AVer FV1306 User Manual

AVer FV1306

User Manual

................................

................................

................................

................................

................................

................................

................................

................................

................................

................................

................................

...............................

................................

................................

................................

................................

................................

................................

................................

................................

................................

................................

................................

................................

Table of Contents

PREFACE ................................................................

PRODUCT SPECIFICATIONS ................................

PACKAGE CONTENTS ................................................................

PRODUCT INSTALLATION ................................................................

MONITOR SETTING ................................................................

HARDWARE INSTALLATION AND I/O PIN ASSIGNMENT

POWER OVER ETHERNET (POE) ................................

IP ASSIGNMENT ................................................................

FINDING IP CAMERA BY USING “NXU LITE RECORDING SOFTWARE”
FINDING IP CAMERA BY USING “AVER IPCAM UTILITY”

USING NON-DHCP SERVER/ROUTER NETWORK ................................

INSTALL ACTIVEX CONTROL ................................................................

USING THE IP CAMERA BROWSER INTERFACE

PREVIEW ................................................................

SYSTEM > GENERAL ................................................................

............................ 1

............................. 1

....... 4

. 5

............. 5

.............................. 6

.......................... 9

................ 10

........ 10

......................... 14

16
18

.......................... 20

......................... 20

......... 23

SYSTEM > GENERAL > MAINTENANCE ................................

To Upgrade the IP Camera Firmware ................................

SYSTEM > GENERAL > DATE & TIME ................................

SYSTEM > USER MANAGEMENT ................................

SYSTEM > USER MANAGEMENT ................................

SYSTEM > NETWORK SETTING > SETTING ................................

SYSTEM > NETWORK SETTING > SEVER ................................

SYSTEM > NETWORK SETTING > DDNS ................................

SYSTEM > NETWORK SETTING > OTHER 1 ................................

................. 23

....... 24

................... 25

......................... 26

......................... 26

........... 28

............. 29

............. 30

.......... 32

SYSTEM > NETWORK SETTING > OTHER 2 .......................................................................... 34

SYSTEM > NETWORK SETTING > IPV6 ................................................................................ 38

BESIDE IPV4, THERE IS IPV6 FOR USERS TO SET UP IP ADDRESS. .......................................... 38

SYSTEM > ADVANCE > HTTPS .......................................................................................... 39

SYSTEM > ADVANCE > SNMP ........................................................................................... 41

SYSTEM > ADVANCE > ACCESS LIST ................................................................................... 43

SYSTEM > ADVANCE > QOS/DSCP ................................................................................... 44

SYSTEM > IMAGE .............................................................................................................. 45

SYSTEM > IMAGE> OSD ................................................................................................... 45

SYSTEM > IMAGE > PREFERENCE ....................................................................................... 46

SYSTEM > IMAGE> ADVANCED ........................................................................................... 47

SYSTEM > IMAGE> PRIVACY MASK ..................................................................................... 49

SYSTEM > VIDEO STREAM > GENERAL ............................................................................... 50

SYSTEM > VIDEO STREAM > STREAM1 ............................................................................... 51

SYSTEM > VIDEO STREAM > STREAM2 ............................................................................... 53

SYSTEM > VIDEO STREAM > STREAM3 ............................................................................... 55

SYSTEM > AUDIO .............................................................................................................. 56

SYSTEM > SD CARD ......................................................................................................... 57

EVENT > ARRANGEMENT > MOTION .................................................................................... 58

EVENT > ARRANGEMENT > PREFERENCE ............................................................................ 59

EVENT > SCHEDULE ......................................................................................................... 60

EVENT > DI/DO ............................................................................................................... 61

STATUS INFORMATION ....................................................................................................... 62

NETWORK CONFIGURATION .......................................................................................... 63

FACTORY DEFAULT ......................................................................................................... 65

TROUBLESHOOTING ....................................................................................................... 66

APPENDIX ......................................................................................................................... 67

................................

................................

................................

................................

COPYRIGHT ................................................................

NOTICE ................................................................

WARNING ................................................................

GOVERNING LAW AND YOUR RIGHTS ................................

...................... 68

.............................. 68

.......................... 68

.......... 70

elay out

ENGLISH

Preface

The FV1306 is an H.264, 720p super min vandal proof dome camera designed ultra-discreet,
recessed-mount and super mini dimension (Φ:80mm) for indoor and outdoor use. FV1306 is
specifically developed for, offering discreet video surveillance solutions, ideal for ATM, banks, retail
stores, boutiques and elevators. Rated to IP66, FV1306 gives you the flexibility of a camera that can
withstand both dust and driving rain.

Product Specifications



1.3M-pixel, vandal proof dome



HD Definition (720p) 30fps support



Digital Wide Dynamic Range



Power over Ethernet (PoE)



H.264/MJPEG/MPEG-4 compression formats



microSD/SDHC card backup (SD card is not included)



2-way audio



Adjustable shutter speed



Support iPhone/ iPAD/ Android phone and PAD



Free bundled 32-CH AVer NXU Lite recording software

Specifications

Hardware

CPU ARM 9, 32-bit RISC
RAM 128MB
Flash 16M
Image sensor 1/4” CMOS (1.3 Megapixel)
Lens Type 4.2mm@F1.6, Megapixel fixed lens
Shutter time 1/5~1/10,000
I/O 1 Sensor in /1 R
MIC in 1
Audio Out 1

Power Over Ethernet Yes
Power Consumption

DC12V：2.04W
PoE：2.88W

1

Hardware

2-Axis Gimbal Adjustments Angle

Dimensions
Operation Temperature 0°C ~ 45°C
Weight 350g

Network

Ethernet 10/100 Base-T
Network Protocol

System

Video Resolution

Video Adjust

Triple Streaming Yes
Image snapshot Yes

Pan: 360∘
Tilt: 20∘~ 90∘

Φ80 x 67 (mm)

IPv6, IPv4, HTTP, HTTPS, SNMP, QoS/DSCP, Access
list, RTSP, TCP/IP, UDP, SMTP, FTP, PPPoE, DHCP,
DDNS, NTP, UPnP, 3GPP (video only), SAMBA,
Bonjour

1280x1024@20fps, 1280x800@30fps,
1280x720@30fps ,640x480@30fps, 320x240@30fps,

176x144@30fps
Brightness, Contrast, Sharpness, D-WDR, Shutter
Speed, Sense-Up, AGC..etc.

