This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
NOTE- This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.
CAUTION ON MODIFICATIONS
To comply with the limits for the Class A digital device, pursuant to Part 15 of the FCC Rules,
this device must be installed in computer equipment certified to comply with the Class A
limits. All cables used to connect the computer and peripherals must be shielded and
grounded. Operation with non-certified computers or non-shielded cables may result in
interference to radio or television reception.
Changes and modifications not expressly approved by the manufacturer could void the
user’s authority to operate this equipment.
European Community Compliance Statement
Class A
This product is conformity with the protection requirements of EU Council
Directives 89/336/EEC amended by 92/31/EEC on the laws of the Member
States relating to electromagnetic compatibility.
Warning- This is a Class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures to correct
this interference.
English Español Português
DISCLAIMER
No warranty or representation, either expressed or implied, is made with respect to the
contents of this documentation, its quality, performance, merchantability, or fitness for a
particular purpose. Information presented in this documentation has been carefully checked
for reliability; however, no responsibility is assumed for inaccuracies. The information
contained in this documentation is subject to change without notice.
In no event will AVerMedia be liable for direct, indirect, special, incidental, or consequential
damages arising out of the use or inability to use this product or documentation, even if
advised of the possibility of such damages.
TRADEMARKS
AVerMedia is registered trademarks of AVerMedia TECHNOLOGIES, Inc. IBM PC is a
registered trademark of International Business Machines Corporation. Macintosh is a
registered trademark of Apple Computer, Inc. Microsoft is a registered trademark and
Windows is a trademark of Microsoft Corporation. All other products or corporate names
mentioned in this documentation are for identification and explanation purposes only, and
may be trademarks or registered trademarks of their respective owners.
may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into
any language in any form by any means without the written permission of AVerMedia
TECHNOLOGIES, Inc.
THE MARK OF CROSSED-OUT WHEELED BIN INDICATES THAT THIS
PRODUCT MUST NOT BE DISPOSED OF WITH YOUR OTHER
HOUSEHOLD WASTE. INSTEAD, YOU NEED TO DISPOSE OF THE
WASTE EQUIPMENT BY HANDING IT OVER TO A DESIGNATED
COLLECTION POINT FOR THE RECYCLING OF WASTE ELECTRICAL
AND ELECTRONIC EQUIPMENT. FOR MORE INFORMATION ABOUT
WHERE TO DROP OFF YOUR WASTE EQUIPMENT FOR
RECYCLING, PLEASE CONTACT YOUR HOUSEHOLD WASTE
DISPOSAL SERVICE OR THE SHOP WHERE YOU PURCHASED THE
PRODUCT.
Thank you for purchasing the AVerMedia® AVerVision130. This document
camera displays any documents, negatives, transparencies and 3D
objects onto a TV, LCD or DLP projector making presentations a snap.
The AVerVision130’s advanced features, including digital 4 times (400%)
zoom in, negative to positive, black and white to color picture, dynamic
image capture, image freezing function, make presentation become an
ease. While connected to a PC via USB cable, you can also capture and
save images and video clip to your presentation. Come with a full featured
control panel, AVerVision 130 is an ideal presentation tool for business,
academic, medical and the scientific community.
English Español Português
E-1
繁體中文
Page 6
PPaacckkaaggee CCoonntteennttss
AVerMedia® AVerVision130
Power Adapter
Power Cord
* The power cord will vary depending on the
standard power outlet of the country where it
is sold.
The ports on the back and side panel of the AVerVision130 enable you to connect
the unit to a computer, graphics display monitor or LCD / DLP projector, TV or other
device. Illustrated below are the ports that are located at the back and side panel of
the AVerVision130 with their corresponding labels.
Port Description
(1) Security Slot Use this port to connect a Kensington compatible security lock.
(2) DC 12V
(input)
(3) DC 6V
(output)
(4) USB1.1 Port This port enables you to use AVerVision130 as PC Camera, capture
(5) VIDEO Port The VIDEO Port enables you to output your camera or preview a
(6) S-VIDEO
Port
(7) VGA OUT
Port
(8) PC IN Port Use this port to connect the AVerVision130 to the VGA output port
Plug the power adapter into this port.
Plug the optional light box into this port.
the images or video to your PC.
picture from the built-in dynamic memory on your TV.
