Beckhoff CU8880-0010 Installation And Operating Instructions Manual

Installation- and Operating instructions for

CU8880-0010

Ethernet Controller with USB Input

Version: 1.4
Date: 2018-04-12

Table of contents

Table of contents

1.

2.

3.

4.

5.

General instructions 2

Notes on the Documentation 2

Liability Conditions 2
Trademarks 2
Patent Pending 2
Copyright 2
State at Delivery 2
Delivery conditions 2

Description of safety symbols 3

Product Description 4

Product Overview 4
Power Supply 5
Data connectors 5

USB type B Port (X20) (standard-cable) 5
RJ 45-Port (X10) (standard CAT5-cable) 5

LED Diagnostics 6

Installation Instructions 7

Transport and Unpacking 7

Transport 7
Unpacking 7

Mounting / Unmounting 8
Connecting devices 9

Connecting cables 9

Operating Instructions 10

Configuration 10

Appendix 11

Assembly dimensions 11
Service and Support 12

Beckhoff's branch offices and representatives 12
Beckhoff headquarters 12
Beckhoff Support 12
Beckhoff Service 12

Technical data 13
Approvals for USA and Canada 13

FCC: Federal Communications Commission Radio Frequency Interference
Statement 13
FCC: Canadian Notice 13

CU8880-0010 1

General instructions

General instructions

Notes on the Documentation

This description is only intended for the use of trained specialists in control

and automation engineering who are familiar with the applicable national
standards. It is essential that the following notes and explanations are
followed when installing and commissioning these components.
The responsible staff must ensure that the application or use of the
products described satisfy all the requirements for safety, including all the
relevant laws, regulations, guidelines and standards.

Liability Conditions

The documentation has been prepared with care. The products described

are, however, constantly under development. For that reason the
documentation is not in every case checked for consistency with
performance data, standards or other characteristics. In the event that it
contains technical or editorial errors, we retain the right to make alterations
at any time and without warning. No claims for the modification of products
that have already been supplied may be made on the basis of the data,
diagrams and descriptions in this documentation.
All pictures shown in the documentation are exemplary. Illustrated
configurations can differ from standard.

Trademarks

Beckhoff®, TwinCAT®, EtherCAT®, Safety over EtherCAT®, TwinSAFE®

and XFC® are registered trademarks of and licensed by Beckhoff
Automation GmbH.
Other designations used in this publication may be trademarks whose use
by third parties for their own purposes could violate the rights of the
owners.

Patent Pending

The EtherCAT Technology is covered, including but not limited to the

following patent applications and patents:
EP1590927, EP1789857, DE102004044764, DE102007017835
with corresponding applications or registrations in various other countries.
The TwinCAT Technology is covered, including but not limited to the
following patent applications and patents:
EP0851348, US6167425 with corresponding applications or registrations in
various other countries.

Copyright

© Beckhoff Automation GmbH & Co.KG.

The reproduction, distribution and utilization of this document as well as the
communication of its contents to others without express authorization are
prohibited. Offenders will be held liable for the payment of damages. All
rights reserved in the event of the grant of a patent, utility model or design.

State at Delivery

All the components are supplied in particular hardware and software

configurations appropriate for the application. Modifications to hardware or
software configurations other than those described in the documentation
are not permitted, and nullify the liability of Beckhoff Automation
GmbH & Co.KG.

Delivery conditions

In addition, the general delivery conditions of the company Beckhoff

Automation GmbH & Co.KG apply.

2 CU8880-0010

General instructions

Description of safety symbols

The following safety symbols are used in this operating manual. They are

intended to alert the reader to the associated safety instructions.

Danger

This symbol is intended to highlight risks for the life or health of personnel.

Warning

This symbol is intended to highlight risks for equipment, materials or the
environment.

i

Note

This symbol indicates information that contributes to better understanding.

CU8880-0010 3