This cordless product provides you with two cordless handsets,a base
station and a spare charger. You can charge either handset in the base or in
the spare charger. You’ll need to connect the base to both AC power and a
modular telephone jack. You’ll connect the spare charger to AC power
only. For more installation information,please see INSTALLATION in this
User’s Manual.
About Caller Identification (Caller ID)
This product has a Caller ID with Call Waiting feature that works with
service from your local phone service provider.
Caller ID with Call Waiting lets you see who’s calling before you answer
the phone,even when you’re on another call.
You may need to change your phone service to use this feature. Contact
your phone service provider if:
•You have both Caller ID and Call Waiting,but as separate services
(you may need combined service)
•You have only Caller ID service,or only Call Waiting ser vice
•You don’t subscribe to any Caller ID or Call Waiting services.
You can use this product with regular Caller ID service,and you can use
this product’s other features without subscribing to either Caller ID or
combined Caller ID with Call Waiting service.
There are fees for Caller ID services,and they may not be available in
all areas.
This product can provide information only if both you and the caller are
in areas offering Caller ID service,and if both telephone companies use
compatible equipment.
About Call History
This phone assigns each incoming call a number from 1 to 25. The most
recent call will have the lowest number. When the memory is full,the
oldest call information is deleted to make room for new incoming call
information.
If you answer a call before call information appears on the screen,it will
not be in the call history.
1
INSTALLATION
Base Installation
NOTE: Install the base unit and spare handset charger away from
electronic equipment, such as personal computers, television sets or
microwave ovens. Avoid excessive heat, cold, dust or moisture.
1Connect the power cord to the base and an electrical outlet
not controlled by a wall switch.
Modular
telephone
jack
2Connect the
telephone
line cord.
Standard
electrical
outlet
Use only the power cord supplied with this product.
If you need a replacement,call 1 800 222–3111.
3Install the handset battery.
Use only AT&T Battery 2422, SKU# 23402.
a) Remove battery
compartment
cover by pressing
on indentation
and sliding
downward.
2
b) Plug the battery
pack connector
into handset.
Place the battery
pack and wires in
the compartment.
c) Replace cover by
sliding it on its
track up over
battery case until
it snaps firmly
into place.
4Charge the handset battery.
•Place the handset in the base (or the spare charger).
•Charge the battery at least 12 hours. After the fir st charge,the
battery will charge in eight hours.
5Check for dial tone.
•After the batteries are charged,lift the handset and press P;
you should hear a dial tone.
Spare Charger Installation
1Connect the power cord attached
to the spare charger to an
electrical outlet not controlled by a
wall switch.
2Follow Steps 3–5 in “Base
Installation.”
Belt Clip
Attach belt clip to
the cordless
handset (optional).
a) Slide down
into grooves
to attach.
INSTALLA TION
b) Push up
and away
to remove.
Headset
You can use this telephone hands-free
when you install any AT&T 2.5 mm
headset (purchased separately).
Plug the headset into the jack located
on the right side of the handset
(under the small rubber flap). Do not
force the connection,but make sure
the plug fits securely.
3
FEATURE SETUP
Feature Setup Menu
NOTE: When you follow the directions to “Clear Message Waiting”or
“Set Dial Mode”you change settings for BOTH handsets. All other
features must be set separately at each handset.
Press S to enter the Feature Setup menu. Use < or > to choose
features,then press S to save your choice.
Press to return to the previous menu item.
NOTE: If you wait more than 20 seconds without pressing a key, the
handset returns to the standby screen.
Handset Volume
Adjusting handset volume will not affect the volume of what the other
party hears. Default setting is 2. You can also adjust volume during a
conversation by pressing < or >. You will hear a beep at each step up or
down. You will not hear a beep at the highest volume setting.
1Press S. The screen displays
>CALL LOG
PHONEBOOK
2Press < until the screen displays
3Press S. The screen displays
4Use the keypad to enter a volume setting (0 – 7)
— OR —
Press < or > to display desired setting.