The S-VIDEO Port enables you to output your camera or preview a
picture from the built-in dynamic memory on your TV.
Use this port to connect to a VGA/ Mac monitor, LCD/DLP projector
for your camera, PC presentation, or playback a picture from built-in
dynamic memory.
of your computer. This enables you to input your computer video
You can connect the power adapter to a standard 100V~240V AC power source.
Wall
Outlet
Power Cord
Power Adapter
CCoonnnneeccttiinngg aa VVGGAA,, MMaacc DDiissppllaayy MMoonniittoorr oorr
LLCCDD//DDLLPP PPrroojjeeccttoorr
AVerVision130 enables you to display a presentation on a VGA /MAC display
monitor, or LCD/DLP projector with an outstanding video quality.
LCD Monito
VGA Cable
(not supplied)
LCD/DLP
Projector
Monitor
Adapter
(optional)
Mac
Monitor
E-6
Page 11
CCoonnnneeccttiinngg aa TTVV
To display a presentation on TV, connect AVerVision130 and TV by using the Video
Cable or S-Video cable, switch the output mode to TV system by pressing VGA/TV
button on the control panel. If you are using a SCART RGB monitor, connect it by
using the RCA to SCART Cable. (The SCART RGB Cable is provided as an optional
accessory cable with AVerVision130.)
You can connect the AVerVision130 to an IBM compatible PC, Macintosh, or
notebook (laptop) computer. After physically connecting the unit to your PC, you can
display an image from your computer by pressing the PC button on the unit’s control
panel.
utteerr
English Español Português
IBM Compatible PC
Macintosh
OR
Computer
Adapter
(optional)
VGA Cable
Plug to Display Card
E-7
繁體中文
Page 12
CCoonnnneeccttiinngg aa CCoommppuutteerr vviiaa UUSSBB ccoonnnneeccttiioonn
To access the software application as a PC Camera via the USB cable, just connect
the USB cable to a computer. (Refer to the section, using the AVerVision Application,
for more details.)
This section provides useful tips on how to adjust the AVerVision130 to meet your
needs.
CCaammeerraa HHeeaadd
The camera head can be rotated 135 degrees from left to right. You can also
manually adjust the focus from here to improve the quality of the pictures.
The flexible gooseneck and Mechanical arm design allows you to position the
camera head from any angle.
90 degrees
45 degrees
45 degrees
90 degrees
E-10
Page 15
t
t
LLEEDD LLiigghhtt MMoodduullee
The LED light module provides white light and it is best use when presenting in low
lightning condition.
AAnnttii--ggllaarree SShheeeett
The anti-glare sheet is a special coated film that helps eliminate any glare you may
encounter when you are displaying very shiny object or glossy surfaces such as
magazines, pictures, etc. Simply place the anti-glare sheet on top of the shiny
document to reduce reflected light.
Turn on LED LightTurn on LED LightTurn off LED Ligh
Turn off LED Ligh
English Español Português
繁體中文
E-11
Page 16
TToouucchh BBuuttttoonn CCoonnttrrooll PPaanneell
The touch button control panel located on the top side of the AVerVision130 provides
quick access to commonly used functions.
(2)
(3)
(4)
(5)
(6)
AVerVision130AVerVision130
Function Description
1
CAMERA
MODE
2
PC MODE
3
PLAYBACK
MODE
4
VGA/TV
5
EFFECT
Switches to Camera mode and displays the image from the
AVerVision130’s built-in digital video camera.
Switches to PC mode and displays the video signal coming from
the PC IN port.
Switches to PLAYBACK mode and displays 4-thumbnail images
captured in AVerVision130’s built-in memory.
Switches between VGA (VGA Out) or TV (Composite
Video/S-Video) output.
In Camera mode, press to convert and view the video in Black and
White, Negative or Color.
CAPTURE
(1)
(10)
(9)
(8)
(7)
6
FREEZE
7
CAP/DEL
Press this button to hold the image picked up by the camera and
to release the image that has been retained.
In Camera mode, press to capture an image. The captured image
is automatically stored in the built-in dynamic memory at 1024 x
768 resolution. AVerVision130 could save up to 4 frames.
In Playback Mode, press this button to delete the saved frame.
