AT&T EL52103, EL52113, EL52203, EL52213, EL52253 User Manual

...

User’s manual

EL52103/EL52113/EL52203/ EL52213/EL52253/EL52303/ EL52313/EL52333/EL52353/

EL52403/EL52503/EL52513 DECT 6.0 cordless telephone/

answering system with caller ID/call waiting

Congratulations

on purchasing your new AT&T product. Before using this AT&T product, please read Important safety information on pages 85-87 of this user’s manual. Please thoroughly read the user’s manual for all the feature operations and troubleshooting information you need to install and operate your new AT&T product. You can also visit our website at www.telephones.att.com or

call 1 (800) 222-3111. In Canada, dial 1 (866) 288-4268. This telephone meets the California Energy Commission regulations for

energy consumption. Your telephone is set up to comply with the energyconserving standards right out of the box. No further action is necessary.

Model number: EL52103/EL52113 (one-handset system) EL52203/EL52213/EL52253 (two-handset system) EL52303/EL52313/EL52333/EL52353 (three-handset system) EL52403 (four-handset system) EL52503/EL52513 (ve-handset system)

Type: DECT 6.0 cordless telephone/answering system with caller ID/call waiting

Serial number: Purchase date: Place of purchase: Both the model and serial numbers of your AT&T product can be found on

the bottom of the telephone base.

Telephones identied with this logo have reduced noise and

interference when used with most T-coil equipped hearing aids and cochlear implants. The TIA-1083 Compliant Logo is a trademark of the Telecommunications Industry Association. Used under license.

The ENERGY STAR® program (www.energystar.gov) recognizes and encourages the use of products that save energy and help protect our environment. We are proud to mark this product with the ENERGY STAR® label indicating it

meets the latest energy eciency guidelines.

© 2012-2019 Advanced American Telephones. All Rights Reserved. AT&T and the AT&T logo are trademarks of AT&T Intellectual Property licensed to Advanced American Telephones, San Antonio, TX 78219. Printed in China.

Parts checklist

THIS SIDE UP

/ CE CÔTÉ VERS LE HAUT

Battery Pack / Bloc-piles

BT1 162342/BT262342 (2.4V 300mAh Ni-MH

)

WA RNING /

A VERTISSEMENT

DO NOT BURN OR PUNCTURE BA

TTERIES.

NE PA S INCINÉRER OU PERCER LES PILES.

Made in China / Fabriqué en chine BY1021

Your telephone package contains the following items. Save your sales receipt and original packaging in the event warranty service is necessary.

Quick start guide

EL52103/EL52113/EL52203/ EL52213/EL52253/EL52303/ EL52313/EL52333/EL52353/ EL52403/EL52503/EL52513 DECT 6.0 cordless telephone/ answering system with caller ID/call waiting

Quick start guide (s)

Cordless handset (1 for EL52103/EL52113) (2 for EL52203/EL52213/ EL52253) (3 for EL52303/EL52313/ EL52333/EL52353) (4 for EL52403) (5 for EL52503/EL52513)

(1 for EL52103/EL52113) (2 for EL52203/ EL52213/EL52253) (3 for EL52303/EL52313/ EL52333/EL52353) (4 for EL52403) (5 for EL52503/EL52513)

Telephone base

Charger for cordless handset with power adapter installed (1 for EL52203/ EL52213/EL52253) (2 for EL52303/EL52313/ EL52333/EL52353) (3 for EL52403) (4 for EL52503/EL52513)

Battery compartment cover (1 for EL52103/EL52113) (2 for EL52203/ EL52213/EL52253) (3 for EL52303/EL52313/ EL52333/EL52353) (4 for EL52403) (5 for EL52503/EL52513)

Power adapter for telephone base

Wall-mount bracket

Telephone line cordBattery for cordless handset

User’s manual

EL52103/EL52113/EL52203/ EL52213/EL52253/EL52303/ EL52313/EL52333/EL52353/ EL52403/EL52503/EL52513

DECT 6.0 cordless telephone/ answering system with caller ID/call waiting

Table of contents

Getting started

Installation ...............................................................................1

