Asus P2300 Manual

AP2300

Dual Pentium® III Server Platform

Hardware Reference Guide

User's Notice

No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. (“ASUS”).

ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT.

Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the product is defaced or missing.

Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners’ benefit, without intent to infringe.

The product name and revision number are both printed on the product itself. Manual revisions are released for each product design represented by the digit before and after the period of the manual revision number. Manual updates are represented by the third digit in the manual revision number.

For previous or updated manuals, BIOS, drivers, or product release information, contact ASUS at http://www.asus.com.tw or through any of the means indicated on the following page.

SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE, AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAYAPPEAR IN THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT.

Copyright © 2000 ASUSTeK COMPUTER INC. All Rights Reserved.

Product Name:	AP2300
Manual Revision:	1.00 E540
Release Date:	June 2000

2	AP2300 Hardware Reference Guide

ASUS Contact Information

ASUSTeK COMPUTER INC. (Asia-Pacific)

Marketing

Address:	150 Li-Te Road, Peitou, Taipei, Taiwan 112
Telephone:	[phone]
Fax:	[phone]
Email:	[e-mail]

Technical Support

MB/Others (Tel):	[phone] (English)
Notebook (Tel):	[phone] (English)
Desktop/Server (Tel):[phone] (English)
Fax:	[phone]
Email:	[e-mail]
WWW:	www.asus.com.tw
FTP:	ftp.asus.com.tw/pub/ASUS

ASUS COMPUTER INTERNATIONAL (America)

Marketing

Address:	6737 Mowry Avenue, Mowry Business Center, Building 2
	Newark, CA 94560, USA
Fax:	[phone]
Email:	[e-mail]

Technical Support

Fax: [phone]

Email: [e-mail]

WWW: www.asus.com

FTP: ftp.asus.com/Pub/ASUS

ASUS COMPUTER GmbH (Europe)

Marketing

Address:	Harkortstr. 25, 40880 Ratingen, BRD, Germany
Fax:	[phone]
Email:	[e-mail] (for marketing requests only)

Technical Support

Hotline:	MB/Others: [phone]
	Notebook: [phone]
Fax:	[phone]

Support (Email): www.asuscom.de/de/support (for online support) WWW: www.asuscom.de

FTP: ftp.asuscom.de/pub/ASUSCOM

AP2300 Hardware Reference Guide

3

Contents

1. Introduction .....................................................................		7
1-1 How this Manual is Organized ..........................................		7
	Symbols .......................................................................	7
1-2	Component Checklist ........................................................	8
	Standard components ..................................................	8
	Optional components ...................................................	8
1-3	Features ............................................................................	9
	Motherboard: ASUS CUR-DLS ....................................	9
	Chassis: AS-30 ............................................................	9
1-4	Safeguards .....................................................................	10
	Operation Safety ........................................................	10
	Tools Required ...........................................................	10
1-5	Electrical Safety ...............................................................	11

2. System Overview ..........................................................		13
2-1	Server Front Side ............................................................	13
2-2	Server Back Side ............................................................	14
2-3	Server Left Side ..............................................................	15

3. Basic Operation .............................................................		16
3-1	Starting the Server ..........................................................	16
3-2	LEDs ...............................................................................	16
3-3	BIOS Setup .....................................................................	16

4. Hardware Setup .............................................................		17
4-1	Opening the Chassis ......................................................	17
	Panel Screws .............................................................	17
	Removing the Right Panel .........................................	17
	Opening the Left Panel ..............................................	18
	Chassis Circulation System .......................................	18
	Fan Modules ..............................................................	18
4-2 Rear Cooling Fan Control Board ....................................		19
	Rear Cooling Fan Control Board Settings .................	19
4-3	Motherboard Placement .................................................	20
	Motherboard Spacers ................................................	20
	Motherboard Screws ..................................................	20
	Chassis Intrusion Connector ......................................	20
	Device Cables ............................................................	21
	Cable Connections ....................................................	21
4-4	Central Processing Unit (CPU) .......................................	22
	Installing S370 CPU ...................................................	22
4-5	Fan Heatsink ...................................................................	23
	Fan Heatsink Attachment ...........................................	23

4	AP2300 Hardware Reference Guide

Contents

4-6	Chassis Intrusion Switch .................................................	25
4-7	Expansion Cards ............................................................	25
4-8	Fixed Storage Devices ....................................................	27
	Floppy Drive and CD-ROM ........................................	27
	Fixed Storage Device Tray ........................................	26
	Fixed Device Bay Cover Clips ...................................	26
	Fixed Device Bay Cover ............................................	26
	Storage Device Spacers ............................................	27
4-9	Five-Tray Hot-Swap Bay .................................................	29
4-10	Three-Tray Hot-Swap Bay ..............................................	28
	Hot-Swap Tray ...........................................................	29
	Hot-Swap Bay ............................................................	29
4-11 Front Cooling Fans .........................................................		30
	Front Cooling Fan Control Board ...............................	31
	Hard Disk Drive Message Board ...............................	31
4-12	SCSI Backplane ..............................................................	32
4-13	SCSI ID Setting ...............................................................	33
4-14	SCSI Termination ............................................................	34
4-15 SMBus Connector ...........................................................		34
4-16	Redundant Power Supply ...............................................	35
	Power Supply Components .......................................	34
	Power Module Rating ................................................	34
	Removing One Power Supply Module .......................	36
	Removing the Entire Power Supply Unit ....................	36
	Power Supply Mounting .............................................	36
	Power Supply Information ..........................................	37
4-17	Standard Power Supply (Optional) .................................	38
	Power Supply Mounting .............................................	38
	Power Supply Information ..........................................	38
4-18	Power Supply Requirement ............................................	40
	Power Supply Requirement Calculation Table ...........	40