E-12
Page 17
FunctionDescription
- Press MENU to call the OSD menu and then use the ▲, ►, ▼
and ◄ around the menu button to make a selection and
adjustment.
8 & 10
MENU/
◄▲►▼
9
ZOOM +/ -
- In playback mode, use the ▲, ►, ▼ and ◄ to make a selection
and then press PLAYBACK to display the image in full-size. You
may also use PLAYBACK button to revert back to display
4-thumbnail pictures.
- In zoom-in mode, use the ▲, ►, ▼ and ◄ to pan up , down , left
and right
Press “+” or “–” to digitally zoom in and zoom out the picture up to
400%.
English Español Português
LLEEDD PPaanneell
The LED on the front panel of AVerVision130 indicates the status of the unit.
Green The unit is operated with VGA output.
Orange The unit is operated with TV output
Red The unit is in standby mode.
Use the AVerVision PC Camera applications provided to control the AVerVision130
to save any captured images or video clips to your PC, or send them via emails.
Note:
When a USB cable is connected between the document camera and the PC, the
document camera features are controlled by the application software directly, but
selective features can still work with control panel on the camera and remote control,
for details of selective features, please refer to the FAQ on our website.
Color Description
IInnssttaalllliinngg tthhee SSooffttwwaarree
Minimum System Requirements
Pentium
Windows2000 Professional with Service Pack 4, Windows XP Professional
Service Pack 2 or Home, or Windows XP Tablet PC
128 MB of RAM (256MB recommended)
60 MB of available hard-disk space
To install PC Camera Applications:
1. Insert your Software CD into your CD-ROM drive, and click on "PC Camera
®
-class processor
Applications” and follow the instructions.
繁體中文
E-13
Page 18
2. Click “Finish” to complete installation.
3. After the installation, connect the USB cable between the AVervVsion130 and
your PC. Open the applications by clicking “VisionAP” icon on your desktop.
6
7
8 Display the image from AVerVision’s camera or from the PC
9
10
11
CC.. SSnnaappSShhoott//VViiddeeoo
Function Description
12
13
14
15
16
17
Digital Zoom and Pan Control
Return to normal view (1X )
Convert the image to Negative
Convert the image to Black and White
Back to the original image
Restore to original factory setting
Select between text and graphic image enhancement mode
IN port
Freeze image
Adjust White Balance
Adjust Exposure
Control the video display by controlling bar
Play and control the video display
Record the video and save it into PC
Capture a single picture and save it into PC
Retrieve saved picture or video clips
Setup for the picture snapshot or video recording.
(10)
(11)
(14)
(15)
(16)
(17)
English Español Português
繁體中文
E-15
Page 20
OOSSDD NNaavviiggaattiioonn TTrreeee
EXPOSURE
AUTO
MANUAL
FLICKER
WHITE BALANCE
AUTO
MANUAL
MENU
EXPOSURE
WHITE BALANCE
MODE
EFFECT
RESOLUTION
LANGUAGE
DEFAULT
MODE
TEXT
GRAPHICS
EFFECT
COLOR
B/W
NEGATIVE
RESOLUTION
1024 X 768
800 X 600
640 X 480
LANGUAGE
ENGLISH
ESPAÑOL
PORTUGUÊS
日本語
繁體中文
MANUAL
0 25 45
FLICKER
50Hz
60Hz
MANUAL
RED
BLUE
MEASURE
RED
0 91 255
BLUE
0 66 255
DEFAULT
NO
YES
E-16
Page 21
MMeennuu FFuunnccttiioonnss
The MENU functions of AVerVision130 enhance fine-tuning your screen display, set
the timer, select OSD language and more. Press the MENU button to call up and
exit from the main menu or sub-menu display. Then use ▲or▼ buttons to select
the items in the menu list. Use ► button to enter sub-menu. To adjust the
setting, press ◄or► buttons.
Main Menu Sub-Menu OSD Description
EXPOSURE
WHITE
BALANCE
MODE
EXPOSURE
AUTO
MANUAL
FLICKER
MANUAL
025 45
FLICKER
50 Hz
60 Hz
WHITE BALANCE
AUTO
MANUAL
MANUAL
RED
BLUE
MEASURE
MODE
TEXT
GRAPHICS
Use ▲or▼ buttons to select between Auto
and Manual.