Full screen monitoring Yes
Privacy Mask Yes, 3 different areas

Compression format H.264/ JPEG/ MPEG-4
Video bitrate adjust CBR, VBR
Motion Detection Yes, 3 different areas
Triggered action Mail, FTP, Save to microSD/SDHC card, Relay,

SAMBA

Pre/ Post alarm Yes (Pre: 5 secs/ Post: 5 secs)

2

ENGLISH

System

Security

Firmware upgrade HTTP mode, can be upgraded remotely
Simultaneous connection Up to 10
Audio Yes, 2-way (mono)

MicroSD/SDHC card management

Recording trigger Motion Detection, IP Check, Network Status (wired

Video format AVI, JPEG
Video playback Yes
Delete files Yes

Web browsing requirement

OS Windows® XP (32-bit), 7 (32/64-bit)

Hardware Suggested

Mobil support iOS 5 or above, Android 1.6 or above.

Password protection, IP address filtering, HTTPS
encrypted data transmission, QoS/DSCP

Connection only), Schedule,

Microsoft® IE 6.0 or above (32-bit only)

Notes: Please enable “Compatibility View” while using
IE 10 or above.

Intel® Dual Core 2.53GHz, RAM: 1024MB, Graphics
Card: 128MB

*SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.

3

0.5

Quick Guide

NVR

Package contents

Item Descriptions

1. FV1306

2. Accessory pack

3. Conversion ring

4. Power Adaptor(DC 12V/

5. CD (User’s Manual,
software are included)

A) (Optional)

, and

4

ENGLISH

Product Installation

Monitor Setting

1. Right-click on the desktop. Select “ Properties”

2. Change “Color quality” to “Highest (32-bit)”.

5

Hardware Installation and I/O Pin Assignment

1. Set the camera
Locate cable from bottom

a. Use three screws to lock the base of camera on the ceiling or the wall.
b. Put back the cover, and turn it tightly to get waterproof.

Installation tip: Please don’t open the top cover for too long if you install the camera under a high
humidity environment.

6

Locate cable from side

a. Open the conversion ring package in accessory. It includes a conversion ring and two

set of screws.
b. Use three screws to lock the conversion ring on the ceiling or the wall.
c. Use three screws to combine the base of camera with the conversion ring. The cable

can pass through the hole on the side of conversion ring.
d. Put back the cover, and turn it tightly to get waterproof.

ENGLISH

7

2. When removing the dome cover, you can see the Micro SD card slot and the reset button.

3. I/O Interface

I/O Connection

a. Please connect the GND & DO pin to the external relay (buzzer) device.
b. Please connect the GND & DI pin to the external trigger device.

8

ENGLISH

Power Over Ethernet (PoE)

Set up the IP camera through Power over Ethernet (PoE). PoE is a technology that integrates power
into a standard LAN infrastructure. It enables power to be provided to the network device, such as an
IP camera, using the same cable as that used for network connection. It eliminates the need for power
outlets at the camera locations.

[Note] 802.3at, 30W PoE Switch is recommended.

Ethernet

PoE IP Camera

PoE Switch

Ethernet Cable

Ethernet Cable

PoE IP Camera

9

IP Assignment

There are two ways to find IP Camera:

− Finding IP Camera by using “NXU Lite recording software”

− Finding IP Camera by using “AVer IPCam Utility”

Finding IP Camera by using “NXU Lite recording software”

1. The NXU Lite software is in the attached software CD. Before launching it, please install the
software first. During the installing process, users will be required to input a User name and
Password for login NXU Lite system. Users can define the User name and Password as wishes.
Please refer to NXU Lite user manual for detailed installation instruction.

2. To run the application, double-click on your PC desktop or click Start > Programs > DVR >
NXU Lite. For security purpose, some of the features would require you to enter User name and
Password before it can be accessed. When the Authorization dialog box appears, key in your User
ID and Password. (If this is the first time, enter the one you have registered when installing the
software.

Click it to call out virtual
keyboard.

10

3. Click “Setup” button.

4. Click “Add IPCam” button.

ENGLISH

11

5. Select “IP Camera” item.

6. Key in IP Camera’s ID and Password (default is admin/admin) and click “Auto Search” to find
camera.

12

7. In Search Result window, click it the IP camera model that user has purchased (Please ignore
ONVIF connection item); the camera is in red text that is configurable. User can double-click on
the camera is in red text and configure the IP camera’s setting; even the IP camera is not in the
same IP segment. Press “OK” to back to previous screen and press ”Connect” to start live view.

Double-click the IP camera
model that user has
purchased (ex: FV1306).

Please ignore ONVIF
protocol selection; NXU Lite
doesn’t support ONVIF
connection.

ENGLISH

13

Finding IP Camera by using “AVer IPCam Utility”

1. Use the software, “AVer IPCam Utility” to assign the IP address of the IP camera. The software is
in the attached software CD.

2. Run the IPCam Utility

3. Select the proper network adapter and click [Search] to begin searching.

4. Select and double click the IP camera you want to access. If you want to change the setting of the
selected IP camera, enter the user ID, correct password, and change the settings and then click
Apply button. This will change the setting and rescan the network again.

14

5. The IE browser will open and direct you to IP camera login page. This requires IPViewer.ocx to run.
If the IE ActiveX warning message appears, click to allow running the add-on.

