User’s Manual
Version 1.0 November 2005
MINIFBQ FBQ800
MINIFBQ FBQ800
CAUTION: To reduce the risk of electric shock,
WARNING: To reduce the risk of fire or electric
do not remove the top cover (or the
rear section). No user serviceable
parts inside; refer servicing to
qualified personnel.
shock, do not expose this appliance
to rain and moisture. The apparatus
shall not be exposed to dripping or
splashing and no objects filled with
liquids, such as vases, shall be placed
on the apparatus.
This symbol, wherever it appears,
alerts you to the presence of
uninsulated dangerous voltage inside
the enclosure—voltage that may be
sufficient to constitute a risk of shock.
This symbol, wherever it appears,
alerts you to important operating and
maintenance instructions in the
accompanying literature. Please
read the manual.
DET AILED SAFETY INSTRUCTIONS:
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8) Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug
has two blades with one wider than the other. A grounding type plug has two blades and a
third grounding prong. The wide blade or the third prong are provided for your safety. If the
provided plug does not fit into your outlet, consult an electrician for replacement of the
obsolete outlet.
10) Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
11) Only use attachments/accessories specified by the manufacturer.
12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold
with the apparatus. When a cart is used, use caution when moving the cart/apparatus
combination to avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or when unused for long periods of time.
14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus
has been damaged in any way, such as power supply cord or plug is damaged, liquid has
been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain
or moisture, does not operate normally, or has been dropped.
15) CAUTION - These service instructions are for use by qualified service personnel only. To
reduce the risk of electric shock do not perform any servicing other than that contained in the
2
MINIFBQ FBQ800
MINIFBQ
Ultra-Compact 9-Band Graphic Equalizer with FBQ
FBQ800
V Ultra-compact 9.5" graphic equalizer for studio and stage applications
V Revolutionary FBQ Feedback Detection System instantly reveals critical
frequencies and can also be used as Audio Analyzer
V Additional Low Cut filter removes unwanted frequencies, e. g. floor rumble
V Accurate 6-digit LED Input/Output meters and Level control for precise level
indication
V High-quality illuminated faders, potentiometers and illuminated switches for
long-term reliability
V Ultra low-noise audio operational amplifiers offer outstanding sound
performance
V All Mini Series models can be stacked on top of each other to create an ultra-
compact signal processor solution
V High-quality components and exceptionally rugged construction ensure long
life
V Conceived and designed by BEHRINGER Germany
DEUTSCH
3
MINIFBQ FBQ800
FOREWORD
Dear Customer,
Thank you very much for expressing your confidence in
BEHRINGER products by purchasing the MINIFBQ
FBQ800.
Writing this foreword for you gives me great pleasure,
because it represents the culmination of many months of
hard work delivered by our engineering team to achieve a
very ambitious goal: presenting a graphic equalizer that
packs a lot of power in a compact and flexible unit. The
task of designing our new FBQ800 equalizer certainly meant
a great deal of responsibility, which we assumed by focusing
on you, the discerning user and musician. Meeting your
expectations also meant a lot of work and night shifts. But it
was fun, too. Developing a product usually brings a lot of
people together, and what a great feeling it is when
everybody who has participated in such a project can be
proud of what they’ve achieved.
It is our philosophy to share our enjoyment with you, because
you are the most important member of the BEHRINGER
team. With your highly competent suggestions for new
products you’ve made a significant contribution to help
guarantee you uncompromising quality, as well as excellent technical and audio properties at an
extremely reasonable price. All of this will enable you to give free rein to your creativity without being
hampered by budget constraints.
We are often asked how we manage to produce such high-quality devices at such unbelievably low
prices. The answer is quite simple: it’s you, our customers! Many satisfied customers mean large
sales volumes enabling us to get better purchasing terms for components, etc. Isn’t it only fair to
pass this benefit on to you? Because we know that your success is our success too!
I would like to thank all of those who have made the FBQ800 equalizer possible. You have all made
your own personal contributions, from the developers to the many other employees at this company,
and to you, the BEHRINGER user.
shape our company and make it successful. In return, we
My friends, it’s been worth the effort!
