Page 1
®
A
Veerr
A
V
Meeddiiaa
M
®
A
A
Veerr
V
Viissiioonn333300
V
English
UUsseerr M
Maannuuaall
Digital Document Camera
Page 2
A
P/N 300AACD
Made in Taiwan
Page 3
FCC NOTICE (Class B)
This device has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a commercial,
industrial or business environment. This equipment can generate, use and
radiate radio frequency energy and, if not installed and used in accordance with the
instruction, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may cause
undesired operation.
CAUTION ON MODIFICATIONS
To comply with the limits for the Class B digital device, pursuant to Part 15 of the FCC
Rules, this device must be installed in computer equipment certified to comply with the
Class B limits. All cables used to connect the computer and peripherals must be
shielded and grounded. Operation with non-certified computers or non-shielded cables
may result in interference to radio or television reception.
English Deutsch Français Italiano Español
Any changes or modifications not expressly approved by the grantee of this device
could void the user's authority to operate the equipment.
CE NOTICE
This is a Class B product.
DISCLAIMER
No warranty or representation, either expressed or implied, is made with respect to the
contents of this documentation, its quality, performance, merchantability, or fitness for a
particular purpose. Information presented in this documentation has been carefully
checked for reliability; however, no responsibility is assumed for inaccuracies. The
information contained in this documentation is subject to change without notice.
In no event will AVerMedia be liable for direct, indirect, special, incidental, or
consequential damages arising out of the use or inability to use this product or
documentation, even if advised of the possibility of such damages.
TRADEMARKS
AVerMedia and AVerVision are registered trademarks of AVerMedia TECHNOLOGIES,
Inc. IBM PC is a registered trademark of International Business Machines Corporation.
Macintosh is a registered trademark of Apple Computer, Inc. Microsoft is a registered
trademark and Windows is a trademark of Microsoft Corporation. All other products or
corporate names mentioned in this documentation are for identification and explanation
purposes only, and may be trademarks or registered trademarks of their respective
owners.
COPYRIGHT
© 2004 by AVerMedia TECHNOLOGIES, Inc. All rights reserved. No part of this
publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or
translated into any language in any form by any means without the written permission of
AVerMedia TECHNOLOGIES, Inc.
Page 4
THE MARK OF CROSSED-OUT WHEELED BIN INDICATES THAT THIS
PRODUCT MUST NOT BE DISPOSED OF WITH YOUR OTHER
HOUSEHOLD WASTE. INSTEAD, YOU NEED TO DISPOSE OF THE
WASTE EQUIPMENT BY HANDING IT OVER TO A DESIGNATED
COLLECTION POINT FOR THE RECYCLING OF WASTE ELECTRICAL
AND ELECTRONIC EQUIPMENT. FOR MORE INFORMATION ABOUT
WHERE TO DROP OFF YOUR WASTE EQUIPMENT FOR RECYCLING,
PLEASE CONTACT YOUR HOUSEHOLD WASTE DISPOSAL SERVICE OR
THE SHOP WHERE YOU PURCHASED THE PRODUCT.
Battery Safety Information
- Store the batteries in a cool dry place.
- Do not dispose of used batteries in domestic waste. Dispose of batteries at
special collection points or return to point of sale if applies.
- Remove the batteries during long periods of non-use. Always remove exhausted
batteries from the remote control. Battery leakage and corrosion can damage
this remote control, dispose of batteries safely.
- Do not mix old and new batteries.
- Do not mix different types of batteries: alkaline, standard (carbon-zinc) or
rechargeable (nickel-cadmium).
- Do not dispose of batteries in a fire. The batteries may explode or leak.
- Never short circuit the battery terminals.
Remote Control Laser Safety Information
CAUTION: Laser beam is emitted when the laser button of the remote control is pressed.
DO NOT look from the front of the remote control. DO NOT face toward a person or a
mirror.
