Atec Expandable User Manual

Expandable PIM Analyzer for
Manufacturing and Laboratory.
One Master Control Unit can control up
to 4 different RF Units.
3 Measurement Modes: PIM Analyzer,
RF Units measure forward & reverse
PIM (2-port).
Measures Intermodulation products
IM3, IM5 IM7, IM9, IM11 and IM13.
Information Technology Solutions
Passive Intermodulation (PIM) analyzers measure the amount of unwanted intermodulation signals generated by passive components. Increasing demand for wireless data bandwidth requires networks that operate optimally. Leading global wireless carriers use only low PIM components to guarantee best possible quality of their networks. Since PIM is detrimental to both, network performance and capacity, low PIM components are vital to achieve this goal.
PIM is caused by RF components that show non-linear frequency behavior. Reducing PIM to a minimum must be the ultimate goal for manufacturers of RF components.
RF Components that may cause PIM:
Cables Connectors Antennas Attenuators, Loads Surge Protectors Filter, Diplexer, Duplexer Combiner, Splitter, Coupler
AWT’s Expandable PIM Analyzers grow with widening manufacturing requirements. The Main Control Unit can handle up to four RF Units with different frequency bands. To minimize expenses, customers can choose to start with only one basic frequency band and install additional RF Units later when needed. There is no need to send units back to the factory for the upgrade; additional RF Units can be installed in the field.
Whether growing with demand, or offering greatest
flexibility with four frequency bands, AWT’s
Expandable PIM Analyzers are a cost efficient solution for manufacturing and laboratory.
RF & M IC RO W AVE TE CH NO LOG Y
AWT-Global provides advanced telecommunication technology products and analyzers for a variety of RF and Microwave applications.
EX PA NDABL E PI M AN AL YZ ERS
Production testing requires fast and highly reliable PIM analyzers. As the spectrum of manufactured products widens, PIM analysis may have to be performed on additional frequencies. Our Expandable PIM Analyzer is can be equipped with one to four different RF Units.
PIM ANALYZ ERS FOR PRODU CTION
Production analyzers have to perform reliably 24 /7. Besides Expandable PIM Analyzers for up to 4 frequency bands, AWT - Global offers also Single and Dual band analyzers.
Expandable PIM Analyzer
A
A
A
W
W
W
T
T
T
G
G
G
l
l
l
o
o
o
b
b
b
a
a
a
l
l
l
Advanced Microwave Technology
Data sheet is subject to change without further notice
A
A
A
W
W
W
T
T
T
G
G
G
l
l
l
o
o
o
b
b
b
a
a
a
l
l
l
Advanced Microwave Technology
Model Number / Type
Tx Frequency (MHz)
Rx Frequency (MHz)
Master Control Unit (required, controls up to 4 RF Units)
All
All
RF Units
TETRA 400
390 ~ 400
380 ~ 384
E-TETRA400
420 ~ 430
410 ~ 412
LTE700-U
730 ~ 759
776 ~ 788
LTE700-L
728 ~ 759
698 ~ 716
AMPS/CDMA
869 ~ 896
824 ~ 851
GSM900
935 ~ 960
890 ~ 915
LTE-JP1500
1488 ~ 1520
1456 ~ 1480
DCS/GSM1800
1805 ~ 1880
1710 ~ 1785
PCS1900
1930 ~ 1990
1850 ~ 1910
AWS
2010 ~ 2155
1710 ~ 1755
TD-SCDMA(2000)
2010 ~ 2025
1900 ~ 1920
UMTS/W-CDMA
2110 ~ 2170
1920 ~ 1980
W-CDMA-JP
2150 ~ 2170
2110 ~ 2140
IMT-E(2600)
2620 ~ 2690
2500 ~ 2570
WiBro-KR
2110 ~ 2170 2300 ~ 2390
1910 ~ 1990
Accessories
Opt. 2
Accessory Kit: (2) low PIM cables 3m / 10ft, (1) low PIM cable 1m / 3ft, low PIM load 100W, adapters, torque wrench with hard carry case
Opt. 3
Low PIM Load 100W, < 165 dBc @ 2* 43W, DIN 7/16 (f)
Opt. 4
PIM Source: Generator with preset PIM value. Quick indication and system test.
PR ODUCT Q UALITY
AWT is committed to providing our customers with products meeting the highest quality standards. All AWT products undergo thorough quality checks and are ISO 9001 and ISO 14001 certified.
PR ODUCT DELIV ER Y
Delivery time for Expandable PIM Analyzers is typically 4 – 6 weeks ARO.
MORE INFORMATI ON
For more information about any of our products or services please visit our Web site: www.awt-global.com or contact one of our sales offices.
Transmitter
Carrier Power
+20 to +44 dBm (46 dBm optional)
Power Accuracy
+/- 0.35 dB
Frequency Accuracy
200 ppm
Reverse Pwr. Protection
+43 dBm for 5 sec
Dimensions / Weight / Environment / Electrical
Dimensions
Control Unit RF Units (exc. E-GSM) RF Units E-GSM
483 x 305 x 500 (mm) 483 x 667 x 143 (mm) 483 x 756 x 143 (mm)
Weight
Control Unit RF Units
11.7 kg 25 – 28 kg
Temperature
-10 °C to +40 °C
Humidity
80%, RH (non condensing)
Protection
IP20
AC Power
100 to 240V 50/60 Hz
Power Consumption
Control Unit RF Units
88 Watts (VA) 700 Watts (VA) max
Models / Types
Specifications
Receiver
Reverse IM @ 2x43dBm Forward IM @ 2x43dBm
-129 dBm / -172 dBc typ.
-125 dBm / -168 dBc typ.
Noise Floor
-140 dBm (300 Hz BW)
Dynamic Range (typical)
> 96 dB (ref: -70 dBm)
Reverse Power Protection
+43 dBm for 5 sec Operational Input Power
-40 dBm RMS
Max Input Power
-10 dBm
Measurement Accuracy
+/- 0.2 dB @ 2 x 43 dBm
SALE S OFF ICES
AWT-Global New Jersey
117 Grand Avenue Hackettstown, New Jersey 07054 USA p: +1 (973) 321-3423
e: sales@awt-global.com
AWT-Global Nevada
11309 Asilo Bianco Avenue Las Vegas, Nevada 89138 USA p: +1 (702) 358-0290 e: thomas.lee@awt-global.com
Data sheet is subject to change without further notice
Loading...