No part of this installation guide may be reproduced, transcribed, transmitted, or translated in any language, in any form or by any means, except duplication of documentation by the purchaser for backup purpose, without written consent of ASRock Inc.
Products and corporate names appearing in this guide may or may not be registered
trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners’ benefit, without intent to infringe.
Disclaimer:Disclaimer:
Disclaimer:
Disclaimer:Disclaimer:
Specifications and information contained in this guide are furnished for informational
use only and subject to change without notice, and should not be constructed as a
commitment by ASRock. ASRock assumes no responsibility for any errors or omissions
that may appear in this guide.
With respect to the contents of this guide, ASRock does not provide warranty of any kind,
either expressed or implied, including but not limited to the implied warranties or
conditions of merchantability or fitness for a particular purpose. In no event shall
ASRock, its directors, officers, employees, or agents be liable for any indirect, special,
incidental, or consequential damages (including damages for loss of profits, loss of
business, loss of data, interruption of business and the like), even if ASRock has been
advised of the possibility of such damages arising from any defect or error in the guide
or product.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
CALIFORNIA, USA ONLY
The Lithium battery adopted on this motherboard contains Perchlorate, a toxic
substance controlled in Perchlorate Best Management Practices (BMP) regulations
passed by the California Legislature. When you discard the Lithium battery in
California, USA, please follow the related regulations in advance.
“Perchlorate Material-special handling may apply, see
www.dtsc.ca.gov/hazardouswaste/perchlorate”
3Line In (Light Blue)8D-Sub Port
4 Front Speaker (Lime)9COM Port
5 Microphone (Pink)10 PS/2 Keyboard Port (Purple)
* There are two LED next to the LAN port. Please refer to the table below for the LAN port LED
indications.
LAN Port LED Indications
Activity/Link LEDSPEED LED
Status Description Status Description
Off No Activity N68C-GS4 FX:
Blinking Data Activity Off 10Mbps connection
Orange 100Mbps connection
Green 1Gbps connection
N68C-S4 FX:
Off 10Mbps connection
Orange 100Mbps connection
8
7
6
ACT/LINK
LED
LAN Port
SPEED
LED
ASRock N68C-GS4 FX / N68C-S4 FX Motherboard
EnglishEnglish
EnglishEnglish
English
33
3
33
For Realtek ALC662 Audio Codec:
To enable Multi-Streaming function, you need to connect a front panel audio cable to the front
panel audio header. Please refer to below steps for the software setting of Multi-Streaming.
For Windows® XP:
After restarting your computer, you will find “Mixer” tool on your system. Please select “Mixer
ToolBox” , click “Enable playback multi-streaming”, and click “ok”. Choose “2CH” or
“4CH” and then you are allowed to select “Realtek HDA Primary output” to use Rear Speaker
and Front Speaker, or select “Realtek HDA Audio 2nd output” to use front panel audio. Then
reboot your system.
For Windows® 8 / 7 / VistaTM:
After restarting your computer, please double-click “Realtek HD Audio Manager” on the
system tray. Set “Speaker Configuration” to “Quadraphonic” or “Stereo”. Click “Device
advanced settings”, choose “Make front and rear output devices playbacks two different audio
streams simultaneously”, and click “ok”. Then reboot your system.
®
For VIA
VT1705 Audio Codec:
To enable Multi-Streaming function, you need to connect a front panel audio cable to the front
panel audio header. After restarting your computer, you will find “VIA HD Audio Deck” tool on
your system. Please follow below instructions according to the OS you install.
For Windows® XP OS:
Please click “VIA HD Audio Deck” icon , and click “Speaker”. Then you are allowed to
select “2 Channel” or “4 Channel”. Click “Power” to save your change.
For Windows® 8 / 7 / VistaTM OS:
Please click “VIA HD Audio Deck” icon , and click “Advanced Options” on the left side
on the bottom. In “Advanced Options” screen, select “Independent Headphone”, and click
“OK” to save your change.
