Beko WDIC752300F2 User Manual

Washer-Dryer

User Manual

Document Number=

WDIC752300F2

2820526038_EN/ 15-10-18.(16:19)

Please read these instructions first before using your appliance

Dear Customer, Thank you for choosing a Beko appliance. Please take some time to read this user manual before using your appliance, to ensure you know how to safely operate the controls and functions. Carefully follow all unpacking and installation instructions to ensure the appliance is correctly connected and fitted prior to use. Please write your product model and serial number on the last page of this user manual, and store in a safe location close to the appliance for easy future reference. This user manual may also be applicable for several other models. Differences between models will be listed. If you have any questions or concerns, please call our contact centre or find help and information online at www.beko.co.uk Explanation of symbols used throughout this User Manual

DANGER!

• Warning for electric shock.

DANGER!

• Product weight warning

DANGER!

• Fire risk warning.

CAUTION!

• Warning for hazardous situations with regard to life and property.

PRECAUTION!

• Precautions that need to be taken.

INFORMATION

• Important information or useful hints about usage.

• Read user manual.

• Packaging materials of the product are manufactured from recyclable materials in accordance with regulations.

• Do not dispose of the Packaging materials together with the domestic or other wastes. Take them to the packaging material collection points designated by the local authorities.

• Allergy UK, is the brand of British Allergy Association. Their main endorsement is the ‚Seal of Approval‘. When you see a product with this logo on it, you have the reassurance the product has been scientifically tested to prove it is efficient at reducing/removing allergens from the environment of allergy and asthma sufferers or the products have significantly reduced allergen/chemical content.

“The wool wash cycle of this machine has been approved by The Woolmark Company for the washing of machine washable wool products provided that the products are washed according to the instructions on the garment label and those issued by the manufacturer of this washing machine. M1527 “ “In UK, Eire, Hong Kong and India the Woolmark trade mark is a Certification trade mark.”

This product was manufactured using the latest technology in environmentally friendly conditions.

1 Important instructions for safety and environment

This section contains safety instructions that will help protect from risk of personal injury or property damage. Failure to follow these instructions shall invalidate any warranty.

1.1 General safety

CAUTION!

• This product can be used by children at and above 8 years old and by persons whose physical, sensory or mental capabilities were not fully developed or who lack experience and knowledge provided that they are supervised or trained on the safe usage of the product and the risks it brings out. Children should not play with the device. Cleaning and maintenance works should not be performed by children unless they are supervised by someone. Children under the age of 3 should be kept away unless continuously supervised.

PRECAUTION!

• Never place the product on a carpet-covered floor. Otherwise, lack of airflow beneath the machine will cause electrical parts to overheat. This will cause problems with your product.

• Always have the installation procedures carried out by the competent persons. Manufacturer shall not be held liable for damages that may arise from procedures carried out by unauthorised persons.

• If the product will be used inside a wardrobe/cabinet/module, it is recommended to keep the doors of the wardrobe/cabinet/module open during operation in cases where there are no openings to provide sufficient air circulation.

1.1.1 Electrical safety

• If the product has a failure, it should not be operated unless it is repaired by the Authorised Service Agent. There is the risk of electric shock!

• Never wash the product by spreading or pouring water onto it! There is the risk of electric shock!

INFORMATION

PRECAUTION!

DANGER!

3 / EN

Washer-Dryer / User’s Manual

CAUTION!

• If the power cable is damaged, it must be replaced by the manufacturer, after sales service or a similarly qualified person (preferably an electrician) or someone designated by the importer in order to avoid possible risks.

PRECAUTION!

• Unplug the product when it is not in use.

• Never touch the plug with wet hands! Never unplug by pulling on the cable, always unplug by holding the plug.

• Product should be unplugged during installation, maintenance, cleaning and repair procedures.

• Do not make connections via extension cables or multi-plugs.

INFORMATION

• This product is designed to resume

operating in the event of powering on after a power interruption. If you wish to cancel the programme, see “Cancelling the programme” section.

1.1.2 Product safety

DANGER!

• Never open the loading door or remove the filter while there is still water in the drum. Otherwise, risk of flooding and injury from hot water will occur.

CAUTION!

• The water supply and draining hoses must be securely fastened and remain undamaged. Otherwise, there is the risk of water leakage.

PRECAUTION!

• The product should be used without removing the upper plate.

