Beijer Electronics T15B User Manual

iXT15BInstallationGuide

1SafetyPrecautions

Both theinstaller and the owner and/oroperator of theoperator panel must read and understand this installation manual.

1.1 General

Read the safety precautions carefully.

•

Check the delivery for transportation damage. If damage is found, notify the

•

supplier as soon as possible.

Do not use the operator panel in an environment with high explosive hazards.

•

The supplier is not responsible for modiﬁed, altered or reconstructed

•

equipment. Use only parts and accessories manufactured according to speciﬁcations of

•

the supplier. Read the installation and operating instructions carefully before installing,

•

using or repairing the operator panel. Never allowﬂuids, metal ﬁlings or wiring debris to enter any openings in the

•

operator panel. Thismay cause ﬁre or electrical shock. Only qualiﬁed personnel may operate the operator panel.

•

Storingthe operator panel where the temperature is lower/higherthan

•

recommended in this manual can cause the LCD display liquid to congeal/become isotopic. The LCD display liquid contains a powerful irritant. In case of skin contact,

•

wash immediately with plenty of water. In case of eye contact, hold the eye open, ﬂush with plenty of water and get medical attention. Theﬁguresinthismanualservesanillustrativepurpose. Becauseofthemany

•

variables associated with any particular installation, the supplier cannot assume responsibility for actual use based on the ﬁgures. The supplier neither guarantees that the operator panel is suitable for your

•

particular application, nor assumes responsibility for your product design, installation or operation. It is recommended to turn on and shut down the operator panel at least once

•

before installing any components/cards or before connecting the operator panel to external devices, like for example serial devices.

1.2 ULandcULInstallation

This equipment is suitable for use in Class 2 non-hazardous locations only.

•

[Combinations of equipment in your system are subject to investigation by the local authority having jurisdiction at the time of installation]. All devices have to be supplied by a Class 2 power supply.

•

Warning:

Donotdisconnectequipmentunlesspowerhasbeen removed or theareaisknowntobenon-hazardous

ForCanada also AVERTISSEMENT– AVANTDE DECONNECTER

•

L’EQUIPEMENT,COUPERLECOURANTOUS’ASSURER QUE L‘EMPLACEMENT EST DESIGNE NON DANGEREUX.

Warning:

OnlyULandcULapprovedexpansionunitsareallowedtobe connectedtotheportdesignated“EXPANSION”. Atthemoment therearenosuchunitsevaluatedorallowed.

Warning:

Donotreplaceexpansionunitunlesspowerhasbeenswitchedoff ortheareaisknowntobenon-hazardous.

This product contains a battery; this must only be changed in an area known

•

to be non-hazardous. Replace the battery with a BR 2032 battery. Use of another type of battery

•

may present a risk of ﬁre or explosion.

Warning:

Batterymayexplodeifmistreated. Donotrecharge,disassemble ordisposeofinﬁre.

Foruse on a ﬂat surface of a type 4X enclosure indoor use only.

•

Use75degreeconductorsonly

•

Use copperconductors only

•

Tomake wiring connections to the power supply connector, follow the table

•

with cable and torque speciﬁcations below:

TerminalBlockNo. WireSizeAWG TQLb.In.

X1/X100Phoenixconnectors X1/X100Anytekconnectors

These devices are Class 2 supplied programmable controllers (industrial PCs)

•

AWG 30–12 AWG24–12 3.5

5–7

for the use in industrial control equipment and are intended to be (front) panel mounted (Type 1 and 4x for indoor use only).

1.3 DuringInstallation

The operator panel is designed for stationary installation on a plane surface,

•

where the following conditionsarefulﬁlled:

– no high explosive risks – no strong magnetic ﬁelds – no direct sunlight – no large, sudden temperature changes

Install the product according to the accompanying installation instructions.

•

Groundthe product according to the accompanying installation instructions.

•

Only qualiﬁed personnel may install the operator panel.

•

Separate the high voltage, signal and supply cables.

•

Make sure that the voltage and polarity of the power source is correct before

•

connecting the product to the power outlet. Peripheralequipmentmustbeappropriatefor the application and location.

•

1.4 DuringUse

Keep the operator panel clean.