Thank you very much,
Uli Behringer
4
MINIFBQ FBQ800
TABLE OF CONTENTS
1. INTRODUCTION ..........................................................................................5
1.1 Before you begin................................................................................................................. 5
1.1.1 Shipment.................................................................................................................... 5
1.1.2 Initial operation........................................................................................................... 6
1.1.3 Online registration ..................................................................................................... 6
2. CONTROL ELEMENTS ................................................................................ 6
2.1 About the FBQ800............................................................................................................... 6
2.2 Front panel........................................................................................................................... 7
2.3 Rear panel ..........................................................................................................................11
3. SETUP EXAMPLE .....................................................................................12
4. AUDIO CONNECTIONS .............................................................................13
5. SPECIFICATIONS...................................................................................... 14
6. OTHER MINI PRODUCTS.......................................................................... 15
7. WARRANTY ............................................................................................... 16
1. INTRODUCTION
The MINIFBQ FBQ800 was designed with our experience and know-how in filter technology,
which spans many years. Our analog and digital equalizers are used the world over in reputable
radio and TV stations, studios, and PA systems. As with the rest of our product line, we put forth
uncompromising demands in terms of quality for the controls, the sound, the technical data, and the
fit and finish of the MINIFBQ FBQ800.
FBQ Feedback Detection System
The FBQ Feedback Detection System is one of the most outstanding characteristics of our graphic
equalizers. In this ingenious circuitry, LEDs on the frequency band faders identify high energy levels,
which indicate the likelihood of feedback. What was once a labor-intensive search for feedback is
now an activity that even a child could master. In addition, the MINIFBQ FBQ800 can replace an
audio analyzer in your audio setups.
Please read the manual carefully and keep it around for future reference.
DEUTSCH
1.1 Before you begin
1.1.1 Shipment
Your MINIFBQ FBQ800 was carefully packed at the factory, and the packaging was designed to
protect the unit from rough handling. Nevertheless, we recommend that you carefully examine the
packaging and its contents for any signs of physical damage that may have occurred during transit.
If the unit is damaged, please do NOT return it to BEHRINGER. Instead, notify your
dealer and the shipping company immediately. Otherwise, claims for damage or
replacement may not be honored.
Always use the original packing carton to prevent damage during storage or transport.
Make sure that no children are left unsupervised with the FBQ800 or its packaging.
Please ensure proper disposal of all packing materials.
1. INTRODUCTION
5
MINIFBQ FBQ800
1.1.2 Initial operation
Please make sure the unit is provided with sufficient ventilation, and never place the FBQ800 on top
of an amplifier or in the vicinity of a heater to avoid the risk of overheating. To power the FBQ800,
use only the power supply unit that is delivered with your equipment.
1.1.3 Online registration
Please do remember to register your new BEHRINGER equipment right after your purchase by
visiting www.behringer.com (alternatively www.behringer.de) and kindly read the terms and conditions
of our warranty carefully.
Should your BEHRINGER product malfunction, our goal is to have it repaired as quickly as possible.
To arrange for warranty service, please contact the retailer from whom the equipment was purchased.
Should your BEHRINGER dealer not be located in your vicinity, you may directly contact one of our
subsidiaries. Corresponding contact information is included in the original equipment packaging
(Global Contact Information/European Contact Information). Should your country not be listed, please
contact the distributor nearest you. A list of distributors can be found in the support area of our
website (www.behringer.com/support).
Registering your purchase and equipment with us helps us process your repair claims quicker and
more efficiently.
Thank you for your cooperation!
2. CONTROL ELEMENTS
This chapter introduces the FBQ800 and provides what you need to know about:
V using the FBQ800 (section 2.2 Front panel)
V setting up the FBQ800 (section 2.3 Rear panel)
Ensure that only qualified personnel set up and operate the FBQ800.
2.1 About the FBQ800
The FBQ800 is a graphic equalizer that you use to modify the strength and quality of audio signals.