INFORMATION

• Do not force open the locked loading door. Door can be opened a few minutes after the washing cycle ends. If the machine has not cooled enough at the end of the programme, loading door cannot be opened. Do not force the loading door to open. It must be left to cool itself. The loading door and the lock mechanism may get damaged.

• In the installation location of this product, there must not be a lockable, sliding or hinged door that will restrict the full opening of the loading door.

• Follow the instructions on the textile tags and on the detergent package.

• Use only detergents, softeners and supplements suitable for washing machines.

• Do not install or leave this product in places where it might be exposed to outdoor conditions.

• Controls must not be tampered with.

4 / EN

Washer-Dryer / User’s Manual

1.1.3 Warnings for drying

DANGER!

• Laundry that is previously washed, cleaned, soiled or stained with petrol / gasoline, dry cleaning solvents or other flammable or explosive substances must not be dried in the machine as they give out flammable or explosive steam. It may cause fire risk.

DANGER!

• Do not touch loading door glass with bare hands after drying. There is the risk of getting burnt.

• In order to maintain laundry in a temperature that will prevent them from getting damaged, a cooling step is performed as a final step. You may be exposed to hot steam if you open the door before cooling is complete. There is the risk of scalding.

DANGER!

• Laundry stained with Liquid cooking oil, acetone, alcohol, petrol, kerosene, spot removers, turpentine, waxes and wax removers must be washed in hot water with plenty of detergent before drying. It may cause fire risk.

• Foam rubber (latex foam), shower caps, waterproof textiles, clothes or pillows with rubber support or rubber foam pads must not be dried with drying function. It may cause fire risk.

• If you use washing ball, detergent scale, laundry clothing cages and balls in your machine, they can melt during drying. Do not use these products if drying option will be selected. It may cause fire risk.

• When you use industrial chemicals for cleaning, do not use drying function. It may cause fire risk.

DANGER!

• If the drying programmes are interrupted (as a result of programme cancellation or power failure), laundry in the machine can be hot. Be careful.

CAUTION!

• Do not stop the machine before drying programme is completed. If you have to stop the machine, remove all laundry and lay them in a suitable place to let them cool down.

• Your product is suitable to operate in ambient temperatures between 0°C and +35°C.

5 / EN

Washer-Dryer / User’s Manual

CAUTION!

• Ambient temperatures between 15°C and +25°C are ideal temperatures for your product.

• Do not let pets enter the product. Check inside the product before using.

• Do not overload the machine for drying. Observe the maximum load levels specified for drying.

PRECAUTION!

• Do not dry leather laundry or laundry that contains leather (such as leather jeans label). The colour from Leather parts can run into other textiles.

• In failures that cannot be repaired using information given in safety instructions, turn off the machine, unplug the power cable and call the Authorised Service Agent.

• You can just wash laundry, just dry laundry or wash and dry laundry in your washer-dryer. Machine must not be used only to dry wet loads for a long time. When machine is used only for drying, it must be operated empty without loading laundry in a short wash programme after every 15 operation.

• Check all clothes before loading them into the machine and ensure that they do not have objects such as lighters, coins, metal pieces, needles in the pockets or inside.

• Underwear with metal supports must not be dried in the machine. Metal supports might come off during drying and cause damage in the machine. Place in a bag or pillowcase.

PRECAUTION!

• Do not dry large laundry such as tulle curtain, curtain, bedding, blanket, rug in the machine. Your laundry might get damaged.

INFORMATION

• Do not dry unwashed laundry in the machine.

• Do not use fabric softeners or static preventers in the machine unless recommended by the manufacturer.

• Products such as fabric softeners must be used in accordance with manufacturer’s instructions.

• Do not dry sensitive clothes such as silk, wool, etc. in the machine. Otherwise, wool clothes may get shrunken and other sensitive clothes may get damaged.

• Check symbols on the garment tag before washing and drying.

1.2 Intended use

INFORMATION

• This product has been designed for domestic use. It is not suitable for commercial use and it must not be used out of its intended use.

• The product must only be used for washing, rinsing and drying of textile products that are marked accordingly.

• The manufacturer waives any responsibility arisen from incorrect usage or transportation.

6 / EN

Washer-Dryer / User’s Manual

1.3 Children's safety

CAUTION!

• Children below the age of 3 must be kept away from the machine unless they are continuously supervised.

• Packaging materials are dangerous to children. Keep packaging materials in a safe place away from reach of the children.

• Electrical products are dangerous for the children. Keep children away from the product when it is in use. Do not allow them to play with the product. Use child lock to prevent children from intervening with the product.

