BECKHOFF CU8871-0000 User Manual

Installation- and Operating instructions for
CU8871-0000
CFast card adapter with USB connector
Version: 1.1 Date: 2013-12-06
Table of contents
Table of contents
1 Foreword 3
1.1 Notes on the Documentation 3
1.1.1 Liability Conditions 3
1.1.2 Trademarks 3
1.1.3 Patent Pending 3
1.1.4 Copyright 3
1.1.5 State at Delivery 3
1.1.6 Delivery conditions 3
1.2 Description of safety symbols 4
1.3 Operator’s obligation to exercise diligence 4
2 Product Description 5
2.1 Product Overview 5
2.2 Connections 6
2.2.1 Power Supply 6
2.2.2 USB 3.0 type B Port (X10) (Standard Cable) 7
2.2.3 CFast card slot (X20) (Standard CFast Interface) 7
2.3 Compact-Flash card 8
2.3.1 Inserting the CFast Card 8
2.3.2 Ejecting the CFast Card 8
3 Installation 9
3.1 Transport and Unpacking 9
3.1.1 Transport 9
3.1.2 Unpacking 9
3.2 Mounting/ Demounting 10
3.3 Connecting devices 11
3.3.1 Connecting cables 11
3.3.2 Connecting Power Supply 11
4 Operation 12
4.1 Connection to Host 12
4.2 LED Diagnosis 12
4.3 Maintenance 13
4.3.1 Cleaning 13
4.3.2 Maintenance 13
4.4 Shutting down 13
4.4.1 Disposal 13
5 Dimensions 14
CU8871-0000 1
Table of contents
6 Technical Data 15
7 Appendix 16
7.1 Beckhoff Support and Service 16
7.1.1 Beckhoff branches and partner companies 16
7.1.2 Beckhoff company headquarters 16
7.2 Approvals for USA and Canada 17
7.3 FCC Approval for USA 17
7.4 FCC Approval for Canada 17
2 CU8871-0000

Foreword

1 Foreword
1.1 Notes on the Documentation
This description is only intended for the use of trained specialists in control and automation engineering who are familiar with the applicable national standards. It is essential that the following notes and explanations are followed when installing and commissioning these components.
The responsible staff must ensure that the application or use of the products described satisfy all the requirements for safety, including all the relevant laws, regulations, guidelines and standards.
1.1.1 Liability Conditions
The documentation has been prepared with care. The products described are, however, constantly under development. For that reason the documentation is not in every case checked for consistency with performance data, standards or other characteristics. In the event that it contains technical or editorial errors, we retain the right to make alterations at any time and without warning. No claims for the modification of products that have already been supplied may be made on the basis of the data, diagrams and descriptions in this documentation.
1.1.2 Trademarks
Beckhoff®, TwinCAT®, EtherCAT®, Safety over EtherCAT®, TwinSAFE® and XFC® are registered trademarks of and licensed by Beckhoff Automation GmbH. Other designations used in this publication may be trademarks whose use by third parties for their own purposes could violate the rights of the owners.
1.1.3 Patent Pending
The EtherCAT Technology is covered, including but not limited to the following patent applications and patents: EP1590927, EP1789857, DE102004044764, DE102007017835 with corresponding applications or registrations in various other countries. The TwinCAT Technology is covered, including but not limited to the following patent applications and patents: EP0851348, US6167425 with corresponding applications or registrations in various other countries.
1.1.4 Copyright
©
Beckhoff Automation GmbH. The reproduction, distribution and utilization of this document as well as the communication of its contents to others without express authorization are prohibited. Offenders will be held liable for the payment of damages. All rights reserved in the event of the grant of a patent, utility model or design.
1.1.5 State at Delivery
All the components are supplied in particular hardware and software configurations appropriate for the application. Modifications to hardware or software configurations other than those described in the documentation are not permitted, and nullify the liability of Beckhoff Automation GmbH.
1.1.6 Delivery conditions
In addition, the general delivery conditions of the company Beckhoff Automation GmbH apply.
CU8871-0000 3
Foreword
1.2 Description of safety symbols
The following safety symbols are used in this operating manual. They are intended to alert the reader to the associated safety instructions.
Acute risk of injury!
If you do not adhere the safety advise adjoining this symbol, there is immediate
DANGER
WARNING
CAUTION
danger to life and health of individuals!
Risk of injury!
If you do not adhere the safety advise adjoining this symbol, there is danger to life and health of individuals!
Hazard to individuals!
If you do not adhere the safety advise adjoining this symbol, there is obvious hazard to individuals!
Hazard to devices and environment
If you do not adhere the notice adjoining this symbol, there is obvious hazard to
Attention
Note
materials and environment.
Note or pointer
This symbol indicates information that contributes to better understanding.
1.3 Operator’s obligation to exercise diligence
The operator must ensure that
the product is only used as intended (see chapter Product Description)
the product is in a sound condition and in working order during operation (see chapter
Maintenance)
the product is operated, maintained and repaired only by suitably qualified and authorized personnel
the personnel is instructed regularly about relevant occupational safety and environmental protection aspects, and is familiar with the operating manual and in particular the safety notes contained herein
the operation manual is in good condition and complete, and always available for reference at the location of the product
none of the safety and warning notes attached to product are removed, and that all notes remain legible.
4 CU8871-0000