[Note]

 The default IP address is: 192.168.1.168
 The default ID and Password are both ”admin”.
 It is not allowed to enter device name in Chinese and any other special characters (' " \ & ^).
 Gateway number can’t be “0”.
 IP camera device name should be less than 30 digits

ENGLISH

15

Using NON-DHCP Server/Router Network

In Non-DHCP server/router network, the static IP address must be assigned to the device each time
when adding another IP camera to the network; the default IP address of the current one must be
changed to avoid conflict.

Please make sure the Subnet of the PC’s IP address and the IP camera’s IP address are the same.

[Example]

The same Subnet:

IP camera IP address: 192.168.1.168
PC IP address: 192.168.1.100

Different Subnets:

IP camera IP address: 192.168.1.168
PC IP address: 192.168.2.100

To Change PC IP Address:

Control PanelNetwork Connections  Local Area Connection Properties  Internet
Protocol (TCP/IP)  Properties
Please make sure your IP camera and PC have the same Subnet. If not, please change IP
camera subnet or PC IP subnet accordingly.

PC’s IP address:

16

IP camera IP addresses:

A quick way to access remote monitoring is to double-click on a selected IP camera in “Camera Name
list” in AVer IPCam Utility. Then, the IE browser will open and connect to IP camera.

Then, please key in the default “ID” and “Password”, both of which are “admin”.

ENGLISH

Notes: Please enable “Compatibility View” while using IE 10 or above.

17

Install ActiveX Control

The first time you attempt to view the camera video via Internet Explorer, it will ask you to install the
ActiveX component.

If the installation fails, please check the security settings for the Internet Explorer browser.

1. IE  Tools  Internet Options…  Security Tab  Custom Level…  Security Settings 
Download unsigned ActiveX controls Select “Enable” or Prompt.

2. IE  Tools  Internet Options…  Security Tab  Custom Level… Initialize and script ActiveX
controls not marked as safe  Select “Enable” or Prompt.

1 2

3 4

18

ENGLISH

5

When the following dialogue box appears, click “Yes”.

19

Using the IP Camera Browser Interface

The admin have the full access to the IP camera browser interface. The menu on the left, you can
expand and navigate to access all the features.

Preview

Launch the Internet Explorer browser, type the IP address of the IP camera in the address field. It will
show the following dialogue box. Key-in the”ID” and “Password”. The default”ID” and “Password” are
both “admin”.

Once connected to the IP camera, the following program interface will appear.

Name Function

(1) System/Event/Status

Information

Set up IP camera’s configuration.

20

Name Function

(2) Login IP
(3) Bandwidth
(4) FW Version
(5) Logout
(6) Zoom control

(7) Capture

ENGLISH

Show PC’s IP address
Show current IP camera’s transmitting bandwidth
Show IP camera’s current firmware version

Exit the application

Reset zoom level.
Increase zoom level.
Decrease zoom level.

Use the scroll bar to zoom in or zoom out the

video screen

Capture and save the image on the screen in *.bmp format

(8) Record

(9) 2-way Talk

(10) Speaker

(11) Language
(12) Video screen

(13) Stream

Start/stop audio and video recording. The recorded video will

be saved in *.avi format.

Click the Microphone button to talk to IP camera side from

user site. Click this button again to mute this function.

Turn on the PC’s speaker so that PC side can hear sound

from IP camera side. Click this button again to mute this function.

Use the scroll bar to adjust the speaker volume.

It shows the current speaker volume’s value.

Select the browser interface language.
Change the video screen display.

Display the actual video pixel size
Display the video screen in compact size.

Display the video in full screen mode. Press ESC to exit full
screen mode.

Switch to view the video stream type. The IP camera can send
multiple video streams of up to 3 types. To change the video stream
setting, go to System > Video Stream.
[Notes]When streaming 2 setting in”Video Setting” is closed, there
won’t have other stream option

21

Name Function

(14) Direction Controller

Move the position of the view point while in zoom mode. User has
to zoom in first.

22

ENGLISH

System > General

I

n this section, only admin level is authorized to configure the IP camera system maintenance and the

date and time settings.

System > General > Maintenance

In the Maintenance tab, the administrator can check the system event log, upgrade the system
firmware, reset the configuration settings without having to change the user management and network
settings, reboot, and restore all back to factory default settings.

Name Function

(1) Export Settings

(2) Reboot
(3) Factory default

Upload to save all the configuration settings from the IP camera to
computer hard disk.

Turn the IP camera off and on again.
Set all the configuration settings back to default except the user

management and network settings.

23

Name Function

(4) Firmware Upgrade

Upgrade the firmware to the latest version.

To Upgrade the IP Camera Firmware

1. Download the file from
our website and save it
in your computer hard
disk.

2. Click Browse. Locate
and select the file and
click Open.

3.

Click Apply. Wait till you
see the massage
“Firmware Upgrade OK!!”. You may now click the Internet
Explorer browser refresh button or press F5. The login page will
appear.

(5) Import

(6) System log

Download to replace the current settings with the configuration
settings file from the computer hard disk to IP camera.

Display the IP camera system event log.

24

ENGLISH

System > General > Date & Time

In the “Date & Time” tab, the administrator can set and update the system’s date and time. After
filling in the correct settings, click Apply to apply the new settings.

Name Function

(1) Current Date & Time
(2) Date Format
(3) Time Zone

Display the current date and time.
Select the date display format.
Set the local time zone. Check the box next to “Enable Daylight

Saving” to enable and setup the start date and end date for
daylight saving time.

25

Name Function

(4) Setting Method

Select the date & time settings method.
Sync with current PC – Obtain the date and time setting on the
current login computer.
Sync with NTP Server – Obtain the date and time setting from
NTP server. In the drop-down list, select the NTP host name.
Manual – Manually set the date and time. Click “Done” to close
the date and time interface.

System > User Management

In this section, only admin level is authorized to create, delete, and edit the account in Account tab and
configure the client connection setting in Connection tab.

System > User Management

IP camera supports two different user accounts – Administrator (Admin) and Guest User.

