Power Output @ 1dB Gain Compression
(Note 2)
Power Gain @ 1dB Gain Compression
Input Power for Rated P
SAT
Gain Flatness / Leveled ALC
Noise Figure @ maximum gain
Third Order Intercept Point
2-Tone @ 54dBm/Tone, 1MHz Spacing
= 1000W
(without Harmonic Suppression Filters)
Operating Voltage – (single Ф)
Operating Voltage – (3 Ф)
Power Consumption @ 1000W CW
Weight (Without Harmonic Suppression Filters)
Input: Type-N, Female
Output: Type-7/16-DIN, Female (optional Type-SC, Female)
Built in forced-air cooling system
Solid State Broadband High Power Amplifier
2066 – BBS3K4AUT
500 – 1000 MHz / 1000 Watts
The BBS3K4AUT (SKU 2066) is suitable for octave bandwidth high power
CW, modulated, and pulse applications. This amplifier utilizes high power
LDMOS devices that provide wide frequency response, high gain, high peak
power capability, and low distortions. Exceptional performance, long-term
reliability and high efficiency are achieved by employing advanced broadband
RF matching networks and combining techniques, EMI/RFI filters, and all
qualified components. The amplifier and optional switch filter bank are
constructed within one single 5RU drawer including the forced air-cooling.
The system comes standard to operate from 180-260VAC single phase or
optionally can be ordered with a three phase AC supply.
The amplifier includes a built in control and monitoring system, with protection
functions which preserve high availability. Remote management and
diagnostics are via an embedded web server allowing network managed site status and control simply by connecting the unit’s
Ethernet port to a LAN. Using a web browser and the unit’s IP address (IPV4 IPV6) allows ease of access with the benefit of multilevel security. The control system core supports hardware encryption, runs an embedded OS (Linux), has a built-in non-volatile
memory for event recording, and factory setup recovery features. The extended memory option allows storage of control
parameters and event logs.
Empower RF’s ISO9001 Quality Assurance Program assures consistent performance and the highest reliability.
Solid-state linear design
Suitable for CW, AM, FM and pulse (Consult factory for other modulation types)
Compact Modular design
50 ohm input/output impedance
Built in Control, Monitoring and Protection functions
High reliability and ruggedness
Optional harmonic and spurious suppression via internal switched filter bank (quoted separately)
ELECTRICAL SPECIFICATIONS over temperature conditions (-10 to +50ºC)
OUT
Notes: 1. CW measurement performed in MGC Mode (Manual Gain Control).
2. P1dB measurement performed with CCDF method, IS-95, 1MHz BW.
MECHANICAL SPECIFICATIONS
RF Connectors Input/Output
316 W. Florence Ave.
Inglewood, CA 90301
Ph. 1 (310) 412-8100
Fax. 1 (310) 412-9232
IP3 +64 dBm
dBc
www.EmpowerRF.com
Stock No. 2066
D.S. Rev 1.9 / 08-02-2013
Operating Ambient Temperature
Non-operating Temperature
Relative Humidity (no n-condensing)
Shock / Vibration - MIL-STD-810F
Shock Method 516.5, Vibration Method 514.5
At 3:1 – PA backs off output power to a safe operating level – no
system shutdown, “On Air” ti m e is maximiz ed
Thermal – Graceful Degradation
Factory Default Calibration Recovery
Network management of device / web interface
Mass storage / Expansion Bus
RS-232 (default) RS-422 (optional)
Serial management of device / local operator access
Forward detected power (analog voltage: 0 – 5 Volt)
Reverse detected power (analog voltage: 0 – 5 Volt)
Summary Fault: Active TTL Logic Low (≤0.7V)
(Internally Pulled-High)
Gain control/Monitor: Analog Voltage Range 0-5V
Gain Control: 0V= Max. Attenuator, 5V= Min. Attenuator
Amplifier Disable: TTL Logic Low (≤0.7V)
(Internally Pulled-High)
+12.0VDC ±2V (resettable 0.5amp fuse)
+44.0VDC ±4.8V (resettable 0.5amp fuse)
Site management utility (reserved)
Site management utility (reserved)
Site management utility (reserved)
Digital I/O (configurable)
Site management utility (reserved)
Digital I/O (configurable)
Site management utility (reserved)
Solid State Broadband High Power Amplifier
2066 – BBS3K4AUT
ENVIRONMENTAL CHARACTERISTICS (Qualification Data available for review):
SH / VI
PROTECTIONS:
VSWR Protection
COMMUNICATION INTERFACES:
SYSTEM I/O CONNECTOR – 14-pin
500 – 1000 MHz / 1000 Watts
-
3 Summary Fault
4 VVA control
5 Shutdown
316 W. Florence Ave.
Inglewood, CA 90301
Ph. 1 (310) 412-8100
Fax. 1 (310) 412-9232
www.EmpowerRF.com
Stock No. 2066
D.S. Rev 1.9 / 08-02-2013