Asrock Z370 Extreme4 Quick Installation Guide

Version 1.1 Published November 2017 Copyright©2017 ASRock INC. All rights reserved.
Copyright Notice:
No part of this documentation may be reproduced, transcribed, transmitted, or translated in any language, in any form or by any means, except duplication of documentation by the purchaser for backup purpose, without written consent of ASRock Inc.
infringe.
Disclaimer:
Specications and information contained in this documentation are furnished for informational use only and subject to change without notice, and should not be constructed as a commitment by ASRock. ASRock assumes no responsibility for any errors or omissions that may appear in this documentation.
With respect to the contents of this documentation, ASRock does not provide warranty of any kind, either expressed or implied, including but not limited to the implied warranties or conditions of merchantability or tness for a particular purpose.
In no event shall ASRock, its directors, ocers, employees, or agents be liable for any indirect, special, incidental, or consequential damages (including damages for loss of prots, loss of business, loss of data, interruption of business and the like), even if ASRock has been advised of the possibility of such damages arising from any defect or error in the documentation or product.
is device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that
may cause undesired operation.
CALIFORNIA, USA ONLY
e Lithium battery adopted on this motherboard contains Perchlorate, a toxic substance controlled in Perchlorate Best Management Practices (BMP) regulations passed by the California Legislature. When you discard the Lithium battery in California, USA, please follow the related regulations in advance. “Perchlorate Material-special handling may apply, see www.dtsc.ca.gov/hazardouswaste/ perchlorate”
ASRock Website: http://www.asrock.com
AUSTRALIA ONLY
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage caused by our goods. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. If you require assistance please call ASRock Tel : +886-2-28965588 ext.123 (Standard International call charges apply)
e terms HDMI™ and HDMI High-Denition Multimedia Interface, and the HDMI logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.
Manufactured under license under U.S. Patent Nos: 5,956,674; 5,974,380; 6,487,535; 7,003,467 & other U.S. and worldwide patents issued & pending. DTS, the Symbol, & DTS and the Symbol together is a registered trademark & DTS Connect, DTS Interactive, DTS Neo:PC are trademarks of DTS, Inc. Product includes soware. © DTS, Inc., All Rights Reserved.
Motherboard Layout
Intel
Z370
DDR 4_A2 (6 4 bit, 28 8-pin mo dule)
DDR 4_A1 (6 4 bit, 28 8-pin mo dule)
DDR 4_B2 (6 4 bit, 28 8-pin mo dule)
DDR 4_B1 (6 4 bit, 28 8-pin mo dule)
ATX12V1
ATXP WR 1
LAN
PCIE2
Top: RJ-45
USB 3.1 Gen1 T: USB3 B: USB4
Top:
Central/Bass
Center :
REAR SPK
Top:
LINE IN
Center :
FRONT
Bottom :
Optica l
SPDIF
Bottom :
MIC IN
PCIE4
HDLED RESET
PLED PWRBTN
PANEL1
1
1
SPK_PLED1
COM1
1
1
HD_AUDIO1
PCIE6
SATA3_2_3
SATA3_0_1
SATA3_A1_ A2
PCIE1
RoHS
6
8
9
10
11
12
13
USB_1_2
1
19
USB_3_4
1
20
USB_5_6
1
18 1726
27
HDMI1
SATA3_4_5
1
5
4
25
14
BIOS_A1
BIOS_B1
BIOS_B_LED1
BIOS
BIOS
BIOS_A_LED1
USB 3.1 Ge n1
T: USB1
B: USB2
PS2
Keybo ard
/Mous e
CMOS
Battery
PCIE3
M2_1
M2_2
CT2
CT2
CT3
CT3
CT4
CT4CT5
T B1
1
23
2
USB3_7 _8
1
1516
CPU_FAN1
7
21
1
TPMS1
PCIE5
USB 3.1 Gen2 T: USB31_TA_1 B: USB31_TC_1
CT1
CT1
CHA_FAN1
Ultra M.2
PCIe Gen3x4
CHA_FAN2
CPU_OPT/ W_PUMP
CHA_FAN3/W_PUMP
3
USB3_5 _6
1
RGB_LED
1
24
CLRMOS1