Product Description

2 Product Description
2.1 Product Overview
The CU8871-0000 offers a CFast socket with USB connector in a compact housing for DIN rail mounting. CFast Flash cards are used in the industrial environment as data memory for process and control data. The CFast cards are hot-plug capable in the CU8871 and can hence be plugged and unplugged like removable data storage devices for exchanging data with other PCs during operation.
The USB 3.0 connection offers the highest data transfer rate possible with a CFast card, but the CFast card adapter can also be connected to PCs with a USB 2.0 interface. Power is also supplied via USB. Status LEDs indicate whether the CU8871 is connected in addition to indicating data accesses and providing information on the write protection of the inserted CFast card.
Other outstanding features are:
user-friendly installation via integrated DIN rail adapter
no power supply needed – the box is supplied by USB (5V DC)
USB 3.0 input for compatibility to all USB standards
standard USB cable for data exchange
compact industrial design.
CU8871-0000 5
Product Description
)
2.2 Connections
2.2.1 Power Supply
LED (P10
USB (1)
The USB-CFast card adapter does not need any additional power supply. The power supply (5V DC) is realized by the USB connector (1). The LED P10 lights green when power supply is connected.
2.2.1.1 Power consumption
The power consumption of the device depends on the media plugged in the reader. The table shows the values:
Media State Current consumption Power consumption
None Standby 2mA 10mW
CFast card Idle 1mA 5mW
CFast card Access 20mA 100mW
2.2.1.2 UL Requirements
UL Requirements
To meet the UL requirements, the device must not be connected to unlimited power
Attention
sources!
6 CU8871-0000
Product Description
(
X20)
2.2.2 USB 3.0 type B Port (X10) (Standard Cable)
2
3
Shield
1
4
Pin Assignment
1 VCC
2 Data -
3 Data +
4 GND
Shell Shield
2.2.3 CFast card slot (X20) (Standard CFast Interface)
CFast Slot
Signal
Pin
Function
1 GND - Ground 18 A02 I I1Z 35 -IOWR I I3U
2 D03 I/O I1Z,0Z3 19 A01 I I1Z 36 -WE I I3U
3 D04 I/O I1Z,0Z3 20 A00 I I1Z 37 Ready O OT1
4 D04 I/O I1Z,0Z3 21 D00 I/O I1Z,OZ3 38 Vcc - Power
5 D06 I/O I1Z,0Z3 22 D01 I/O I1Z,OZ3 39 -CSEL I I2Z
6 D07 I/O I1Z,0Z3 23 D02 I/O I1Z,OZ3 40 -VS2 O Open
7 -CE1 I I3U 24 WP O OT3 41 RESET I I2Z
8 A10 I I1Z 25 -CD2 O Ground 42 -WAIT O OT1
9 -OE I I3U 26 -CD1 O Ground 43 -INPACK O OT1
10 A09 I I1Z 27 D11 I/O I1Z,OZ3 44 -REG I I3U
11 A08 I I1Z 28 D12 I/O I1Z,OZ3 45 BVD2 O OT1
12 A07 I I1Z 29 D13 I/O I1Z,OZ3 46 BVD1 O OT1
13 Vcc - Power 30 D14 I/O I1Z,OZ3 47 DO8 I/O I1Z,OZ3
14 A06 I I1Z 31 D15 I/O I1Z,OZ3 48 DO9 I/O I1Z,OZ3
15 A05 I I1Z 32 -CE2 I I3U 49 D10 I/O I1Z,OZ3
16 A04 I I1Z 33 -VS1 O Ground 50 GND - Ground
17 A03 I I1Z 34 -IORD I I3U
Pin Type
In, Out Type
Pin
Signal Function
Pin Type
In, Out Type
Pin
Signal Function
Pin Type
In, Out Type
CU8871-0000 7
Product Description
2.3 Compact-Flash card
The Compact-Flash card (CFast card) is a non-volatile memory media. Data to be retained in the event of a power failure should be saved on the CFast card. The CFast card operates similar to a hard disk.
Only use CFast cards that are made for industrial use
It is recommended only use CFast cards that are made for industrial use. They
Note
2.3.1 Inserting the CFast Card
The CFast card must be inserted carefully upright with the written side to the left in the CFast slot. The slot has a protection to ensure the right inserting direction. The card can only be inserted wrong direction with violence.
possess a higher number of read / write cycles and an enhance temperature range (up to + 85°C).
A proper operation of the device can only be guaranteed with the use of CFast cards from Beckhoff Automation GmbH!
As soon as the card is inserted, the LED (P20) lights up green. The red LED (P21) flashes up shortly, too.
2.3.2 Ejecting the CFast Card
For ejecting press on the CFast card.The card now can be removed from the slot. The green LED (P20) goes off when the card is removed.
8 CU8871-0000