Quick reference guide - handset ..............................2

Quick reference guide - telephone base .............5

Telephone base and charger installation ...........6

Battery installation and charging ............................7

Battery installation .....................................................7

Battery charging ..........................................................9

Wall-mount installation ................................................ 10

Tabletop to wall-mount installation ............ 10

Wall-mount to tabletop installation .............12

Telephone settings

Menu overview ....................................................................13

Handset settings .............................................................. 14

Ringer volume ............................................................. 14

Ringer tone ...................................................................14

LCD language ...............................................................15

Set speed dial voicemail number ...................15

Clear voicemail indication ..................................16

Key tone .......................................................................... 16

Set date/time ..............................................................17

Home area code ........................................................ 18

Dial mode ....................................................................... 18

QUIET mode ................................................................. 19

Telephone base ringer volume ...............................20

Telephone operation

Making, answering and ending calls .....................21

Making a call ..................................................................21

Temporary ringer silencing.................................21

Answering a call ......................................................... 22

Handset speakerphone ........................................ 22

Ending a call..................................................................22

Redial ........................................................................................23

View numbers in the redial list ........................23

Call a number from the redial list .................. 23

Copy a number from the redial list to

the directory ................................................................ 24

Delete a number in the redial list ..................24

Options while on calls ...................................................25

Volume control ..........................................................25

Mute...................................................................................25

Flash/call waiting ...................................................... 25

Temporary tone dialing ........................................26

Chain dialing .................................................................26

Join a call in progress ............................................. 27

Handset locator.................................................................28

Web address ........................................................................28

Intercom ................................................................................. 29

Make and answer an intercom call ...............29

Answer an incoming call during an

intercom call ................................................................29

Call transfer using intercom ..................................... 30

Getting started

Installation

You must install and charge the battery before using the cordless handset.

See pages 7-9 for easy instructions.

Install the telephone base close to a telephone wall jack and an electrical outlet not controlled by a wall switch. The telephone base can be placed on a at surface or vertically mounted on the wall (page 10-11). For optimum range and better reception, place the telephone base in a central and open location.

If you subscribe to high-speed Internet service (DSL- digital subscriber line) through your telephone line, you must install a DSL lter between the telephone line cord and the telephone wall jack (page 6). The lter prevents noise and caller ID problems caused by DSL interference. Please contact your

DSL service provider for more information about DSL lters.

Your product may be shipped with a protective sticker covering the handset or telephone base display - remove it before use.

For customer service or product information, visit our website at

www.telephones.att.com or call 1 (800) 222-3111. In Canada, dial 1 (866) 288-4268.

Avoid placing the telephone base too close to:

Communication devices such as television sets, VCRs, or other

• cordless telephones.

Excessive heat sources.

•

Noise sources such as a window with trac outside, motors, microwave

•

ovens, refrigerators, or uorescent lighting.

Excessive dust sources such as a workshop or garage.

• Excessive moisture.

• Extremely low temperature.

• Mechanical vibration or shock such as on top of the washing machine or

• work bench.

Getting started

Quick reference guide - handset

CHARGE light

On when the handset is charging in the telephone base or charger.

DIR/VOLUME

Press to scroll up while in menus (page 13).

•

Press to increase the listening volume (pages 25

•

and 62). Press to show directory entries when the handset is

•

not in use (page 35). While entering names or numbers in the directory,

•

press to move the cursor to the right (page 32).

REDIAL/PAUSE

Press repeatedly to review the last 10 numbers

•

dialed (page 23). While entering numbers, press and hold to insert a

•

dialing pause (pages 21 and 32).

PHONE/FLASH

Press to make or answer a call (page 21 or 22).

•

During a call, press to answer an incoming call

•

when you receive a call waiting alert (page 25).