5. Appendix ........................................................................		41
5-1	SCSI Cable Limits ...........................................................	41
5-2	Glossary ..........................................................................	42
Index	...................................................................................	43

AP2300 Hardware Reference Guide

5

FCC & DOC COMPLIANCE

Federal Communications Commission Statement

This device complies with FCC Rules Part 15. Operation is subject to the following two conditions:

•This device may not cause harmful interference, and

•This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with manufacturer’s instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•Re-orient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.

•Consult the dealer or an experienced radio/TV technician for help.

WARNING! The use of shielded cables for connection of the monitor to the graphics card is required to assure compliance with FCC regulations. Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

Canadian Department of Communications Statement

This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications.

6	AP2300 Hardware Reference Guide

1. Introduction

You are reading the AP2300 Hardware Reference Guide. This hardware reference guide provides information and procedures on the various components used in this server. Some components shown in this reference guide are optional and may be individually purchased to complete the server. This guide is intended for experienced users and integrators with hardware knowledge of personal computers. You should also read all documentation and manuals included with this server and with your separately purchased components.

• 1-1 How this Manual is Organized

There are only a few sections in this reference guide as follows:

1. Introduction

This section provides general information and features of this server.

2. System Overview

This section provides a brief introduction to each server component.

3. Getting Started

This section provides information on getting started with the server.

4. Hardware Setup

This section provides detailed information on setting up the server.

5. Appendix

This section gives you additional information to help plan your server.

Symbols

To complete certain tasks safely and completely, you should be aware of a few symbols used throughout this guide.

WARNING: Information to prevent injury to yourself when trying to complete a task.

CAUTION: Information to prevent damage to the components when trying to complete a task.

IMPORTANT: Information that MUST be followed in order to complete a task.

NOTE: Tips and information to aid in completing a task.

PHILIP (CROSS) SCREW DRIVER: Tools required to install or remove the components in this server.

STANDARD (FLAT) SCREW DRIVER: Tools required to install or remove the components in this server.

STEP: Actions to complete a task.

Introduction	/Symbols
Introduction
1.	Sections
1.

AP2300 Hardware Reference Guide

7

Checklist

Introduction .1

1.Introduction

•1-2 Component Checklist

If assembling this server by yourself, it is important to prepare all the server components before starting. This will save a great deal of time by not having to hunt down components. The following checklist provides a guideline as to the necessary components for a server.

Standard components

Motherboard:	CUR-DLS
Chassis:	AS-30
Power Supply:	ATX
Processor (CPU):	Pentium® III
Memory Modules:	8, 16, 32, 64, 128, 256, 512MB, 1GB SDRAM
Hard Drive:	Ultra160, Ultra2, Ultra-wide
Floppy Drive:	1.44MB
CD-ROM Drive:	40X/50X
Expansion Cards
SCSI Terminator:	Passive terminator for 68-pin SCSI cables
User’s Manuals:	CD-ROM, motherboard, hardware guide

Optional components

RAID Controller: PCI-DA2200 or DA-3000 RAID controller

S370 CPU Terminator

Rack-mount Rails: AS-30 rail kit

8	AP2300 Hardware Reference Guide

1.Introduction

•1-3 Features

The AP2300 is configured on the ASUS CUR-DLS smart motherboard which uses the ServerSetTM chipset from ServerWorks® , supporting dual Pentium III processors and 133MHz Front Side Bus in order to accelerate even the most complicated server tasks. The following are highlights to this server’s many features. For additional features and details, read the motherboard User’s Manual included with this server package.

Motherboard: ASUS CUR-DLS

•Processor: Dual Intel® Pentium III FC-PGA processors running at 133MHz or 100MHz Front Side Bus.

•Memory: Four 168-pin DIMM sockets for 16MB-4GB PC133 registered SDRAM with ECC support.

•Onboard SCSI (optional): LSI® Ultra160/Ultra2-Wide SCSI controller to support up to 30 SCSI devices on dual channels.

•Onboard LAN: Intel® 82559 Fast-Ethernet LAN controller.

•Onboard VGA: ATI® Rage XL VGA controller with 4MB PC100 SDRAM to support one VGA connector and one DFP (Digital Flat Panel) connector.