1
22
Ult ra M.2
PCIe G en3 x4
USB3_TC_1
Purity
Sound 4
TM
Z370 Extreme4
English
1
No. Description
1 ATX 12V Power Connector (ATX12V1)
2 CPU Fan Connector (CPU_FAN1)
3 CPU Fan / Waterpump Fan Connector (CPU_OPT/W_PUMP)
4 2 x 288-pin DDR4 DIMM Slots (DDR4_A1, DDR4_B1)
5 2 x 288-pin DDR4 DIMM Slots (DDR4_A2, DDR4_B2)
6 ATX Power Connector (ATXPWR1)
7 USB 3.1 Gen1 Header (USB3_5_6)
8 USB 3.1 Gen1 Header (USB3_7_8)
9 Front Panel Type C USB 3.1 Gen1 Header (USB3_TC_1)
10 SATA3 Connectors (SATA3_4_5)
11 SATA3 Connectors (SATA3_2_3)
12 SATA3 Connectors (SATA3_0_1)
13 SATA3 Connectors (SATA3_A1_A2)
14 System Panel Header (PANEL1)
15 Power LED and Speaker Header (SPK_PLED1)
16 Chassis Fan / Waterpump Fan Connector (CHA_FAN3/W_PUMP)
17 COM Port Header (COM1)
18 USB 2.0 Header (USB_5_6)
19 USB 2.0 Header (USB_1_2)
20 USB 2.0 Header (USB_3_4)
21 TPM Header (TPMS1)
22 Chassis Fan Connector (CHA_FAN2)
23 underbolt AIC Connector (TB1)
24 RGB LED Header (RGB_LED)
25 Clear CMOS Jumper (CLRMOS1)
26 Front Panel Audio Header (HD_AUDIO1)
27 Chassis Fan Connector (CHA_FAN1)
English
2
I/O Panel
Z370 Extreme4
6
1
2 547
3
15 10131416
12
No. Description No. Description
1 PS/2 Mouse/Keyboard Port (PS2_KB1) 9 Optical SPDIF Out Port
2 D-Sub Port 10 USB 3.1 Gen1 Ports (USB3_34)
3 LAN RJ-45 Port* 11 USB 3.1 Gen2 Type-A Port (USB31_TA_1)
4 Central / Bass (Orange) 12 USB 3.1 Gen2 Type-C Port (USB31_TC_1)
5 Rear Speaker (Black) 13 HDMI Port
6 Line In (Light Blue) 14 DVI-D Port
7 Front Speaker (Lime)** 15 USB 3.1 Gen1 Port (USB3_12)
8 Microphone (Pink) 16 Antenna Ports
8911
English
3
* ere are two LEDs on each LAN port. Please refer to the table below for the LAN port LED indications.
ACT/LINK LED
SPEED LED
LAN Por t
Activity / Link LED Speed LED
Status Description Status Description
O No Link O 10Mbps connection Blinking Data Activity Orange 100Mbps connection On Link Green 1Gbps connection
** If you use a 2- channel speaker, plea se connect the speake r’s plug into “Front Speaker Jack”. See the table below for connection d etails in accordance w ith the type of speaker you use.
English
Audio Output
Channels
Front Speaker
(No. 7)
Rear Speaker
(No. 5)
Central / Bass
(No. 4)
2 V -- -- -- 4 V V -- -- 6 V V V -- 8 V V V V
To enable Multi-Streaming, you need to connect a front panel audio cable to the front panel audio header. Aer restarting your computer, you will nd the “Mixer” tool on your system. Please select “Mixe r ToolBox” , click “Enable playback multi-streaming”, and click “ok”. Choose “2CH”, “4CH”, “6CH”, or “8CH” and then you are allowed to select “Realtek HDA Primary output” to u se the Rear Speaker, Central/Bass, and Front Speaker, or select “Realtek HDA Audio 2nd output” to use the front panel audio.
Line In (No. 6)
4
Chapter 1 Introduction
ank you for purchasing ASRock Z370 Extreme4 motherboard, a reliable motherboard produced under ASRock’s consistently stringent quality control. It delivers excellent performance with robust design conforming to ASRock’s commitment to quality and endurance.
Becau se the motherboard specications and the BIOS soware might be updated, the content of this documentation will be subject to change without notice. In case any modi­cations of this documentation occur, the updated version will be availabl e on ASRock’s website w ithout further notice. If you require technical support related to this mother­board, please visit our website for specic information about the model you are using. You may nd the l atest VGA cards and CPU suppor t list on ASRock’s website a s well. ASRock website http://www.asrock.com.