More specifically, you can use the FBQ800 to:
V homogenize audio signals
V correct audio signals
V filter low-frequency audio signals (feedback, floor rumble, room resonance, and mains hum)
Input sources
The FBQ800 can receive signals from studio or Hi-Fi units. Some examples of these units include
mixers, soundcards, CD-players, and signal processors.
In this documentation, the signals that the FBQ800 receives are referred to as input signals. Audio
units that send input signals to the FBQ800 are referred to as input sources.
Output targets
The FBQ800 can send signals to studio or Hi-Fi units. Some examples of these units include mixers,
soundcards, and power amplifiers.
In this documentation, the signals that the FBQ800 sends are referred to as output signals. Audio
units that receive output signals from the FBQ800 are referred to as output targets.
6
2. CONTROL ELEMENTS
MINIFBQ FBQ800
2.2 Front panel
This section describes how to use the front panel of the FBQ800, illustrated as follows:
DEUTSCH
2. CONTROL ELEMENTS
7
MINIFBQ FBQ800
To monitor the input signal or, alternatively the output signal, use control elements
METER SELECT button: To select the type of signal you want to monitor, use this button,
which can appear:
V pushed in and illuminated: Monitor the input signal as soon as this signal enters the
FBQ800. The FBQ800 does not apply the LEVEL control or any other control elements to
the input signal that you monitor.
V not pushed in and not illuminated: Monitor the output signal as soon as this signal leaves
the FBQ800. The FBQ800 applies all control elements to the output signal that you monitor.
However, if you deactivated most of the control elements ( ), the input signal and the
output signal are the same.
IN/OUT meter: To monitor the level of the signal that you selected with the METER SELECT
button, use this stereo meter. Both the left (L) and right (R) sides of this meter share the same
decibel scale (- 24 dB to + 6 dB). If the signal level is too high, the CLIP LED illuminates.
and , as follows:
At 0 (zero) dB, the FBQ800 still has approximately 15 dB of headroom.
How to manage the signal level
Optimally, you want to maintain the signal level of the FBQ800 at 0 dB. When the signal level is:
V less than 0 dB, the signal is not full. If the difference between the level of the noise floor
and the level of the signal is not sufficient, you lose signal quality.
V greater than 0 dB, the CLIP LED illuminates on the IN/OUT meter. The signal can overload
the FBQ800. However, occasional clipping will not damage the sound quality.
Because sounds are not perfectly consistent, you cannot flawlessly maintain the signal level
at 0 dB. However, you can consistently manage the signal level. This involves monitoring and
adjusting the level of the input signal and the output signal, as follows:
1. To begin EQing in a neutral environment, set all frequency-band faders ( ) to 0 dB.
2. To protect the FBQ800 against signals that are unexpectedly high, turn the LEVEL control
( ) to -12 dB.
3. To monitor the input level, use the METER SELECT button ( ) together with the
IN/OUT meter ( ), as described in this documentation. If the input level is higher or
lower than 0 dB and you:
V can adjust the output level of the input source, adjust the output level of the input
source until the input level of the FBQ800 is 0 dB
V cannot adjust the output level of the input source, set the output level of the FBQ800
to 0 dB, as follows:
A. To activate all control elements, use the IN/OUT button ( ).
B. To monitor the output level of the FBQ800, use the METER SELECT button
( ) together with the IN/OUT meter ( ), as described in this documentation.
C. While you monitor the output level of the FBQ800, use the LEVEL knob ( ) to
adjust the output level of the FBQ800 to 0 dB.
4. If the frequency-band faders and all other control elements are not already activated, use
the IN/OUT button ( ) to activate them.
5. To EQ the signal, use the EQ section ( ), as described in this documentation.
6. To monitor the output level, use the METER SELECT button ( ) together with the
IN/OUT meter ( ), as described in this documentation. If the output level is higher or,
alternatively lower than 0 dB, use the LEVEL control ( ) to adjust the output level to 0 dB.
Most of the time, 0 dB is the optimal output level. However, the optimal level for
some output targets can be greater or less than 0 dB.