AVerVision130 allows you to automatically
or manually adjust the camera to determine
how much light is required.
If you choose to manually adjust the
exposure, press ►or◄ buttons to adjust
the exposure level.
Use ▲or▼ buttons to select between 50Hz
or 60Hz. Some display devices cannot
handle high refresh rates. The image will
flicker a couple of times as the output is
switched to another refresh rate.
Use ▲or▼ buttons to select between Auto
and Manual.
AVerVision130 enables you to automatically
or manually adjust the camera to suit the
lighting condition or color temperature. If
you select to manually adjust the white
balance, you can adjust the Red, Blue or
use the system to measure the color
temperature.
To obtain a more accurate color balance,
place a sheet of white paper under the
camera. Select MEASURE then press ►
button to calibrate the color temperature.
Wait until a "MEASURE OK" appears at the
lower right corner of the presentation
screen.
Use ▲or▼ buttons to select between text
and graphics image enhancement mode.
In text mode, the AVerVision130 corrects
the intensity of the adjacent pixel making it
more uniform producing sharper and
clearer images. While in graphics mode,
the AVerVision130 adjusts the gradient of
the adjacent pixel that appears to have a
smooth image.
English Español Português
繁體中文
E-17
Page 22
Main Menu Sub-Menu OSD Description
EFFECT
EFFECT
COLOR
B/W
NEGATIVE
Use ▲or▼ buttons to display the image
captured by the camera into negative,
positive (true color), or monochrome (black
and white) the image.
RESOLUTION
LANGUAGE
DEFAULT
RESOLUTION
x 768
1024
800x 600
640
ENGLISH
ESPAÑOL
PORTUGUÊS
日本語
繁體中文
NO
YES
480
x
LANGUAGE
DEFAULT
TTrroouubblleesshhoooottiinngg
Use ▲or▼ buttons to choose from
1024x768, 800x600 or 640x480 display
resolution then press ► to make the
selection.
This selection will not be found in TV output
(Composite/S-Video)
Use ▲or▼ buttons to select from nine
different languages then press ► to make
the selection.
Use ▲or▼ buttons to select YES to restore
to original factory default setting or NO to
exit then press ► to make the selection.
This section provides many useful tips on how to solve common problems
while using the AVerVision130.
There is no picture on the presentation screen.
1. Check all the connectors again as shown in this manual.
2. Check the on/off switch of the display output device.
3. Verify the setting of the display output device.
4. If you are presenting from a notebook or computer through the display
output device, please check and switch the document camera source to
PC Mode.
I have set up the AVerVision130 and checked all the connections as
specified in the manual, but I cannot get a picture on the preferred
presentation screen.
1. Once the power cords are connected, the LED light turns RED as
standby mode. Simply switch the AVerVision130 “ON" by pressing the
on/off switch until the LED light is blanking and turns GREEN.
2. The default camera display resolution setting is on 1024x768. If your
output device does not support this resolution; no image can be
projected. Simply press the MENU and RIGHT or LEFT button to the
increase or decrease the resolution setting.
E-18
Page 23
3. If your display output device is TV or any analog device, please click on
the VGA/TV button to switch output mode.
The picture on the presentation screen is distorted or the image is
blurry.
1. Reset all changed settings, if any, to the original manufacturer default
setting (Refer to the Menu Functions for more details and steps).
2. Use the Brightness and Contrast menu functions to reduce the
distortion if applicable.
3. If you discover that the image is blurry or out of focus, adjust the focus
ring on the camera head.
There is no computer signal on presentation screen.
1. Check all the cable connections among the display device,
AVerVision130 and your PC.
2. Connect your PC to the AVerVision130 first before you power on your
computer.
I plug in the power of AVerVision130, but still couldn't see anything.
It will take 20~30 seconds for warming up AVerVision130.