User Type Access Rights

Admin Can access all the configuration pages
Guest User Can only access the preview page.



Anonymous User Login

 Yes: Allow an anonymous user to view the IP camera without logging in.
 No: Need user name & password to access this IP camera

26



Add user: Enter the user name in “Username”, the password in “Password”, and re-enter the
password in “Confirm”. Then, click “Add/Set”.



User List: Click edit to change the account password. To delete the user account, click Remove
button.

ENGLISH

[Note]

1. The password can’t be empty, otherwise, user are not able to login successfully.

2. Please don’t use special symbols as user name such as *, %, $, &.

27

System > Network Setting > Setting



Device Name: Used to name the IP camera to search more easily for this specific one among all
connected IP cameras.



Network Type: IP camera supports DHCP, static IP and PPPoE. After completed all settings, click
Apply to save the configuration.

− DHCP: Using DHCP, IP camera will get all the network parameters from DHCP server
automatically.

− Static IP: Please enter the IP address, subnet mask, gateway, Primary DNS, and Secondary
DNS.

− PPPoE: Enter the Username, Password and re-enter Password in Confirm Password for
the ADSL connection. And then click Apply to save the configuration.

28

ENGLISH

System > Network Setting > Sever

Used to send out the video via Email or FTP, or to save on NAS.



Mail Setting: Used to send out the video via Email.
a. Login Method: Click drop-down list to select the method to login Email server – “Account” or

“Anonymous”.

b. Enter necessary information in “Bcc Mail”, “Sender Email Address”, “Recipient Email

Address”, “Mail Server”, “Mail Server Port”, “Account Name”, and “Password” columns.

c. Click “Apply” to save the configuration.



FTP Setting: Used to send out the video to FTP server.
a. Enter necessary information in “FTP Server”, “Account Name”, “Password”, and “Path”

columns.

b. Port: Select the FTP server port.

c. If the user wants to create a new folder on the FTP server to save the video file, select “Yes”

under the “Create the folder”.

d. Mode: Select the FTP transmission mode.
e. Click “Apply” to save the configuration.

29



NAS Settings: Used to send out the video to NAS server.
a. Enter necessary information in “Location”, “Workgroup”, “Account Name” and “Password”

columns.

b. If the user wants to create a new folder on the NAS server to save the video file, select “Yes”

under the “Create the folder”.

c. Click “Apply” to save the configuration.

System > Network Setting > DDNS

The IP camera supports DDNS (Dynamic DNS) service.

a. Select “Enabled DDNS” to enable DDNS function.
b. Enter the Domain Name, Account Name, and Password that the user has registered on the

DDNS service provider in the appropriate columns.
c. Enter the IP refreshing time period in the “Schedule Update” column.
d. Click “Apply” to save the configuration.
[Note] If you set up schedule update to occur too frequently, the IP may be blocked. In general,
performing schedule update once a day (1440 minutes) is recommended.

30



Status

- Common warning message:

Updating!
Failed(1), Please check your DNS setting.
Failed(2), Please check your internet connection.
Failed(3), Please check your internet connection.
Failed(6), receiving data failure

- Warning message from different service provider:
 Server Provider : dyndns.org

Failed(4),Please check the Dyndns.org.
Error : The system parameter given is not valid.
Error : No user agent was specified.
Error : The username and password pair do not match a real user.
Error : An option available only to credited users was specified.
Error : Not in the form hostname.domain.org or domain.com.
Error : The hostname specified does not exist.
Error : Not under the username specified.
Error : Too many or no hosts specified in an update.
Error : The hostname specified is blocked for update abuse.
Error : DNS error encountered.
Error : DNS Server Error Conditions.

 Server Provider : ddns.camddns.com(TW)

Failed(5), The name has already been registered.

 Server provider : ddns.ipddn.com(HK)

Failed(5), The name has already been registered

 Server provider : www.3322.org.

Failed(4), Please check the www.3322.org.

ENGLISH

31

System > Network Setting > Other 1

User may need to assign different port to avoid conflict when setting up IP assignment. Click Apply to
save the configuration.



HTTP Port: setup web page connecting port and video transmitting port (Default: 80)



HTTPS Port: AVer IP Camera supports encrypted browsing using HTTPS. This is configured on
the System > Advance > HTTPS



UPnP Support: This IP camera supports UPnP, if this service is enabled on your computer, the
camera will automatically be detected and a new icon will be added to “My Network Places.”

[Note] UPnP must be enabled on your PC.
Please follow the procedure to activate UPnP.

1. Open the Control Panel from the Start Menu.

2. Select Add/Remove Programs.

3. Select Add/Remove Windows Components and open Networking Services section.

4. Click Details and select UPnP to setup the service.

5. The IP device icon will be added to “My Network Places”.

6. User may double click the IP device icon to access IE browser.



UPnP Port Forwarding: If the IP camera is set up behind the firewall, please select YES to
enable it.



RTSP Server: Enable/disable RTSP function. The Real Time Streaming Protocol (RTSP) is a
network control protocol designed for use in entertainment and communications systems to control
streaming media servers.



RTSP Authentication: While using iViewer software to get camera’s image, please choose “Basic”
(base64) mode to enable security mechanism.

32



RTSP Port: setup port for RTSP transmitting (Default: 554)



RTP Start and End Port: in RTSP mode, you may use TCP and UDP for connecting. TCP
connection uses RTSP Port (554). UDP connection uses RTP Start and End Port.



Security: Yes is required account and password to connect with this IP camera through ONVIF
protocol. No is not required account and password to connect.



RTSP Keepalive: To keep connection until remote site disconnects it.

ENGLISH

33

System > Network Setting > Other 2

Multicast Setting (based on the RTSP Server): User can setup two streaming based on the RTSP
Server.

Multicast operation example:

The application is to get the multicast streaming in the LAN environment. Basically, the users operate
VLC player, and then you can get the multicast streaming form IP camera.