•

Emergency stop and other safety functions may not be controlled from the

•

operator panel. Do not use too much force or sharp objects when touching the keys,

•

touchscreen etc.

1.5 Serviceand Maintenance

Only qualiﬁed personnel should carry out repairs.

•

The agreed warranty applies.

•

Before carrying out any cleaning or maintenance operations, disconnect the

•

equipment from the electrical supply. Clean the display and surrounding front cover with a soft cloth and mild

•

detergent. Replacing the battery incorrectly may result in explosion. Only use batteries

•

recommended by the supplier. During the warranty period, the battery needs to be replaced by an authorized Beijer Electronics service center.

1.6 Dismantlingand Scrapping

The operator panel or parts thereof shall be recycled according to local

•

regulations. The following components contain substances that might be hazardous

•

to health and the environment: lithium battery,electrolytic capacitor and display.

1.7 AppearanceofAirinTouchScreen

Thelayerstructureofthetouchscreencontainsairandinrarecases

•

appearance of bubbles can arise. This is purely cosmetic and does not affect any functionality of the panel. The appearance can occur under certain environmental conditions such as temperature, humidity, and atmospheric pressure.

2Installation

2.1 SpaceRequirements

Maximum installation plate thickness: 8 mm

•

Space requirementsinmillimeters when installing the operator panel:

•

286

100 100

410

Note:

Thedimensionsonthedrawingarenotproportional.

1005050

2.2 Installation Process

The following is needed:

ATorxTX7screwdriver

•

Unpackandcheck the delivery. If damage is found, notify the supplier.

Note:

Placetheoperatorpanelonastablesurface during installation. Droppingthepanelorlettingitfallmaycausedamage.

Use the cut out dimensions that are included on the outline drawing, found in section Operator PanelDrawings andin the Technical Data table, to cut a correct opening in the cabinet. A separate cut out drawing is available for download from the Beijer Electronics web site.

Secure the operator panel in position by screwing the M4 Torxscrew, allowing the built-in bracket to tighten against the panel:

M4 x 20.7

0.4 Nm

Connect the cables in the speciﬁed order, according to the drawing and steps below.

Caution:

Ensurethattheoperatorpanelandthecontroller system havethesame

•

electricalgrounding(referencevoltagelevel),otherwiseerrorsin communicationmayoccur. Theoperatorpanelmustbebroughttoambienttemperaturebeforeit

•

isstartedup. Ifcondensationforms, ensure thattheoperatorpanelis drybeforeconnectingittothepoweroutlet. Ensurethatthevoltageandpolarity of the power sourceiscorrect.

•

Useonlyshieldedcommunicationcables.

•

Separatehighvoltagecables from signalandsupplycables.

•

RS232/ RS422/ RS485

24V DC

Ethernet

– Connect cable A. – Connect cable B, using an M5 screw and a grounding conductor (as

short as possible) with a cross-section of minimum 2.5 mm

– Connect cable C. – Connect cable D. The recommended cross-section of the cable is

Carefully removethelaminatedﬁlmovertheoperatorpaneldisplay,to avoid

1.5 mm

Power

Controller

24V DC

static electricity that could damage the panel.

2.2.1 ConnectionstotheController

Forinformationaboutthecablesto be used when connecting the operator panel to the controller,pleaserefertothe help ﬁle for the driver in question.

2.2.2 OtherConnectionsandPeripherals

Cables, peripheral equipment and accessories must be suitable for the application and its environment. For furtherdetailsorrecommendations,pleaserefertothe supplier.

3TechnicalData

Parameter iXT15B

Frontpanel,W×H×D Cutoutdimensions,W×H Mountingdepth 76mm(176mmincludingclearance) Standalonemounting

Frontpanelseal Rearpanel seal Touchscreenmaterial Polyesteronglass,resistive.