1.1 Package Contents
ASRock Z370 Extreme4 Motherboard (ATX Form Factor)
•
ASRock Z370 Extreme4 Quick Installation Guide
•
ASRock Z370 Extreme4 Support CD
•
1 x I/O Panel Shield
•
4 x Serial ATA (SATA) Data Cables (Optional)
•
1 x ASRock SLI_HB_Bridge_2S Card (Optional)
•
3 x Screws for M.2 Socket (Opti onal)
•
Z370 Extreme4
English
5
1.2 Specications
Platform
CPU
Chipset
Memory
* Please refer to Memory Support List on ASRock's website for more information. (http://www.asrock.com/) * 8th Gen Intel® CPU supports DDR4 up to 2666.
ATX Form Factor
•
Supports 8th Generation Intel® CoreTM Processors (Socket
•
1151) Digi Power design
•
12 Power Phase design
•
Supports Intel® Turbo Boost 2.0 Technology
•
Supports Intel® K-Series unlocked CPUs
•
Supports ASRock BCLK Full-range Overclocking
•
Intel® Z370
•
Dual Channel DDR4 Memory Technology
•
4 x DDR4 DIMM Slots
•
Supports DDR4 4333+(OC)*/4000(OC)/3866(OC)/
•
3800(OC)/3733(OC)/3600(OC)/3200(OC)/2933(OC)/2800 (OC)/2666/2400/2133 non-ECC, un-buered memory
Supports ECC UDIMM memory modules (operate in non-
•
ECC mode) Max. capacity of system memory: 64GB
•
Supports Intel® Extreme Memory Prole (XMP) 2.0
•
15μ Gold Contact in DIMM Slots
•
English
6
Expansion Slot
3 x PCI Express 3.0 x16 Slots (PCIE2/PCIE4/PCIE6: single
•
at x16 (PCIE2); dual at x8 (PCIE2) / x8 (PCIE4); triple at x8 (PCIE2) / x8 (PCIE4) / x4 (PCIE6))*
* Supports NVMe SSD as boot disks
3 x PCI Express 3.0 x1 Slots (Flexible PCIe)
•
Supports AMD Quad CrossFireXTM, 3-Way CrossFireXTM
•
and CrossFireXTM Supports NVIDIA® Quad SLITM and SLI
•
1 x M.2 Socket (Key E), supports type 2230 WiFi/BT module
•
15μ Gold Contact in VGA PCIe Slot (PCIE2)
•
TM
Graphics
Z370 Extreme4
Intel® HD Graphics Built-in Visuals and the VGA outputs
•
can be supported only with processors which are GPU integrated. Supports Intel® HD Graphics Built-in Visuals : Intel® Quick
•
Sync Video with AVC, MVC (S3D) and MPEG-2 Full HW Encode1, Intel® InTruTM 3D, Intel® Clear Video HD Technology, Intel® InsiderTM, Intel® HD Graphics DirectX 12
•
HWAEncode/Decode: VP9 8-bit, VP9 10-bit (Encode only),
•
VP8, HEVC (MPEG-H Part2, h.265), AVC (MPEG4, h.264), MPEG2-Part2 (h.262), JPEG/MJPEG,VC-1 Max. shared memory 1024MB
•
* e size of maximum shared memory may vary from dierent operating systems.
