain hose of the product must be fitted well with an
appropriate clamp as not to come off and leak.

2.6 Adjusting the feet

warning: In order to ensure that the product operates

more silently and vibration-free, it must stand level and

A

balanced on its feet. Balance the machine by adjusting
the feet. Otherwise, the product may move from its place
and cause crushing and vibration problems.

1. Loosen the lock nuts on the feet by hand.

2. Adjust the feet until the product stands level and
balanced.

3. Tighten all lock nuts again by hand.

warning: Do not use any tools to loosen the lock nuts.

Otherwise, they will get damaged.

A

2.7 Electrical connection

Connect the product to a grounded outlet protected by a 16
A fuse. Our company shall not be liable for any damages
that will arise when the product is used without grounding in
accordance with the local regulations.

• Connection must comply with national regulations.

• Power cable plug must be within easy reach after
installation.

• If the current value of the fuse or breaker in the house is
less than 16 Amps, have a qualified electrician install a
16 Amp fuse.

• The voltage specified in the "Technical specifications"
section must be equal to your mains voltage.

• Do not make connections via extension cables or multi­plugs.

warning: Damaged power cables must be replaced by

the Authorized Service Agents.

B

Transportation of the product

1. Unplug the product before transporting it.

2. Remove water drain and water supply connections.

3. Drain all water that has remained in the product. (SEE

5.5)

4. Install transportation safety bolts in the reverse order of
removal procedure; (SEE 2.3)

Never move the product without the transportation safety
bolts properly fixed in place!

C

warning: Packaging materials are dangerous to children.

Keep packaging materials in a safe place away from

A

reach of the children.

6 / EN

Washing Machine / User’s Manual

3 Preparation

3.1 Sorting the laundry

• Sort laundry according to type of fabric, colour, and
degree of soiling and allowable water temperature.

• Always obey the instructions given on the garment tags.

3.2 Preparing laundry for washing

• Laundry items with metal attachments such as,
underwired bras, belt buckles or metal buttons will
damage the machine. Remove the metal pieces or wash
the clothes by putting them in a laundry bag or pillow
case.

• Take out all substances in the pockets such as coins,
pens and paper clips, and turn pockets inside out and
brush. Such objects may damage the product or cause
noise problem.

• Put small size clothes such as infant's socks and nylon
stockings in a laundry bag or pillow case.

• Place curtains in without compressing them. Remove
curtain attachment items.

• Fasten zippers, sew loose buttons and mend rips and
tears.

• Wash “machine washable” or “hand washable” labeled
products only with an appropriate programme.

• Do not wash colours and whites together. New, dark
coloured cottons release a lot of dye. Wash them
separately.

• Tough stains must be treated properly before washing. If
unsure, check with a dry cleaner.

• Use only dyes/colour changers and limescale removers
suitable for machine wash. Always follow the instructions
on the package.

• Wash trousers and delicate laundry turned inside out.

• Keep laundry items made of Angora wool in the freezer
for a few hours before washing. This will reduce pilling.

• Laundry that are subjected to materials such as flour,
lime dust, milk powder, etc. intensely must be shaken off
before placing into the machine. Such dusts and powders
on the laundry may build up on the inner parts of the
machine in time and can cause damage.

3.3 Things to be done for energy saving

Following information will help you use the product in an
ecological and energy-efficient manner.

• Operate the product in the highest capacity allowed by
the programme you have selected, but do not overload;
see, "Programme and consumption table".

• Always follow the instructions on the detergent
packaging.

• Wash slightly soiled laundry at low temperatures.

• Use faster programmes for small quantities of lightly
soiled laundry.

• Do not use prewash and high temperatures for laundry
that is not heavily soiled or stained.

• If you plan to dry your laundry in a dryer, select the
highest spin speed recommended during washing
process.

• Do not use detergent in excess of the amount
recommended on the detergent package.

3.4 Initial use

Before starting to use the product, make sure that all
preparations are made in accordance with the instructions in
sections “Important safety instructions” and “Installation”.
To prepare the product for washing laundry, perform first
operation in Drum Cleaning programme. If your product
is not equipped with Drum Cleaning programme, perform
the Initial Use procedure in accordance with the methods
described under “5.2 Cleaning the loading door and the
drum” section of the user manual.

Use an anti-limescale suitable for the washing machines.

C

Some water might have remained in the product due to
the quality control processes in the production. It is not

C

harmful for the product.