5Press S to save displayed setting. You will hear a
confirmation tone.
>HANDSET VOLUME
RING VOLUME
>HANDSET VOLUME
4
FEATURE SETUP
Ring Volume
Adjust the volume of the handset ringer. Setting volume to 0 tur ns the
ringer off. Default setting is 6.
1Press S.
2Press < until the screen displays
>RING VOLUME
RING PATTERN
3Press S. The screen displays
4Use the keypad to enter a volume setting (0 – 6)
— OR —
Press < or > to hear ring volumes.
5Press S to save desired setting.
>RING VOLUME
Ring Pattern
The external ring pattern sets which ringer you hear when you have an
outside call. The internal ring pattern sets which ringer you hear when you
have an intercom call from the other handset. External ring patter n default
setting is 0;inter nal ring patter n default setting is 1.
1Press S.
2Press < until the screen displays
3Press S.
4Press > then S to set EXTERNAL
or INTERNAL.
>RING PATTERN
AUTO ANSWER
EXTERNAL
INTERNAL
5Use the keypad to enter a ring pattern selection (0 – 9)
— OR —
Press < or > to display desired setting. A sample of the displayed
setting is played briefly.
6Press S to save displayed setting. You will hear a
confirmation tone.
7Press to exit ring pattern setup.
5
FEATURE SETUP
Auto Answer
When this feature is on,an incoming call is connected when you lift the
handset from the base or the charger (you don’t have to press P). If
the handset is not in the base or charger, you do have to press P to
answer a call,regardless of the setting. The default setting is OFF.
1Press S.
2Press < until the screen displays
>AUTO ANSWER
KEY CLICK
3Press S. The screen displays
4Press > to tur n ON
— OR —
Press < to turn OFF.
5Press S to save the displayed setting.
6Press to exit Auto Answer setup.
AUTO ANSWER
OFF
Key Click
When this feature is on,each key press makes a sound,except when the
keypad is locked. Default setting is ON.
1Press S.
2Press < until the screen displays
3Press S. The screen displays
4Press < or > to display ON or OFF.
5Press S to save the displayed setting.
>KEY CLICK
KEY LOCK
KEY CLICK
ON
6
FEATURE SETUP
Key Lock
When this feature is on,the keypad cannot be used to dial calls. You can
still answer calls,but when the call is ended,the keypad lock is reactivated.
The key lock icon is displayed on the screen when this feature is activated.
The default setting is OFF.
NOTE: To make an emergency call when the keypad is locked, press
P then 911. When the call is ended, the keypad lock is disabled.
1Press S.
2Press < until the screen displays
>KEY LOCK
HANDSET NAME
3Press S. The screen displays
4Press < or > to display ON or OFF.
5Press S to save the displayed setting.
KEY LOCK
OFF
Disable Key Lock
When the keypad is locked,press S, <,S to turn of f the lock.
Handset Name
You can customize the handset to display a name or word of your choice
in place of the READY standby screen. The default setting is READY.
1Press S.
2Press < until the screen displays
3Press S. The screen displays
4Use the chart on page 13 to enter a handset name.
5Press S to save the displayed name.
>HANDSET NAME
LANGUAGE
NAME
7
FEATURE SETUP
Language Setting
You can set each handset so the display appears in English or Spanish. The
default setting is ENGLISH.
1Press S.
2Press < until the screen displays
>LANGUAGE
CLEAR MSG WAIT
3Press S. The screen displays
4Press < or > to select a language.
5Press S to save the displayed setting.
>LANGUAGE
ENGLISH
Clear Message Waiting
If you subscribe to telephone company voice mail,and the message waiting
indicator remains on even after you have reviewed all messages,follow the
directions below to turn off the indicator.
NOTE: These steps will clear the message waiting indicator for BOTH
handsets.
1Press S.