While reviewing a caller ID log entry, press

•

repeatedly to add or remove 1 in front of the entry before dialing or saving it to the directory (page 45).

Press and hold to set or dial your voicemail number

•

(page 15).

TONE

Press to switch to tone dialing temporarily during a call if you have pulse service (page 26).

/SPEAKER

Press to turn on the handset speakerphone, press again to resume normal handset use (page 22).

Getting started

Quick reference guide - handset

CID/VOLUME

Press to scroll down while in menus.

• Press to decrease the listening volume (pages 25

• and 62).

Press to show the caller ID log when the handset is

• not in use (page 44).

While entering names or numbers in the directory,

• press to move the cursor to the le (page 32).

MENU/SELECT

Press to display the menu (page 13).

• Once in the menu, press to select an item or save

• an entry or setting (page 13).

OFF/CANCEL

During a call, press to hang up

• While using menus, press to cancel an operation,

• back up to the previous menu, or exit the menu display (page 13); or press and hold to exit to idle mode.

Press and hold while the handset is not in use to

• erase the missed call indicator (page 44).

(page 22).

QUIET#

Press and hold to set and turn on the QUIET mode,

•

or turn it o.

When reviewing a caller ID log entry, press

• repeatedly to view other dialing options.

INT

Press to initiate an intercom conversation or transfer a call.

MUTE/DELETE

During a call, press to mute the microphone (page 25).

• While predialing, press to erase digits (page 21).

• While reviewing the redial list, directory, speed dial

• list or caller ID log, press to delete an individual entry (pages 24, 37, 40 and 46).

Getting started

Quick reference guide - handset

MAIN MENU

Play messages (page 61)

Play messages

ECO

Answering sys (page 49) Directory (page 31) Caller ID log (page 44) Ringers (page 14) Set date/time (page 17) Settings (page 13) Web address (page 28)

Using menus

Press MENU/SELECT to enter the main menu.

Press CID or DIR to scroll through menu items.

Press MENU/SELECT to select or modify an item.

Press OFF/CANCEL to cancel an operation, back up to the previous menu, or exit the menu display.

Getting started

Quick reference guide - telephone base

/REPEAT

Press to repeat a message (page 62).

• Press twice to play the previous message

• (page 62).

Message window

Displays the number of messages or other answering system information.

X/DELETE

Press to delete the message currently

• playing (page 62).

Press twice to delete all old messages

• when the telephone is not in use (page 63).

/SKIP

Press to skip a message (page 62).

/PLAY/STOP

Press to start or stop message playback

• (page 61).

•

During call screening, press to temporarily

turn the call screening on or o (page 59).

/HANDSET LOCATOR

Press to page all handsets (page 28).

/ /-VOLUME+

When the telephone is not in use, press to

• adjust the telephone base ringer volume (page 20).

During call screening or message

• playback, press to adjust the listening volume (pages 59 and 62).

/ANS ON/OFF

Press to turn the built-in answering system

on or o.

Getting started

Telephone base and charger installation

Install the telephone base and charger, as shown below. If you subscribe to high-speed Internet service (DSL - digital subscriber line) through your

telephone line, you must install a DSL lter between the telephone line cord and the telephone wall jack. The lter prevents noise and caller ID problems

caused by DSL interference. Please contact your DSL service provider for

more information about DSL lters.

The telephone base comes ready for tabletop use. If you want to mount your telephone on a wall, refer to Wall-mount installation on pages 10-12 for details.

Plug one end of the telephone line cord into a telephone wall jack.

A DSL lter (not included)

is required if you have DSL high-speed Internet service.

Route the cords through the slots.

Plug the other end of the telephone line cord into the telephone line jack on the bottom of the telephone base.

Plug the large end of the base power adapter into an electrical outlet not controlled by a wall switch.

Plug the small end of the base power adapter into the power jack on the bottom of the telephone base.

Plug the large end of the charger’s power adapter into an electrical outlet not controlled by a wall switch.