• Do not forget to close the loading door when leaving the room where the product is located.

• Store all detergents and additives in a safe place away from the reach of the children by closing the cover of the detergent container or sealing the detergent package.

1.4 Compliance with WEEE Directive and disposing of the waste product

This product does not contain harmful and forbidden materials described in the "Regulation on the Control of the Waste Electrical and Electronic Equipment". It complies with the WEEE Directive.

This product has been manufactured with high quality parts and materials which can be reused and are suitable for recycling. Therefore, do not dispose the product with normal domestic waste at the end of its service life. Take it to a collection point for the recycling of electrical and electronic equipment. Please consult your local authorities to learn the nearest collection point.

Help protect the environment and natural resources by recycling used products. For children’s safety, cut the power cable and break the locking mechanism of the loading door so that it will be non-functional before disposing of the product. Compliance with RoHS Directive: The product you have purchased complies with EU RoHS Directive (2011/65/EU). It does not contain harmful and prohibited materials specified in the Directive.

1.5 Package information

Packaging materials of the product are manufactured from recyclable materials in accordance with our National Environment Regulations. Do not dispose of the packaging with normal domestic waste. Take them to the packaging material collection points designated by the local authorities.

2 Your washer-dryer

2.1 Overview

1- Power cable 2- Top panel 3- Control panel 4- Filter cover 5- Adjustable feet 6- Loading door 7- Detergent drawer 8- Water discharge hose

7 / EN

Washer-Dryer / User’s Manual

2.2 Package contents

Power cable

Water discharge hose

Transit bolts

Mains water inlet hose

User manual

NOTE

8 / EN

Plastic plug group

• Figures in this manual are schematic and may not match the product exactly.

Washer-Dryer / User’s Manual

2.3 Technical specifications

Complying Commission Delegated Regulation (EU) No.96/60/EC/1996

Supplier name or trademark Beko

Model name WDIC752300F2

Washer Dryer Energy efficiency class

Washing Energy efficiency class

(Washing & Drying) Energy Consumption - full load per cycle (kWh) 5,67

Washing Energy Consumption - full load per cycle (kWh) 0,8

Annual (Washing & Drying) Energy Consumption (kWh)

Annual Washing Energy Consumption (kWh)

Water Consumption (Washing & Drying) full load per cycle- (l) 75

Water Consumption (Washing) full load per cycle (l) 45

Annual Water Consumption (Washing & Drying)- (l)

Annual Water Consumption (Washing) (l)

Spin-drying efficiency class (1) B

Maximum spin speed (rpm) 1200

Airborne acoustical noise emissions washing/spinning/drying (dB) 49/72/59

Built-in No

Rated capacity - Washing (kg) 7

Rated capacity - Drying (kg) 5

Height (cm) 82

Width (cm) 60

Depth (cm) 55

Net weight (±4 kg.) 67

Single Water inlet / Double Water inlet

• Available

Electrical input (V/Hz) 230 V / 50Hz

Total current (A) 10

Total power (W) 2200

VDE Main model code 9620

(1)

Scale from A (Highest Efficiency) to G (Lowest Efficiency)

(2)

Energy Consumption based on 200 standard washing cycles - full loads washing (and drying). Actual energy consumption will

depend on how the appliance is used.

(3)

Water consumption based on 200 standard washing cycles - full loads washing (and drying). Actual energy consumption will

depend on how the appliance is used.

Technical specifications may be changed without prior notice to improve the quality of the product.

(1)

(2)

(3)

1134

160

15000

9000

• / -

9 / EN

Washer-Dryer / User’s Manual

3 Installation

To make the product ready for use, review the information in the user manual and make sure that the electricity, tap water supply and water drainage systems are appropriate. If they are not, call a qualified technician and plumber to have any necessary arrangements carried out.

DANGER!

• Make sure that the installation and electrical connections of the product are performed by competent persons. Manufacturer shall not be held liable for damages that may arise from procedures carried out by unauthorised persons.

DANGER!

• Your product is too heavy for one person to carry.

3.1 Appropriate installation location

• Place the product on a solid and level floor. Do not place it onto a carpet with high pile or other similar surfaces.

• Do not place the product close to the edge if the floor contains steps. Do not also place the product on a platform.

• Do not place the product on the power cable.

