ASUS P2B-IDE User Manual
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
P2B IDE Connectors
Primary IDE Connector
PIN 1
Secondary IDE Connector
NOTE: Orient the red stripe to PIN 1
R
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
IE302
III. INSTALLATION
This insert is to replace page 28 of your P2B manual (Manual 1.03).
6. Universal Serial BUS Ports 1 & 2 (Two 4-pin Female)
Two USB ports are available for connecting USB devices.
USB 1
Universal Serial Bus (USB) 2
7. Primary / Secondary IDE Connectors (Two 40-1pin IDE)
These connectors support the provided IDE hard disk ribbon cable. After connecting the single end to the board, connect the two plugs at the other end to your hard
disk(s). If you install two hard disks, you must configure the second drive to Slave
mode by setting its jumper accordingly. Refer to the documentation of your hard
disk for the jumper settings. BIOS now supports SCSI device or IDE CD-ROM
bootup (see “HDD Sequence SCSI/IDE First” & “Boot Sequence” in the BIOS
Features Setup of the BIOS SOFTWARE) (Pin 20 is removed to prevent in-
serting in the wrong orientation when using ribbon cables with pin 20 plugged).
TIP: You may configure two hard disks to be both Masters using one ribbon
cable on the primary IDE connector and another ribbon cable on the secondary
IDE connector. You may install one operating system on an IDE drive and another on a SCSI drive and select the boot disk through BIOS Features Setup.
Connectors
III. INSTALLATION
IE302
III. INSTALLATION
This insert is to replace page 28 of your P2B manual (Manual 1.03).
6. Universal Serial BUS Ports 1 & 2 (Two 4-pin Female)
Two USB ports are available for connecting USB devices.
USB 1
Universal Serial Bus (USB) 2
7. Primary / Secondary IDE Connectors (Two 40-1pin IDE)
These connectors support the provided IDE hard disk ribbon cable. After connecting the single end to the board, connect the two plugs at the other end to your hard
disk(s). If you install two hard disks, you must configure the second drive to Slave
mode by setting its jumper accordingly. Refer to the documentation of your hard
disk for the jumper settings. BIOS now supports SCSI device or IDE CD-ROM
bootup (see “HDD Sequence SCSI/IDE First” & “Boot Sequence” in the BIOS
Features Setup of the BIOS SOFTWARE) (Pin 20 is removed to prevent in-
serting in the wrong orientation when using ribbon cables with pin 20 plugged).
TIP: You may configure two hard disks to be both Masters using one ribbon
cable on the primary IDE connector and another ribbon cable on the secondary
IDE connector. You may install one operating system on an IDE drive and another on a SCSI drive and select the boot disk through BIOS Features Setup.
Connectors
III. INSTALLATION
R
P2B IDE Connectors
8. IDE Device Activity LED (2-pin IDELED)
This connector supplies power to the cabinet’s IDE device activity LED. Read
and write activity by devices connected to the Primary or Secondary IDE connectors will cause the LED to light up.
IDELED
R
TIP: If the case-mounted LED does not light,
try reversing the 2-pin plug.
P2B IDE Activity LED
ASUS P2B User’s Manual 28
NOTE: Orient the red stripe to PIN 1
PIN 1
Secondary IDE Connector
Primary IDE Connector
8. IDE Device Activity LED (2-pin IDELED)
This connector supplies power to the cabinet’s IDE device activity LED. Read
and write activity by devices connected to the Primary or Secondary IDE connectors will cause the LED to light up.
IDELED
R
TIP: If the case-mounted LED does not light,
try reversing the 2-pin plug.
P2B IDE Activity LED
ASUS P2B User’s Manual 28
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
Loading...