Atec EMCPro-PLUS User Manual
KeyTek EMCPro®PLUS
Advanced EMC test system for
compliance testing to 6 IEC/EN standards
Technical Specifications
The newly configured KeyTek EMCPro®PLUS
test system features resident capabilities for EMC
CE Mark compliance testing to 6 IEC/EN standards,
and fully addresses new requirements for a 100 kHz
burst rate per IEC 61000-4-4, Edition 2 (EFT) and 80%
dip per IEC 61000-4-11, Edition 2 (PQF™).
Portable and low cost, the KeyTek EMCPro PLUS
is the answer to manufacturers’ demand for a
mid-range, multi-capability EMC immunity tester.
It’s ideal for companies who require flexibility,
versatility, and the highest test level-to-cost ratio
instrument on the market.
Portable, mid-range EMC
test system
Resident capabilities for
compliance testing to
6 IEC/EN standards
Addresses ANSI/IEEE, ITU,
ETSI & UL standards
Surge testing to 6.6kV with the
combination, telecom, & ring
waves
Monitors surge voltage &
current at the output terminals
Monitors output of the coupling
unit & automatically switches
connections according to
coupling mode
Highest test levels, widest
selection of tests & lowest
in-use costs
Technical Specifications
Model PRO-BASE
EMCPro PLUS Base Unit
System Voltage 90-240VAC, 50/60Hz
INTEGRATED EUT MAINS
COUPLER/DECOUPLER
AC Voltage 1 phase, 50 -
250VAC. 50/60Hz
AC Current 16A max.**
DC Voltage 100VDC max.
DC Current: 10A max.
Frequency 50/60Hz
EUT Connectors Nema, British,
Schuko
CONTROL INTERFACE
Interface RS232 Fiber-optic
SAFETY FEATURES External Interlock for
users
Interlock for CCL
connector
External stop input
ENVIRONMENTAL OPERATING CONDITIONS
Temperature 15°- 40°C
Humidity 10-75%, non-
condensing
Altitude 8000 ft. max.
PHYSICAL
Height 22.9cm (8.7 in)
Width 43.4cm (17.1 in)
Depth 64.8cm (25.5 in)
Weight 39kg (85 lbs.)
CE MARKING Safety and EMC
Directives
Upgradable as standards
change
Analyze • Detect • Measure • Control
TM
Model PRO-ESD
ESD per IEC 61000-4-2 and EN 61000-4-2
Trigger Modes One shot manual, multi-shot tripod
Repetition Rate Single shot, 1pps or 20pps
Air Discharge Voltage 500V - 8.8kV ±10%
Contact Discharge Voltage 500V - 4.4kV ±10%
Discharge Capacitor 150pF ±10%
Discharge Resistance 330Ω ±10%
Charging Resistance 50MΩ- 100MΩ
Polarity Front panel or software controlled
Shot Counter 1 - 999 discharges
Energy Storage 5.8mJ @ 8.8kV
Model PRO-EFT
EFT per IEC 61000-4-4 Edition 2, EN 61000-4-4 and ANSI C62.41
Voltage Waveform 5/50ns ±30%
Peak Voltage 250V - 4.4kV ±5%
Burst Period 300ms ±10%
Burst Duration 15ms ±20%, for pulse frequencies uo to 5kHz, 0.75ms
above 5kHz
Frequency 1-100kHz, in 0.5kHz steps, ±10%
DC Blocking Capacitor 10nF (internal)
Options Model CM-3CD-16/32: 16 or 32 Amp, 3 phase EFT &
surge coupler/decoupler
Model CM-CCL: Capacitive coupling clamp
Model CM-CCLC: Coupling clamp cover
Model EFT-ATTN: EFT attenuator for oscilloscope
monitoring
Model PRO-SURGE
Surge for compliant testing per IEC 61000-4-5, EN 61000-4-5, ANSI C62.41 Category B and
UL 1449
Voltage Waveform 1.2/50µs
Peak Voltage 250V - 6.6kV ±5%, 12Ω mode
250V - 6.0kV ±5%, 2Ω mode
Peak Current 125A - 3.3kA ±10%
Additional 10Ω Resistor Software selectable
Repetition Rate Up to 4 per minute
Open-circuit Voltage Front time: 1.2µs ±30%
Duration: 50 µs ±20%
Undershoot: ≤ 30%
Short-circuit Current Front time: 8.0µs ±20%
*
Duration
Undershoot ≤ 30%
Line sync accuracy ±15%, 50 - 277VAC
Options Model CM-3CD-16/32: 16 or 32 Amp, 3 phase EFT
*
Durations are reduced in 12Ω mode and when coupling multiple lines to PE
50µs ±20%
& surge coupler/decoupler
Model CM-I/OCD: External 8 line coupler/decoupler
for I/O signal lines
Model CM-I/OCD-HS: High speed I/OCD option for
testing data rates to >100kHz
1
Model PRO-RING
Ring Wave Surge per ANSI C62.41 Cat. A, B, and UL 864
Voltage Waveform 100kHz damped cosine
Peak Voltage 250 - 6.6kV ±5%
Repetition Rate <4/minute at 6kV, faster at lower voltages
Open-circuit Voltage Rise Time: 0.5µs ±30%
Short-circuit Current Vp/Ip: 12Ω ±3Ωor 30Ω±8Ωsoftware selectable
Options Model CM-3CD-16/32: 16 or 32 Amp, 3 phase EFT
Model PRO-TELECOM
Surge Telecom compliant testing per IEC 61000-4-5, EN 61000-4-5, FCC Part 68, ITU K.17,
K.20, K.21 and ETSI
Voltage Waveform 10/700µs (9/720µs FCC Part 68)
Peak Voltage 250V - 6.6kV ±5%
Peak Current 6.25 - 165A +10/-0%, 40Ωmode
Repetition Rate Up to 4 per minute
Open-circuit Voltage Front time: 7.0µs to 11.7µs
Short-circuit Current Front time: 3.5µs to 6.5µs
Options Model CM-TELCD: External coupler for telecom lines
**
& surge coupler/decoupler
**
Duration: 576µs to 840µs
Duration: 256µs to 384µs
Surge Waveform Monitoring
Lines Monitored Monitors are automatically switched to match
generator coupling mode
Open-circuit Voltage 1000:1 ±10%
Short-circuit 200:1 ±7%
Current Attenuation
Model PRO-HPOWER
Power Frequency Magnetic Field for compliant testing per IEC 61000-4-8 and EN 61000-4-8
Field Frequency 50Hz/60Hz
Field Amplitude 0.5 - 4A/m, in 0.25A steps, ±10% (with CM-HCOIL)
up to 100A/m with optional external HPOWER-EXT
AC Source Internal
Resolution 0.25A minimum
Coil Factor 0.65 to 1.00
Coil Resistance 0.05Ω maximum
Options Model CM-HMON: Measurement probe for power
frequency magnetic fields
Model CM-HCOIL: 1m x1m magnetic field coil
Model HPOWER - EXT: External generator for power
frequency magnetic field to 30A/m
**
PRO-TELECOM and PRO-RING can not be installed in same unit.
Loading...