• Do not install the product in environments where the temperature falls below 0 ºC.(See. Warnings for Drying)

• Leaving a gap at the sides of the machine is suggested to reduce vibration and noise

• In the area where this product is installed, there must not be a lockable, sliding or hinged door that will restrict the full opening of loading door.

• Operate the product in a well ventilated and dust free environment.

• Do not place heat sources such as Hobs, Irons, Ovens, etc. on the washing machine and do not use them on the product

3.2 Removing packaging reinforcement

CAUTION!

• Prior to installation, visually check if the product has any defects on it. If so, do not have it installed. Damaged products cause risks for your safety.

PRECAUTION!

• Preparation of the location and electrical, tap water and waste water installations at the place of installation is under customer’s responsibility.

• Make sure that the water inlet and discharge hoses as well as the power cable are not folded, pinched or crushed while pushing the product into its place after installation or cleaning procedures.

10 / EN

Tilt the machine backwards to remove the packaging reinforcement. Remove the packaging reinforcement attached to the ribbon.

DANGER!

• Your product is heavy. Remove packaging reinforcement as displayed in the figure.

• Be careful not to get your hand caught under the machine during this procedure.

Washer-Dryer / User’s Manual

3.3 Removing the transit bolts

1 2 3

PRECAUTION!

• Do not remove the transit bolts before removing the packaging reinforcement.

• Remove the transit bolts before operating the washing machine! Otherwise, the product will get damaged.

1 Use a tool to loosen all bolts

until they rotate freely.

2 Remove the transit bolts by

turning them slightly.

3 Attach the plastic covers supplied in the user

manual bag into the holes on the rear panel.

INFORMATION

• Keep the transit bolts in a safe place to reuse when the product needs to be moved again in the future.

• Never move the product without the transit bolts properly fixed in place!

3.4 Connecting water supply

1 Connect the special hose supplied with the

product to the water inlet on the product.

CAUTION!

• Ensure that the cold water connection is made correctly when installing the product. Otherwise, your laundry will come out hot at the end of the washing process and wear out.

2 Tighten the hose nuts securely by hand.

Never use a tool when tightening the nuts.

3 Open the taps completely after making the

hose connection to check for water leaks at the connection points. If any leak occurs, turn off the tap and remove the nut. Retighten the nut carefully after checking the seal. In order to prevent the water leaks, keep the taps closed when you do not use the product.

3.5 Connecting to the drain

• Attach the end of the drain hose directly to waste water drain, sink or bathtub.

INFORMATION

• The water supply pressure required to run the product is between 1 to 10 bars (0.1 – 1 MPa). It is necessary to have 10 – 80 liters of water flowing from the fully open tap in one minute to have your product run smoothly. Attach a pressure reducing valve if water pressure is higher.

CAUTION!

• Models with a single water inlet should not be connected to the hot water tap. In such a case the laundry will get damaged or the product will switch to protection mode and will not operate.

• Do not use old or used water inlet hoses on the new product. It may cause stains on your laundry.

11 / EN

CAUTION!

• Your house will be flooded if the hose comes out of its housing during water discharge. Moreover, there is risk of scalding due to high washing temperatures! To prevent such situations and to ensure smooth water intake and discharge of the machine, fix the end of the discharge hose tightly so that it cannot displace.

90 cm

min.40

• Connect the hose to a minimum height of 40 cm and a maximum height of 90 cm.

Washer-Dryer / User’s Manual

90 cm

• If the hose is run along the floor (or at less than 40 cm above it) and raised later on, water drain becomes difficult and laundry may come out extremely wet. Therefore, observe the heights described in the figure.

• To prevent flowing of dirty water back into the machine and to allow for easy discharge, do not immerse the hose end into the dirty water or do not drive it in the drain more than 15 cm. If it is too long, cut it short.

• The end of the hose should not be bent, it should not be stepped on and the hose must not be pinched between the drain and the machine.

• If the length of the hose is too short, add an original extension hose. Length of the hose may not be longer than 3.2 m. To avoid water leak failures, the connection between the extension hose and the drain hose of the product must be fitted well with an appropriate clamp as not to come off and leak.

3.6 Adjusting the feet

CAUTION!

• Adjust feet so that the product will be balanced in the location it will be used.

• Balance the machine by adjusting the feet.

• Check for any play by pressing the product from upper diagonal edges.

• Otherwise, the product may move from its place and cause crushing, noise and vibration problems.