Please follow the steps to obtain the multicast streaming in the following steps:

Step 1:

1. Implement VLC player (please download from the internet)

2. Select /tools/preferences

34

Step 2:

2. Select Demuxers and
RTP/RTSP

1. Select all

Step 3:

Select Media/open network stream

ENGLISH

3. Select force multicast RTP
via TRSP

35

Step 4:

Input rtsp://[IPCAM Address] / [RTSP Path]
The URL address should be the same as the RTSP path in Video Stream (System-->Video
Stream)

36

[Notice]

a. If the received image is not from the required IP camera, please adjust the value. (Change either

IP Address or Port number)

b. If the Multicast stream you use doesn’t support RTSP Keepalive, please select NO.

ENGLISH

37



Bonjour: This function enables MAC systems to link to this IP Camera. Please key in the name
here.(Safari supports Bonjour protocol)



LLTD: If your PC supports LLTD, enable this function then you can check the connection status,
properties, and device position (like IP address) of this IP Camera in the network map. In the
computer running Windows Vista or Windows 7, you can find LLTD through the path Start 

Control Panel Network and internet Network and Sharing Center Click “ See full map”.

System > Network Setting > IPv6

Beside IPv4, there is IPv6 for users to set up IP address.

38

ENGLISH

System > Advance > HTTPS

HTTPS (Hypertext Transfer Protocol Secure): Https can help protect streaming data transmission

over the internal on the higher security level. You can select the connection type. "Https" means
user cannot connect the camera via Http protocol. The HTTPS path will be: "https ://( IP address)/". If
you select "Http & Https", both the Http and HTTPS path can be used to access the camera

Remove the existing setting: Before setting new request, please remove old secure identification.
Select "Http" connection type and click "Remove".

39

Created Request: Setting the secure identification and apply it.

There are two ways to set Certificate- Install Signed Certificate or Create Self-Signed Certificate.

40

ENGLISH

System > Advance > SNMP

SNMP (Simple Network Management Protocol) provides a simple framework for
administering networked hardware. To manage the IP camera, you have to prepare a MIB
browser or similar tools first. SNMPv1, SNMPv2c, and SNMPv3 can be enabled
simultaneously.



SNMPv1 and SNMPv2:

be roughly regarded as key. The person who has the community name has the
authority to read or edit the information of IP camera via SNMP. Check the box to
enable SNMPv1 or SNMPv2c protocol, and specify the community name for write
(read and write) and read (read-only). The user who uses read community name to
access the IP camera cannot modify any data of this camera.

The term "Community name" in SNMPv1 and SNMPv2c can

41



SNMPv3:

added when developing SNMPv3. The user has to give not only the security name
(the same as "community name" in v1&v2c, or sometimes we call it "context name")
but the password in order to access the IP camera. Please set security name,
authentication type, authentication password, encryption type, encryption password of
write and read respectively. The password must be 8~64 bits in length. Different from
in SNMPv1 and v2c, the user have to create a account when using SNMPv3. In the
account parameters, key in the security name and password you set in the camera to
get accessing.



SNMPv1/v2cTrap:

messages to manager instead of waiting passively for polling from the manager.
Specify the trap event. When those events happen, the camera will send the ring
message to the Trap Address, which is usually the manager's IP address. Trap
Community means the community that can receive the trap message.

-

-

-



V3 Authentication Failed:

failed. (Due to incorrect password or community)



SD Insert / Remove:

For data security reason, the authentication and encryption assurances are

Trap is a mechanism that allows the managed device to send

Cold Start:
Setting changed:
Network Disconnected:

will send trap messages after the network being connected again)

The camera starts up or reboots.

The SNMP setting is changed.

The network connection was broken down. (The camera

A SNMPv3 user account tries to get authentication but

A microSD/SDHC card is inserted or removed.

42

ENGLISH

System > Advance > Access list

You can deny an IP address or a range of IP address so that they cannot access the IP camera. Tick
the "enable" box, key in the IP address you want to deny, select" deny" then click "Add" to add it to the
list. You can also choose to deny a range of IP address but allow one or several IP address of them.
Take the picture above for example, IP address192.168.50.151~161 is not allowed to connect to the
camera, but only 192.168.50.159 can access. Note: In the list "allow" condition must be ranked before
"deny" condition. For example, if we exchange the sequence, set "Deny: 192.168.50.151 ~

192.168.50.161" for the first item and "Allow: 192.168.50.159" for the second item in the list, the IP
"192.168.50.159" turns out to be denied by the camera because the "deny" condition has the priority
according to our ranking way.

43

System > Advance > QoS/DSCP

QoS/DSCP (Quality of Server/Differentiated Services Code-point) specifies a simple mechanism for

classifying and managing network traffic and provide QoS on IP networks. DSCP is a 6-bit in the IP
header for packet classification purpose. The number 0~63 for Live Stream, Event / Alarm, and
Management represent the ratio that the bandwidth is divided. For example, if you set5, 10, and 20 for
the three items, then the bandwidth of the three item is 5:10:20. There is no difference between setting
"0, 0, 0" or "63, 63, 63" because under these two setting the three items will get equal bandwidth (1/3).

44

ENGLISH

System > Image

Admin and operator levels can adjust the Image setting. There are 4 tabs: OSD, Preference,
Advanced, and Privacy Mask

System > Image> OSD

In OSD tab, you can enable/disable overlaying time stamp and text title. After completing the setting,
click Save to apply the new setting and Cancel to keep the new setting.



Time Stamp: Mark Enable check box and select a position where date and time stamp / text to
display on video screen.



Customize Title: Click Enabled can adjust the OSD contents which are including Alpha of text.

45

System > Image > Preference

In Preference tab, you can tune the IP camera white balance, change the video orientation, and adjust
the brightness and contrast.



White Balance: Adjust white balance value.



Video Orientation: To Flip or Mirror the video on screen.



D-WDR: This function is able to reduce the contrast in the view to avoid the dark zones resulting

from over and under exposure.