•Super Multi-I/O: Two PCI Bus Master IDE Ports with Ultra DMA/33 support, one floppy, two serial COM ports, one parallel port, one PS/2 keyboard, one PS/2 mouse, one RJ-45 LAN port, two USB ports, and one IrDA connector.

•Expansion Slots: Six or seven PCI slots (33 or 66MHz, depending on model), and one ASMC slot for IPMI (Intelligent Platform Management Interface) compliant management solution.

Chassis: AS-30

•Chassis: Tower server chassis with rack-mount rail tracks.

•Backplane: Wide-SCSI backplane board with LVDS support, remote SCSI ID DIP switches and power to support 5 SCSI SCA hard drives.

•Power: ATX 300W redundant power supply with optional standard 400W power supply.

•Device Bays: Support for one 3.5inch floppy device, three 5.25inch devices, five hot-swappable hard disk drives in removable aluminum trays.

1. Introduction 1. Introduction Features

AP2300 Hardware Reference Guide

9

Safeguards

Introduction .1

1.Introduction

•1-4 Safeguards

Observe the following safety instructions any time you are connecting or disconnecting any devices.

Operation Safety

IMPORTANT

• Any operation on this server must be conducted by certified or experienced engineers.

•Before operating your server, carefully read all the manuals included with the server package.

•Before using the server, make sure all cables are correctly connected and the power cables are not damaged. If any damage is detected, contact your dealer as soon as possible.

•To avoid short circuits, keep paper clips, screws, and staples away from connectors, slots, sockets and circuitry.

•Before opening the chassis panels, make sure all power cables are unplugged.

•Avoid dust, humidity, and temperature extremes. Place the server on a stable surface.

•If the power supply is broken, do not try to fix it by yourself. Contact an authorized dealer.

•It is recommanded that you wear gloves when assembling or dissembling the server to protect from cuts and scrapes.

•When the server is powered on, heat sinks and the surfaces of certain IC devices may be hot. Do not touch them. Check whether the fans are functioning properly.

Tools Required

A Phillips (cross) screwdriver and a standard (flat) screwdriver are needed to install or remove the components in this server.

10	AP2300 Hardware Reference Guide

1.Introduction

•1-5 Electrical Safety

IMPORTANT

• Before installing or removing signal cables, ensure that the power cables for the system unit and all attached devices are unplugged.

•To prevent electrical shock hazard, disconnect the power cable from the electrical outlet before relocating the system.

•When adding or removing any additional devices to or from the system, ensure that the power cables for those devices are unplugged before the signal cables are connected. If possible, disconnect all power cables from the existing system before you add a device.

•Use one hand, when possible, to connect or disconnect signal cables to prevent a possible shock from touching two surfaces with different electrical potentials.

CAUTION

This product is equipped with a three-wire power cable and plug for the user’s safety. Use the power cable in conjunction with a properly grounded electrical outlet to avoid electrical shock.

IMPORTANT

Motherboards, adapters, and disk drives are sensitive to static electricity discharge. These devices are wrapped in antistatic bags to prevent this damage. Take the following precautions:

•If you have an antistatic wrist strap available, use it while handling the device.

•Do not remove the device from the antistatic bag until you are ready to install the device in the system unit.

•With the device still in its antistatic bag, touch it to a metal frame of the system.

•Grasp cards and boards by the edges. Hold drives by the frame. Avoid touching the solder joints or pins.

•If you need to lay the device down while it is out of the antistatic bag, lay it on the antistatic bag. Before picking it up again, touch the antistatic bag and the metal frame of the system unit at the same time.

•Handle the devices carefully in order to prevent permanent damage.

Introduction	Safety
Introduction
1.	Electrical
1.

AP2300 Hardware Reference Guide

11

1. Introduction

(This page was intentionally left blank)

Introduction .1

12	AP2300 Hardware Reference Guide

2.System Overview

•2-1 Server Front Side

The front side of the server is provided to show the front exterior components of this server. The chassis is made of strong rust-resistant metal and covered with a protective ivory surfacing.

1

2

3

4

5

6

7

8

9

10

11

12

13

1.Top Panel

2.Power LED

3.ATX Power Button

4.Hard Drive Access LED

5.Floppy Disk Drive

6.CD-ROM Drive

7.Drive Expansion Bay

8.Side Panel Handle

9.Side Panel Screws

10.Metal Door Lock

11.Hot-Swap Trays

12.Hard Drive Fan Module

13.Chassis Stabilizers

Server Front Side

2. Overview

Front Side

AP2300 Hardware Reference Guide

13

Side Back

Overview .2

2.System Overview

•2-2 Server Back Side

1

2

3

4

5

6

7

8

9

10

11

12

1.Top Panel Screws

2.Power Supply Fan

3.AC Power In Connector

4.Alarm Reset Button

5.PS/2 Keyboard, PS/2 Mouse

6.USB Ports 1 and 2, RJ45 Port (LAN)

7.Serial Port COM1

8.Parallel Port

9.Serial Port COM2

10.VGA Connector

11.Rear Fan Module

12.Chassis Stabilizer

Server Back Side

14	AP2300 Hardware Reference Guide