Ensure the small end of the charger’s power adapter is plugged into the power jack on the bottom of the charger.

IMPORTANT INFORMATION:

Use only the power adapter(s) provided with this product. To obtain a replacement, visit our website

at www.telephones.att.com or call

1 (800) 222-3111. In Canada, dial 1 (866) 288-4268.

Getting started

HIS

CÔTÉ VERS

E HAUT

Battery

Pack

1623

BT26

2342

(2.4

00mAh Ni-MH)

MENT

T BURN OR

UNCTURE

RIES

INCINÉ

R OU PERCER LE

n Chi

abriqu

n chi

THIS

Battery Pack / Bloc-pil

BT162342/

BT2623

RNING /

ERTISSEMEN

DO NOT BURN OR PUNCTURE

S INCINÉRER OU PE

Made in China / Fabriqué

Battery installation and charging

Battery installation

Install the battery, as shown below.

Plug the battery connector securely into the socket inside the handset

1. battery compartment, matching the orientation of the engraved label. Insert the supplied battery with the label THIS SIDE UP facing up, as indicated.

Align the cover at against the battery compartment, then slide it upwards

2. until it clicks into place.

Charge the handset by placing it

CHARGE light

3. face up in the telephone base or charger. The CHARGE light is on when charging.

Getting started

Battery installation and charging

Battery installation

To replace the battery, press the tab and slide the

battery compartment cover downwards. Li out the old

battery and disconnect it from the handset. Follow the instructions to install and charge the new battery.

IMPORTANT INFORMATION:

Use only the supplied rechargeable battery or replacement battery (model BT162342/ BT262342). To order, visit our website at www.telephones.att.com or call

1 (800) 222-3111. In Canada, dial 1 (866) 288-4268.

Getting started

Battery installation and charging

Battery charging

Once you have installed the battery, the screen indicates the battery status (see the following table). If necessary, place the handset in the telephone base or charger to charge the battery. For best performance, keep the handset in the telephone base or charger when not in use. The battery is

fully charged aer 16 hours of continuous charging. See Technical specifications on page 94 for battery operating times.

If the screen is blank, you need to charge the handset without interruption for at least 30 minutes to give the handset enough charge to use the telephone for a short time. The screen shows Low battery until you have charged the battery without interruption for at least 30 minutes. The following table summarizes the battery charge indicators and actions to take.

Battery indicators Battery status Action

The screen is blank or shows Put in charger.

The screen shows Low battery and ashes.

The screen shows HANDSET X

and the battery icon shows .

NOTES:

If you are on a call in low battery mode, you hear 4 short beeps every 50 seconds.

•

If no battery is installed in the handset when you place it in the telephone base or charger,

• the screen shows No battery. Follow the instructions in Battery installation on page 7 to install the battery.

Aer you install your telephone or power returns following

a power outage, the handset will prompt you to set the date and time (see page 17). To skip setting the date and

Battery has no or very little charge. The handset cannot be used.

Battery has enough charge to be used for a short time.

Battery is charged. To keep the battery charged,

Charge without interruption (at least 30 minutes).

place it in the telephone base or charger when not in use.

Date: MM/DD/YY

ECO

time, press OFF/CANCEL.

Getting started

Wall-mount installation

The telephone base comes ready for tabletop use. If you want to mount your telephone on a wall, use the provided wall-mount bracket to connect with a standard dual-stud telephone wall-mounting plate. If you do not have this mounting plate, you can purchase one from many hardware or consumer electronics retailers. Professional assistance may be required to install the mounting plate.

Tabletop to wall-mount installation

To change the telephone base from tabletop installation to wall-mount

installation, make sure you rst unplug the power adapter from the electrical

outlet and the telephone line cord from the telephone wall jack.