Adjust “Brightness”, “Contrast”, “Hue”, “Saturation” to get clear video.

46

ENGLISH

System > Image> Advanced

Click Default button will back to factory default setting.



Shutter Time: Adjust the shutter time level to get the best image quality.



Sense-UP: The main purpose of sense-up is to provide a camera technology that does not rely on

artificial light to see in very low light conditions. By The shutter stays open longer, allowing more
light into the camera and seeing better in low light. This setting altogether when there is a moving
object in the image and the faster the object moves, the worse the image appears (blurriness).



DNR (Denoise): This function is able to filter the noise and blur from the image and show a clearer

view.
[Note] When you select a number in "Shutter Time", actually the shutter time varies in a range and
controlled by camera automatically. Following table shows the shutter time option and corresponding
range

Option Shutter Time Range (sec.)

Outdoor 1/10000 ~ Selected number in "Sense-up"
1/5 1/10000 ~ 1/5
1/10 1/10000 ~ 1/10
1/15 1/10000 ~ 1/15
1/30 1/10000 ~ 1/30

47

Option Shutter Time Range (sec.)

Indoor

1/30 1/10000 ~ 1/30
1/50 1/10000 ~ 1/50
1/60 1/10000 ~ 1/60
1/100 1/10000 ~ 1/100
1/125 1/10000 ~ 1/125
1/250 1/10000 ~ 1/250
1/500 1/10000 ~ 1/500
1/1000 1/10000 ~ 1/1000

NTSC: 1/125 ~ Selected number in "Sense-up"
PAL: 1/100 ~ Selected number in "Sense-up"

48

System > Image> Privacy Mask

For the security purpose, there are three areas can be setup for privacy mask. Click Area #(Area 1,
Area 2, Area 3)button first and drag a area on the image screen. Then, click Save button to save the
setting.

ENGLISH

49

System > Video Stream > General



Input Resolution: Select the video resolution that is the maximum resolution supported in Stream

1 and Stream 2. Please note that when changing the input resolution, the camera will need

to reboot and it takes around 40 sec. When it reboots completely, it will connect to NVR

automatically unless the IP address is changed.



Video System: Select the video format: PAL or NTSC

50

ENGLISH

System > Video Stream > Stream1



Basic Mode

Click Apply to save the configuration.

− Resolution: There are 6 resolutions can be chosen – 1280x1024, 1280x800, 1280x720,
640x480, 320x240, 176x144.

− Quality: There are 5 levels to adjust – Best, High, Standard, Medium, and Low. The higher the
quality is, the bigger the file size is. Also not good for internet transmitting.

− Video Frame Rate: The video refreshing rate per second.

− Video Format: H.264 or JPEG.

− RTSP Path: It’s a URL address.



Advanced Mode
Click Apply to save the configuration.

− Resolution: There are 6 resolutions can be chosen -- 1280x1024, 1280x800, 1280x720,
640x480, 320x240, 176x144. .

− Rate Control: There are CBR (Constant Bit Rate) and VBR (Variable Bit Rate) to use.
 CBR: 32Kbps~8Mbps (the higher the CBR is, the better the video quality is).



VBR: 1(Low) ~10(High) – Compression rate, the higher the compression rate, the better
the picture quality is; vise versa. The balance between VBR and network bandwidth will
affect picture quality. Please carefully select the VBR rate to avoid picture breaking up or
lagging.

− Video Quantitative:1(Low) ~10(High).When you select VBR setting, you can adjust the value.

− Video Frame Rate: The video refreshing rate per second.

51

− Video Frame Rate: The video refreshing rate per second.

− GOP Size: It means "Group of Pictures".

− Video Format: H.264 or JPEG

− RTSP Path: It’s a URL address

52

ENGLISH

System > Video Stream > Stream2



Basic Mode
Click Apply to save the configuration.

− Resolution: There are 6 resolutions can select -- 1280x1024, 1280x800, 1280x720, 640x480,
320x240, 176x144. .

− Quality: There are 5 levels to adjust – Best, High. Standard, Medium, and Low. The higher the
quality is, the bigger the file size is. Also not good for internet transmitting

− Video Frame Rate: The video refreshing rate per second.

− Video Format: H.264 or JPEG

− RTSP Path: It’s a URL address

53



Advanced Mode
Click Apply to save the configuration.

− Resolution: There are 6 resolutions can select -- 1280x1024, 1280x800, 1280x720, 640x480,
320x240, 176x144.

− Profile: Profiles are different compression way of H.264. High profile provides better coding
efficiency. Note that some devises do not support every profile. For example, iPhone4 only
supports Main profile

− Rate Controls: CBR or VBR

− Video Bitrate: Select the bitrate of video.

− Video Frame Rate: The video refreshing rate per second.

− Video Format: H.264 or JPEG.

− RTSP Path: It’s a URL address



Close: To close the stream 2. Click Apply to save the configuration.

54

To get the best mobile viewing quality, please download AVeriViewer (AndroidViewer) from

Apple App store or Google Play. iViewer takes video from Stream 1 or Stream 2, not from 3GPP

System > Video Stream > Stream3

3GPP Streaming is designed for mobile viewing.



Stream 3 Setting: Enable or Disable 3GPP Streaming.



3GPP Path: It’s a URL address.

[Note]

1.

ENGLISH

the

streaming.

55

System > Audio

IP camera supports 2-way audio (mono). User can send audio from IP camera while connected to a
microphone to remote site; User can also send audio from remote site to IP camera’s external speaker.

a. IP camera to PC: select “Enable” to start this function.
b. In live video screen, click button to start chatting. Press again to mute. Click button to

turn on or off the speaker of PC.

c. There are three audio codes: G.711 (64Kbps), G.726(24Kbps), G.726 (32Kbps)

56

ENGLISH

System > SD Card

Please insert microSD/SDHC card before use it. Make sure pushing microSD/SDHC card into the slot
completely.