2Press < until the screen displays
3Press S. The screen displays
4Press S to confir m
— OR —
Press to exit without clearing.
>CLEAR MSG WAIT
DIAL METHOD
CLEAR MSG WAIT
CONFIRM?
8
FEATURE SETUP
Set Dial Mode
NOTE: When you change the dial mode setting, BOTH handsets are
affected.
This phone comes set for touch tone (DTMF) dialing. If you have dial pulse
(rotary) service, set the dial mode to PULSE.
1Press S.
2Press < until the screen displays
>DIAL METHOD
CALL LOG
3Press S. The screen displays
4Press < or > to display DTMF or PULSE.
5Press S to save displayed setting.
>DIAL METHOD
DTMF
9
TELEPHONE OPERATION
Making a Call
1 Press P,then
dial the number
— OR —
Dial the number,
then press P.
2 Press P again
to end the call.
Answering a Call
1 Press P to
answer a call.
2 Press P again
to end the call.
NOTE: If you have
the Auto Answer
feature turned on,
you can answer a
call by lifting the
handset from the
base or charger.
Call Timer
The screen displays a
timer and whether
the call is external or
internal (intercom).
Flash/Call Waiting
1 Press F to
connect to the
new call when
you receive a
call-waiting signal.
2 Press F again
to return to the
original call.
NOTE: Use F to
access other phone
company subscriber
services, as described
by your provider.
Intercom
1 Signal one handset
from the other by
pressing I.
2 To answer,press
P on the
second handset.
Redial
1 Press R
before pressing
P to call
the last number
(up to 24 digits)
dialed from either
handset.
2 Press P to
end the call.
10
TELEPHONE OPERATION
Page/Handset Locator
Page the handsets from the base
by pressing L. The
handsets will sound a repeating tone.
Cancel the page by pressing any
key on the handset,or wait 60
seconds.
Indicates handset
charging
Temporary Tone Dialing
If you have dial pulse (rotary) service,you can change from dial pulse to
touch tone dialing during a call.
1Make the call,and wait until it is connected.
2Press S then #. Keys pressed after this send touch tone signals.
3After you hang up,the phone automatically returns to dial pulse
(rotary) service.
Transferring a Call
You can transfer a call from one handset to the other and announce the caller.
1Press I (your call is put on hold) to signal the second
handset.
2At the second handset,press P to take the call.
3When someone answers at the second handset,you can announce
the call. Then place the first handset in the base or charger,or
press P. The call is now connected with the second handset.
Indicates
handset
in use
Forwarding a Call
You can forward the call to the second handset without announcing the caller.
1Press I (your call is put on hold), then press P. The
call is sent to the second handset,and disconnected at the fir st.
2At the second handset,the screen displays any Caller ID
information available for this call. Press P to take the call.
3If the second handset does not pick up the call,it’s sent back to
the first handset. The first handset screen displays CALL BACK.
4Press P to reconnect the first handset to the call
— OR —
The call is automatically reconnected to the first handset in
30 seconds.
11
TELEPHONE OPERATION
Conference Calling
1If one handset is already on a call,you can connect the second
handset to the call by pressing P.
2Disconnect either or both handsets by pressing P.
Mute
1During a telephone conversation,mute the handset microphone by
pressing . The other party
will by unable to hear anything on your
end. The screen displays
You will hear a reminder tone while the handset is muted. The
other party will not hear this tone.
2To return to two-way conversation,press again.
MIC MUTE
12
TELEPHONE PHONE BOOK
This telephone can store up to 20 telephone numbers and names. Stor ing
a number and name in one handset automatically stores it in both.
Storing a Number and Name in Phone Book
1Press S.
2Press < until the screen displays
3Press S.
4Press < to select STORE. The screen
displays
5Press S.
6Enter the telephone number (up to 24 digits).Press REDIAL/PAUSE
to store a pause in the dialing sequence.
7Press S.