Installation

3 Installation
3.1 Transport and Unpacking
The specified storage conditions must be observed (see chapter Technical Data).
3.1.1 Transport
Despite the robust design of the unit, the components are sensitive to strong vibrations and impacts. During transport, the unit should therefore be protected from excessive mechanical stress. Therefore, please use the original packaging.
Danger of damage to the unit
If the device is transported in cold weather or is exposed to extreme variations in
Attention
Prior to operation, the unit must be allowed to slowly adjust to room temperature. Should condensation occur, a delay time of approximately 12 hours must be allowed before the unit is switched on.
temperature, make sure that moisture (condensation) does not form on or inside the device.
3.1.2 Unpacking
Proceed as follows to unpack the unit:
1. Remove packaging
2. Do not discard the original packaging. Keep it for future relocation
3. Check the delivery for completeness by comparing it with your order
4. Please keep the associated paperwork. It contains important information for handling the unit
5. Check the contents for visible shipping damage.
If you notice any shipping damage or inconsistencies between the contents and your order, you should notify Beckhoff Service.
CU8871-0000 9
Installation
3.2 Mounting/ Demounting
The USB-CFast adapter CU8871-0000 can be snapped onto a 35 mm mounting rail conforms to EN 50022:
To release the CU8871-0000 from the mounting rail:
1. first pull the lug at the bottom of the hub downwards by using a screw driver (1)
2. then pull the hub from the mounting rail (2).
10 CU8871-0000
Installation
3.3 Connecting devices
The power supply plug must be withdrawn
Please read the documentation for the external devices prior to connecting them!
Attention
3.3.1 Connecting cables
The connections are documented in the section Product Description.
When connecting the cables to the CU8871-0000, proceed according to the following sequence:
Switch off all the devices that are to be connected
During thunderstorms, plug connector must neither be inserted nor removed!
When disconnecting a plug connector, always handle it at the plug. Do not pull the cable!
Disconnect all the devices that are to be connected from the power supply
Connect all the cables between the CU8871-0000 and the devices that are to be connected
Reconnect all devices to the power supply.
3.3.2 Connecting Power Supply
The power supply is realized by the USB connector.
First establish USB connection
The USB connection between the Industrial PC and the CU8871-0000 should be
Note
established before switching the PC on, otherwise over-current messages can be displayed.
CU8871-0000 11