Plug the power cord and telephone line into the telephone base. If you

are using a DSL lter, plug the other end of the telephone line into the lter. Route the telephone line cord (or DSL lter) through the wall-mount

bracket hole. Position the telephone base, as shown below. Insert the extended tabs

2. (see illustration 2) of the wall-mount bracket into the slots on the back of the telephone base (marked B). Push the telephone base down until it is securely in place.

A DSL lter (not included) is

required if you have DSL high-speed Internet service.

Wall-mount bracket

Getting started

Wall-mount installation

Plug the telephone line cord (or DSL lter) into the wall jack. Plug the

3. power adapter into a power outlet not controlled by a wall switch.

Align the holes on the wall-mount bracket with the standard wall plate

4. and slide the wall-mount bracket down until it locks securely. Bundle the telephone line cord and power adapter cord neatly with twist ties.

A DSL lter (not included) is

required if you have DSL high-speed Internet service.

DSL lter

Getting started

Wall-mount installation

Wall-mount to tabletop installation

To change the telephone base from wall-mount installation to tabletop installation, follow the steps, as mentioned below.

If the telephone line cord and power adapter cord are bundled, untie

them rst.

Push the telephone base up to detach it from the wall-mount bracket.

Unplug the telephone line cord (or DSL lter) from the wall. Unplug the

power adapter from the power outlet. Push the wall-mount bracket up to remove it from the wall.

3. Refer to Telephone base and charger installation on page 6 to install the

4. telephone base.

Telephone settings

Menu overview

Use the menu to change the telephone settings.

Press MENU/SELECT in idle mode (when handset is not in use) to enter the

1. main menu.

Press CID or DIR to scroll through menu items.

2. Press MENU/SELECT to select or save the indicated item.

-OR- Press OFF/CANCEL to cancel an operation, back up to the previous menu or exit the menu display. Press and hold OFF/CANCEL to cancel an operation and return to idle mode.

Telephone settings

Handset settings

Ringer volume

You can set the handset ringer volume level (1-6), or turn the ringer o. When the ringer is o, and Ringer o appears on the handset screen.

Press MENU/SELECT in idle mode to enter the main menu.

1. Press CID or DIR to scroll to Ringers, then press

MENU/SELECT.

Press MENU/SELECT to select Ringer volume.

3. Press CID or DIR to sample each volume level.

4. Press MENU/SELECT to save your preference.

NOTES:

Changing the handset ringer volume does not aect the base ringer volume. For more

• information on the base ringer volume, see Telephone base ringer volume on page 20.

The handset ringer volume also determines the ringer volume of intercom calls and

• paging tones.

If the ringer volume is set to o on a handset, that handset is silenced for all incoming calls

• except paging tone (see Handset locator on page 28).

While the telephone is ringing, press OFF/CANCEL or MUTE/DELETE to silence the ringer

• temporarily on that handset only (see Temporary ringer silencing on page 21).

Ringer volume

ECO

Volume:

ECO

Ringer tone

You can choose one of 10 ringer tones for the handset.

Press MENU/SELECT in idle mode to enter the main menu.

1. Press CID or DIR to scroll to Ringers, then press

MENU/SELECT.

Press CID or DIR to scroll to Ringer tone, then press

MENU/SELECT.

Press CID or DIR to sample each tone.

4. Press MENU/SELECT to save your preference.

NOTE: If you turn o the handset ringer volume, you will not hear ringer tone samples.

Ringer tone

ECO

Tone: 1

ECO

Telephone settings

Handset settings

LCD language

You can select the language used for all screen displays.

Press MENU/SELECT in the idle mode to enter the

1. main menu.

Press CID or DIR to scroll to Settings, then press

MENU/SELECT.

Press MENU/SELECT to select LCD language.

3. Press CID or DIR to select English, Français

4. or Español.

Press MENU/SELECT twice to save your preference.

NOTE: If you accidentally change the LCD language to French or Spanish, you can reset it back to English without going through the French or Spanish menus. Press MENU/SELECT in idle mode, then enter 364# using the dialing keys. You hear a confirmation tone.