7. Periodically monitor and, if necessary, adjust the input level and output level, as described
previously in steps 3 and 6.
8
2. CONTROL ELEMENTS
MINIFBQ FBQ800
If you activated all control elements ( ), you can use control elements through to EQ the
input signal, as follows:
DEUTSCH
2. CONTROL ELEMENTS
9
MINIFBQ FBQ800
The following table is continued from the preceding page.
10
MINIFBQ FBQ800
2.3 Rear panel
This chapter describes what you need to know about setting up the FBQ800.
DEUTSCH
11
MINIFBQ FBQ800
3. SETUP EXAMPLE
The following graphically highlights the role of the FBQ800 in your audio setups:
12
MINIFBQ FBQ800
4. AUDIO CONNECTIONS
To connect audio units to the FBQ800, you can use patch cords that include the following types of
plugs:
V RCA (unbalanced)
V ¼" TS (unbalanced)
V ¼" TRS (balanced)
Illustrations of these plugs follow:
Fig. 4.1: Patch cord with RCA plugs
DEUTSCH
4. AUDIO CONNECTIONS
13
MINIFBQ FBQ800
5. SPECIFICATIONS
INPUT
Type ¼" TRS connectors (balanced) or
Impedance approx. 20 kΩ, balanced
CMRR 4 0 dB typ. @ 1 kHz
Max. input level +15 dBu
OUTPUT
Type ¼" TS connecotrs (unbalanced) or
Impedance approx. 120 Ω
Max. output level +15 dBu
SYSTEM SPECIFICATIONS
Frequency response 10 Hz to 200 kHz, -3 dB
Dynamic range 110 dB, 10 Hz to 22 kHz
Distortion 0.003 % typ. @ 0 dBu
Crosstalk < 80 dBu @ 1 kHz
Signal-to-noise ratio 10 Hz - 22 kHz < 95 dB @ 0 dBu, a-weighted
GRAPHIC EQUALIZER
Type 9 analog stereo bands
Control range ±6 dB or ±12 dB, switchable
Bandwidth 1 oct.
RCA connectors (unbalanced)
approx. 10 kΩ, unbalanced
RCA connectors (unbalanced)
OTHER FEATURES
Low-cut filter 75 Hz (12 dB/oct.)
Input level control -12 dB to +12 dB
POWER SUPPLY
Mains connection external power supply, 9 V ~ / 750 mA
Mains voltage
USA/Canada 120 V~, 60 Hz
U.K./Australia 240 V~, 50 Hz
China 220 V~, 50 Hz
Europe 230 V~, 50 Hz
Japan 100 V~, 50 - 60 Hz
Power consumption approx. 7.0 W
DIMENSIONS/WEIGHT
Dimensions (H x W x D) approx. 1 8/9" (48 mm) x 9 5/9" (243 mm) x 4 5/7" (120 mm)
Weight approx. 0.86 lbs. ( 0.39 kg)
BEHRINGER constantly strives to maintain the highest quality standards. Modifications may be made, if
necessary, without prior notice. The specifications and appearance of the equipment may therefore differ from
those listed or illustrated. from those listed or illustrated.
14
5. SPECIFICATIONS
MINIFBQ FBQ800
6. OTHER MINI PRODUCTS
The MINIFBQ belongs to the MINI suite of BEHRINGER products, which can operate together and are
introduced below:
MM
INIFEX FEX800INIFEX FEX800
M
INIFEX FEX800
MM
INIFEX FEX800INIFEX FEX800
Ultra-compact 9.5" stereo multi-effects processor for studio and stage applications
V 16 awesome FX presets in 24-bit/48 kHz resolution including reverb, delay, chorus,
flanger, phaser, rotary speaker, pitch shifter and multi-effects
V Intuitive FX Preset control with LED’s indicating the selected program
MM
INIAMP AMP800INIAMP AMP800
M
INIAMP AMP800
MM
INIAMP AMP800INIAMP AMP800
Ultra-compact 9.5" headphones amplifier system for studio and stage applications
V 4 totally independent stereo high-power amplifier sections
V Highest sonic quality even at maximum volume
MM
INICOM COM800INICOM COM800
M
INICOM COM800
MM
INICOM COM800INICOM COM800
Ultra-compact 9.5" stereo modeling compressor for studio and stage applications
V 16 awesome preset models for the most typical compression applications (vocal, drums,
guitar, keyboard, etc.)