3.5 Correct load capacity

The maximum load capacity depends on the type of laundry,
the degree of soiling and the washing programme desired.
The machine automatically adjusts the amount of water
according to the weight of the loaded laundry.

warning: Follow the information in the “Programme

and consumption table”. When overloaded, machine's

A

washing performance will drop. Moreover, noise and
vibration problems may occur.

Laundry type Weight (g)

Bathrobe
Napkin
Duvet cover
Bed Sheet
Pillowcase
Tablecloth
Towel
Hand towel
Evening gown
Underclothing
Men’s overalls
Men’s shirt
Men’s pajamas
Blouses

1200
100
700
500
200
250
200
100
200
100
600
200
500
100

3.6 Loading the laundry

1. Open the loading door.

2. Place laundry items loosely into the machine.

3. Push the loading door to close until you hear a locking
sound. Ensure that no items are caught in the door.

7 / EN

Washing Machine / User’s Manual

The loading door is locked while a programme is running.
The door can only be opened a while after the programme

C

comes to an end.

warning: In case of misplacing the laundry, noise and

vibration problems may occur in the machine.

A

3.7 Using detergent and softener

When using detergent, softener, starch, fabric dye, bleach
or limescale remover read the manufacturer's instructions

C

on the package carefully and follow the suggested dosage
values. Use measuring cup if available.

Detergent Drawer

The detergent drawer is composed of three compartments:
– (1) for prewash
– (2) for main wash
– (3) for softener
– (*) in addition, there is siphon piece in the softener
compartment.

3

2

Detergent, softener and other cleaning agents

• Add detergent and softener before starting the washing
programme.

• Never leave the detergent drawer open while the washing
programme is running!

• When using a programme without prewash, do not
put any detergent into the prewash compartment
(compartment nr. "1").

• In a programme with prewash, do not put liquid detergent
into the prewash compartment (compartment nr. "1").

• Do not select a programme with prewash if you are using
a detergent bag or dispensing ball. Place the detergent
bag or the dispensing ball directly among the laundry in
the machine.

• If you are using liquid detergent, do not forget to place
the liquid detergent cup into the main wash compartment
(compartment nr. "2").

Choosing the detergent type

The type of detergent to be used depends on the type and
colour of the fabric.

• Use different detergents for coloured and white laundry.

• Wash your delicate clothes only with special detergents
(liquid detergent, wool shampoo, etc.) used solely for
delicate clothes.

• When washing dark coloured clothes and quilts, it is
recommended to use liquid detergent.

• Wash woolens with special detergent made specifically
for woolens.

warning: Use only detergents manufactured specifically

for washing machines.

A

1

warning: Do not use soap powder.

A

Adjusting detergent amount

The amount of washing detergent to be used depends
on the amount of laundry, the degree of soiling and water
hardness.

• Do not use amounts exceeding the dosage quantities
recommended on the detergent package to avoid
problems of excessive foam, poor rinsing, financial
savings and finally, environmental protection.

• Use lesser detergent for small amounts or lightly soiled
clothes.

Using softeners

Pour the softener into the softener compartment of the
detergent drawer.

• Do not exceed the (>max<) level marking in the softener
compartment.

• If the softener has lost its fluidity, dilute it with water
before putting it in the detergent drawer.

Using liquid detergents
If the product contains a liquid detergent cup:

• Make sure that you have placed the liquid detergent cup
in compartment nr. "2".

• If the liquid detergent has lost its fluidity, dilute it with
water before putting in the detergent cup.

If the product does not contain a liquid detergent cup:

• Do not use liquid detergent for the prewash in a
programme with prewash.

• Liquid detergent stains your clothes when used with
Delayed Start function. If you are going to use the Delayed
Start function, do not use liquid detergent.

Using gel and tablet detergent

Apply the following instructions when using tablet, gel and
similar detergents.

• If the gel detergent thickness is fluidal and your machine
does not contain a special liquid detergent cup, put the
gel detergent into the main wash detergent compartment
during first water intake. If your machine contains a liquid
detergent cup, fill the detergent into this cup before
starting the programme.

• If the gel detergent thickness is not fluidal or in the shape
of capsule liquid tablet, put it directly into the drum before
washing.

• Put tablet detergents into the main wash compartment
(compartment nr. "2") or directly into the drum before
washing.

8 / EN

Washing Machine / User’s Manual