Atec Empower-2170 User Manual

Parameter

Symbol

Min

Typ

Max

Unit

Operating Frequency

1000

3000

MHz

Power Output CW

(Note 1)

SAT

1000

Watt

Power Output @ 1dB Gain Compression

(Note 2)

1dB

500

Watt

Power Gain @ 1dB Gain Compression

1dB

Input Power for Rated P

SAT

PIN 0

dBm

Input Power Range

-3.0 +3.0

dBm

Gain Flatness / Leveled ALC

∆G

±3.5/±1.0

Gain Adjustment Range

VVA

Input Return Loss

S11

-10

Noise Figure @ maximum gain

Third Order Intercept Point 2-Tone @ 54dBm/Tone, 1MHz Spacing

Harmonics @ P

= 1000W

(without Harmonic Suppression Filters)

2nd

-20

3rd

-10

Spurious Signals

Spur

-60

dBc

Operating Voltage – (single Ф)

VAC

180

220

260

Volt

Operating Voltage – (3 Ф)

VAC 208

Volt

Power Consumption @ 1000W CW

5000

Watt

Parameter

Value

Units

Dimensions W x H x D

17.5 x 8.75 x 22

Inc

Weight (Without Harmonic Suppression Filters)

lb.

Input: Type-N, Female

Output: Type-7/16-DIN, Female (optional Type-SC, Female)

RF Sample

Type-SMA, Female

Blanking Input

Type-BNC, Female

Cooling

Built in forced-air cooling system

Solid State Broadband High Power Amplifier

2170 – BBS4A6AUT

1000 - 3000 MHz / 1000 Watts

The BBS4A6AUT (SKU 2170) is suitable for multi-octave bandwidth high power CW, modulated, and pulse applications. This amplifier utilizes high power LDMOS devices that provide wide frequency response, high gain, high peak power capability, and low distortions. Exceptional performance, longterm reliability and high efficiency are achieved by employing advanced broadband RF matching networks and combining techniques, EMI/RFI filters, and all qualified components. The amplifier is constructed within one single 5RU drawer including the forced air-cooling. The system comes standard to operate from 180-260VAC single phase or c an be ordered optionally with a three phase AC supply.

The amplifier includes a built in control and monitoring system, with protection functions which preserve high availability. Remote management and diagnostics are via an embedded web server allowing network managed site status and control simply by connecting the unit’s Ethernet port to a LAN. Using a web browser and the unit’s IP address (IPV4, IPV6) allows ease of access with the benefit of multilevel security. The control system core supports hardware encryption, runs an embedded OS (Linux), has a built-in non-volatile memory for event recording, and factory setup recovery features. The extended memory option allows storage of control parameters and event logs.

Empower RF’s ISO9001 Quality Assurance Program assures consistent performance and the highest reliability.

 Solid-state linear design  Suitable for CW, AM, FM and pulse (Consult factory for other modulation types)  Compact Modular design  50 ohm input/output impedance  Built in Control, Monitoring and Protection functions  High reliability and ruggedness

ELECTRICAL SPECIFICATIONS over temperature conditions (-10 to +50ºC)

OUT

Notes: 1. CW measurement performed in MGC Mode (Manual Gain Control) 2 .P1dB measurement performed with CCDF Method, IS-95, 1MHz BW.

MECHANICAL SPECIFICATIONS

RF Connectors Input/Output

316 W. Florence Ave. Inglewood, CA 90301

Ph. 1 (310) 412-8100

Fax. 1 (310) 412-9232

IP3 +64 dBm

dBc

www.EmpowerRF.com

Stock No. 2170

NPI Rev 1.1 / 08-02-2013

Parameter

Symbol

Min

Typ

Max

Unit

Operating Ambient Temperature

-10 +50

°C

Non-operating Temperature

STG

-40 +85

°C

Relative Humidity (no n-condensing)

Shock / Vibration - MIL-STD-810F Shock Method 516.5, Vibration Method 514.5

Parameter

Specifications

Unit

Input Overdrive

+10 dBm

Max

At 3:1 – PA backs-off output power to a safe operating level – no

system shutdown, “On Air” ti m e is maximiz ed

Thermal – Graceful Degradation

Ambient 50ºC

Min

Default Data Recovery

Factory Default Calibration Recovery

Function

Utility

Connector

Ethernet

Network management of device / web interface

RJ45

USB

Mass storage / Expansion Bus

USB 1.x/2.0 compatible

RS-232 (default) RS-422 (optional)

Serial management of device / local operator access

D-Sub 9-position Male

Pin #

Description

Specifications

FWD TP

Forward detected power (analog voltage: 0-5 Volt)

REV TP

Reverse detected power (analog voltage: 0-5 Volt)

Summary Fault: Active TTL Logic Low (≤0.7V) (Internally Pulled-High)

Gain control/Monitor: Analog Voltage Range 0-5V Gain Control: 0V= Max. Attenuator, 5V= Min. Attenuator

Amplifier Disable: TTL Logic Low (≤0.7V) (Internally Pulled-High)

Aux P/S TP

+12.0VDC ±2V (resettable 0.5amp fuse)

Main P/S TP

+44.0VDC ±4.8V (resettable 0.5amp fuse)

GND

Ground

Open drain control