V Dedicated Compressor Modeling control with LED’s indicating the selected dynamics
program
MM
INIMINIM
IC MIC M
M
INIM
MM
INIMINIM
Ultra-compact 9.5" microphone modeling preamp for studio and stage applications
V High-end preamplifier for all microphone, instrument and line-level sources. Perfectly
complements studio-grade condenser mics
V Ultra-flexible Preamp Modeling allows you to
quickly optimize your recordings
MINIMON MON800MINIMON MON800
MINIMON MON800
MINIMON MON800MINIMON MON800
Ultra-compact 9.5" monitor matrix mixer for
studio and stage applications
V Dedicated input section with 4 selectable and
mixable stereo inputs
V Accurate 6-digit LED main stereo output
meters for precise level indication
MM
INIBEAINIBEA
M
INIBEA
MM
INIBEAINIBEA
Ultra-compact 9.5" dual beat counter/phono
preamp for studio and stage applications
V Intelligent dual BPM counters with Tempo
Difference indicator
V Ultra-flexible Beat Assist and Sync Lock
functions
MINIMIX MIX800MINIMIX MIX800
MINIMIX MIX800
MINIMIX MIX800MINIMIX MIX800
Ultra-compact 9.5" karaoke machine for studio
and stage applications
V Revolutionary Voice Canceller—effectively
eliminates vocals from any stereo source
while retaining most music elements
V Integrated digital echo/reverb processor in
24-bit/40 kHz resolution for ultimate vocal
enhancement
IC M
IC MIC M
T BEAT BEA
T BEA
T BEAT BEA
IC800IC800
IC800
IC800IC800
T800T800
T800
T800T800
MINI products stack on top of each other
6. OTHER MINI PRODUCTS
15
DEUTSCH
MINIFBQ FBQ800
7. WARRANTY
1. This warranty does not exclude or limit the buyer’s statutory rights provided by national law, in
particular, any such rights against the seller that arise from a legally effective purchase contract.
2. The warranty regulations mentioned herein are applicable unless they constitute an infringement
of national warranty law.
Please do remember to register your new BEHRINGER equipment right after your purchase by
visiting www.behringer.com (alternatively www.behringer.de) and kindly read the terms and conditions
of our warranty carefully.
Registering your purchase and equipment with us helps us process your repair claims quicker and
more efficiently.
Thank you for your cooperation!
1. BEHRINGER (BEHRINGER International GmbH including all BEHRINGER subsidiaries listed on
the enclosed page, except BEHRINGER Japan) warrants the mechanical and electronic components
of this product to be free of defects in material and workmanship for a period of one (1) year* from
the original date of purchase, in accordance with the warranty regulations described below. If the
product shows any defects within the specified warranty period that are not excluded from this
warranty as described under § 5, BEHRINGER shall, at its discretion, either replace or repair the
product using suitable new or reconditioned parts. In the case that other parts are used which
constitute an improvement, BEHRINGER may, at its discretion, charge the customer for the additional
cost of these parts.
2. If the warranty claim proves to be justified, the product will be returned to the user freight prepaid.
3. Warranty claims other than those indicated above are expressly excluded.
1. To obtain warranty service, the buyer (or his authorized dealer) must call BEHRINGER (see
enclosed list) during normal business hours BEFORE returning the product. All inquiries must be
accompanied by a description of the problem. BEHRINGER will then issue a return authorization
number.
2. Subsequently, the product must be returned in its original shipping carton, together with the return
authorization number to the address indicated by BEHRINGER.
3. Shipments without freight prepaid will not be accepted.
1. Warranty services will be furnished only if the product is accompanied by a copy of the original
retail dealer’s invoice. Any product deemed eligible for repair or replacement under the terms of this
warranty will be repaired or replaced.