57

Event > Arrangement > Motion

Motion Detection: IP camera allows 3 areas motion detection. When motion is triggered, it can send

the video to some specific mail addresses, transmit the video to remote ftp server, trigger the relay,
and save video to local SD/SDHC card. To set up the motion area 1, click “Area 1” button. Using
mouse to drag and draw the area. The same operation for area 2 and 3. (The higher the sensitivity
value is, the more sensitive to trigger event.)

58

different types of recording file to change its record size.

When motion/alarm is triggered, there are 3 different types of record mode.

JPEG compression format.

etups for video start and end time when motion detected, I/O, or

camera

in Ram Memory, When information is too much or video

set too high, it will cause recording frame drop or decrease on post alarm

When the network is down, it will save the video to local

to

sure the video recording is continuous. To use this function, key in the IP address of the PC which

”, then click “

card is fixed with 30 seconds.

Event > Arrangement > Preference



Record File:
 File Format: IP camera allows 3

− AVI File (With Record File Setting )

− JPEG Files (With Record File Setting), only with M

− Single JPEG (Single File with Interval Setting) (JPEG photo).

 Pre Alarm and Post Alarm: S

other devices got triggered.

[Note] Pre/Post Alarm record time is base on record time setting and IP
memory. Limited by IP camera built­quality



Network Connected:

[Note]This function is only enabled in wire connection.



Network IP check: When the connection is down, it records the video

ENGLISH

built-in Ram

recording time.

SD/SDHC card.

SD/SDHC card. Make

has recording software installed. Enable the function of “Save to SD card

[Note] The interval of two video files on SD/SDHC

59

Apply”.

Event > Schedule



Schedule: After complete the schedule setup, the camera data will be recorded according to the
schedule setup.



Snapshot: After enable the snapshot function; user can select the storage position of snapshot file,
the Interval time of snapshot and the reserved File Name of snapshot.

60

5V

ENGLISH

Event > DI/DO

IP camera supports 1 input/1 output (depending on different models). When input is triggered, it can
send the video to some specific mail addresses, transmit the video to remote ftp server, trigger the
relay, and save video to local SD/SDHC card.

CAUTION!!

Please connect to propriety relay box to reduce the risk of electric shock & damaged.

Input Setting:

Input 1 sensor: This is to set the relay status while sensor is not yet triggered.
Input 1 action: Send the triggered video clips or photos to the selected method.
Subject: This is the subject while sending files via e-mail.

(1) Non-Triggered

Sensor
Device

(2) Triggered

Sensor
Device

61

Triggered

0V

5V

5V

ALARM

GND

ALARM

GND

Output Setting:

Mode setting:

OnOff Switch: Relay status is based on sensor triggered times.
Time Switch: To restore the original relay status after the interval time.

[Note]GPIO pin define please refer to the part of Front / Back plane & I/O port pin assignment.

Ground (G)

DI

ALARM INPUT:

Normal: 5V (The voltage differential from ALM_IN pin & Ground)
Active: 0V (Short the pin of ALM_IN and Ground pin)

DO

Ground(G)

RELAY OUTPUT:
MAX: 50 mA, DV 5V

Status Information

Click Apply button to save the configuration.



Networking Info: Displays network information of the IP camera.



Product Info:
Server Name: Assigns a name to the IP camera and the name shows on the IP Installer. Also,

displays the related information of the IP camera. Mark Status Bar to display the Server Name of
IP camera on preview interface.
LED indicator: To disable or enable the LED indicator on the IP camera.

62

ENGLISH

Network Configuration

Configuration 1



a. Internet Access: ADSL or Cable Modem
b. IP address: More than one real IP
c. IP camera and PC connect to the internet
d. For fixed real IP, set up the IP into IP camera and PC. For dynamic IP, start PPPoE.

63

Configuration 2



a. Internet Access：ADSL or Cable Modem
b. IP address：one real IP
c. IPcamera and PC connect to the internet
d. Device needed：IP sharing
e. Use virtual IP, set up port forwarding in IP sharing.(Please refer to Network Setting  Other 1 

UPnP Port Forwarding)

64

ENGLISH

Factory Default

1. To recover the default IP address and password, please follow the following steps.

2. Remove power and Ethernet cable and the dome cover.

3. Press and hold the button and connect power and Ethernet cable to the camera again and hold for
round 20 seconds for system booting.

4. Release the button when camera finishes proceed.

5. Re-login the camera using the default IP (http://192.168.1.168) or DHCP, and user name (admin),
password (admin).

65

Troubleshooting

Here are some useful tips on how to solve some common problems.

Problem Solution

I forgot the account and password for
FV1306. How can I go back to default
setting?

I can’t find a way to force day mode and
night mode. Is this possible and how.

I recorded video file in H.264 file format
but failed to playback on Media Player
(V.9).

When I use Chinese words as the Gmail
title while motion triggered, it turns to be
nonsense characters displayed on my
Gmail.

I use VLC and connect three RTSP
streams (stream 1, 2, 3) at the same
time. However, it can’t work properly.

Please refer to the manual of “Factory Default setting”
description.

We don't provide this function due to the limitation of
hardware.

Default Windows Media Player doesn’t have H.264
decoder so that you can’t playback the file
successfully. Please install K-Lite program in advance
or install KMPlayer or VLC program to playback the
video file. You can search those free programs on
Internet.

It’s the spec limitation and please only use English or
numbers as mail title to avoid this phenomenon.

Due to spec limitation, please connect one stream
each time.