ree graphics output options: D-Sub, DVI-D and HDMI
•
Supports Triple Monitor
•
Supports HDMI with max. resolution up to 4K x 2K
•
(4096x2160) @ 30Hz Supports DVI-D with max. resolution up to 1920x1200 @
•
60Hz Supports D-Sub with max. resolution up to 1920x1200 @
•
60Hz Supports Auto Lip Sync, Deep Color (12bpc), xvYCC and
•
HBR (High Bit Rate Audio) with HDMI Port (Compliant HDMI monitor is required) Supports HDCP with DVI-D and HDMI Ports
•
Supports 4K Ultra HD (UHD) playback with HDMI Port
•
Audio
7.1 CH HD Audio with Content Protection (Realtek
•
ALC1220 Audio Codec) Premium Blu-ray Audio support
•
Supports Surge Protection
•
Supports Purity SoundTM 4
•
- Nichicon Fine Gold Series Audio Caps
- 120dB SNR DAC with Dierential Amplier
- NE5532 Premium Headset Amplier for Front Panel Audio Connector (Supports up to 600 Ohm headsets)
- Pure Power-In
English
7
LAN
Rear Panel I/O
- Direct Drive Technology
- PCB Isolate Shielding
- Impedance Sensing on Front Out port
-
Individual PCB Layers for R/L Audio Channel
- RGB LED
- 15μ Gold Audio Connector Supports DTS Connect
•
Gigabit LAN 10/100/1000 Mb/s
•
Giga PHY Intel® I219V
•
Supports Wake-On-LAN
•
Supports Lightning/ESD Protection
•
Supports Energy Ecient Ethernet 802.3az
•
Supports PXE
•
2 x Antenna Ports
•
1 x PS/2 Mouse/Keyboard Port
•
1 x D-Sub Port
•
1 x DVI-D Port
•
1 x HDMI Port
•
1 x Optical SPDIF Out Port
•
1 x USB 3.1 Gen2 Type-A Port (10 Gb/s) (ASMedia ASM3142)
•
(Supports ESD Protection) 1 x USB 3.1 Gen2 Type-C Port (10 Gb/s) (ASMedia ASM3142)
•
(Supports ESD Protection) 4 x USB 3.1 Gen1 Ports (Intel® Z370) (Supports ESD
•
Protection) 1 x RJ-45 LAN Port with LED (ACT/LINK LED and SPEED
•
LE D) HD Audio Jacks: Rear Speaker / Central / Bass / Line in /
•
Front Speaker / Microphone
English
8
Storage
6 x SATA3 6.0 Gb/s Connectors, support RAID (RAID 0,
•
RAID 1, RAID 5, RAID 10, Intel Rapid Storage Technology
15), NCQ, AHCI and Hot Plug* 2 x SATA3 6.0 Gb/s Connectors by ASMedia ASM1061, sup-
•
port NCQ, AHCI and Hot Plug
* M2_1, SATA3_0 and SATA3_1 share lanes. If either one of them is in use, the others will be disabled. * M2_2, SATA3_4 and SATA3_5 share lanes. If either one of them is in use, the others will be disabled.
Connector
Z370 Extreme4
1 x Ultra M.2 Socket (M2_1), supports M Key type
•
2230/2242/2260/2280 M.2 SATA3 6.0 Gb/s module and M.2 PCI Express module up to Gen3 x4 (32 Gb/s)** 1 x Ultra M.2 Socket (M2_2), supports M Key type
•
2230/2242/2260/2280/22110 M.2 SATA3 6.0 Gb/s module
and M.2 PCI Express module up to Gen3 x4 (32 Gb/s)** ** Supports Intel® OptaneTM Tech nolo gy ** Supports NVMe SSD as boot disks ** Supports ASRock U.2 Kit
1 x COM Port Header
•
1 x TPM Header
•
1 x Power LED and Speaker Header
•
1 x RGB LED Header
•
* Supports in total up to 12V/3A, 36W LED Strip
1 x CPU Fan Connector (4-pin)
•
* e CPU Fan Connector supports the CPU fan of maximum 1A (12W) fan power.
1 x CPU Optional/Water Pump Fan Connector (4-pin)
•
* e CPU Optional/Water Pump Fan supports the water cooler fan of maximum 1.5A (18W) fan power.
2 x Chassis Fan Connectors (4-pin) (Smart Fan Speed
•
Control)
1 x Chassis Optional/Water Pump Fan Connector (4-pin)
•
* e Chassis Optional/Water Pump Fan supports the water cooler fan of maximum 1.5A (18W) fan power. * CHA_FAN1 and CHA_FAN2 can auto detect if 3-pin or 4-pin fan is in use.