Page 5
Table of Contents
Introduction............................................................................... E-1
Package Contents..................................................................... E-1
Optional Accessories ............................................................... E-1
Parts of the AVerMedia® AVerVision330 ................................E-2
Technical Specification ............................................................E-2
Hardware Installation and Setup .............................................E-3
Connection Ports...........................................................................................E-3
Setting the DIP Switch...................................................................................E-3
Connecting a VGA, Mac Display Monitor or LCD/DLP Projector..................E-3
Connecting a TV............................................................................................E-4
Connecting an IBM Compatible PC or Macintosh Computer........................E-4
Transferring the Pictures to a Computer via USB Connection......................E-4
Using AVerVision330 as USB PC Cam ........................................................E-5
Installing the LED Lamp ................................................................................E-5
Connecting the Power Adapter .....................................................................E-5
Installing the Optional Light Box....................................................................E-5
Connecting to a Microscope..........................................................................E-6
English Deutsch Français Italiano Español
Making the Adjustments ..........................................................E-6
Camera head.................................................................................................E-6
Mechanical Arm.............................................................................................E-6
LED Lamp .....................................................................................................E-6
LED Panel .....................................................................................................E-7
Infrared Sensor..............................................................................................E-7
Using the Infrared Remote Control .........................................E-7
Touch Button Control Panel ....................................................E-9
Timer Function........................................................................ E-10
To Set the Timer:.........................................................................................E-10
To View and Start the Timer Countdown: ...................................................E-10
OSD Navigation Tree .............................................................. E-11
Menu Functions ......................................................................E-12
Troubleshooting......................................................................E-14
Limited Warranty.....................................................................E-15
Page 6
Page 7
IInnttrroodduuccttiioonn
Thank you for purchasing the
AVerMedia® AVerVision330.
This document camera
displays any documents,
negatives, transparencies
and 3D objects onto a TV,
LCD or DLP projector making
product demonstration a
snap.
The AVerVision330’s
advanced features make it a
versatile and multifunctional
product. You can think of it as
a document camera, USB
card reader/writer, digital
camera and USB PC web
cam all rolled into a single
handy and compact device.
Bundled with it, is a remote
control, which has a laser
pointer, built right into it
making it easy for you to
highlight or point out key
areas in your presentation. All
these features make the
AVerVision330 an ideal
device for business,
academic, medical and the
scientific community.
PPaacckkaaggee CCoonntteennttss
Your AVerMedia® AVerVision330 package contains the following:
RCA Cable
S-Video Cable
DVI-RGB Cable
USB Cable
Power Adapter
AVerMedia
®
AVerVision330
Power Cord
* The power cord varies depending on the standard power
outlet of the country where it is sold.
English Deutsch Français Italiano Español
Installation CD
User Manual
Remote Control
(batteries included)
LED Lamp
OOppttiioonnaall AAcccceessssoorriiees
Light Box
* Required to view slide,
transparencies and film or to
display negative film as
positive image.
DVI/VGA Adapter
Carrying Case
s
Microscope Adapter
(28mm)
Mini Din-9pin to S-
Video/Composite/RS-232
Adapter
Microscope Adapter
(34mm)
E-1
Page 8
1. Camera Lens
2. Extendable Arm
3. Side Panel
4. Control Panel
5. LED
6. IR Remote Sensor
7. Back Panel
8. Power
9. TV/ RS-232 Port
10. USB Port
11. SD Card Slot
12. CF Card Slot
13. DIP switch
14. DC 6V (output)
15. Security Slot
16. DC 12V (input)
17. PC IN Port
18. DVI/VGA OUT Port
PPaarrttss ooff tthhee AAVVeerrMMeeddiiaa®® AAVVeerrVViissiioonn333300
The following diagrams indicate the names of each component, and port of the unit.
TTeecchhnniiccaall SSppeecciiffiiccaattiioonn
Image
Pick-up Device 1/3” progress scan CCD
Effective Pixels 790K 1024 (H) x 768 (V)
Frame Rate 20 fps
White Balance (RGB Output only) Auto/Manual
Exposure (RGB output only) Auto/ Manual/ Flicker / Night View
Image mode Text/ Graphics/ Microscope
Effect Color/ B/W / Negative/ Mirror/ Rotate
Analog RGB output XGA 75 Hz; SVGA 75 Hz
S-Video, C-Video Output NTSC/ PAL
Optics
Lens F1.8-2.7 AF
Shooting Area 380mm x 285mm (max.); 40mm x 30mm (min.)
Zooming Optical: 5x, Digital: 8x (Accelerated)
Focusing Auto/ Manual
Power Source 100-220V ~ 1.8A, 50-60 Hz
Consumption 15 Watts (lamp off); 30Watts (Lamp on)
Lighting
Lamp type LED lamp
Input
VGA Input 15-Pins D-sub (VGA)
RS232 9-Pins D-Sub Female
Output
VGA Output DVI to 15pin D-sub (VGA) Cable
DVI DVI-I Type Female
S-Video Mini-DIN Jack
Composite Video RCA Jack
USB USB Mini B Type
DC 6V Output Power Jack
Dimension
Operating 220mm x 140mm x 500mm
Folded 380mm x 170mm x 55mm
Weight 2 kg (about 4.4 lb) w/o Light Module
Card Supported
Secure Digital (SD) 16~512MB
Compact Flash (CF) 16~512MB
E-2
Page 9
HHaarrddwwaarree IInnssttaallllaattiioonn aanndd SSeettuupp
Connection Ports
The ports on the back and side panel of the AVerVision330 are for connecting the unit to a computer,
graphics display monitor or LCD/ DLP projector, TV and other devices. Illustrated below are the ports
that are located at the back and side panel of the AVerVision330 with their corresponding labels.
