Behringer BB 560M Service Manual
Quick Start Guide
BB 560M
High-Quality Professional Headphones with
Built-in Microphone
Controls and Connectors
(1)
(3)(2) (4)
(5) (6)(7)
(1) Volume + / Next song - Press quickly to increase
the volume, press and hold to skip to the next song.
(4) 3.5 mm input - Connect a 3.5 mm stereo cable for
wired audio use.
(2) Play/Pause - Used for several functions including
Bluetooth pairing, play, pause, hang up, refuse call,
and redial. Hold this button for 1 second to turn the
headphones on.
(3) Volume - / Previous song - Press quickly to
decrease volume, press and hold for previous song.
V 2.0
(5) LED - Red and blue status indicator light.
(6) Microphone
(7) USB port - Micro USB port for charging.
Charging
Bluetooth wireless call
After unpacking the headphones, the USB charging cable should
be plugged in and allowed to charge for at least 4 hours. O nce the
batter y has been fully charged the rst time, subs equent charges
should only take 2-3 hours. While charging, the LED will light red.
After the battery has reached full capacity, the LED will tur n o.
The headset will beep twice to indicate that the battery power is
low, and the LED will ash red. When the voltage drops below 3 V,
the headset will automatically p ower o and must be recharged.
Pairing of headset and Bluetooth device
1. Turn on the headphones by holding the Play/Pause button
for 1 second. The LED will alternate ashing red and blue and
a sound will beep twice to indic ate that the device is ready
for pairing.
2. Open the Bluetooth menu on your Bluetooth device and search
for available connections. Note that if the headset does not
successfully pair with a device, it will automatically power
down after 3 minutes.
3. S elect "BB 560M" from the list. When pairing is successful,
the headset will beep once and the LED will light blue. If a
password is required, use "0000".
Once the headset has been success fully pair with another device,
it will automatically try to connect to this same device when the
headset is powered o and powered on again.
When the Bluetooth headset is paired and connec ted with your
mobile phone, you can use the headse t to accept phone calls in
addition to lis tening to music.
Outgoing calls
1. To make a new call while using the headset, dial a number
as usual. A ringing tone will be heard in the headset and the
voice audio and mic rophone will automatically be switched to
the headset. (note that some phones re quire the switch to be
conrmed manually on the screen)
2. To redial the last number, double click the Play/Pause
button to dial out the last dialing phone number. (Some
mobile phones may only require a single press of the but ton.)
Answering and hanging up calls
1. When the phone rings, press the Play/Pause button once
or press the phone answer key to answer the phone.
2. To rejec t the call, press and hold the Play/Pause but ton for
1 second.
3. To end a call, press the Play/Pause button or press the
hang up button on the phone screen. After the call ends, any
music that was playing prior to the call will resume.
IMPORTANT SAFETY INFORMATION
4. Read these instructions.
5. Keep these instructions.
6. Heed all warnings.
7. Follow all instruc tions.
8. Do not use this apparatus near water.
9. Clean only with dry cloth.
10. Do not throw this product in the re, to avoid ex plosion.
11. Do not expose this product to bright sunshine for a long time.
12. Do not disass emble or modify this product.
13. Please store this product in a clean and dry environment.
14. WARNING! To prevent possible hearing damage, do not listen
at high volume levels for long periods.
Loading...