• Do not use any tools to loosen the lock nuts. Otherwise, the lock nuts may get damaged.

a) Loosen the lock nuts on the feet by hand. b) Adjust the feet until the product

stands level and balanced.

c) Tighten all lock nuts again by hand.

Adjusting Rear Feet

• When you turn the knob (visible in the circle) in the direction of the arrow, the machine will be elevated by 0.3 mm. When you turn it in the opposite direction of the arrow, the machine will be lowered by 0.3 mm.

• Do not adjust the rear feet by using chargeable devices. Use a screwdriver instead.

3.7 Electrical connection

Connect the product to a grounded outlet protected by a 13 A fuse. Our company shall not be liable for any damages that will arise when the product is used without grounding in accordance with the local regulations.

• Connection must comply with national regulations.

• The wiring for the electrical outlet circuit must be sufficient to meet the appliance requirements. Use of a Groud Fault Circuit Interrupter (GFCI) is recommended.

• Power cable plug must be within easy reach after installation.

• If the current value of the fuse or breaker in the house is less than 13 Amps, have a qualified electrician install a 13 Amp fuse.

• The voltage specified in the "Technical specifications" section must be equal to your mains voltage.

DANGER!

• Damaged power cables must be replaced by the Authorised Service Agent.

12 / EN

Washer-Dryer / User’s Manual

Important Fitting a different plug

As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals on your plug, proceed as follows: 1 Connect the green - yellow or green

(earth) wire to the terminal in the plug marked ‘E’ or with the symbol f or coloured green and yellow or green.

2 Connect the blue (neutral) wire to the terminal

in the plug marked ‘N’ or coloured black.

3 Connect the brown (live) wire to the terminal

in the plug marked ‘L’ or coloured red. With the alternative plugs a 13A fuse must be fitted either in the plug or adaptor or in the main fuse box. If in doubt contact a qualified electrician.

3.8 Transportation of the product

1 Unplug the product before transporting it. 2 Remove water drain and water

supply connections.

3 Drain all water that has remained

in the product. See 6.5

4 Install the transit bolts in reverse order of

the disassembly procedure. See 3.3

DANGER!

• Your product is too heavy for one person to carry.

• Your product is heavy; two persons must carry it and extra precaution taken on stairs. If your product falls on you, it may cause injuries.

CAUTION!

• Packaging materials are dangerous to children. Keep packaging materials in a safe place away from reach of the children.

INFORMATION

• Never move the product without the transit bolts properly fixed in place!

13 / EN

Washer-Dryer / User’s Manual

4 Preparation

4.1 Sorting the laundry

* Sort laundry according to type of

fabric, colour, and degree of soiling and allowable water temperature.

* Always observe the instructions given

on the garment care labels.

4.2 Preparing laundry for washing

• Laundry items with metal attachments such as, underwired bras, belt buckles or metal buttons will damage the machine. Remove the metal pieces or wash such clothes by putting them in a cotton laundry bag or cotton pillow case. Also these type of clothes can heat too much during drying and damage your other clothes. Do not dry such laundry in the machine.

• Put small size clothes such as infant's socks and nylon stockings in cotton a laundry bag or cotton pillow case.

• Place curtains in without compressing them. Remove curtain attachment items. Do not dry tulle curtains in your machine.

• Fasten zips, sew loose buttons and mend rips and tears.

• Wash “machine washable” or “hand washable” labelled products only with an appropriate programme. Dry these type of clothes by hanging or laying down. Do not dry them in the machine.

• Do not wash colours and whites together. New, dark coloured cottons release a lot of dye. Wash them separately.

• Only use the dyes / colour changers and descaling agents which are appropriate to machine wash. Always follow the instructions on the package.

INFORMATION

• Laundry that is subjected to heavy deposits of materials such as flour, lime dust, milk powder, etc. Must be shaken off before placing into the machine. Such dusts and powders on the laundry may build up on the inner parts of the product in time and can cause damage.

• Keep laundry items made of Angora wool in the freezer for a few hours before washing. This will reduce pilling.

• Wash trousers and delicate laundry turned inside out.

• Tough stains must be treated properly before washing. If unsure, check with a dry cleaner.

• Take out all substances in the pockets such as coins, pens and paper clips, and turn pockets inside out and brush. Such objects may damage the product or cause noise problem.

4.3 Tips for energy saving

Energy efficiency will be improved by using lower temperature programmes and appropriate detergents.

• Operate the product in the highest capacity allowed by the programme you have selected, but do not overload; see, "Programme and consumption table". See, “Programme and consumption table"

• Always follow the instructions on the detergent packaging.