2
3
2
S
R
/
V
T
V
6
C
D
W
S
D
D
C
1
2
V
P
C
I
N
D
V
I
/
V
G
A
O
U
T
S
F
C
Port Description
1. Security Slot : Connect a Kensington compatible security lock to this slot.
2. DC 12 V (input) : Plug the power adapter in to this Port.
3. PC IN Port : Connect the AVerVision330 to the VGA output port of the computer. This enables
you to input computer video signal and pass it through to the DVI/VGA out port.
4. DVI/VGA OUT : Connect it to a VGA/ Mac monitor, LCD/DLP projector, or high-end projector with
5. CF Card Slot : Insert the CF card with the label facing up.
6. SD Card Slot : Insert the SD card with the label facing up.
7. DIP Switch : Allows you to set the DIP switch configuration settings.
8. USB Port : This port enables you to use AVerVision330 as a card reader/writer or PC web
9. DC 6V (output) : Plug the light module or the optional light box in to this port.
10. TV/RS-232 : Connect the Mini Din 9-Pin to S-Video/ Composite/ RS-232 Adapter to this port.
DVI interface to display your presentation.
cam.
The s-video and composite connectors enable you to output your video camera
or preview a picture from a memory card on your TV.
Note: The RS-232 adapter allows you to control the AVerVision330 using a
computer through an RS-232 connection. Refer to the RS-232 control instructions
on your CD for more information.
Setting the DIP Switch
The chart below tells you how to set the DIP switch. Turn the power off before changing the DIP switch
setting.
DIP Switch
UP NTSC RGB Default
DOWN PAL TV X
1
(TV SYSTEM)
(VIDEO OUTPUT)
2
3 - 4
(ENGINEERING PORT)
Connecting a VGA, Mac Display Monitor or LCD/DLP Projector
To display a presentation using a DVI/VGA or any graphics display monitor, set the DIP switch no. 2 to
the UP position.
English Deutsch Français Italiano Español
2
3
2
S
R
/
V
T
V
6
C
D
W
LCD Monitor
LCD/DLP
Projector
Mac Monitor
DVI-RGB Cable
(supplied)
MAC
Monitor Adapter
(optional)
DVI/VGA Adapter
(optional)
S
D
D
C
1
2
V
P
C
I
N
D
V
I
/
V
S
F
C
G
A
O
U
T
DVI/VGA Adapter
(optional)
SW
DIP SWITCH
VGA Monitor
E-3
DVI Cable
(not supplied)
LCD/DLP Projector
with DVI Interface
Page 10
Connecting a TV
To display a presentation on TV, set the DIP switch no. 1 to the TV system that you have (UP for NTSC
and DOWN for PAL) and DIP switch no. 2 to the DOWN position. If you are using a SCART RGB
monitor, set the DIP switch no. 1 to the DOWN position for PAL TV system. (The SCART RGB Cable is
provided as an optional accessory cable with the AVerVision330.)
IN
S-VIDEO
VIDEO
Television
SCART TV
D
C
1
2
V
P
C
I
N
SW
PAL TV SYSTEM
D
V
I
/
V
G
A
O
U
T
NTSC TV SYSTEM
2
3
2
S
R
/
V
T
V
6
C
D
W
S
D
S
F
C
SW
RS-232
Connector
S-Video
Connector
RCA
Connector
S-Video Cable
(supplied)
Video Cable
(supplied)
RCA to SCART
(optional)
Cable
To Computer COM PORT
Note: The RS-232 adapter allows you to control AVerVision330 using a computer through an RS-232
connection. Refer to the RS-232 control.
Connecting an IBM Compatible PC or Macintosh Computer
You can connect the AVerVision330 to an IBM compatible PC, Macintosh, or notebook (laptop)
computer. After physically connecting the unit to your PC, you can display an image on your computer
by pressing the PC button on the unit’s control panel or remote control.
IBM Compatible PC
OR
VGA Cable
(not supplied)
Plug to Display Card
Macintosh
Computer Adapter
(optional)
MAC
IInnsseerrttiinngg aanndd EEjjeeccttiinngg tthhee MMeemmoorryy CCaarrdd
Insert the card fully with the label facing up until it reaches the end. To remove, pull the card out. We
highly recommend formatting the memory card with the AVerVision330.