Operation

4 Operation
4.1 Connection to Host
The CFast card adapter is connected to a USB host via a standard USB cable. The maximum length for the wire is 5 meters. For correct operation, use USB 3.0 suitable wire.
4.2 LED Diagnosis
LED Mapping Status Meaning
off no power supply connected (see chapter Power Supply for details) P10 Power supply
lights green device is operational
off no CFast card inserted P20 CF LOCK
lights green CFast card is inserted and electrical connected
off no access on the CFast card P21 ACCESS
flashes red read / write access on the CFast card
12 CU8871-0000
Operation
4.3 Maintenance
4.3.1 Cleaning
Disconnect power supply
Switch off the device and all connected devices, and disconnect the device from the
DANGER
The device can be cleaned with a soft, damp cloth. Do not use any aggressive cleaning materials, thinners, scouring material or hard objects that could cause scratches.
power supply.
4.3.2 Maintenance
The CU8871-0000 USB-CFast adapter is maintenance-free.
4.4 Shutting down
4.4.1 Disposal
Observe national electronics scrap regulations
Observe the national electronics scrap regulations when disposing of the device.
Note
In order to dispose of the device, it must be removed and fully dismantled:
Housing components (polycarbonate, polyamide (PA6.6)) are suitable for plastic recycling
Metal parts can be sent for metal recycling
Electronic parts such as disk drives and circuit boards must be disposed of in accordance with
national electronics scrap regulations.
CU8871-0000 13

Dimensions

5 Dimensions
The product is characterized by small overall installed size. With a height of 100 mm, the module dimensions exactly match those of the Beckhoff Bus Terminals. Together with the lowered connector surfaces, this means that it can be used in a standard terminal box with a height of 120 mm
.
14 CU8871-0000

Technical Data

6 Technical Data
Product name CU8871-0000
Number of USB type B ports 1
Number of CFast-card slots 1
Supported standards USB1.1, USB2.0, USB3.0
Supported baud rates USB 12 Mbit/s, 480 Mbit/s, 5 Gbit/s
Status display 3 LEDs
Cable length USB maximum 5 meters
Power supply Max. current input from 5V USB maximum 500mA @ 5V DC (for details see chapter Power
Dimensions (W x H x D) app. 34 mm x 100 mm x 76 mm
Weight app. 95 g
Permissible ambient temperature 0°C to +55°C (operation)
Permissible relative humidity 5% to 95%, no condensation
EMC resistance burst / ESD EN 60000-6-2 / EN 60000-6-4
Vibration / Shock resistance EN 60068-2-6 / EN 60068-2-27
Assembly on 35 mm mounting rail conforms to EN 50022
Installation position any
Protection class IP20
Approvals CE, UL (for details see chapter UL Requirements)
by USB (5 V DC)
Supply)
(with lug for mounting rail release)
-25°C to +70°C (transport/ storage)
CU8871-0000 15

Appendix

7 Appendix
7.1 Beckhoff Support and Service
Beckhoff and their partners around the world offer comprehensive support and service, making available fast and competent assistance with all questions related to Beckhoff products and system solutions.
7.1.1 Beckhoff branches and partner companies
Please contact your Beckhoff branch office or partner company for local support and service on Beckhoff products! The contact addresses for your country can be found in the list of Beckhoff branches and partner companies: www.beckhoff.com
7.1.2 Beckhoff company headquarters
Beckhoff Automation GmbH Eiserstraße 5 33415 Verl Germany
. You will also find further documentation for Beckhoff components there.
Phone: + 49 (0) 5246/963-0 Fax: + 49 (0) 5246/963-198 E-mail: info@beckhoff.de Web: http://www.beckhoff.de/
Beckhoff Support
Support offers you comprehensive technical assistance, helping you not only with the application of individual Beckhoff products, but also with other, wide-ranging services:
world-wide support
design, programming and commissioning of complex automation systems
and extensive training program for Beckhoff system components
Hotline: + 49 (0) 5246/963-157 Fax: + 49 (0) 5246/963-9157 E-mail: support@beckhoff.com
Beckhoff Service
The Beckhoff Service Center supports you in all matters of after-sales service:
on-site service
repair service
spare parts service
hotline service
Hotline: + 49 (0) 5246/963-460 Fax: + 49 (0) 5246/963-479 E-mail: service@beckhoff.com
If servicing is required, please quote the project number of your product.
16 CU8871-0000
Appendix
7.2 Approvals for USA and Canada
7.3 FCC Approval for USA
FCC: Federal Communications Commission Radio Frequency Interference Statement
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
Technical modifications
Technical modifications to the device may cause the loss of the FCC approval.
Note
7.4 FCC Approval for Canada
FCC: Canadian Notice
This equipment does not exceed the Class A limits for radiated emissions as described in the Radio Interference Regulations of the Canadian Department of Communications.
CU8871-0000 17
Loading...