REVISED
5/7/02
Expansion Handset 2402
Fold open this manual for information
about this product’s installation
and operation. Please also
read Part 1 — Important
Product Information.
© 2001 Advanced American Telephones.
All rights reserved.
AT&T and the Globe Design are
trademarks of AT&T Corp. licensed to
Advanced American Telephones.
Printed in China. Issue 2AT&T 05/02
Visit us at www.telephones.ATT.com
© 2001 Advanced American Telephones. All rights reserved.
AT&T and the Globe Symbol are trademarks of AT&T Corp. licensed to Advanced American Telephones.
USER’S MANUAL
Part 2
2402_map_2ATT 5/7/02 6:32 PM Page 6
BEFORE YOU BEGIN
1
About Handset Registration
• You must register this (and any other) handset with the base,
following the directions in “REGISTER THE HANDSET.” This handset is
compatible with telephone model 2462.
• The original handset that came with the base is automatically
registered as Handset 1.
• Additional handsets will be assigned Handset 2, Handset 3, Handset 4,
Handset 5, Handset 6, Handset 7, and Handset 8.
• Whenever you install a handset battery pack, the handset will display
SEARCHING FOR BASE (if it’s registered) or ENTER BASE ID (if it’s
not registered).
About Softkeys
• The handset softkeys are located below the screen display.
• Press the softkey below the operation displayed on the screen to
select that operation. (For example, to enter the menu, press the
center softkey).
• Press O (CLEAR) at any time to return to the previous screen.
• Press and hold O (CLEAR) to return to the idle screen.
Softkeys
Screen
display of
operations to
be selected
with softkeys.
2402_map_2ATT 5/7/02 6:32 PM Page 1
CHARGE THE BATTERY
2
1 Install the handset battery pack.
Use only the battery supplied with this handset or AT&T Accessory
Battery Model 2401, SKU#91077.
• When you install the battery pack the first time, the handset will
display ENTER BASE ID.
2 Charge the handset battery.
• Place the handset in the remote charging stand (purchased
separately). The CHARGING light goes on.
• Charge the battery at least 12 hours. After the first charge,
the battery typically charges in only eight hours.
b) Place the battery pack in
the handset. Match the
metal contacts on the
battery with the contacts
in the battery
compartment.
c) Replace cover
by sliding it on
its track up
over battery
case until it
snaps firmly
into place.
a) Remove
battery
compartment
cover by
pressing on
indentation
and sliding
downward.
2402_map_2ATT 5/7/02 6:32 PM Page 2
REGISTER THE HANDSET
1 Make sure to charge the handset battery pack at least 12 hours.
2 At the 2462 corded base, press .
3 Use or to select DISPLAY BASE-ID.
4 Press . The base screen will display the 15-digit Base ID code
for about 30 seconds, then return to the idle screen. Write down the
Base ID code so you can enter it at the handset in STEP 6 below.
5 At the cordless handset, use the softkey to select REGISTER.
6 Enter the 15-digit Base ID code.
7 Use the softkey to select OK. The screen displays PLEASE WAIT!!.
8 After about 45 seconds, the screen displays FOUND BASE. If the
handset displays BASE BUSY TRY LATER, the base is in use.
For complete operation instructions,
refer to the manual that came with
your original handset.
OK
MENU
3
2402_map_2ATT 5/7/02 6:32 PM Page 3
INSTALLATION
4
Belt Clip
Attach the belt clip (optional).
Headset
You can use this telephone
hands-free when you install
any industry standard
2.5 mm headset (purchased
separately). For best results,
use an AT&T 2.5 mm
headset.
Plug the headset into the
jack located on the left side
of the handset (under the
small rubber flap). Do not
force the connection, but
make sure the plug fits
securely.
a) Slide down into
grooves to attach.
b) To remove, lift one side
with your thumbnail
and push back.
2402_map_2ATT 5/7/02 6:32 PM Page 4
5
Battery Life
Battery life depends on how far the handset is from the base, and other
environmental conditions.
NOTE: For optimum performance, charge your cordless handset in
the handset charger every night.
Charge the Handset Battery Pack
• This battery should remain charged for up to five days. A fully charged
battery provides an average talk time of about six to eight hours.
• The battery pack needs charging when:
– The battery icon ( ) flashes,
– A warning tone sounds, or
– The screen displays LOW BATTERY when idle.
• Place the handset in the handset charger so the CHARGING light
goes on. The battery pack is typically charged in eight hours. For best
results, the initial charge should be twelve hours.
• You can keep the battery fully charged by returning the handset to
the handset charger after each use.
• If you repeatedly get a Low Battery indicator, even after eight hours of
charging, the battery should be replaced. Use only AT&T Accessory
Battery Model 2401, SKU# 91077.
CAUTION: Charge the battery provided with or identified for use
with this product only in accordance with the instructions and
limitations specified in the User’s Manual, Part 1.
2402_map_2ATT 5/7/02 6:32 PM Page 5
Loading...