1 x 24 pin ATX Power Connector (Hi-Density Power
•
Conn ector)
1 x 8 pin 12V Power Connector (Hi-Density Power
•
Conn ector)
1 x Front Panel Audio Connector (15μ Gold Audio
•
Conn ector)
1 x underbolt AIC Connector (5-pin)
•
3 x USB 2.0 Headers (Support 6 USB 2.0 ports) (Intel® Z370)
•
(Supports ESD Protection)
1 x USB 3.1 Gen1 Header (Supports 2 USB 3.1 Gen1 ports)
•
(Intel® Z370) (Supports ESD Protection)
English
9
BIOS Feature
Hardware Monitor
1 x USB 3.1 Gen1 Header (Supports 2 USB 3.1 Gen1 ports)
•
(ASMedia ASM1074 hub) (Supports ESD Protection) 1 x Front Panel Type C USB 3.1 Gen1 Header (ASMedia
•
ASM1074 hub)
2 x AMI UEFI Legal BIOS with multilingual GUI support
•
(1 x Main BIOS and 1 x Backup BIOS) Supports Secure Backup UEFI Technology
•
ACPI 6.0 Compliant wake up events
•
SMBIOS 2.7 Support
•
CPU Core/Cache, GT Core/Cache, DRAM, PCH 1.0V,
•
VCCIO, VCCST, VCCSA, VCCPLL, CPU Internal PLL, GT PLL, Ring PLL, System Agent PLL, Memory Controller PLL Voltage Multi-adjustment
Temperature Sensing: CPU, CPU Optional/Water Pump,
•
Chassis, Chassis Optional/Water Pump Fans Fan Tachometer: CPU, CPU Optional/Water Pump, Chassis,
•
Chassis Optional/Water Pump Fans Quiet Fan (Auto adjust chassis fan speed by CPU tempera-
•
ture): CPU, CPU Optional/Water Pump, Chassis, Chassis Optional/Water Pump Fans Fan Multi-Speed Control: CPU, CPU Optional/Water Pump,
•
Chassis, Chassis Optional/Water Pump Fans Voltage monitoring: +12V, +5V, +3.3V, CPU Vcore, DRAM,
•
VPPM, PCH 1.0V, VCCSA, VCCST
English
10
Microso® Windows® 10 64-bit
OS
Certica­tions
* For detailed product information, please visit our website: http://www.asrock.com
•
FCC, CE
•
ErP/EuP ready (ErP/EuP ready power supply is required)
•
Z370 Extreme4
Please realize that the re is a certain risk involved with overclocking, including adjusting the setting in the BIOS, applying Untied Overclocking Technology, or using third-party overclocking tools. O verclocking may aect your system’s stability, or even cause damage to the components and devices of your system. It should be done at your ow n risk and expense. We are not responsible for possible damage caused by overclocking.
11
English
Chapter 2 Installation
is is an ATX form factor motherboard. Before you install the motherboard, study the conguration of your chassis to ensure that the motherboard ts into it.
Pre-installation Precautions
Take note of the following precautions before you install motherboard components or change any motherboard settings.
Make sure to unplug the power cord before installing or removing the motherboard
•
components. Failure to do so may cause physical injuries and damages to motherboard components. In order to avoid damage from static electricity to the motherboard’s components,
•
NEVER place your motherboard directly on a carpet. Also remember to use a grounded wrist strap or touch a safety grounded object before you handle the components. Hold components by the edges and do not touch the ICs.
•
Whenever you uninstall any components, place them on a grounded anti-static pad or
•
in the bag that comes with the components. When placing screws to secure the motherboard to the chassis, please do not over-
•
tighten the screws! Doing so may damage the motherboard.
English
12
2.1 Installing the CPU
1. Before you insert the 1151-Pin CPU into the socket, ple ase check if the P nP cap is on the socket, if the CPU surface is unclean, or if there are any bent pins in the socket. Do not force to in sert the CPU into the socket if above situation is found . Otherwise, the CPU will be seriously damaged.
2. Unplug all power cables before in stalling the CPU.
1
Z370 Extreme4
A
B
2
English
13
3
4
English
14
5
Please save and replace the cover if the processor i s removed. e cover must be placed if you wish to return the motherboard for aer service.
Z370 Extreme4
15
English
2.2 Installing the CPU Fan and Heatsink
1 2
English
16
FAN
CPU_
Z370 Extreme4
2.3 Installing Memory Modules (DIMM)
is motherboard provides four 288-pin DDR4 (Double Data Rate 4) DIMM slots, and supports Dual Channel Memory Technology.
1. For dual channel conguration , you always need to in stall identical (the same brand, speed , size and chip-type) DDR4 DIMM pairs.
2. It is unable to activate Dual Channel Memor y Technology with only one or three memory module installed.
3. It is not allowed to install a DDR, DDR2 or DDR3 memory module into a DDR4 slot; otherwise, this motherboard and DIMM may be damaged.
Dual Channel Memory Conguration
Priority DDR4_A1 DDR4_A2 DDR4_B1 DDR4_B2
1 Populated Populated 2 Populated Populated Populated Populated
e DIMM only ts in one correct orientation. It will cause permanent damage to the motherboard and the DIMM if you force the DIMM into the slot at incorrect orientation.