English
EnglishEnglish
EnglishEnglish
44
4
44
ASRock N68C-GS4 FX / N68C-S4 FX Motherboard
1.1.
IntroductionIntroduction
1.
Introduction
1.1.
IntroductionIntroduction
Thank you for purcha sing ASRock N68C-GS4 FX / N68C-S4 FX motherboard, a relia ble
motherboard produced under ASRock’s consistently stringent quality control. It delivers
excellent performance with robust design conforming to ASRock’s commitment to quality and endurance.
In this manual, cha pter 1 a nd 2 contain introduction of the motherboard and ste p-by-step
guide to the hardware installation. Chapter 3 and 4 contain the configuration guide to
BIOS setup and information of the Support CD.
Because the motherboard specifications and the BIOS software might
be updated, the content of this manual will be subject to change without
notice. In case any modifications of this manual occur, the updated
version will be available on ASRock website without further notice. You
may find the latest VGA cards and CPU support lists on ASRock website
as well. ASRock website
If you require technical support related to this motherboard, please visit
our website for specific information about the model you are using.
www.asrock.com/support/index.asp
1.11.1
PP
ackack
1.1
1.11.1
One ASRock N68C-GS4 FX / N68C-S4 FX Motherboard (Micro A TX Form Factor)
One ASRock N68C-GS4 FX / N68C-S4 FX Quick Installation Guide
One ASRock N68C-GS4 FX / N68C-S4 FX Support CD
Two Serial A TA (SAT A) Data Cables (Optional)
One I/O Panel Shield
age Contentsage Contents
P
ack
age Contents
PP
ackack
age Contentsage Contents
http://www.asrock.com
ASRock N68C-GS4 FX / N68C-S4 FX Motherboard
EnglishEnglish
EnglishEnglish
English
55
5
55
1.2 Specifications1.2 Specifications
1.2 Specifications
1.2 Specifications1.2 Specifications
Platform- Micro ATX Form Fa ctor
A-Style- Home Cloud (N68C-GS4 FX)
CPU- Support for Socket AM3+ processors
- Support for AM3 proce ssors: A MD PhenomTM II X6 / X4 / X3 /
X2 (except 920 / 940) / Athlon II X4 / X3 / X2 / Sempron
processors (see CAUTION 1)
- Support for Socket AM2+ / AM2 processors: AM D Phenom
FX / Phenom / Athlon 64 FX / Athlon 64 X2 Dual-Core / Athlon
X2 Dual-Core / Athlon 64 / Sempron processor
- Supports 8-Core CPU
- Supports UCC feature (Unlock CPU Core) (see CAUTION 2)
/ 7 32-bit / 7 64-bit / VistaTM 32-bit / VistaTM 64-bit / XP 32-bit /
XP 64-bit (see CAUTION 6)
Certifications- FCC, CE, WHQL
- ErP/EuP ready (ErP/EuP ready power supply is required)
* For detailed product information, please visit our website:
WAR NING
Please realize that there is a certain risk involved with overclocking, including
adjusting the setting in the BIOS, applying Untied Overclocking Technology, or using
the third-party overclocking tools. Overclocking may affect your system stability, or
even cause damage to the components and devices of your system. It should be
done at your own risk and expense. We are not responsible for possible damage
caused by overclocking.
http://www.asrock.com
CAUTION!
1. This motherboard supports CPU up to 95W. Please refer to our website for
CPU support list. ASRock website
2. UCC (Unlock CPU Core) feature simplifies AMD CPU activation. As long as
a simple switch of the BIOS option “ASrock UCC”, you can unlock the extra
CPU core to enjoy an instant performance boost. When UCC feature is
enabled, the dual-core or triple-core CPU will boost to the quad-core CPU,
and some CPU, including quad-core CPU, can also increase L3 cache size
up to 6MB, which means you can enjoy the upgrade CPU performance with
a better price. Please be noted that UCC feature is supported with AM2+ /
AM3 / AM3+ CPU only , and in addition, not every AM2+ / AM3 / AM3+ CPU ca n
support this function because some CPU’s hidden core may be
malfunctioned.