• Wash slightly soiled laundry at low temperatures.

• Use faster programmes for small quantities of lightly soiled laundry.

• Do not use prewash and high temperatures for laundry that is not heavily soiled or stained.

• If you plan to dry your laundry in a dryer, select the highest spin speed recommended during washing process.

• Do not use more detergent than the recommended on the detergent packaging.

14 / EN

Washer-Dryer / User’s Manual

4.4 Initial use

Before starting to use the product make sure that all preparations are made in accordance with the “Important safety and environment instructions” and the instructions in the “Installation” section. To prepare the product for washing laundry, perform first operation in Drum Cleaning programme. If this programme is not available in your machine, apply the method which is described in the section 6.2.

INFORMATION

• Use an anti-limescale product suitable for the washing machines.

• Some water may remain in the product due to the quality control processes in the production. It is not harmful for the product.

4.5 Correct load capacity

The maximum load capacity depends on the type of laundry, the degree of soiling and the desired washing programme. The product automatically adjusts the water amount according to the weight of the laundry put inside it.

CAUTION!

• Follow the information in the “Programme and consumption table”. When overloaded, machine’s washing performance will drop. Moreover, noise and vibration problems may occur. For a successful drying performance, do not dry more laundry than stated.

type

Laundry

Bathrobe 1200 Hand towel 100

Fabric napkin 100

Bed sheet 700 Underclothing 100 Bed sheet 500 Men’s overalls 600 Pillowcase 200 Men’s shirt 200 Tablecloth 250 Men’s pyjamas 500 Towel 200 Blouses 100

(g)

Weight

Laundry

Women‘s night gown

type

200

4.6 Loading the laundry

1. Open the loading door.

2. Put the laundry items into the product in a loose manner.

3. Push the loading door to close until you hear a locking sound. Ensure that no items are caught in the door.

INFORMATION

• The loading door is locked while a

programme is running. The loading door is unlocked a while after the programme comes to an end. If the inside part of the machine is too hot at the end of the programme, loading door will not open until the temperature decreases.

CAUTION!

• If the laundry is misplaced, noise and vibration problems may occur in the machine.

(g)

Weight

15 / EN

Washer-Dryer / User’s Manual

4.7 Using detergent and softener

INFORMATION

• When using detergent, softener, starch, fabric dye, bleach and descaling agents; read the manufacturer’s instructions written on the package and follow the dosages specified. Use a measuring cup if available.

4.7.1 Detergent drawer

The detergent drawer is composed of four compartments:

INFORMATION

• Never leave the detergent drawer open while the washing programme is running!

• When using a programme without prewash, do not put any detergent into the prewash compartment (compartment nr. “I“).

• Do not select a programme with prewash if you are using a detergent bag or dispensing ball. Place the detergent bag or the dispensing ball directly among the laundry in the machine. Remove these if drying

• When machine is in Drying step, do not add any washing chemicals (Liquid detergent, Softener, etc.).

1)Left compartment with number “II” (Main wash compartment for powder detergent or powder bleach/stain remover)

2)Left compartment with number “II ” (Main wash compartment for liquid detergent or liquid stain remover)

3)Middle compartment with number “I” (pre-wash compartment for powder detergent, powder stain remover or liquid bleach - liquid bleach must be added either during the pre-wash or during the first rinsing step of the washing Programme). Liquid bleach must be added manually while the machine takes in water.

4)Right compartment with “ ” symbol (liquid softener compartment) ( ) in addition, there is a siphon piece in the softener compartment.

4.7.2 Main Wash Compartment

Before starting the washing Programme, put powder detergent into the left compartment with number “II”. Powder bleach/stain remover must also be put into this compartment. Put the liquid detergent into the main wash compartment with number “II ” before starting the washing Programme. Liquid stain remover must be put into this compartment. Put the suggested amount of liquid detergent into the left compartment with “II ” symbol and dilute it to the maximum filling level line (max. II ) with warm water. Particularly the concentrated detergents must be diluted with warm water; otherwise, the siphon may get clogged in time. Do not fill the detergent above the maximum filling level line; otherwise the excess amount of detergent will reach the laundry without water and may cause stains on the garments.In this case you will need to refill the compartment. Do not pour the detergent onto the laundry directly since this may cause stains on the garments.

16 / EN

Washer-Dryer / User’s Manual

+ 36 hidden pages