17
English
1
2
English
18
3
2.4 Expansion Slots (PCI Express Slots)
ere are 6 PCI Express slots on the motherboard.
Before installing an ex pansion card, please make sure that the power supply is switched o or the power cord is unplugged. Please read the documentation of the expansion card and make necessary hardware settings for the card before you start the installation.
PCIe slots:
PCIE1 (PCIe 3.0 x1 slot) is used for PCI Express x1 lane width cards. PCIE2 (PCIe 3.0 x16 slot) is used for PCI Express x16 lane width graphics cards. PCIE3 (PCIe 3.0 x1 slot) is used for PCI Express x1 lane width cards. PCIE4 (PCIe 3.0 x16 slot) is used for PCI Express x8 lane width graphics cards. PCIE5 (PCIe 3.0 x1 slot) is used for PCI Express x1 lane width cards.
PCIE6 (PCIe 3.0 x16 slot) is used for PCI Express x4 lane width graphics cards.
PCIe Slot Congurations
PCIE2 PCIE4 PCIE6
Z370 Extreme4
Single Graphics Card x16 N/A N/A
Two Graphics Cards in
CrossFireXTM or SLITM
Mode
ree Graphics Cards in
3-Way CrossFireXTM Mode
For a better ther mal environment, please connect a chassi s fan to the motherboard’s chas­sis fan connector (CHA_ FAN1, CHA_ FAN2 or CHA_FAN3 ) when using multiple graphics cards.
x8 x8 N/A
x8 x8 x4
English
19
2.5 Jumpers Setup
e illustration shows how jumpers are setup. When the jumper cap is placed on the pins, the jumper is “Short”. If no jumper cap is placed on the pins, the jumper is “Open”.
English
Clear CMOS Jumper (C LRC MO S1) (see p.1, No. 25)
CLRCMOS1 allows you to clear the data in CMOS. e data in CMOS includes system setup information such as system password, date, time, and system setup parameters. To clear and reset the system parameters to default setup, please turn o the computer and unplug the power cord, then use a jumper cap to short the pins on CLRCMOS1 for 3 seconds. Please remember to remove the jumper cap aer clearing the CMOS. If you need to clear the CMOS when you just nish updating the BIOS, you must boot up the system rst, and then shut it down before you do the clear-CMOS action.
2-pin Jumper
Short: Clear CMOS Open: Default
20
2.6 Onboard Headers and Connectors
Onboard headers and connectors are NOT jumpers. Do NOT place jumper caps over these heade rs and connectors. Placing jumper caps over the headers and connectors will cause permanent damage to the motherboard.
Z370 Extreme4
System Panel Header (9-pi n PANEL1) (see p.1, No. 14)
PWRBTN (Power Button):
Connec t to the power button on the chassi s front panel. You may congure the way to tur n o your system using the power button.
RESET (Reset B utton): Connec t to the reset button on the chassi s front panel. Press the reset button to restart the computer if the computer f reezes and fails to per form a normal restar t.
PLED (Syste m Power LED): Connec t to the power status indicator on the chassis front panel. e LED i s on when the system is operating. e LED keeps blinking when the system is in S1/S3 sleep state. e LED is o when the system is in S4 slee p state or powered o (S5).
HDLED (Ha rd Drive Activity LED): Connec t to the hard drive activity LED on the chassis front panel. e LED is on when the hard drive is reading or wr iting data.
e front panel design may dier by chassis. A front panel module mainly consists of power button, reset button , power LED, hard dr ive activity LED, speaker and etc. When connect­ing your chassi s front panel module to thi s header, make sure the wire a ssignments and the pin assignments are matched correctly.
1
PLED+
PLED-
HDLED-
HDLED+
PWRBTN#
GND
RESET#
GND
GND
Connect the power button, reset button and system status indicator on the chassis to this header according to the pin assignments below. Note the positive and negative pins before connecting the cables.
21
English
Power LED and Speaker
1
+5V
DUMMY
PLED+
PLED+
PLED-
DUMMY
SPEAKER
DUMMY
GND
GND
P+
P-
USB_PWR
P+
P-
USB_PWR
1
Header (7-pin SPK_PLED1) (see p.1, No. 15)
Please connect the chassis power LED and the chassis speaker to this header.