3. Whether 1600MHz memory speed is supported depends on the AM3/
AM3+ CPU you adopt. If you want to adopt DDR3 1600 memory module
on this motherboard, please refer to the memory support list on our
website for the compatible memory modules.
ASRock website http://www.asrock.com
4. Due to the operating system limitation, the actual memory size may be
less than 4GB for the reservation for system usage under Windows® 8
English
EnglishEnglish
EnglishEnglish
/ 7 / VistaTM / XP. For Windows® OS with 64-bit CPU, there is no such
limitation.
5. Whether 1066MHz memory speed is supported depends on the AM2+
/ AM3 CPU you adopt. If you want to adopt DDR2 1066 memory module
on this motherboard, please refer to the memory support list on our
website for the compatible memory modules.
ASRock website http://www.asrock.com
6. This motherboard does not support RAID mode under Windows® 8.1
32-bit / 8.1 64-bit.
ASRock motherboard is equipped with pin headers with obvious colors which indicate
you to recognize the crucial headers more easily. Please refer to below illustrations for
the pin definition of onboard headers. If you want to have more information about the
usage of these headers, please refer to “Jumpers Setup“ and “Onboard Headers and
Connectors“ for details.
GND
PRESENCE#
MIC_RET
OUT_RET
1
MIC2_R
MIC2_L
J_SENSE
OUT2_R
OUT2_L
Front Panel Audio Header
PLED+
PLED-
PWRBTN#
GND
1
HDLED+
GND
HDLED-
REST#
DUMMY
System Panel Header
1
DUMMY
DUMMY
+5V
Chassis Speaker Header
SPEAKER
USB_PWR
P-
P+
GND
DUMMY
1
GND
P+
P-
USB_PWR
USB 2.0 Header
ASRock N68C-GS4 FX / N68C-S4 FX Motherboard
EnglishEnglish
EnglishEnglish
English
99
9
99
1.4 Jumpers Setup1.4 Jumpers Setup
1.4 Jumpers Setup
1.4 Jumpers Setup1.4 Jumpers Setup
The illustration shows how jumpers are setup.
When the jumper cap is placed on pins, the
jumper is “Short”. If no jumper cap is pla ced on
pins, the jumper is “Open”. The illustration
shows a 3-pin jumper whose pin1 and
pin2 are “Short” when jumper cap is pla ced on
these 2 pins.
JumperSetting
Clear CMOS Jumper
(CLRCMOS1)
(see p.2, No. 17)
Note: CLRCMOS1 allows you to clear the data in CMOS. The data in CMOS includes
system setup information such as system password, date, time, and system
setup parameters. To clear and reset the system parameters to default setup,
please turn off the computer and unplug the power cord from the power supply.
After waiting for 15 seconds, use a jumper ca p to short pin2 and pin3 on CLRCMOS1
for 5 seconds. However, please do not clear the CMOS right
after you update the BIOS. If you need to clear the CMOS when you just finish
updating the BIOS, you must boot up the system first, and then shut it down
before you do the clear-CMOS action.
If you clear the CMOS, the case open may be detected. Please adjust the
BIOS option “Clear Status” to clear the record of previous chassis intrusion
status.
1_2
Default
2_3
Clear CMOS
English
EnglishEnglish
EnglishEnglish
1010
10
1010
ASRock N68C-GS4 FX / N68C-S4 FX Motherboard
1.5 Onboard Headers and Connectors1.5 Onboard Headers and Connectors
1.5 Onboard Headers and Connectors
1.5 Onboard Headers and Connectors1.5 Onboard Headers and Connectors
Onboard headers and connectors are NOT jumpers. Do NOT place
jumper caps over these headers and connectors. Placing jumper
caps over the headers and connectors will cause permanent damage of the motherboard!