2
3
2
S
R
/
V
T
V
6
C
D
W
S
D
D
C
1
2
V
P
C
I
N
D
V
I
/
V
S
F
C
G
A
O
U
T
SD Card
(not supplied)
D
C
1
2
V
P
C
I
N
D
V
I
/
V
G
D
S
F
C
A
O
U
T
(not supplied)
W
S
CF Card
2
3
2
S
R
/
V
T
V
6
C
D
Transferring the Pictures to a Computer via USB Connection
USB Port
2
3
2
S
R
/
V
T
V
6
C
D
W
S
D
D
C
1
2
V
P
C
I
N
D
V
I
/
V
G
A
S
F
C
O
U
T
USB Cable
(supplied)
Laptop
Computer
E-4
Page 11
Computer Operating System Requirement
Windows 2000 SP4 and XP
SP1
No driver is required. Plug the AVerVision330 into an available
USB port. A new disk icon appears on your system.
Windows Me and 98/98SE You need to install the driver before connecting the unit to the
computer USB port. Insert the Driver CD in the CD-ROM drive.
The installation main screen will automatically appear and then
click Install. (For detailed mass storage driver installation
procedure, see the instruction provided in the CD and click
User Manual.)
Using AVerVision330 as USB PC Cam
For detailed PC Cam driver installation procedures, see the instruction provided in the CD and click
User Manual.
USB Port
English Deutsch Français Italiano Español
2
3
2
S
R
/
V
T
V
6
C
D
W
S
D
D
C
1
2
V
P
C
I
N
D
V
I
/
V
G
S
F
C
A
O
U
T
USB Cable
(supplied)
Computer
Installing the LED Lamp
Laptop
To ensure adequate lighting, focus the light towards the object to balance the distribution or range of
luminance for better image projection.
Connecting the Power Adapter
Use a standard 100V~240V AC power source.
Wall
Outlet
Power Cord
Power Adapter
W
S
D
D
C
1
2
V
P
C
I
N
D
V
S
F
C
I
/
V
G
A
O
U
T
Installing the Optional Light Box
Connecting an optional light box enables you to view x-rays, transparencies and negative slides.
Light Box
(optional)
Light Box
(optional)
D
C
1
2
V
P
C
I
N
D
V
I
/
V
G
A
O
T
U
R
N
N
O
U
T
2
3
2
S
R
/
V
T
V
6
C
D
W
S
D
S
F
C
PLUG ITHERE
E-5
2
3
2
S
R
/
V
T
V
6
C
D
Page 12
Connecting to a Microscope
Connecting the AVerVision330 to a Microscope enables you to examine microscopic objects on a big
screen without straining your eyes. To view microscopic images, you must set the unit to microscope
mode, and then adjust the microscope for a clearer image.
Connect and tighten
all three (3)
screws
Close-Up Lens
W
E
R
C
S
N
U
Microscope Adapter
(option)
W
E
R
C
S
Microscope
MMaakkiinngg tthhee AAddjjuussttmmeennttss
This section describes how your can adjust the AVerVision330 to meet your needs.
Camera head
The camera head can be rotated 125 degrees from left to right. As you rotate the camera head, the
camera adjusts the focus automatically.
15 degrees
90 degrees
Mechanical Arm
The mechanical arm is designed to move from
almost any angle. Follow the illustrated safety
procedure to adjust.
LED Lamp
Carefully adjust the light towards the object.
195 degrees
Extendable up
to 122mm
(4.8 in) long
120 degrees
60 degrees
45 degrees
45 degrees
E-6
Page 13
LED Panel
The chart below indicates the different status of AVerVision330.
Color Description
Green The unit is powered on.
Red The unit is in standby mode.
AVerMedia
Infrared Sensor
When using the remote control, aim it at the Infrared Sensor, which is located at the font panel of the
AVerVision330.
English Deutsch Français Italiano Español
UUssiinngg tthhee IInnffrraarreedd RReemmoottee CCoonnttrrooll
Use the AVerVision330 Remote Control to enhance your presentation, switch between (3) three
presentation modes and access additional features. To use the remote control, first insert the batteries
(2 size “AAA” batteries are provided) into the battery compartment at the back of the remote. Use the
figure and descriptions below to help you use the remote control.
Name Button Function
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
(10)
(11)
(12)
REVERSE
Laser emission part
(1)
(21)
(20)
(19)
(18)
(17)
ENTER
(16)
(15)
(14)
(13)
(1) POWER
(2) CAMERA
MODE
(3) PC MODE
(4) PLAYBACK
MODE
G2
Turn the unit on/off.
Switch to Camera mode and
display the image from the
AVerVision330’s built-in
CCD camera.
Switch to PC mode and
display the video signal from
the RGB input port.
Switch to Playback mode
and toggle to display 16thumbnail images or the
selected image from the
memory source.
To switch to other memory
source, AVerVision330 must be
in camera mode then press
MENU > ADVANCED >
MEMORY > TYPE > select the
source and press (►ENTER) >
press MENU to exit.