Set speed dial voicemail number

If you subscribe to a voicemail service oered by your telephone service

provider, you can save the voicemail number to 1 on each handset for easy access. When you want to retrieve voicemail messages, press and hold

1. Contact your telephone service provider for more information and

assistance about your voicemail service.

To set your voicemail number:

Press MENU/SELECT in idle mode to enter the main menu.

1. Press CID or DIR to scroll to Settings, then press

MENU/SELECT.

Press CID or DIR to scroll to Voicemail #, then press

MENU/SELECT.

Use the dialing keys to enter the voicemail number

4. (up to 30 digits).

Press MENU/SELECT to save. The handset shows

VM # saved and the stored number.

-OR-

If it is your rst time to set the voicemail number:

Press and hold 1 in idle mode.

1. Use the dialing keys to enter the voicemail number (up to 30 digits).

2. Press MENU/SELECT to save. The handset dials the saved voicemail number.

LCD language

ECO

English

ECO

Voicemail #

ECO

Voicemail #

ECO

Telephone settings

Handset settings

Clear voicemail indication

Use this feature when the telephone indicates there is a new voicemail message but there is none. This may occur, for example, when you have accessed your voicemail while away from home. This feature only turns o the displayed New voicemail message and icon; it does not delete your voicemail messages. As long as you have new voicemail messages, your telephone service provider continues to send the signal to turn on the indicators.

To manually turn o the new voicemail indicators:

Press MENU/SELECT when in idle mode to enter the

1. main menu.

Press CID or DIR to scroll to Settings, then press

MENU/SELECT.

Press CID or DIR to scroll to Clr voicemail,

Clr voicemail

ECO

Reset VM Icon?

then press MENU/SELECT. The screen shows Reset VM Icon?.

Press MENU/SELECT to turn the voicemail indication o.

NOTE: For more information about using your voicemail service, contact your telephone service provider for assistance.

ECO

Key tone

The handset is programmed to beep with each key press. You can turn the

key tone o, so there are no beeps when you press keys.

Press MENU/SELECT in idle mode to enter the

1. main menu.

Press CID or DIR to scroll to Settings, then press

MENU/SELECT.

Press CID or DIR to scroll to Key tone, then press

MENU/SELECT.

Press CID or DIR to select On or O.

4. Press MENU/SELECT to save your preference.

Key tone

ECO

Key tone:Off

ECO

Telephone settings

Handset settings

Set date/time

The answering system announces the day of the week and time of each message received prior to playing it. If you subscribe to caller ID service, the day, month and time are set automatically with each incoming call (see About caller ID on page 42). However, the year must be set so that the day of the week can be calculated from the caller ID information.

Follow the steps, as mentioned below, to set the month, date, year and time.

Press MENU/SELECT in idle mode to enter the main

1. menu.

Press CID or DIR to scroll to Set date/time, and then

2. press MENU/SELECT.

Press CID or DIR to select the month, then press

MENU/SELECT, or enter the 2-digit number (01-12)

using the dialing keys (0-9). Press CID or DIR to select the day, then press

MENU/SELECT, or enter the 2-digit number (01-31)

using the dialing keys (0-9). Press CID or DIR to select the year, or enter the

5. 2-digit number (00-99) using the dialing keys (0-9), then press MENU/SELECT.

Press CID or DIR to select the hour, then press

MENU/SELECT, or enter the 2-digit number (00-23)

using the dialing keys (0-9). Press CID or DIR to select the minute, then press MENU/SELECT, or enter

7. the 2-digit number (00-59) using the dialing keys (0-9).

Press CID or DIR to choose AM or PM. Press MENU/SELECT to save.

Set date/time

ECO

Date: MM/DD/YY

ECO

Time: HH:MM - -

ECO

NOTE: If the date and time is not set when the message is recorded, the system announces “Time and date not set” before it plays the message.