2. If the product needs to be modified or adapted in order to comply with applicable technical or
safety standards on a national or local level, in any country which is not the country for which the
product was originally developed and manufactured, this modification/adaptation shall not be
considered a defect in materials or workmanship. The warranty does not cover any such modification/
adaptation, irrespective of whether it was carried out properly or not. Under the terms of this warranty,
BEHRINGER shall not be held responsible for any cost resulting from such a modification/adaptation.
3. Free inspections and maintenance/repair work are expressly excluded from this warranty, in
particular, if caused by improper handling of the product by the user. This also applies to defects
caused by normal wear and tear, in particular, of faders, crossfaders, potentiometers, keys/buttons,
tubes, guitar strings, illuminants and similar parts.
§ 1 OTHER WARRANTY RIGHTS AND NATIONAL LAW
§ 2 ONLINE REGISTRATION
§ 3 WARRANTY
§ 4 RETURN AUTHORIZATION NUMBER
§ 5 WARRANTY REGULATIONS
16
7. WARRANTY
MINIFBQ FBQ800
4. Damages/defects caused by the following conditions are not covered by this warranty:
V improper handling, neglect or failure to operate the unit in compliance with the instructions
given in BEHRINGER user or service manuals.
V connection or operation of the unit in any way that does not comply with the technical or safety
regulations applicable in the country where the product is used.
V damages/defects caused by force majeure or any other condition that is beyond the control of
BEHRINGER.
5. Any repair or opening of the unit carried out by unauthorized personnel (user included) will void
the warranty.
6. If an inspection of the product by BEHRINGER shows that the defect in question is not covered by
the warranty, the inspection costs are payable by the customer.
7. Products which do not meet the terms of this warranty will be repaired exclusively at the buyer’s
expense. BEHRINGER will inform the buyer of any such circumstance. If the buyer fails to submit a
written repair order within 6 weeks after notification, BEHRINGER will return the unit C.O.D. with a
separate invoice for freight and packing. Such costs will also be invoiced separately when the buyer
has sent in a written repair order.
§ 6 WARRANTY TRANSFERABILITY
This warranty is extended exclusively to the original buyer (customer of retail dealer) and is not
transferable to anyone who may subsequently purchase this product. No other person (retail dealer,
etc.) shall be entitled to give any warranty promise on behalf of BEHRINGER.
§ 7 CLAIM FOR DAMAGES
Failure of BEHRINGER to provide proper warranty service shall not entitle the buyer to claim
(consequential) damages. In no event shall the liability of BEHRINGER exceed the invoiced value of
the product.
DEUTSCH
* Customers in the European Union please contact BEHRINGER Germany Support for further details.
T echnical specifications and appearance subject to change without notice. The information contained
herein is correct at the time of printing. The names of companies, institutions or publications pictured
or mentioned and their respective logos are registered trademarks of their respective owners. Their
use neither constitutes a claim of the trademarks by BEHRINGER® nor affiliation of the trademark
owners with BEHRINGER®. BEHRINGER® accepts no liability for any loss which may be suffered by
any person who relies either wholly or in part upon any description, photograph or statement contained
herein. Colours and specification may vary slightly from product. Products are sold through our
authorised dealers only. Distributors and dealers are not agents of BEHRINGER® and have absolutely
no authority to bind BEHRINGER® by any express or implied undertaking or representation. No part
of this manual may be reproduced or transmitted in any form or by any means, electronic or
mechanical, including photocopying and recording of any kind, for any purpose, without the express
written permission of BEHRINGER Spezielle Studiotechnik GmbH. BEHRINGER® is a registered
trademark.
ALL RIGHTS RESERVED. © 2005 BEHRINGER Spezielle Studiotechnik GmbH,
Hanns-Martin-Schleyer-Str. 36-38, 47877 Willich-Münchheide II, Germany.
Tel. +49 2154 9206 0, Fax +49 2154 9206 4903
7. WARRANTY
17
Loading...