E-7
Page 14
Name Button Function
(5) EFFECTS
(6) TIMER
(7) REVERSE
(8 & 19)
PAGE UP/DOWN
(9) NIGHT VIEW
(10) FREEZE
(11) AUTO FOCUS
(12) FOCUS U / V
PG UP
REVERSE
PG DN
Convert and display the video in BW, Negative or
Color. (camera mode only)
Display, start and hide the on-screen display timer.
You can toggle to display or hide the remaining
time when the timer countdown has started. (See
Timer Function for more details)
Rotate the image by 180°. (camera mode only)
Display the previous and next set of 16-thumbnail
images.
Turn on/off Night View.
Use Night View when you are presenting in a low-
light condition. The captured image however,
appears in slow motion.
Toggle to pause or resume the camera.
Adjust the focus automatically.
Adjust the focus manually.
(13) ZOOM +/ -
The image may appear blurry when optically zooming the image in and out. After achieving
the desired magnification, the camera automatically adjusts the focus and the image will
(14) ZOOM RESET
(15) MENU
(16) ▲ ▼ ◄ (►
(17) LASER
become clear again.
ENTER)
- Zoom in and zoom out the picture digitally in
Playback mode.
- Zoom in and zoom out the image optically and
ENTER
digitally in Camera mode. When it reaches the
maximum optical zoom level of about 5 times,
you can still continue to digitally zoom in the
image up to 800%.
Return to normal view (1x).
Call up and exit the OSD main and sub-menu.
- Use ▲,▼, ◄ and (► ENTER) to make a
selection and adjustment. And use (► ENTER)
to enter sub-menu. (See Menu Functions, for
more details)
- Use ▲,▼, ◄ and (► ENTER) to make a
selection in 16-thumbnail images and press
to view the selected image.
Turn on the laser pointer.
(18) CAPTURE
(20) MIRROR
E-8
DO NOT look directly at the laser pointer
and avoid aiming the laser at any surface
that may reflect the beam (i.e., a mirror or
mirrored surface).
Photograph an image. The captured image is
automatically stored in the memory source at 1024
x 768 resolution.
Flip the image in Camera mode.
Page 15
Name Button Function
(21) DELETE
TToouucchh BBuuttttoonn CCoonnttrrooll PPaanneell
Remove the selected picture permanently in
Playback mode.
The touch button control panel located on the top side of AVerVision330 provides quick
access to commonly used functions.
(2)
(1)
(3)
(4)
(5)
(10)
(9)
(8)
(6)
(7)
Name Button Function
1
CAMERA MODE
2
PC MODE
3
PLAYBACK
MODE
4
FOCUS
U / V
Switch to Camera mode and display the image from the
AVerVision330’s built-in digital video camera.
Switch to PC mode and display the video signal coming from the
PC IN port.
Switches to Preview mode and displays 16-thumbnail pictures
from the memory card source. It only displays AVerVision330’s
photographed image or 1024 x 768 image resolutions.
Note: Use the JPEG Converter application to convert any JPEG
file to a format that is supported by the AVerVision330.
Press U or V to manually adjust the focus.
5
AUTO FOCUS
6
CAPTURE
7 & 9
MENU/
◄▲►▼
8
ZOOM +/ -
Automatically adjust the focus.
- In Camera mode, press to photograph an image. If there is an
available memory card in the slot, the captured image is
stored in the memory card automatically and saved in 1024 x
768 resolution.
- Press MENU to call the OSD menu and then use the ▲, ►,
▼ and ◄ to make a selection and adjustment. (Refer to the
section, Menu Functions, for more details.)
- In Preview mode, use the ▲, ►, ▼ and ◄ to make a
selection and then press CAP/FULL SCRN button.
In Preview mode, press “+” or “–“ to digitally zoom in and zoom
out the picture.
In Camera mode, press “+” or “–“ to optically zoom in and zoom
out the image. When the bar at the lower right corner of the
screen reaches the maximum level of magnification about 500%,
you can still continue to digitally zoom in the image up to 800%.
Note: The image may appear blurry when optically zooming the
image in and out. After achieving the desired magnification, the
camera adjusts the focus automatically and the image becomes
clear again. When you digitally zoom, the image appearance will
degrade.
English Deutsch Français Italiano Español
E-9
Page 16
TTiimmeerr FFuunnccttiioonn
The AVerVision330 enables you to control the pace of your presentation by displaying
the remaining time on the countdown screen. This merely serves as a reminder. When
the time is up, the timer blinks at the top right corner of the screen and the presentation
screen will not be affected in any way.