•
Floppy Connector
(33-pin FLOPPY1)
(see p.2 No. 19)
Note: Make sure the red-striped side of the cable is plugged into Pin1 side of the
Pin1
FLOPPY1
the red-striped side to
Pin1
connector.
Primary IDE connector
(39-pin IDE1, see p.2 No. 6)
PIN1
connect the blue end
to the motherboard
IDE1
connect the black end
to the IDE devices
80-conductor ATA 66/100/133 ca ble
Note: Please refer to the instruction of your IDE device vendor for the details.
Serial A TA2 ConnectorsThese four Serial AT A2 (SA T A2)
(SATAII_1 (PORT 0.0):connectors support SATA2
see p.2, No. 7)or SATA hard disk for internal
(SATAII_2 (PORT 0.1):storage devices. The current
see p.2, No. 10)SA TA2 interface allows up to
(SATAII_3 (PORT 1.0):3.0 Gb/s data tra n s fer rate.
see p.2, No. 8)
(SATAII_4 (PORT 1.1):
see p.2, No. 9)
SATAII_1 SATAII_3
(PORT 0.0) (PORT 1.0)
SATAII_2 SATAII_4
(PORT 0.1) (PORT 1.1)
ASRock N68C-GS4 FX / N68C-S4 FX Motherboard
1111
11
1111
EnglishEnglish
EnglishEnglish
English
1
1
1
USB_PWR
P-5
P-4
USB_PWR
USB_PW R
P-7
P-6
USB_PW R
USB_PWR
P-9
P-8
USB_PWR
P+5
P+4
P+7
P+6
P+9
P+8
GND
GND
GND
GND
GND
GND
DUMMY
motherboard. Each USB 2.0
header can support two USB
2.0 ports.
DUMMY
DUMMY
USB 2.0 HeadersBesides four default USB 2.0
(9-pin USB4_5)ports on the I/O panel, there are
(see p.2 No. 13)three USB 2.0 headers on this
(9-pin USB6_7)
(see p.2 No. 12)
(9-pin USB8_9)
(see p.2 No. 11)
Print Port HeaderThis is an interface f or print
(25-pin LPT1)port cable that allows
(see p.2 No. 18)convenient connection of printer
Front Panel Audio HeaderThis is an interface f or the front
(9-pin HD_AUDIO1)panel audio cable that allows
(see p.2, No. 22)convenient connection and
1
AFD#
STB#
ERROR#
PINIT#
SPD1
SPD0
SLIN#
SPD2
SPD3
SPD4
1
SPD5
GND
MIC2_L
GND
SPD7
SPD6
PRESENCE#
MIC_RET
OUT2_R
MIC2_R
ACK#
J_SENSE
BUSY
OUT_RET
OUT2_L
PE
SLCT
control of audio devices.
devices.
1. High Definition Audio supports Jack Sensing, but the panel wire on
English
EnglishEnglish
EnglishEnglish
the chassis must support HDA to function correctly. Please follow the
instruction in our manual and chassis manual to install your system.
2. If you use AC’97 audio panel, please install it to the front panel audio
header as below:
A. Connect Mic_IN (MIC) to MIC2_L.
B. Connect Audio_R (RIN) to OUT2_R and Audio_L (LIN) to OUT2_L.
C. Connect Ground (GND) to Ground (GND).
D. MIC_RET and OUT_RET are for HD audio panel only. You don’t
need to connect them for AC’97 audio panel.
1212
12
1212
ASRock N68C-GS4 FX / N68C-S4 FX Motherboard
1
1
PLED+
HDLED+
DUMMY
+5V
PLED-
PWRBTN#
GND
HDLED-
DUMMY
GND
DUMMY
RESET#
SPEAKER
System Panel HeaderThis hea der accommodates
(9-pin PANEL1)several system front panel
(see p.2 No. 16)functions.
Chassis Spea ker Hea derPlease connect the chassis
(4-pin SPEAKER 1)speaker to this header.