8Enter a name connected with this number,using the chart below.
9Press S.
10Begin at Step 4 to enter another telephone number and name
— OR —
Press to exit.
>PHONEBOOK
HANDSET VOLUME
>
STORE
RECALL
Presses
Dial Key123456789
1 space1
2ABC2abc
3DEF3def
4GHI4ghi
5JKL5jkl
6MNO6mno
7PQRS7pqrs
8TUV8tuv
9WXYZ9wx y z
00
**?!/()
##’,-.&
13
TELEPHONE PHONE BOOK
Dialing a Number in Phone Book
1Press m.
2Enter the first letter of the stored name,then scroll using < or >
— OR —
Press < or > to scroll through memory locations.
3Press P to dial the displayed number.
Editing a Number/Name in Phone Book
1Press m.
2Press < or > to scroll through memory locations. Press S
to enter edit number mode.
3Press to erase a digit
— OR —
Press and hold to delete entire telephone number.
4Press S to store number cor rection,and enter edit name
mode.
5Press to erase a character
— OR —
Press and hold to delete entire name.
6Press S to confir m the change. You will hear a confirmation
tone.
Deleting a Number/Name in Phone Book
1Press m.
2Press < or > to scroll through phone book.
3Press to delete the displayed name/number entry.
14
Caller’s
name
Caller’s
telephone
number
CALLER ID OPERATION
HEADLINE RIGHT
HEADLINE R-SUB
Ringer
off
NOTE: Caller ID information is stored in both handsets. Removing a
call record from one handset also removes it from the other.
New
call
Date of
call
Time of
call
Key lock
activated
Position
of call in
call history
Battery needs
charging
Reviewing Call History
1Press S twice. The screen displays the most recent call in
call history (call 1 is the most recent call).
2Press < or > to scroll through call history.
Removing Call Records
Removing a Specific Call Record
1Press S twice. The screen displays the most recent call in
call history (call 1 is the most recent call).
2Press < or > to scroll through call history.
3Press and release to delete the displayed call record.
Removing All Call Records
1Press S twice.
2Press and hold . The screen displays DELETE ALL?
3Press S to delete all call records
— OR —
Press to exit without deleting.
15
CALLER ID OPERATION17BATTERIES
Storing a Call Record in Phone Book
You can store a number received by Caller ID in the telephone phone book.
1Press S twice. The screen displays the most recent call in
call history (call 1 is the most recent call).
2Press < or > to scroll through call history.
3Press S to store displayed number in phone book.
NOTE: A confirmation will sound when the number is stored.
Display Dial
Press P to dial a number displayed in call history.
Dialing Options
While a call history record is displayed,press R until the screen
displays the number the way you want to dial it.
For example: 1–908–555–1212
908–555–1212
1–555–1212
555–1212
The number of dialing options available for each call displayed depends
on the format of the original call.
16
Battery Life
Battery life depends on how far the handset is from the base,and other
environmental conditions.
NOTE: For optimum performance, charge your handset on the base or
charger every night.
Charge the Handset Battery Pack
•This battery should remain charged for up to three days. A fully
charged battery provides an average talk time of about five hours.
•The battery pack needs charging when:
– The battery icon () flashes,
– A warning tone sounds,or
– The screen displays LOW BATTERY when idle.
•Place the handset in the base or charger so the CHARGING light goes
on. The battery pack is typically charged in eight hours. For best
results,the initial charge should be 12 hours.
•You can keep the battery fully charged by returning the handset to the
base or charger after each use.
•If you repeatedly get a low battery indicator,even after eight hour s of
charging,the batter y should be replaced. Use only AT&T Battery 2422,
SKU# 23402.
CAUTION: Charge the battery provided with or identified for use
with this product only in accordance with the instructions and
limitations specified in the User’s Manual,Part 1.
BATTERIES
Replace the Handset Battery Pack
1Install the handset battery.