To Set the Timer:
1. Press MENU to view on screen function selections.
2. Press ▲or▼ buttons to select TIMER.
3. Press ►or◄ buttons to set a time value. You can set the
time value up to 120 minutes.
4. After setting the time value, press the MENU button to go
back to the main menu and exit.
To View and Start the Timer Countdown:
1. To display the previously set time value, press once.
The AVerVision330 automatically converts your settings to
“hours:minutes:seconds” format.
2. To start the countdown, press
3. Once the countdown timer starts, you can toggle the
countdown screen to display and hide it by pressing
again.
.
00:00:30
E-10
Page 17
OOSSDD NNaavviiggaattiioonn TTrreeee
RGB VIDEO OUTPUT OSD
BRIGHTNESS
-50 0 50
CONTRAST
MENU
BRIGHTNESS
CONTRAST
ZOOM
TIMER
MODE
EFFECT
DEFAULT
ADVANCED
MENU
BASIC
EXPOSURE
WHITE BALANCE
RESOLUTION
LANGUAGE
CARD
USB SELECT
-50 0 50
ZOOM
OPTICAL
DIGITAL
TIMER : MIN.
0 0 120
MODE
TEXT
GRAPHICS
MICROSCOPE
EFFECT
COLOR
B/W
NEGATIVE
MIRROR
REVERSE
DEFAULT
NO
YES
EXPOSURE
AUTO
MANUAL
FLICKER
NIGHT VIEW
WHITE BALANCE
AUTO
MANUAL
RESOLUTION
1024 X 768
800 X 600
640 X 480
LANGUAGE
ENGLISH
DEUTSCH
FRANCAIS
ITALIANO
ESPAÑOL
POLSKI
日本語
中文
CARD
TYPE
FORMAT
USB SELECT
PC CAMERA
MASS STORAGE
English Deutsch Français Italiano Español
MANUAL
-0 100 100
FLICKER
50 HZ
60 HZ
MANUAL
RED
BLUE
MEASURE
TYPE
SD
CF
FORMAT
NO
YES
RED
-0 91 511
BLUE
-0 66 511
E-11
Page 18
TV OUTPUT OSD DISPLAY
TIMER : MIN.
0 0 120
WHITE BALANCE
MENU
TIMER
WHITE BALANCE
EXPOSURE
CARD
DEFAULT
AUTO
MANUAL
EXPOSURE
AUTO
MANUAL
FLICKER
NIGHT VIEW
CARD
TYPE
FORMAT
DEFAULT
NO
YES
MANUAL
RED
BLUE
MEASURE
MANUAL
-0 100 100
FLICKER
50 HZ
60 HZ
TYPE
SD CARD
CF CARD
FORMAT
NO
YES
RED
-0 91 511
BLUE
-0 66 511
MMeennuu FFuunnccttiioonnss
The AVerVision330 provides MENU functions enabling you to fine-tune your screen display, set the
timer, select OSD language and more. Press the MENU button to call up and exit from the main
menu or sub-menu display. Then use ▲or▼ buttons to select the items in the menu list. Use
(►ENTER) button to enter sub-menu. To adjust the setting, press ◄or► buttons.
OSD Menu Description
BRIGHTNESS
-50 0 50
CONTRAST
-50 0 50
ZOOM
OPTICAL
DIGITAL
TIMER - MIN.
0 0 120
MODE
TEXT
GRAPHICS
MICROSCOPE
EFFECT
COLOR
B/W
NEGATIVE
MIRROR
REVERSE
BRIGHTNESS :
Press ►or◄ buttons to increase or decrease the brightness level
and improve the visibility of the image. You can adjust the
brightness level up to ±50.
CONTRAST :
Press ►or◄ buttons to emphasize or reduce the difference between
light and dark conditions. You can adjust the contrast level up to
±50.
ZOOM :
Use ▲or▼ buttons to select between Optical and Digital.
Optical zoom uses the physical lens inside the camera to achieve the
desired magnification, wherein the quality of the image is not affected.
When using digital zoom, it interpolates the pixels to enlarge the image,
which makes the image a bit blurry.
TIMER :
Press ►or◄ buttons to set a time value. You can set the time value up
to 120 minutes. (See Timer Function for more details)
MODE :
Use ▲or▼ buttons to select between text, graphics and microscope
image enhancement mode.
In text mode, the AVerVision330 corrects the intensity of the adjacent
pixel making it more uniform producing sharper and clearer images.
While in graphics mode, the AVerVision330 adjusts the gradient of the
adjacent pixel that appears to have a smooth image. Setting it to
microscope mode automatically fixes the optical zoom and displays the
microscope image more clearly.
EFFECT :
Use ▲or▼ buttons to display the image captured by the camera into
positive (true color), monochrome (black and white), negative,
mirrored image, or rotated image by 180º.