English Español Português
LLiimmiitteedd WWaarrrraannttyy
For a period of time beginning on the date of purchase of the applicable product and extending
as set forth in Section 6 of this Limited Warranty (the “Warranty Period”), AVerMedia
Technologies, Inc. (“AVerMedia”) warrants that the applicable product (“Product”) substantially
conforms to AVerMedia’s documentation for the product and that its manufacture and
components are free of defects in material and workmanship under normal use. “You” as
used in this agreement means you individually or the business entity on whose behalf you use
or install the product, as applicable. This limited warranty extends only to You as the original
purchaser. Except for the foregoing, the Product is provided “AS IS.” In no event does
AVerMedia warrant that You will be able to operate the Product without problems or
interruptions, or that the Product is suitable for your purposes. Your exclusive remedy and the
entire liability of AVerMedia under this paragraph shall be, at AVerMedia’s option, the repair or
replacement of the Product with the same or a comparable product. This warranty does not
apply to (a) any Product on which the serial number has been defaced, modified, or removed,
or (b) cartons, cases, batteries, cabinets, tapes, or accessories used with this product. This
warranty does not apply to any Product that has suffered damage, deterioration or malfunction
due to (a) accident, abuse, misuse, neglect, fire, water, lightning, or other acts of nature,
commercial or industrial use, unauthorized product modification or failure to follow instructions
included with the Product, (b) misapplication of service by someone other than the
manufacturer’s representative, (c) any shipment damages (such claims must be made with the
carrier), or (d) any other causes that do not relate to a Product defect. The Warranty Period of
any repaired or replaced Product shall be the longer of (a) the original Warranty Period or (b)
thirty (30) days from the date of delivery of the repaired or replaced product.
E-19
繁體中文
Page 24
Limitations of Warranty
AVerMedia makes no warranties to any third party. You are responsible for all claims,
damages, settlements, expenses, and attorneys’ fees with respect to claims made against You
as a result of Your use or misuse of the Product. This warranty applies only if the Product is
installed, operated, maintained, and used in accordance with AVerMedia specifications.
Specifically, the warranties do not extend to any failure caused by (i) accident, unusual physical,
electrical, or electromagnetic stress, neglect or misuse, (ii) fluctuations in electrical power
beyond AVerMedia specifications, (iii) use of the Product with any accessories or options not
furnished by AVerMedia or its authorized agents, or (iv) installation, alteration, or repair of the
Product by anyone other than AVerMedia or its authorized agents.
Disclaimer of Warranty
EXCEPT AS EXPRESSLY PROVIDED OTHERWISE HEREIN AND TO THE MAXIMUM
EXTENT PERMITTED BY APPLICABLE LAW, AVERMEDIA DISCLAIMS ALL OTHER
WARRANTIES WITH RESPECT TO THE PRODUCT, WHETHER EXPRESS, IMPLIED,
STATUTORY OR OTHERWISE, INCLUDING WITHOUT LIMITATION, SATISFACTORY
QUALITY, COURSE OF DEALING, TRADE USAGE OR PRACTICE OR THE IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR
NONINFRINGEMENT OF THIRD PARTY RIGHTS.
Limitation of Liability
IN NO EVENT SHALL AVERMEDIA BE LIABLE FOR INDIRECT, INCIDENTAL, SPECIAL,
EXEMPLARY, PUNITIVE, OR CONSEQUENTIAL DAMAGES OF ANY NATURE INCLUDING,
BUT NOT LIMITED TO, LOSS OF PROFITS, DATA, REVENUE, PRODUCTION, OR USE,
BUSINESS INTERRUPTION, OR PROCUREMENT OF SUBSTITUTE GOODS OR
SERVICES ARISING OUT OF OR IN CONNECTION WITH THIS LIMITED WARRANTY, OR
THE USE OR PERFORMANCE OF ANY PRODUCT, WHETHER BASED ON CONTRACT OR
TORT, INCLUDING NEGLIGENCE, OR ANY OTHER LEGAL THEORY, EVEN IF AVERMEDIA
HAS ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. AVERMEDIA’S TOTAL,
AGGREGATE LIABILITY FOR DAMAGES OF ANY NATURE, REGARDLESS OF FORM OF
ACTION, SHALL IN NO EVENT EXCEED THE AMOUNT PAID BY YOU TO AVERMEDIA FOR
THE SPECIFIC PRODUCT UPON WHICH LIABILITY IS BASED.
Governing Law and Your Rights
This warranty gives You specific legal rights; You may also have other rights granted under
state law. These rights vary from state to state.
For warranty period, please refer to the warranty card.
E-20
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.