Bauknecht GMX 5597/1 Quick Reference Manual
GB
Quick Reference Guide
Before using the dishwasher, read the user instructions!
(We reserve the right to make technical modifications)
5019 496 96032
GMX 5597/1
Add regeneration salt
Only add regeneration salt immediately before
starting a wash programme.
Add rinse aid
“Half Load” function
Recommended when the dishwasher is not full to
save water and electricity. When it is selected
(indicator lamp on), only the upper rack or the
lower rack will be washed.
WARN ING : This function remains selected until
switched off.
Antibacterial Rinse
(Sani Rinse option)
This function adds an antibacterial rinse at the
end of the wash cycle, thereby further reducing
bacteria levels. The lamp will light up when the
function is activated. If the temperature is not
maintained during the antibacterial cycle (e.g. if
the door is opened or a power failure occurs),
the lamps will start blinking to indicate that the
antibacterial action is not guaranteed.
“Delayed start” and “Water
hardness setting” button
To set the water hardness level, follow the
instructions in the enclosed handbook. The wash
cycle can be programmed to start after 1-9 hours.
The delayed start can be programmed either before
or after selecting the desired wash programme.
When the door is closed, a pre-wash cycle is run,
after which the delayed start countdown begins.
Water stop device activated
Switch off the dishwasher and contact the After-Sales
Service.
The dishwasher over fills with water
Reset and start the programme again from the beginning.
If the problem persists, contact the After-Sales Service.
The water heating system is not working
Reset and start the programme again from the beginning.
If the problem persists, contact the After-Sales Service.
Water heating anomaly
Reset and start the programme again from the beginning.
If the problem persists, contact the After-Sales Service.
The dishwasher does not fill with water
Check the water supply and filters, and make sure that
there are no kinks in the water inlet hose. Open and
close the door in order to continue.
The dishwasher does not drain
Make sure that the filter unit and drain hose are not
clogged and if necessary clean them.
Flow meter
(if provided)
anomaly
Reset and start the programme again from the beginning.
If the problem persists, contact the After-Sales Service.
Alternate washing system
(if provided)
anomaly
Reset and start the programme again from the beginning.
If the problem persists, contact the After-Sales Service.
Fault in water load system
Switch off the dishwasher and contact the After-Sales
Service.
(*) Options available with all programmes, except prewash.
(**) When the “AutoSensor” programme is selected, wash
parameters automatically adapt to the level of soiling present.
1) Reference programme for energy label in compliance with
EN 50242 regulations (upper rack in upper position);
2) Refer to “User instructions”;
3) Programme data obtained in conformity with European
standard EN 50242. Values may vary in relation to usage, e.g.:
different loads, water temperatures - above or below 15° C as well as water hardness and power supply voltage, etc.
On/Off button
Press the ON button to switch on the dishwasher.
The indicator lamp of the last programme selected
lights up; at the end of the cycle a short acoustic
signal sounds.
Programme selection button
Press the button to select a programme.
The corresponding indicator lamp lights up.
Indicators
Additional options (*)
Fault indicators
Indicators
Off
Blinking
On
Programme chart
Detergent
2)
Consumption
3)
Programmes Loading Instructions A B Litres kWh Minutes
Pre-Rinse cold
Crockery to be washed later.
- - 6.0 0.03 16
Rapid 30 min 45°C
Lightly soiled crockery with no dried-on food.
X - 13.0 0.80 30
Bio/Eco
1)
55°C
Normally soiled crockery.
X X 14.0 1.08 180
AutoSensor 60-70°C
Normally or heavily soiled crockery.
X X (**) (**) (**)
Intensive 70°C
Recommended programme for heavily soiled
crockery, especially suitable for pans and saucepans.
X X 20.0 1.60 110
49696032GB.fm Page 1 Monday, August 24, 2009 7:34 PM
Black process 45.0° 150.0 LPI
How to use the appliance
Further indications are given in the single chapters and in the user instructions.
Press the
On/Off
button .
Large compartment
A
Small compartment
B
Mechanical indicator lamp C.
Electric indicator on control panel (if provided).
On models with water softener system
only.
Mechanical indicator lamp D.
Electric indicator on control panel
(if provided).
Refer to the dishwasher loading instructions.
Press the button until the desired programme lights up.
If necessary (and if provided). The corresponding indicator lamp lights up/
The relative information appears on the display.
“Cancel”
Open the door, press until the
indicator lamps 4 + 5 (marked by
“end” on the control panel) light up.
Close the door, after about 1 min.
the dishwasher cycle ends.
“Change programme in progress”
Open the door.
Select another programme and close
the door in order to start the new
cycle.
- Only open the dishwasher if
necessary (Warning: beware of
hot steam).
- If the appliance is switched off
during a wash cycle, when
switched on again it will resume
the cycle from where it was
interrupted.
At the end of the programme a short acoustic signal will sound.
The indicator lamps 4 + 5 (marked by “end” on the control panel)
light up.
Open the door and press the
On/Off
button .
All the indicator lamps go off.
Warning: When the door is opened steam comes out!
Unload the appliance, starting from the lower rack.
Open the door
How to fill the
detergent dispenser
BA
C
Check the rinse aid level
Check the
regeneration salt level
D
Load the racks
Select a programme
Select
additional options
Turn on the water tap,
then close the door to
start the programme
Wash cycle
Switch off the appliance
Turn off the water
tap, unload the racks
49696032GB.fm Page 2 Monday, August 24, 2009 7:34 PM
Black process 45.0° 150.0 LPI
Loading...