Telephone settings

Handset settings

Home area code

If you dial 7 digits to make a local call (no area code required), enter your area code into the telephone as home area code. When you receive a call from within your home area code, the caller ID log only displays the 7 digits of the telephone number.

This feature makes it easy for you to make a call from the caller ID log. If you dial 10 digits to make a local call, do not use this home area code feature. If you do, you will not be able to place calls from your caller ID log because

they have only 7 digits.

Press MENU/SELECT in idle mode to enter the main menu.

Press CID or DIR to scroll to Settings, then press

MENU/SELECT.

Press CID or DIR to scroll to Home area code, then press MENU/SELECT.

Use the dialing keys to enter your 3-digit area code.

4. Press MUTE/DELETE to erase digits while editing.

Press MENU/SELECT to save the setting.

NOTE: If, in the future, your telephone service provider requires you to dial 10 digits to make a local call (area code + telephone number), you need to delete your home area code. While the home area code is displaying in Step 4, press and hold

MUTE/DELETE. The home area code is now restored to its default setting of _ _ _(empty).

Home area code

ECO

Home area code

- - -

ECO

Dial mode

The dial mode is preset to tone dialing. If you have pulse (rotary) service, you must change the dial mode to pulse dialing before using the telephone.

Press MENU/SELECT in the idle mode to enter the main menu.

Press CID or DIR to scroll to Settings, then press

MENU/SELECT.

Press CID or DIR to scroll to Dial mode, then press

MENU/SELECT.

Press CID or DIR to choose between Touch-tone, and Pulse.

Press MENU/SELECT to save the setting.

NOTE: If you have dial pulse (rotary) dialing service only, refer to Temporary tone dialing on page 26 to temporarily switch from pulse to touch-tone dialing during a call.

Dial mode

ECO

Touch-tone

ECO

Telephone settings

Handset settings

QUIET mode

When QUIET mode is turned on, the telephone silences all sounds during the set period of time (1-12 hours). However, the handset locator paging tone and any sound-generating operations initiated by users, such as making calls using the speakerphone or setting ringer volume, will sound as normal. Aer you turn on QUIET mode, this feature activates immediately and the answering system turns on automatically. When QUIET mode is on, the answering system takes calls and records messages without broadcasting them.

To turn QUIET mode on:

1. Press and hold QUIET # in idle mode to enter the QUIET mode setting screen. The screen shows Quiet: _ _ hours [1-12].

2. Use the dialing keys to enter the desired number of hours (1-12) you would like to turn on QUIET mode, then press MENU/SELECT. Your screen briey shows Quiet mode on.

To turn QUIET mode o:

While QUIET mode is on, press and hold QUIET #. The screen shows

•

Quiet mode o briey and then returns to idle.

NOTES:

If you change the base ringer, handset ringer, ringer volume, or key tone when QUIET mode is on,

• the sample plays but the feature is still muted after saving the setting.

After QUIET mode is turned off or the set period of time has expired, all muted features will be

• activated again.

When QUIET mode is on, the handset does not ring when there is an incoming intercom call, but

• the handset which initiates the intercom call does have the calling tone as normal.

Telephone settings

Telephone base ringer volume

When the telephone base is not in use, press

/ /-VOLUME+ on the telephone base to set

the ringer volume level (1-6), or turn the ringer

o. A sample of the ringer sounds as you adjust

the volume. The telephone base announces, “Base ringer is o” when you set the volume to 0.

NOTE: If a handset is on an outside call, the telephone base volume cannot be changed.

Telephone operation

Making, answering and ending calls

Making a call To make a call:

Press PHONE/FLASH or /SPEAKER, then enter

• the telephone number.

On-hook dialing (predialing):

Use the dialing keys to enter the telephone number

1. (up to 30 digits).

Press and hold REDIAL/PAUSE to insert a

• 3-second dialing pause (a P appears).

Press MUTE/DELETE or OFF/CANCEL to erase

• digits.

Press PHONE/FLASH or /SPEAKER to call.