(see p.2 No. 14)
Chassis and Power Fan ConnectorsPlease connect the fan cables
(3-pin CHA_FAN1)to the fan connectors and
(see p.2 No. 15)match the black wire to the
(3-pin PWR_FAN1)
(see p.2 No. 20)
FAN_SPEED
CHA_FAN_SPEED
+12V
GND
+12V
GND
ground pin.
CPU Fan ConnectorPlease connect the CPU fan
(4-pin CPU_FAN1)cable to this connector and
(see p.2 No. 1)match the black wire to the
4 3 2 1
+12V
FAN_SPEED_CONTROL
CPU_FAN_SPEED
GND
ground pin.
Though this motherboard provides 4-Pin CPU fan (Quiet Fan) support, the 3-Pin
CPU fan still can work successfully even without the fan speed control function.
If you plan to connect the 3-Pin CPU fan to the CPU fan connector on this
motherboard, please connect it to Pin 1-3.
Pin 1-3 Connected
3-Pin Fan Installation
ATX Power Conne ctorPlease connect an ATX power
(24-pin ATXPWR1)supply to this connector.
(see p.2 No. 5)
Though this motherboard provides 24-pin ATX power connector,
12 124
13
12
it can still work if you adopt a traditional 20-pin ATX power supply.
To use the 20-pin ATX power supply, please plug your power
supply along with Pin 1 and Pin 13.
20-Pin ATX Power Supply Installation
1
24
EnglishEnglish
EnglishEnglish
English
13
ASRock N68C-GS4 FX / N68C-S4 FX Motherboard
1313
13
1313
ATX 12V Power ConnectorPlease note that it is necessary
(4-pin ATX12V1)to connect a power supply with
(see p.2 No. 2)ATX 12V plug to this connector.
Failing to do so will cause power
up failure.
Chassis Intrusion Hea derThis motherboard supports CASE
(2-pin CI1)OPEN detection feature that
(see p.2 No. 21)detects if the chassis cover has
2. BIOS Information2. BIOS Information
2. BIOS Information
2. BIOS Information2. BIOS Information
The Flash Memory on the motherboard stores BIOS Setup Utility. When you start up
the computer, please press <F2> or <Del> during the Power-On-Self-Test (POST) to
enter BIOS Setup utility; otherwise, POST continues with its test routines. If you wish to
enter BIOS Setup after POST, please restart the system by pressing <Ctl> + <Alt> +
<Delete>, or pressing the reset button on the system cha ssis. The BIOS Setup program
is designed to be user-friendly. It is a menu-driven program, which allows you to scroll
through its various sub-menus and to select among the predetermined choices. For the
detailed information about BIOS Setup, plea se refer to the User M anual (PDF file) contained in the Support CD.
1
Signal
GND
been removed. This feature
requires a chassis with chassis
intrusion detection design.
3. Software Support CD information3. Software Support CD information
3. Software Support CD information
3. Software Support CD information3. Software Support CD information
This motherboard supports various Microsoft® Windows® operating systems: 8.1 32-bit
/ 8.1 64-bit / 8 32-bit / 8 64-bit / 7 32-bit / 7 64-bit / VistaTM 32-bit / VistaTM 64-bit / XP 32bit / XP 64-bit. The Support CD that came with the motherboard contains necessary
drivers and useful utilities that will enhance motherboard features. To begin using the
Support CD, insert the CD into your CD-ROM drive. It will display the Main Menu auto-
English
EnglishEnglish
EnglishEnglish
matically if “AUTORUN” is enabled in your computer . If the Main Menu does not appear
automatically, locate a nd double-click on the file “ASRSETUP.EXE” from the “BIN” folder
in the Support CD to display the menus.
1414
14
1414
ASRock N68C-GS4 FX / N68C-S4 FX Motherboard
SpezifikationenSpezifikationen
Spezifikationen
SpezifikationenSpezifikationen
Plattform- Micro A TX-Formfa ktor
A-Stil- Heim-Cloud (N68C-GS4 FX)
CPU- Unterstützung von Socket AM3+-Prozessoren