One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
y
www.panelook.com
Product Specification
M190PW01 V5
AU OPTRONICS CORPORATION
Record of Revision
Version and Date Page Old description New Description Remark
0.1 2009/1/12 all First edition for all customer N/A V0.1
0.2 2009/2/03 5
6
20 T6:Max 100 T6 :Max -
White x : Min:0.617, Typ:0.647, Max:0.677
White y:Min: 0.308, Typ: 0.338, Max: 0.368
White x : Min:0.283, Typ:0.313, Max:0.343
White y : Min:0.299, Typ:0.329, Max:0.359
Note 1: For Pb Free products, AUO will
add
for identification.
Note 2: For RoHS compatible products,
AUO will add
Note 3: For China RoHS compatible
0.3 2009/4/09 26 NA
products, AUO will add
identification.
Note 4: The Green Mark will be
presentedonl
when the green
documents have been ready by AUO
Internal Green Team.
1.0 2009/4/23 5
Weight :2250g (typ)
Weight :2210g (typ)
for identification.
for
V0.2
V0.2
V0.2
V0.3
document version 1.0 3/28
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
Product Specification
AU OPTRONICS CORPORATION
M190PW01 V5
1. Handling Precautions
1) Since front polarizer is easily damaged, pay attention not to scratch it.
2) Be sure to turn off power supply when inserting or disconnecting from input connector.
3) Wipe off water drop immediately. Long contact with water may cause discoloration or spots.
4) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.
5) Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface.
6) Since CMOS LSI is used in this module, take care of static electricity and insure human earth
when handling.
7) Do not open or modify the Module Assembly.
8) Do not press the reflector sheet at the back of the module to any directions.
9) In case if a Module has to be put back into the packing container slot after once it was taken out
from the container, do not press the center of the CCFL reflector edge. Instead, press at the far
ends of the CCFL Reflector edge softly. Otherwise the TFT Module may be damaged.
10) At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor tilt the
Interface Connector of the TFT Module.
11) After installation of the TFT Module into an enclosure, do not twist nor bend the TFT Module even
momentary. At designing the enclosure, it should be taken into consideration that no
bending/twisting forces are applied to the TFT Module from outside. Otherwise the TFT Module
may be damaged.
12) Cold cathode fluorescent lamp in LCD contains a small amount of mercury. Please follow local
ordinances or regulations for disposal.
13) Small amount of materials having no flammability grade is used in the LCD module. The LCD module
should be supplied by power complied with requirements of Limited Power Source (IEC60950 or
UL1950), or be applied exemption.
14) The LCD module is designed so that the CCFL in it is supplied by Limited Current Circuit (IEC60950 or
UL1950). Do not connect the CCFL in Hazardous Voltage Circuit.
document version 1.0 4/28
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
Product Specification
AU OPTRONICS CORPORATION
M190PW01 V5
2. General Description
This specification applies to the 19 inch-wide Color TFT-LCD Module M190PW01.
The display supports the WXGA+ (1440(H) x 900(V)) screen format and 16.7M colors. All input signals are 2 Channel
LVDS interface compatible.
This module does not contain an inverter card for backlight.
.
2.1 Display Characteristics
The following items are characteristics summary on the table under 25 к condition:
Items Unit Specifications
Active Area [mm] 408.24 (H) x 255.15(V)
Pixels H x V 1440x3(RGB) x 900
Pixel Pitch [mm] 0.2835x 0.2835
Pixel Arrangement R.G.B. Vertical Stripe
Display Mode TN Mode,Normally White
White Luminance [cd/m2]
300 cd/m
2 @ 7.5mA
(Typ)
Contrast Ratio 1000:1
Optical ResponseTime [msec] 5 (Typ, on/off)
Nominal Input Voltage VDD [Volt] +5.0 (Typ)
Power Consumption
(VDD line + CCFL line)
[Watt] 15.5 (Typ)
Weight [Grams] 2210 (Typ)
Physical Size (H x V x D) [mm] 428.0(W) x 278.0(H) x 16.5(D) (Typ)
Electrical Interface Dual Channel LVDS
Surface Treatment Anti-glare type, Hardness 3H
Support Colors 16.7M colors (RGB 6-bits+HiFRC)
Temperature Range
Operating
Storage (Shipping)
o
[
C]
o
[
C]
0 to +50
-20 to +60
RoHS Compliance RoHS Compliance
document version 1.0 5/28
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
Product Specification
AU OPTRONICS CORPORATION
M190PW01 V5
2.2 Optical Characteristics
The optical characteristics are measured under stable conditions at 25к (Room Temperature):