E-12
Page 19
W
OSD Menu Description
DEFAULT
NO
YES
DEFAULT :
Use ▲or▼ buttons to select YES to restore to original factory
default setting or NO to keep the current setting.
MENU
BRIGHTNESS
CONTRAST
ZOOM
TIMER
MODE
EFFECT
DEFAULT
ADVANCED
MENU
BASIC
EXPOSURE
WHITE BALANCE
RESOLUTION
LANGUAGE
CARD
USB SELECT
EXPOSURE
AUTO
MANUAL
FLICKER
NIGHT VIEW
MANUAL
0 50 100
FLICKER
50 Hz
60 Hz
HITE BALANCE
AUTO
MANUAL
MANUAL
RED
BLUE
MEASURE
RESOLUTION
1024 X 768
800 X 600
640 X 480
LANGUAGE
ENGLISH
DEUTSCH
FRANCAIS
ITALIANO
ESPAÑOL
ADVANCED :
Press ► to go to the Advanced menu.
BASIC :
Press ► to go to Basic menu.
EXPOSURE :
Use ▲or▼ buttons to select between Auto and Manual.
AVerVision330 allows you to automatically or manually adjust the
camera to determine how much light is required.
If you choose to manually adjust the exposure, press ►or◄ buttons to
adjust the exposure level.
If you are presenting in a low-light condition, enable Night View mode
from the remote control, then AVerVision330 automatically adjusts the
exposure to compensate the adverse condition but the captured image
will appear to be in slow motion.
FLICKER :
Use ▲or▼ buttons to select between 50Hz or 60Hz. Some display
devices cannot handle high refresh rates. The image will flicker a
couple of times as the output is switched to another refresh rate.
WHITE BALANCE :
Use ▲or▼ buttons to select between Auto and Manual.
AVerVision330 enables you to automatically or manually adjust the
camera to suit the lighting condition or color temperature. If you select
to manually adjust the white balance, you can adjust the Red, Blue or
use the system to measure the color temperature.
To obtain a more accurate color balance, place a sheet of white paper
under the camera. Select MEASURE then press (►ENTER) button to
calibrate the color temperature. Wait until a "MEASURE OK" appears
at the lower left corner of the presentation screen.
RESOLUTION :
Use ▲or▼ buttons to choose from 1024x768, 800x600 or 640x480
display resolution then press (►ENTER) to make the selection. This is
available only for RGI and DVI-I video output.
LANGUAGE :
Use ▲or▼ buttons to select from different languages then press
(►ENTER) to make the selection.
English Deutsch Français Italiano Español
POLSKI
日本語
中文
E-13
Page 20
OSD Menu Description
TYPE
CF
SD
FORMAT
NO
YES
USB SELECT
PC CAMERA
MASS STORAGE
TTrroouubblleesshhoooottiinng
This section provides useful tips describing how to solve common problems while using the
AVerVision330.
There is no picture on the presentation screen.
1. Check all the connectors again as shown in this manual.
2. Check your display output device remote control’s on/off switch.
3. Verify the setting of the display output device.
4. If you are to present using a notebook or computer, you may have to switch the source
to VGA.
I have set up the AVerVision330 and checked all the connections as specified in the
manual, but I can not get a picture on the preferred presentation screen.
- Once power is connected. You need to switch AVerVision330 "ON" from the unit to display the
picture on the presentation screen.
- The default camera display resolution setting is on 1024x768. If your output device does not
support this resolution you will not be able to see an image on your display device. You can
simply press the MENU and RIGHT or LEFT button to the increase or decrease the resolution
setting.
The picture on the presentation screen is distorted or the image is blurry.
TYPE :
Use ▲or▼ buttons to select the source on where to store or view the
image.
FORMAT :
Use ▲or▼ to select NO to exit or YES to format and delete all the data
in the memory source then press (►ENTER).
USB SELECT :
Use ▲or▼ buttons to select the USB function between PC Camera
and Mass Storage.
When AVerVision330 is connected to PC via USB connection,
AVerVision330 can function as PC Camera and Mass Storage device to
transfer the captured images to and from the memory source and
computer. With the bundled PC Camera application, you may use it to
record your presentation in AVI format or capture still image directly to
your PC’s hard disk.
g
1. Before doing any adjustments, reset all the picture attributes to the factory default
setting (Refer to the Menu Functions, for more details).
2. Each display device is slightly different from another. Use the Positioning and
Adjustment Control of AVerVision330 to adjust the picture.
3. Use the Brightness and Contrast menu functions to reduce the distortion.
There is no computer signal on presentation screen.