Use only AT&T Battery 2422, SKU# 23402.
2Charge the handset battery.
•Place the handset in the base or charger.
•Charge the battery for at least 12 hours. After the first charge,
the battery will charge in eight hours.
18
a) Remove battery
compartment
cover by pressing
on indentation
and sliding
downward.
b) Plug the battery
pack connector
into handset.
Place the battery
pack and wires in
the compartment.
c) Replace cover by
sliding it on its
track up over
battery case until
it snaps firmly
into place.
IN CASE OF DIFFICULTY
HEADLINE RIGHT
HEADLINE R-SUB
If you have difficulty operating this phone,tr y the suggestions below.
For Customer Service,visit our website at www.telephones.att.com or call
1 800 222–3111. Please retain your r eceipt as your proof of pur chase.
If the phone does not work at all, check these items first:
•Make sure the power cord is plugged into the base and an electrical
outlet not controlled by a wall switch.
•Make sure the telephone line cord is plugged firmly into the base unit
and the telephone jack.
•Make sure the battery pack is installed correctly.
•If the screen displays LOW BATTERY,place the handset in the base or
charger and charge for at least eight hours.
•If the battery does not charge after eight hours,replace it with AT&T
Battery 2422,SKU# 23402.
If the above suggestions do not solve the problem,try re-initializing the
handset and base (see “To re-initialize the handset and base”below).
If you have no dial tone:
Check all the previous suggestions. If you still do not hear a dial tone,
disconnect the phone and try another phone in the same jack. If there is
no dial tone on that phone either,the problem is probably in your wiring
or local service.
If you hear a two-beep signal when you try to use the handset:
•The handset and base are not communicating properly. You might be
out of range. Move closer to the base and try again.
•If moving closer to the base does not help,follow the directions below
to re-initialize the handset and base.
To re-initialize the handset and base:
1Disconnect the power to the base.
2Remove the handset batter y pack.
3Wait at least 15 seconds.
4Insert the handset battery pack.
5Connect the power to the base.
6Put the handset in the base to re-initialize.
7Wait for handset to display READY (or handset name).
19
IN CASE OF DIFFICULTY
If you hear noise or interference when using the phone:
•You may be out of range. Move closer to the base.
•Household appliances plugged into the same circuit as the base can
sometimes cause interference. Try moving the appliance or the base to
another outlet.
•The layout of your home or office may be limiting the operating range.
Try moving the base to another location,preferably on an upper floor.
•Using the handset near household appliances (microwaves,computers,
televisions,stereos, etc.) can sometimes cause interference. Move away
from appliances while using the handset.
If the phone does not ring when you receive a call:
•Make sure the ringer is on.
•Make sure the telephone line cord is connected firmly to the base and
the telephone jack.
•Make sure the AC adapter is plugged firmly into an electrical outlet not
controlled by a wall switch.
•You might be too far from the base;move closer.
•You might have too many extension phones on your telephone line to
allow all of them to ring. Try unplugging some of them.
If your telephone misdials:
•If you have dial pulse (rotary) service,you’ll need to set the dial mode
to PULSE. Follow the instructions under “Set Dial Mode”in the
FEATURE SETUP section of this manual.
•If you have touch tone service and you hear clicks while you are dialing,
you’ll need to set the dial mode to DTMF. Follow the instructions under
“Set Dial Mode”in the FEATURE SETUP section of this manual.
If the caller’s name or phone number is not displayed:
•Make sure you subscribe to a Caller ID service from your local
telephone company.
•Make sure the battery is charged.
•Caller ID service might not work when the phone is connected to a
Private Branch Exchange (PBX).
If the caller’s name or phone number is not displayed during
Call Waiting:
•You should call your service provider to confirm that you subscribe to
a combined Caller ID with Call Waiting service.
•Caller ID information received during Call Waiting is displayed only on
the handset that is in use. The information is stored in the Caller ID log
on both handsets.