66

ENGLISH

Appendix

FV1306 is compliant with microSD/SDHC card and to ensure recording quality, and please use
memory cards over 2G and Class 4 above (Max. 32G)

MicroSD/SDHC card

Transcend SDHC class4 16GB

Transcend SD class4 16GB

Transcend SDHC class4 32GB

Transcend SD class4 32GB

Transcend SD class6 4GB

Transcend SDHC class6 4GB

Transcend SD class6 8GB

Transcend SDHC class6 8GB

Transcend SD class6 16GB

Transcend SDHC class6 16GB

Transcend SDHC class10 4GB

Transcend SDHC class10 8GB

Transcend SDHC class10 16GB

SanDisk SDHC class4 4GB

SanDisk SDHC class4 8GB

SanDisk SDHC class4 16GB

SanDisk SDHC class4 32GB

67

COPYRIGHT

© 2013 AVer Information Inc. All rights reserved.

All rights of this object belong to AVer Information Inc. Reproduced or transmitted in any form
or by any means without the prior written permission of AVer Information Inc. is prohibited. All
information or specifications are subject to change without prior notice. “AVer” is a trademark
owned by AVer Information Inc. Other trademarks used herein for description purpose only
belong to each of their companies.

NOTICE

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. THE
INFORMATION CONTAINED HEREIN IS TO BE CONSIDERED FOR REFERENCE ONLY.

WARNING

TO REDUCE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO
RAIN OR MOISTURE. WARRANTY VOID FOR ANY UNAUTHORIZED PRODUCT
MODIFICATION.

THE MARK OF CROSSED-OUT WHEELED BIN INDICATES THAT THIS
PRODUCT MUST NOT BE DISPOSED OF WITH YOUR OTHER HOUSEHOLD
WASTE. INSTEAD, YOU NEED TO DISPOSE OF THE WASTE EQUIPMENT BY
HANDING IT OVER TO A DESIGNATED COLLECTION POINT FOR THE
RECYCLING OF WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT. FOR
MORE INFORMATION ABOUT WHERE TO DROP OFF YOUR WASTE
EQUIPMENT FOR RECYCLING, PLEASE CONTACT YOUR HOUSEHOLD
WASTE DISPOSAL SERVICE OR THE SHOP WHERE YOU PURCHASED THE
PRODUCT.

68

Limited Warranty

AVer Information, Inc. (“AVer”) warrants that the applicable product (“Product”) substantially conforms
to AVer’s documentation for the product and that its manufacture and components are free of defects
in material and workmanship under normal use. “You” as used in this agreement means you
individually or the business entity on whose behalf you use or install the product, as applicable. This
limited warranty extends only to You as the original purchaser. Except for the foregoing, the Product is
provided “AS IS.” In no event does AVer warrant that You will be able to operate the Product without
problems or interruptions, or that the Product is suitable for your purposes. Your exclusive remedy
and the entire liability of AVer under this paragraph shall be, at AVer’s option, the repair or replacement
of the Product with the same or a comparable product. This warranty does not apply to (a) any Product
on which the serial number has been defaced, modified, or removed, or (b) cartons, cases, batteries,
cabinets, tapes, or accessories used with this product. This warranty does not apply to any Product
that has suffered damage, deterioration or malfunction due to (a) accident, abuse, misuse, neglect, fire,
water, lightning, or other acts of nature, commercial or industrial use, unauthorized product
modification or failure to follow instructions included with the Product, (b) misapplication of service by
someone other than the manufacturer’s representative, (c) any shipment damages (such claims must
be made with the carrier), or (d) any other causes that do not relate to a Product defect. The Warranty
Period of any repaired or replaced Product shall be the longer of (a) the original Warranty Period or (b)
thirty (30) days from the date of delivery of the repaired or replaced product.

Limitations of Warranty

AVer makes no warranties to any third party. You are responsible for all claims, damages, settlements,
expenses, and attorneys’ fees with respect to claims made against You as a result of Your use or
misuse of the Product. This warranty applies only if the Product is installed, operated, maintained, and
used in accordance with AVer specifications. Specifically, the warranties do not extend to any failure
caused by (i) accident, unusual physical, electrical, or electromagnetic stress, neglect or misuse, (ii)
fluctuations in electrical power beyond AVer specifications, (iii) use of the Product with any accessories
or options not furnished by AVer or its authorized agents, or (iv) installation, alteration, or repair of the
Product by anyone other than AVer or its authorized agents.

Disclaimer of Warranty

EXCEPT AS EXPRESSLY PROVIDED OTHERWISE HEREIN AND TO THE MAXIMUM EXTENT
PERMITTED BY APPLICABLE LAW, AVER DISCLAIMS ALL OTHER WARRANTIES WITH
RESPECT TO THE PRODUCT, WHETHER EXPRESS, IMPLIED, STATUTORY OR OTHERWISE,
INCLUDING WITHOUT LIMITATION, SATISFACTORY QUALITY, COURSE OF DEALING, TRADE
USAGE OR PRACTICE OR THE IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A
PARTICULAR PURPOSE OR NONINFRINGEMENT OF THIRD PARTY RIGHTS.

Limitation of Liability

IN NO EVENT SHALL AVER BE LIABLE FOR INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY,
PUNITIVE, OR CONSEQUENTIAL DAMAGES OF ANY NATURE INCLUDING, BUT NOT LIMITED
TO, LOSS OF PROFITS, DATA, REVENUE, PRODUCTION, OR USE, BUSINESS INTERRUPTION,
OR PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES ARISING OUT OF OR IN
CONNECTION WITH THIS LIMITED WARRANTY, OR THE USE OR PERFORMANCE OF ANY
PRODUCT, WHETHER BASED ON CONTRACT OR TORT, INCLUDING NEGLIGENCE, OR ANY
OTHER LEGAL THEORY, EVEN IF AVER HAS ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES. AVER’S TOTAL, AGGREGATE LIABILITY FOR DAMAGES OF ANY NATURE,
REGARDLESS OF FORM OF ACTION, SHALL IN NO EVENT EXCEED THE AMOUNT PAID BY
YOU TO AVER FOR THE SPECIFIC PRODUCT UPON WHICH LIABILITY IS BASED.

69

Governing Law and Your Rights

This warranty gives you specific legal rights; You may also have other rights granted under state law.
These rights vary from state to state.

70