English
Serial ATA3 Connectors (SATA3_4_5: see p.1, No. 10) (SATA3_2_3: see p.1, No. 11) (SATA3_0_1: see p.1, No. 12) (SATA3_A1_A2: see p.1, No. 13)
USB 2.0 Headers (9-pin USB_1_2) (see p.1, No. 19) (9-pin USB_3_4) (see p.1, No. 20) (9-pin USB_5_6) (see p.1, No. 18)
SATA3_2SATA3_0
SATA3_A1 SATA3_4
ese eight SATA3 connectors support SATA data cables for internal storage devices with up to
6.0 Gb/s data transfer rate. * M2_1, SATA3_0 and
SATA3_3SATA3_1
SATA3_1 share lanes. If either one of them is in use, the others will be disabled. * M2_2, SATA3_4 and SATA3_5 share lanes. If either one of them is in use, the others will be
SATA3_A2 SATA3_5
disabled. *To minimize the boot time, use Intel® Z370 SATA ports (SATA3_0) for your bootable devices.
ere are three headers on this motherboard. Each USB 2.0 header can support two ports.
22
Z370 Extreme4
1
J_SENSE
OUT2_L
1
MIC_RET
PRESENCE#
GND
OUT2_R
MIC2_R
MIC2_L
OUT_RET
USB 3.1 Gen1 Headers (19-pin USB3_5_6) (see p.1, No. 7) (19-pin USB3_7_8) (see p.1, No. 8)
Front Panel Type C USB
3.1 Gen1 Header (26-pin USB3_TC_1) (see p.1, No. 9)
Front Panel Audio Header (9-pin HD_ AUDIO1) (see p.1, No. 26)
Vbus
IntA_PA_SSRX-
IntA_PA_SSRX+
GND
IntA_PA_SSTX-
IntA_PA_SSTX+
GND
IntA_PA_D-
IntA_PA_D+
VbusVbus
IntA_PB_SSRX-
IntA_PB_SSRX+
GND
IntA_PB_SSTX-
IntA_PB_SSTX+
GND
IntA_PB_D-
IntA_PB_D+
Dummy
ere are two headers on this motherboard. Each USB 3.1 Gen1 header can support two ports.
ere is one Front Panel Type C USB 3.1 Gen1 Header on this motherboard. is header is used for connecting a USB 3.1 Gen1 module for additional USB 3.1 Gen1 ports.
is header is for connecting audio devices to the front audio panel.
1. High Denition Audio supports Jack Sensing, but the panel wire on the chassis must sup­port HDA to function correctly. Please follow the instructions in our manual and chassis manual to install your system.
2. If you use an AC’97 audio panel , please install it to the front panel audio header by the steps below: A. Connect Mic_IN (MIC) to MIC2_ L. B. Conne ct Audio_R (RIN) to OUT2_R and Audio_ L (LIN) to OUT2_ L. C. Connect Ground (GND) to Ground (GND). D. MIC_ RET and OUT_RET are for the HD audio panel only. You don’t need to connect them for the AC’97 audio panel . E. To activate the front mic, go to the “FrontMic” Tab in the Realtek Control panel and adjust “Recording Volume”.
English
23
Chassis Fan Connectors
GN
OL
FA
FAN_SPEED_CONTROL
1 2 3 4
D
F
4 3 2 1
GND
OL
(4-pin CHA_FAN1) (see p.1, No. 27)
(4-pin CHA_FAN2) (see p.1, No. 22)
AN_SPEED_CONTROL
CHA_FAN_SPEED
FAN_VOLTAGE
FAN_VOLTAGE
FAN_SPEED
FAN_SPEED_CONTR
1 2 3 4
Please connect fan cables to the fan connectors and match the black wire to the ground pin.
GN
Chassis Optional/Water Pump Fan Connector (4-pin CHA_FAN3/W_ PUMP) (see p.1, No. 16)
CPU Fan Connector (4-pin CPU_FAN1) (see p.1, No. 2)
CPU Optional/Water Pump Fan Connector (4-pin CPU_OPT/W_ PUM P) (see p.1, No. 3)
D
FAN_VOLTAGE
FAN_SPEED
FAN_SPEED_CONTR
1 2 3 4
CPU_FAN_SPEED
FAN_VOLTAGE
GND
N_SPEED_CONTROL
CPU_FAN_SPEED
FAN_VOLTAGE
GND
is motherboard provides a 4-Pin water cooling
chassis connectors. If you plan to connect a 3-Pin water cooler fan, please connect it to Pin 1-3.