Touchscreenoperations 1millionﬁngertouchoperations Reversesidematerial Powder-coatedaluminum Framematerial Powder-coated aluminum Weight 3.85kg Serialportfor

COM1RS232and COM2RS422/RS485

Serialportfor COM3RS232and COM4RS422/RS485

Ethernet 1×10/100/1000Mbit/s and 1 × 10/100

USB 3×USBHost2.0,maxoutputcurrent500mA Processor Externalstoragemedia 1×SDcard(optional). Only compatible

MemoryRAM 1GB LED Realtimeclock Yes(onchip) Battery

Powerconsumptionat ratedvoltage

Fuse Powersupply

Display TFT-LCDwithLED backlight. 1280×800 pix-

Activeareaofdisplay, W×H

Operatingtemperature -10°C–+50°C Storagetemperature -20°C–+70°C Relativehumidity 5%–85%non-condensed Approvalsand

certiﬁcations

(1)

SeesectionChemicalResistance for moreinformation.

410×286×83mm 394×270mm

VESA75×75 Note: Maximumscrewlength for VESA mountingis4mm. Usageoflongerscrews mayleadtodamage.

IP65 IP20

(1)

Overlay: Autoﬂex EBA 180L

9-pinD-subcontactwithRS232RTS/CTS, chassis-mountedfemalewithstandard lockingscrews4-40UNC

Mbit/s. Shielded RJ45

Intel®Atom

withthestandardSDformat withupto2GB storagecapacity.

1×multi-color

LithiumbatterytypeBR2032(or CR 2032), exchangeable

24W

3.15ASlow +24VDC(18-32VDC)

CE:Thepowersupplymustconformwiththe requirementsaccordingtoIEC60950and IEC61558-2-4. ULandcUL:Thepowersupplymustconform withtherequirementsforclassIIpower supplies.

els,262kcolors

331.2×207.0mm

Informationisavailableonthewebsite

www.beijerelectronics.com

4 ChemicalResistance

4.1 MetalCasing

The frame and casing material is powder-coated aluminum. This powderpaint withstands exposure to the following chemicals without visible change:

Aceticacid10% Phosphoric a cid 4% Citricacid10% Phosphoricacid10% Diesel Distilledwater Sodiumchloride2% Edibleoil Sodiumchloride20% Fueloil Sulphuricacid20% Hydrogenperoxide3%

The powder paint shows limited resistance to the following chemicals at room temperature:

Butanol Nitricacid3% Hydrochloricacid 5% Nitricacid10% Isopropylalcohol Phosphoricacid43% Na-hypochlorite10%

Note:

Ifexposuretoanyoftheabovechemicalsisdemanded,itisrecommendedto ﬁrsttestthechemicalinahiddenspot of themetalcasing.

Seawater

Tap water

Turpentine

Autoﬂex EBA 180L withstands DIN 42 115 Part2 exposureof up to 1 hour duration to glacial acetic acid without visible change.

Autoﬂex EBA 180L is not resistant to high pressure steam at over 100 °C or the following chemicals:

Concentratedmineralacids Benzylalcohol Concentratedcausticsolution Methylenechloride

4.2.2 Touch ScreenSurface

The touch screen surface on the operator panel withstands exposure to the following solvents without visible change:

Solvents

Time

Acetone 10minutes Isopropanol

10minutes

Toluene 5hours

4.2.3 AutoﬂexEBA180L

It is recommended to use the Autoﬂex EBA 180Ltouch display protection ﬁlm, that can be ordered from Beijer Electronics.

SolventResistance

Autoﬂex EBA180L withstands exposuretothesamechemicalsasAutotexF157 or F207 according to section Autoﬂex EBA 180L.

OutdoorUse

In common with all polyester based ﬁlms, Autoﬂex EBA 180L is not suitableforuse in conditions of long-term exposure to direct sunlight.

5 OperatorPanelDrawings

5.1 Connectors

Note:

Inordertoutilizetwocommunicationportson the same physicalport,the Y-splitcableCAB109mustbeused. DrawingforexternalcableCAB109(drawing#Z7100-029E)isavailableonthe website: www.beijerelectronics.com