When you turn on the computer, it will auto-detect the type of monitor you have. During auto-detection,
there won't be any display on your presentation screen. To avoid this problem, connect your computer
and all the necessary cables to the AVerVision330 first before you power on your computer.
E-14
Page 21
LLiimmiitteedd WWaarrrraannttyy
For a period of time beginning on the date of purchase of the applicable product and extending as set
forth in Section 6 of this Limited Warranty (the “Warranty Period”), AVerMedia Technologies, Inc.
(“AVerMedia”) warrants that the applicable product (“Product”) substantially conforms to AVerMedia’s
documentation for the product and that its manufacture and components are free of defects in material
and workmanship under normal use. “You” as used in this agreement means you individually or the
business entity on whose behalf you use or install the product, as applicable. This limited warranty
extends only to You as the original purchaser. Except for the foregoing, the Product is provided “AS
IS.” In no event does AVerMedia warrant that You will be able to operate the Product without problems
or interruptions, or that the Product is suitable for your purposes. Your exclusive remedy and the entire
liability of AVerMedia under this paragraph shall be, at AVerMedia’s option, the repair or replacement of
the Product with the same or a comparable product. This warranty does not apply to (a) any Product
on which the serial number has been defaced, modified, or removed, or (b) cartons, cases, batteries,
cabinets, tapes, or accessories used with this product. This warranty does not apply to any Product
that has suffered damage, deterioration or malfunction due to (a) accident, abuse, misuse, neglect, fire,
water, lightning, or other acts of nature, commercial or industrial use, unauthorized product modification
or failure to follow instructions included with the Product, (b) misapplication of service by someone
other than the manufacturer’s representative, (c) any shipment damages (such claims must be made
with the carrier), or (d) any other causes that do not relate to a Product defect. The Warranty Period of
any repaired or replaced Product shall be the longer of (a) the original Warranty Period or (b) thirty (30)
days from the date of delivery of the repaired or replaced product.
Limitations of Warranty
AVerMedia makes no warranties to any third party. You are responsible for all claims, damages,
settlements, expenses, and attorneys’ fees with respect to claims made against You as a result of Your
use or misuse of the Product. This warranty applies only if the Product is installed, operated,
maintained, and used in accordance with AVerMedia specifications. Specifically, the warranties do not
extend to any failure caused by (i) accident, unusual physical, electrical, or electromagnetic stress,
neglect or misuse, (ii) fluctuations in electrical power beyond AVerMedia specifications, (iii) use of the
Product with any accessories or options not furnished by AVerMedia or its authorized agents, or (iv)
installation, alteration, or repair of the Product by anyone other than AVerMedia or its authorized agents.
English Deutsch Français Italiano Español
Disclaimer of Warranty
EXCEPT AS EXPRESSLY PROVIDED OTHERWISE HEREIN AND TO THE MAXIMUM EXTENT
PERMITTED BY APPLICABLE LAW, AVERMEDIA DISCLAIMS ALL OTHER WARRANTIES WITH
RESPECT TO THE PRODUCT, WHETHER EXPRESS, IMPLIED, STATUTORY OR OTHERWISE,
INCLUDING WITHOUT LIMITATION, SATISFACTORY QUALITY, COURSE OF DEALING, TRADE
USAGE OR PRACTICE OR THE IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A
PARTICULAR PURPOSE OR NONINFRINGEMENT OF THIRD PARTY RIGHTS.
Limitation of Liability
IN NO EVENT SHALL AVERMEDIA BE LIABLE FOR INDIRECT, INCIDENTAL, SPECIAL,
EXEMPLARY, PUNITIVE, OR CONSEQUENTIAL DAMAGES OF ANY NATURE INCLUDING, BUT
NOT LIMITED TO, LOSS OF PROFITS, DATA, REVENUE, PRODUCTION, OR USE, BUSINESS
INTERRUPTION, OR PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES ARISING OUT OF
OR IN CONNECTION WITH THIS LIMITED WARRANTY, OR THE USE OR PERFORMANCE OF
ANY PRODUCT, WHETHER BASED ON CONTRACT OR TORT, INCLUDING NEGLIGENCE, OR
ANY OTHER LEGAL THEORY, EVEN IF AVERMEDIA HAS ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES. AVERMEDIA’S TOTAL, AGGREGATE LIABILITY FOR DAMAGES OF ANY
NATURE, REGARDLESS OF FORM OF ACTION, SHALL IN NO EVENT EXCEED THE AMOUNT
PAID BY YOU TO AVERMEDIA FOR THE SPECIFIC PRODUCT UPON WHICH LIABILITY IS BASED.
Governing Law and Your Rights
This warranty gives You specific legal rights; You may also have other rights granted under state law.
These rights vary from state to state.
For warranty period, please refer to the warranty card.
E-15
Loading...