The screen displays the elapsed time as you talk (in hours, minutes and seconds).

PHONE 0:01:30

888-722-7702

ECO

10:30PM 11/20

888-722-7702

ECO

NOTES:

Pressing PHONE/FLASH to access services from your telephone

•

service provider does not aect the elapsed time.

When a handset is on a call and another handset attempts to access the directory, speed dial

• list or caller ID log, the screen of the other handset shows Not available.

10:30PM 11/20

Temporary ringer silencing To silence the ringer temporarily on a handset:

While the telephone is ringing, press OFF/CANCEL or

• MUTE/DELETE.

Ringer muted

ECO

To silence the ringer temporarily on the telephone base:

While the telephone is ringing, press /-VOLUME on the

• telephone base.

This turns o the ringer without disconnecting the call. The next incoming

call rings normally at the preset volume.

Telephone operation

Making, answering and ending calls

Answering a call Press any dialing key (0-9, or #) or PHONE/FLASH.

-OR-

Press /SPEAKER to answer using the speakerphone.

Handset speakerphone

During a call, press /SPEAKER to switch between speakerphone and normal handset use.

Press OFF/CANCEL or return the handset to the telephone base or charger to hang up.

NOTE: Aer installing the battery in the handset, the screen may show Low battery. If you use the speakerphone at this time, the battery may become depleted. Follow the instructions in Battery charging on page 9.

Ending a call Press OFF/CANCEL.

-OR-

Put the handset in the telephone base or charger to end the call.

Speaker 0:01:30

ECO

10:30PM 11/20

Telephone operation

Redial

Each handset stores the 10 most recently called numbers in the redial list.

View numbers in the redial list

Press REDIAL/PAUSE in idle mode.

1. Press DIR, CID or REDIAL/PAUSE repeatedly to

2. scroll through the 10 most recently called numbers (up to 30 digits each). The handset beeps twice at the beginning or end of the list.

Press OFF/CANCEL to exit the redial list.

NOTE: If you access an empty redial list, the handset sounds an error tone.

Call a number from the redial list

Press REDIAL/PAUSE in idle mode.

1. Press DIR, CID or REDIAL/PAUSE repeatedly to scroll

2. through the 10 most recently called numbers (up to 30 digits each). The handset beeps twice at the beginning or end of the list.

When the number you want to call is displayed, press

PHONE/FLASH or /SPEAKER to dial.

-OR-

Press PHONE/FLASH or /SPEAKER.

1. Press REDIAL/PAUSE, then press DIR, CID or REDIAL/PAUSE repeatedly

2. until the number you want to call is displayed.

Press MENU/SELECT. The handset dials the desired number.

Redial #1/7 888-722-7702

ECO

NOTE: If you press REDIAL/PAUSE when the redial list is empty, the handset sounds an error tone.

Telephone operation

Redial

Copy a number from the redial list to the directory

Press REDIAL/PAUSE.

1. Press CID or DIR to scroll to the number you want to

2. save into the directory. Press MENU/SELECT twice. The screen shows Enter number.

Press CID or DIR to move the cursor to the le

• or right.

Press and hold REDIAL/PAUSE to enter a 3-second

• dialing pause (a P appears).

Press MUTE/DELETE to erase a digit.

• Press and hold MUTE/DELETE to erase all digits.

•

Press MENU/SELECT again to save the number and edit

3. the name. The screen shows Enter name.

Use the dialing keys (0-9) to edit the name.

• Press 0 to add a space.

• Press MUTE/DELETE to erase a character.

• Press and hold MUTE/DELETE to erase all characters.

•

Press MENU/SELECT to store your new directory entry. The handset shows

Saved and sounds a conrmation tone.

Enter number 888-722-7702_

ECO

Enter name

ECO

Delete a number in the redial list

While reviewing a number in the redial list, press

MUTE/DELETE to delete the displayed number from the

redial list.

+ 74 hidden pages