is motherboard provides a 4-Pin CPU fan (Quiet Fan) connector. If you plan to connect a 3-Pin CPU fan, please connect it to Pin 1-3.
is motherboard
4
provides a 4-Pin water
3
2
cooling CPU fan
1
connector. If you plan to connect a 3-Pin CPU water cooler fan, please connect it to Pin 1-3.
fan
chassis
English
24
ATX Power Connector (24-pin ATXPWR1) (see p.1, No. 6)
12
24
is motherboard pro­vides a 24-pin ATX power connector. To use a 20-pin ATX power supply, please plug it along Pin 1 and Pin
1
13
13.
Z370 Extreme4
4 1
8 5
1
1
1
#
ATX 12V Power Connector (8-pin ATX12V1) (see p.1, No. 1)
underbolt AIC Connectors (5-pin TB1) (see p.1, No. 23)
Serial Port Header (9-pin COM1) (see p.1, No. 17)
TPM Header (17-pi n TPMS1) (see p.1, No. 21)
is motherboard provides an 8-pin ATX 12V power connector. To use a 4-pin ATX power supply, please plug it along Pin 1 and Pin 5.
Please connect a underbolt™ add-in card (AIC) to the underbolt AIC connector via the GPIO cable. *Please install the underbolt™ AIC card to PCIE6 (default slot).
RRXD1
DDTR#1
TTXD1
DDCD#1
DDSR#1
CCTS#1
RRTS#1
GND
RRI#1
is COM1 header supports a serial port module.
is connector supports Trusted
GN D
LAD 0
+3 V
+3V S B
D
GN
GN D
LAD 1
SER IRQ #
S_P WRD WN #
PC ICL K
LAD 3
PC IRS T
FRA M E
GN D
LAD 2
Platform Module (TPM) system,
1
which can securely store keys, digital certicates, passwords, and data. A TPM system also helps enhance network security,
SMB _CL K_M AIN
protects digital identities, and ensures platform integrity.
RGB LED Header (4-pi n RGB _LED) (see p.1, No. 24)
12V GRB
RGB header is used to connect RGB LED extension cable which allows users to choose from vari­ous LED lighting eects.
Caution: Never install the RGB
LED cable in the wrong orienta-
tion; otherwise, the cable may
be damaged.
*Please refer to page 32 for further instructions on on this header.
English
25
2.7 M.2 WiFi/BT Module Installation Guide (M2_3)
e M.2 Socket (Key E) supports type 2230 WiFi/BT module.
Installing the WiFi/BT module
Step 1
Prepare a type 2230 WiFi/BT module and the screw.
Step 2
Find the nut location to be used.
PCB Length: 3cm Module Type: Type2230
A
English
26
Step 3
Align and gently insert the WiFi/BT module into the M.2 slot. Please be aware that the module only ts in one orientation.
A
o
A
20
Z370 Extreme4
Step 4
Tighten the screw with a screwdriver to secure the module into place. Please do not overtighten the screw as this might damage the module.
A
27
English
2.8 M.2_SSD (NGFF) Module Installation Guide (M2_1 and
5
M2_2)
The M.2, also known as the Next Generation Form Factor (NGFF), is a small size and versatile card edge connector that aims to replace mPCIe and mSATA. The Ultra M.2 Sockets (M2_1 and M2_2) support SATA3 6.0 Gb/s module and M.2 PCI Express module up to Gen3 x4 (32 Gb/s). * M2_1, SATA3_0 and SATA3_1 share lanes. If either one of them is in use, the others will be disabled. * M2_2, SATA3_4 and SATA3_5 share lanes. If either one of them is in use, the others will be disabled.
Installing the M.2_SSD (NGFF) Module
e following is an example of installing M.2_SSD (NGFF) module into the M2_2.
Step 1
Prepare a M.2_SSD (NGFF) module and the screw.
English
28
4
3
Depending on the PCB type and length of your M.2_SSD (NGFF) module, nd the corresponding nut
Step 2
2
1
A
BCDE
location to be used.
No. 1 2 3 4 5
Nut Location A B C D E
PCB Length 3cm 4.2cm 6cm 8cm 11cm
Module Type Type 2230 Type 224 2 Type2 260 Ty pe 2280 Type 22110
Loading...
+ 146 hidden pages