5.3 iXT15BOutline

286

max. 8 mm

99392410

268

The information in this document is subject to change without notice and is providedas available at the time of printing. Beijer ElectronicsAB,including all its group companies, reserves the right to change any information without updating this publication. Beijer Electronics AB, including all its group companies, assumes no responsibility for any errors that may appear in this document. Readtheentireinstallationmanual prior to installing and using this equipment. Onlyqualiﬁed personnel may install, operate or repair this equipment. BeijerElectronicsAB,includingallitsgroupcompanies,are not responsible for modiﬁed, altered or renovated equipment. Because the equipment has a wide range of applications, users must acquire the appropriate knowledge to use the equipment properly in their speciﬁc applications. Persons responsible for the application and the equipment must themselves ensure that each application is in compliance with all relevant requirements, standards and legislation in respect to conﬁguration and safety. Only parts and accessories manufactured according to speciﬁcations set by Beijer Electronics AB, including all its group companies, may be used. BEIJER ELECTRONICSAB, INCLUDING ALL ITS GROUP COMPANIES,SHALLNOTBELIABLETOANYONEFORANY DIRECT,INDIRECT, SPECIAL, INCIDENTALORCONSEQUENTIAL DAMAGES RESULTING FROMTHE INSTALLATION, USE OR REPAIR OF THIS EQUIPMENT, WHETHER ARISING IN TORT, CONTRACT, OR OTHERWISE. BUYER'S SOLE REMEDY SHALL BE THE REPAIR, REPLACEMENT, OR REFUND OF PURCHASE PRICE, AND THE CHOICE OF THE APPLICABLE REMEDY SHALL BE AT THE SOLE DISCRETION OF BEIJER ELECTRONICS AB, INCLUDING ALL ITS GROUPCOMPANIES.

The powder paint shows little or no resistance to the following chemicals at room temperature:

Aceticacid,conc. Methyl-ethylketone Toluene Acetone Ammonia5% Ammonia,conc.

Nitricacid30% Trichlorethylene Phenol Xylene Sodiumhydroxide5% 97octaneunleadedpetrol

Ethylacetate Sodium hydroxide30% 98octaneleadedpetrol

4.2 Touch ScreenandOverlay

4.2.1 AutoﬂexEBA180L

Autoﬂex EBA 180L covers the overlay surrounding the touch screen.

SolventResistance

Autoﬂex EBA 180L withstands exposure of more than 24 hours duration under DIN 42 115 Part 2 to the following chemicals without visible change:

Acetonitrile DieselDowney/

Ajax/Vimin

(1)

Lenor Ethanol Potassiumferricyanide

Phosphoricacid(<30%)

solution Alkalicarbonate

(1)

solution Ammonia(<40%) Aceticacid(<50%) Arielpowderin

(1)

solution

(1)

Bleach

Glycerine Potassiumhydroxide

(<30%)

(1)

Glycol Gumption Hydrochloricacid

(1)

PureTurpentine SBP60/95 Sulfuricacid(<10%)

(<36%) Linseedoil Tomatoketchup

(1)

Castoroil Methanol Trichloroaceticacid

(<50%)

Causticsoda

(1)

(<40%) Cuttingoil Parafﬁnoil Windex Cyclohexanol Persilpowderin

Diacetonealcohol Petroleumspirit

(1)

Extremelyfaintglossingofthetexturewasnoted.

Nitricacid(<10%) WhiteSpirit

(1)

solution

(1)

Wisk

(1)

1234567

Pos. Connector Description

Powersupply

+24VDC(18-32VDC) 2 COM 1/2 CommunicationPorts 3LAN(Port2) 4

USB 2×USBHost2.0,maxoutputcurrent500mA

Headphone HeadphoneConnector 6LAN(Port1) 7

COM3/4 CommunicationPorts

1×10/100Base-T(shieldedRJ-45)

1×10/100/1000Base-T(shielded RJ-45)

5.2 CommunicationPorts

Serialport,9-pinfemale Serialport,9-pin female COM1 COM2 COM3 COM4

2RS232RxD 3 RS232TxD 4 5

GND GND GND GND

7RS232RTS 8RS232CTS 9

RS422Tx+

RS485Tx+/Rx+

RS422Rx+

RS422Tx-

RS485Tx-/Rx-

RS422Rx-

RS232RxD RS232TxD

RS422Tx+

RS485Tx+/Rx+

RS422Rx+

RS422Tx-

RS485Tx-/Rx-

RS422RTS+ RS422RTS-

RS422Rx-

Note:

AStepCADﬁleisavailable on thewebsitewww.beijerelectronics.com

Headofﬁce

BeijerElectronicsAB

Box426 20124Malmö,Sweden www.beijerelectronics.com/+4640358600

Beijer Electronics T15B User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual