Asrock H61M-IDE Quick Installation Guide

Version 1.0

Published November 2013

No part of this documentation may be reproduced, transcribed, transmitted, or translated in any language, in any form or by any means, except duplication of documentation by the purchaser for backup purpose, without written consent of ASRock Inc.

Products and corporate names appearing in this documentation may or may not be registered trademarks or copyrights of their respective companies, and are used only for identication or explanation and to the owners’ benet, without intent to

infringe.

Disclaimer:

Specications and information contained in this documentation are furnished for informational use only and subject to change without notice, and should not be constructed as a commitment by ASRock. ASRock assumes no responsibility for any errors or omissions that may appear in this documentation.

With respect to the contents of this documentation, ASRock does not provide warranty of any kind, either expressed or implied, including but not limited to the implied warranties or conditions of merchantability or tness for a particular purpose.

In no event shall ASRock, its directors, ocers, employees, or agents be liable for any indirect, special, incidental, or consequential damages (including damages for loss of prots, loss of business, loss of data, interruption of business and the like), even if ASRock has been advised of the possibility of such damages arising from any defect or error in the documentation or product.

is device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that

may cause undesired operation.

CALIFORNIA, USA ONLY

e Lithium battery adopted on this motherboard contains Perchlorate, a toxic substance controlled in Perchlorate Best Ma nagement Practices (BMP) regulations passed by the California Legislature. When you discard the Lithium battery in California, USA, please follow the related regulations in advance. “Perchlorate Material-special handling may apply, see www.dtsc.ca.gov/hazardouswaste/perchlorate”

ASRock Website: http://www.asrock.com

ASRock H61M-IDE Motherboard

English

Motherboard Layout

DDR 3_ A1 (64 bi t, 24 0-p in mo dul e)

DDR 3_ B1 (64 bi t, 24 0-p in mo dul e)

Intel

H61

PCIE1

AUDIO CODEC

ATX12V 1

USB6_7

HDLED RESET

PLED PWR BTN

PANEL1

CLRCMOS 1

PLED1

CPU_FAN1

HD_AUDI O1

USB4_5

CMOS

BATT ERY

PCIE2

LAN

CI1

Fa st R A M

Fa st L A N

Ro HS

ATXP WR 1

32Mb BIOS

SATA_2 SATA_0

SATA_3 SATA_1

SPDIF_OU T1

IR1

Sup er

I/O

CHA_FAN1

PS2

Keyb oard

PS2

Mous e

Top:

LINE IN

Center :

FRONT

Bottom :

MIC IN

Top: RJ-4 5

USB 2.0 T: USB 2 B: U SB3

USB 2. 0 T: USB0 B: USB 1

VGA1

H6 1 M - ID E

IDE1

TPM1

English

1 ATX 12V Power Connector (ATX12V1) 11 Power LED Header (PLED1) 2 CPU Fan Connector (CPU_FAN1) 12 System Panel Header (PANEL1) 3 2 x 240-pin DDR3 DIMM Slots 13 USB 2.0 Header (USB4_5) (Dual Channel: DDR3_A1, DDR3_B1) 14 USB 2.0 Header (USB6_7) 4 ATX Power Connector (ATXPWR1) 15 Primary IDE Connector (IDE1) 5 Chassis Fan Connector (CHA_FAN1) 16 Infrared Module Header (IR1) 6 SATA2 Connector (SATA_1) 17 Front Panel Audio Header (HD_AUDIO1) 7 SATA2 Connector (SATA_0) 18 SPDIF Out Connector (SPDIF_OUT1) 8 SATA2 Connector (SATA_3) 19 Chassis Intrusion Header (CI1) 9 SATA2 Connector (SATA_2) 20 TPM Header (TPM1) 10 Clear CMOS Jumper (CLRCMOS1)

ASRock H61M-IDE Motherboard

I/O Panel

1 PS/2 Mouse Port (Green) 6 USB 2.0 Ports (USB23) 2 LAN RJ-45 Port* 7 USB 2.0 Ports (USB01) 3 Line In (Light Blue) 8 D-Sub Port (VGA1) 4 Front Speaker (Lime) 9 PS/2 Keyboard Port (Purple) 5 Microphone (Pink)

* There are two LED next to the LAN port. Please refer to the table below for the LAN port LED

indications.

Activity/Link LED SPEED LED

Status Description Status Description

LAN Port LED Indications

Off No Link Off 10Mbps connection

Blinking Data Activity Orange 100Mbps connection

On Link Green 1Gbps connection

ACT/LINK LED

LAN Port

SPEED LED

To enable Multi-Streaming function, you need to connect a front panel audio cable to the front

panel audio header. Please refer to below steps for the software setting of Multi-Streaming.

For Windows® XP:

After restarting your computer, you will nd “Mixer” tool on your system. Please select “Mixer ToolBox” , click “Enable playback multi-streaming”, and click “ok”. Choose “2CH” or

“4CH” and then you are allowed to select “Realtek HDA Primary output” to use Rear Speaker and Front Speaker, or select “Realtek HDA Audio 2nd output” to use front panel audio. Then

reboot your system.

For Windows® 8 / 7 / VistaTM:

After restarting your computer, please double-click “Realtek HD Audio Manager” on the system tray. Set “Speaker Conguration” to “Quadraphonic” or “Stereo”. Click “Device advanced settings”, choose “Make front and rear output devices playbacks two different audio streams simultaneously”, and click “ok”. Then reboot your system.

ASRock H61M-IDE Motherboard

English

1. Introduction

Thank you for purchasing ASRock H61M-IDE motherboard, a reliable motherboard produced under ASRock’s consistently stringent quality control. It delivers excellent performance with robust design conforming to ASRock’s commitment to quality and

endurance.

This Quick Installation Guide contains introduction of the motherboard and step-by-

step installation guide. More detailed information of the motherboard can be found

in the user manual presented in the Support CD.

Because the motherboard specications and the BIOS software might be

updated, the content of this manual will be subject to change without no-

tice. In case any modications of this manual occur, the updated version will be available on ASRock website without further notice. You may nd the latest VGA cards and CPU support lists on ASRock website as well. ASRock website http://www.asrock.com If you require technical support related to this motherboard, please visit our website for specic information about the model you are using.

www.asrock.com/support/index.asp

1.1 Package Contents

ASRock H61M-IDE Motherboard (Micro ATX Form Factor) ASRock H61M-IDE Quick Installation Guide ASRock H61M-IDE Support CD 2 x Serial ATA (SATA) Data Cables (Optional) 1 x ATA 133 Cable (Optional) 1 x I/O Panel Shield

English

ASRock Reminds You...

To get better performance in Windows® 8 / 8 64-bit / 7 / 7 64-bit / Vista

VistaTM 64-bit, it is recommended to set the BIOS option in Storage Con-

guration to AHCI mode. For the BIOS setup, please refer to the “User Manual” in our support CD for details.

ASRock H61M-IDE Motherboard

1.2 Specications

Platform - Micro ATX Form Factor

- All Solid Capacitor design

CPU - Supports 3rd and 2nd Generation Intel® CoreTM i7 / i5 / i3 /

Xeon® / Pentium® / Celeron® in LGA1155 package

- Supports Intel® Turbo Boost 2.0 Technology

- Supports K-Series unlocked CPU Chipset - Intel® H61

- Supports Intel® Rapid Start Technology and Smart Connect

Technology

Memory - Dual Channel DDR3 Memory Technology

- 2 x DDR3 DIMM Slots

- Supports DDR3 1600/1333/1066 non-ECC, un-buffered memory (DDR3 1600 with Intel® Ivy Bridge CPU, DDR3 1333 with Intel® Sandy Bridge CPU)

- Max. capacity of system memory: 16GB (see CAUTION 1)

- Supports Intel® Extreme Memory Prole (XMP) 1.3 / 1.2 with Intel® Ivy Bridge CPU Expansion Slot - 1 x PCI Express 3.0 x16 Slot (Blue @ x16 mode)

* PCIE 3.0 is only supported with Intel® Ivy Bridge CPU. With Intel® Sandy Bridge CPU, it only supports PCIE 2.0.

- 1 x PCI Express 2.0 x1 Slot

Graphics * Intel® HD Graphics Built-in Visuals and the VGA outputs can be supported only with processors which are GPU

integrated.

- Supports Intel® HD Graphics Built-in Visuals: Intel® Quick Sync Video 2.0, Intel® InTruTM 3D, Intel® Clear Video HD Technology, Intel® InsiderTM, Intel® HD Graphics 2500/4000 with Intel® Ivy Bridge CPU

- Supports Intel® HD Graphics Built-in Visuals: Intel® Quick Sync Video, Intel® InTruTM 3D, Intel® Clear Video HD Technology, Intel® HD Graphics 2000/3000, Intel® Advanced Vector Extensions (AVX) with Intel® Sandy Bridge CPU

- Pixel Shader 5.0, DirectX 11 with Intel® Ivy Bridge CPU. Pixel Shader 4.1, DirectX 10.1 with Intel® Sandy Bridge CPU.

- Max. shared memory 1760MB with Intel® Ivy Bridge CPU. Max. shared memory 1759MB with Intel® Sandy Bridge CPU.

English

ASRock H61M-IDE Motherboard

English

- Supports D-Sub with max. resolution up to 2048x1536 @ 75Hz

Audio - 5.1 CH HD Audio (Realtek ALC662 Audio Codec) LAN - PCIE x1 Gigabit LAN 10/100/1000 Mb/s

- Realtek RTL8111GR (see CAUTION 2)

- Supports Realtek RealWoW! Technology

- Supports Wake-On-LAN

- Supports LAN Cable Detection

- Supports Energy Efcient Ethernet 802.3az

- Supports PXE

Rear Panel I/O - 1 x PS/2 Mouse Port

- 1 x PS/2 Keyboard Port

- 1 x D-Sub Port

- 4 x USB 2.0 Ports

- 1 x RJ-45 LAN Port with LED (ACT/LINK LED and SPEED

LED)

- HD Audio Jacks: Line in/Front Speaker/Microphone Storage - 4 x SATA2 3.0 Gb/s Connectors, support NCQ, AHCI and Hot Plug Connector - 1 x ATA133 IDE Connector (Supports 2 x IDE devices)

- 1 x IR Header

- 1 x Power LED Header

- 1 x Chassis Intrusion Header

- 1 x TPM Header

- 1 x CPU Fan Connectors (4-pin)

- 1 x Chassis Fan Connector (4-pin)

- 1 x 24 pin ATX Power Connector

- 1 x 4 pin 12V Power Connector

- 1 x Front Panel Audio Connector

- 1 x SPDIF Out Connector

- 2 x USB 2.0 Headers (Support 4 USB 2.0 ports) BIOS Feature - 32Mb AMI UEFI Legal BIOS with GUI support

- Supports “Plug and Play”

- ACPI 1.1 Compliant wake up events

- Supports jumperfree

- SMBIOS 2.3.1 support Support CD - Drivers, Utilities, AntiVirus Software (Trial Version), Google Chrome Browser and Toolbar, Start8 (30 days trial)

ASRock H61M-IDE Motherboard

Hardware - CPU/Chassis temperature sensing Monitor - CPU/Chassis Fan Tachometer

- CPU Quiet Fan (Auto adjust chassis fan speed by CPU

temperature)

- CPU/Chassis Fan multi-speed control

- CASE OPEN detection

- Voltage monitoring: +12V, +5V, +3.3V, CPU Vcore

OS - Microsoft® Windows® 8 / 8 64-bit / 7 / 7 64-bit / Vista

VistaTM 64-bit / XP / XP 64-bit compliant

Certications - FCC, CE, WHQL

* For detailed product information, please visit our website: http://www.asrock.com

WARNING

Please realize that there is a certain risk involved with overclocking, including adjusting the setting in the BIOS, applying Untied Overclocking

Technology, or using third-party overclocking tools. Overclocking may

affect your system’s stability, or even cause damage to the components and devices of your system. It should be done at your own risk and

expense. We are not responsible for possible damage caused by

overclocking.

CAUTION!

1. Due to the operating system limitation, the actual memory size may be less than 4GB for the reservation for system usage

under Windows® 8 / 7 / VistaTM / XP. For Windows® OS with 64-

bit CPU, there is no such limitation. You can use ASRock XFast RAM to utilize the memory that Windows® cannot use.

2. Realtek RealWoW! Technology allows you to wake up this sys-

tem from remote mobile devices, such as smart phones, tables,

or other PCs. It needs third-party softwares and applications to utilize this feature. Please visit our website for Home Cloud

topic.

ASRock H61M-IDE Motherboard

English

1.3 Pin Header Easy Installation Guide

GND

PRE SENC E#

MIC_ RET

MIC2 _L

MIC2 _R

OUT2 _R

J_SE NSE

OUT2 _L

OUT_ RET

PLE D+

PLE D-

PWRB TN#

HDL ED+

HDL ED-

GND

REST #

GND

DUMM Y

USB_ PWR

P-

P+

USB_ PWR

P-

P+

GND

DUMM Y

GND

PLED +

PLED -

PLED +

ASRock motherboard is equipped with pin headers with obvious colors which indicate you to recognize the crucial headers more easily. Please refer to below illustrations for the pin denition of onboard headers. If you want to have more information about the usage of these headers, please refer to “Jumpers Setup“ and “Onboard Headers and Connectors“ for details.

English

Front Panel Audio Header

SPDIF_OUT Header

ASRock H61M-IDE Motherboard

Power LED Header

System Panel Header

USB 2.0 Header

1.4 Jumpers Setup

The i llust rat io n sho ws how jumpe rs are

setup. When the jumper cap is placed on

pins, the jumper is “Short”. If no jumper cap is placed on pins, the jumper is “Open”. The

illustration show s a 3-pin jumper w ho se

pin1 and pin2 are “Short” when jumper cap is placed on these 2 pins.

Jumper Setting Description

Clear CMOS Jumper

(CLRCMOS1) (see p.2, No. 10)

Note: CLRCMOS1 allows you to clear the data in CMOS. To clear and reset the

system parameters to default setup, please turn off the computer and unplug

the power cord from the power supply. After waiting for 15 seconds, use a

jumper cap to short pin2 and pin3 on CLRCMOS1 for 5 seconds. However, please do not clear the CMOS right after you update the BIOS. If you need to clear the CMOS when you just nish updating the BIOS, you must boot up the system rst, and then shut it down before you do the clear-CMOS action. Please be noted that the password, date, time and user default prole will be cleared only if the CMOS battery is removed.

Clear CMOSDefault

If you clear the CMOS, the case open may be detected. Please adjust the BIOS option “Clear Status” to clear the record of previous chassis

intrusion status.

ASRock H61M-IDE Motherboard

English

1.5 Onboard Headers and Connectors

Onboard headers and connectors are NOT jumpers. Do NOT place

jumper caps over these headers and connectors. Placing jumper caps

over the headers and connectors will cause permanent damage of the

motherboard!

Serial ATA2 Connectors These four Serial ATA2

(SATA_0: see p.2, No. 7)

(SATA_1: see p.2, No. 6)

(SATA_2: see p.2, No. 9)

(SATA_3: see p.2, No. 8)

3.0 Gb/s data transfer rate.

Serial ATA (SATA) Either end of the SATA data

Data Cable cable can be connected to the

(Optional)

SATA / SATA2 hard disk or the

SATA2 connector on this

motherboard.

USB 2.0 Headers Besides four default USB 2.0

(9-pin USB4_5)

(see p.2 No. 13)

this motherboard. Each

USB 2.0 header can support two USB 2.0 ports.

(9-pin USB6_7) (see p.2 No. 14)

(SATA2) connectors support

SATA_3 SATA_1

SATA data cables for internal

storage devices. The current

SATA2 interface allows up to

SATA_2 SATA_0

ports on the I/O panel, there

are two USB 2.0 headers on

English

Infrared Module Header This header supports an

(5-pin IR1)

optional wireless transmitting

(see p.2 No. 16)

and receiving infrared module.

ASRock H61M-IDE Motherboard

Front Panel Audio Header This is an interface for front

(9-pin HD_AUDIO1)

(see p.2 No. 17)

panel audio cable that allows

convenient connection and

control of audio devices.

GND

PRE SEN CE#

MIC 2_R

MIC 2_L

MIC _RE T

J_S ENS E

OUT 2_R

OUT _RE T

OUT 2_L

1. High Denition Audio supports Jack Sensing, but the panel wire on the chassis must support HDA to function correctly. Please follow the

instruction in our manual and chassis manual to install your system.

2. If you use AC’97 audio panel, please install it to the front panel audio

header as below:

A. Connect Mic_IN (MIC) to MIC2_L. B. Connect Audio_R (RIN) to OUT2_R and Audio_L (LIN) to OUT2_L. C. Connect Ground (GND) to Ground (GND). D. MIC_RET and OUT_RET are for HD audio panel only. You don’t

need to connect them for AC’97 audio panel.

E. To activate the front mic.

For Windows® XP / XP 64-bit OS:

Select “Mixer”. Select “Recorder”. Then click “FrontMic”.

For Windows® 8 / 8 64-bit / 7 / 7 64-bit / VistaTM / VistaTM 64-bit OS:

Go to the "FrontMic" Tab in the Realtek Control panel. Adjust

“Recording Volume”.

System Panel Header This header accommodates

(9-pin PANEL1)

(see p.2 No. 12)

several system front panel

functions.

Connect the power switch, reset switch and system status indicator on the

chassis to this header according to the pin assignments below. Note the

positive and negative pins before connecting the cables.

PWRBTN (Power Switch):

Connect to the power switch on the chassis front panel. You may congure

the way to turn off your system using the power switch.

RESET (Reset Switch):

Connect to the reset switch on the chassis front panel. Press the reset

switch to restart the computer if the computer freezes and fails to perform a

normal restart.

PLED (System Power LED):

Connect to the power status indicator on the chassis front panel. The LED

ASRock H61M-IDE Motherboard

English

is on when the system is operating. The LED keeps blinking when the sys-

tem is in S1 sleep state. The LED is off when the system is in S3/S4 sleep

state or powered off (S5).

HDLED (Hard Drive Activity LED):

Connect to the hard drive activity LED on the chassis front panel. The LED

is on when the hard drive is reading or writing data.

The front panel design may differ by chassis. A front panel module mainly

consists of power switch, reset switch, power LED, hard drive activity LED,

speaker and etc. When connecting your chassis front panel module to this

header, make sure the wire assignments and the pin assign-ments are

matched correctly.

English

Power LED Header Please connect the chassis

(3-pin PLED1)

(see p.2 No. 11)

power LED to this header to

indicate system power status.

PLE D+

PLE D-

The LED is on when the system

is operating. The LED keeps

blinking in S1 state. The LED is

off in S3/S4 state or S5 state

(power off).

Chassis Fan Connector Please connect the fan cables

(4-pin CHA_FAN1)

(see p.2 No. 5)

to the fan connectors and

match the black wire to the

ground pin.

CPU Fan Connectors Please connect the CPU fan

(4-pin CPU_FAN1)

(see p.2 No. 2)

cable to the connector and

match the black wire to the

ground pin.

Though this motherboard provides 4-Pin CPU fan (Quiet Fan) support, the 3-Pin

CPU fan still can work successfully even without the fan speed control function. If you plan to connect the 3-Pin CPU fan to the CPU fan connector on this

motherboard, please connect it to Pin 1-3.

4 3 2 1

+12 V

FAN_ SPE ED_ CON TR O L

CPU _FAN _SP EED

GND

Pin 1-3 Connected

3-Pin Fan Installation

ASRock H61M-IDE Motherboard

ATX Power Connector Please connect an ATX power

(24-pin ATXPWR1)

(see p.2 No. 4)

supply to this connector.

12 124

Though this motherboard provides 24-pin ATX power connector,

it can still work if you adopt a traditional 20-pin ATX power supply. To use the 20-pin ATX power supply, please plug your

power supply along with Pin 1 and Pin 13.

20-Pin ATX Power Supply Installation

ATX 12V Power Connector Please connect an ATX 12V

(4-pin ATX12V1)

(see p.2 No. 1)

power supply to this connector.

Chassis Intrusion Header This motherboard supports

(2-pin CI1)

CASE OPEN detection feature

(see p.2, No. 19)

that detects if the chassis cover

Sig n al

GND

has been removed. This feature

requires a chassis with chassis

intrusion detection design.

SPDIF Out Connector Please connect the

(2-pin SPDIF_OUT1)

(see p.2, No. 18)

HDMI VGA card to this header

SPDIF_OUT connector of a

GND

SPD I FOU T

with a cable.

TPM Header This connector supports

(17-pin TPM1)

(see p.2, No. 20)

Trusted Platform Module (TPM)

system, which can securely

store keys, digital certicates,

passwords, and data. A TPM

system also helps enhance

English

network security, protects

digital identities, and ensures

platform integrity.

ASRock H61M-IDE Motherboard

Primary IDE Connector

(39-pin IDE1, see p.2 No. 15)

English

connect the blue end

to the motherboard

80-conductor ATA 66/100/133 cable

Note: Please refer to the instruction of your IDE device vendor for the details.

connect the black end

to the IDE devices

2. BIOS Information

The Flash Memory on the motherboard stores BIOS Setup Utility. When you start up the computer, please press <F2> or <Del> during the Power-On-Self-Test (POST) to enter BIOS Setup utility; otherwise, POST continues with its test routines. If you wish to enter BIOS Setup after POST, please restart the system by pressing <Ctl> + <Alt> + <Delete>, or pressing the reset button on the system chassis. The BIOS Setup program is designed to be user-friendly. It is a menu-driven program, which

allows you to scroll through its various sub-menus and to select among the prede-

termined choices. For the detailed information about BIOS Setup, please refer to the User Manual (PDF le) contained in the Support CD.

3. Software Support CD information

This motherboard supports various Microsoft

64-bit / 7 / 7 64-bit / VistaTM / Vista

came with the motherboard contains necessary drivers and useful utilities that will

enhance motherboard features. To begin using the Support CD, insert the CD into your CD-ROM drive. It will display the Main Menu automatically if “AUTORUN” is enabled in your computer. If the Main Menu does not appear automatically, locate and double-click on the le “ASRSETUP.EXE” from the BIN folder in the Support CD

to display the menus.

64-bit / XP / XP 64-bit. The Support CD that

Windows® operating systems: 8 / 8

ASRock H61M-IDE Motherboard

Spezikationen

Plattform - Micro ATX-Formfaktor

- Alle Feste Kondensatordesign CPU - Unterstützt Intel® CoreTM i7- / i5- / i3- / Xeon®- / Pentium®- /

Celeron®-Prozessoren der 3ten und 2ten Generation im

LGA1155-Package

- Unterstützt Intel® Turbo Boost 2.0-Technologie

- Unterstützt freigegebene CPU der K-Serie Chipsatz - Intel® H61

- Unterstützt Intel® Rapid Start Technology und Smart Connect Technology Speicher - Unterstützung von Dual-Kanal-Speichertechnologie

- 2 x Steckplätze für DDR3

- Unterstützt DDR3 1600/1333/1066 non-ECC, ungepufferter Speicher (DDR3 1600 mit Intel® Ivy Bridge-Prozessor, DDR3 1333 mit Intel® Sandy Bridge-Prozessor)

- Max. Kapazität des Systemspeichers: 16GB

- Unterstützt Intel® Extreme Memory Prole (XMP)1.3/1.2 mit Intel® Ivy Bridge-Prozessor Erweiterungs- - 1 x PCI Express 3.0 x16-Steckplatz (blau für x16-Modus) steckplätze * PCIE 3.0 wird nur mit Intel® Ivy Bridge-Prozessor unterstützt. Mit Intel® Sandy Bridge-Prozessor wird nur PCIE 2.0 unterstützt.

- 1 x PCI Express 2.0 x1-Steckplätze Onboard-VGA * Integrierte Intel® HD-Grakdarstellungen und die VGA- Ausgänge können nur durch GPU-integrierte Prozessoren unterstützt werden.

- Unterstützt hochauösende integrierte Intel®-Graklösungen: Intel® Quick-Sync-Video 2.0, Intel® InTruTM 3D, Intel® Clear Video-Technik (HD), Intel® InsiderTM, Intel® HD Graphics 2500/4000 mit Intel® Ivy Bridge-Prozessor

- Unterstützt hochauösende integrierte Intel®-Graklösungen: Intel® Quick-Sync-Video, Intel® InTruTM 3D, Intel® Clear Video-Technik (HD), Intel® HD Graphics 2000/3000, Intel® Advanced Vector Extensions (AVX) mit Intel® Sandy Bridge Prozessor

- Pixel Shader 5.0, DirectX 11 mit Intel® Ivy Bridge-Prozessor, Pixel Shader 4.1, DirectX 10.1 mit Intel® Sandy Bridge Prozessor

Deutsch

ASRock H61M-IDE Motherboard

Deutsch

- Maximal gemeinsam genutzter Speicher 1760MB mit Intel® Ivy Bridge-Prozessor. Maximal gemeinsam genutzter Speicher 1759MB mit Intel® Sandy Bridge-Prozessor.

- Unterstützt D-Sub mit einer maximalen Auösung von 2048 x 1536 bei 75 Hz

Audio - 5.1 CH HD Audio (Realtek ALC662 Audio Codec) LAN - PCIE x1 Gigabit LAN 10/100/1000 Mb/s

- Realtek RTL8111GR

- Unterstützt Realtek RealWoW! Technology

- Unterstützt Wake-On-LAN

- Unterstützt LAN-Kabelerkennung

- Unterstützt energieefzientes Ethernet 802.3az

- Unterstützt PXE

E/A-Anschlüsse - 1 x PS/2-Mausanschluss an der - 1 x PS/2-Tastaturanschluss Rückseite - 1 x D-Sub port

- 4 x Standard-USB 2.0-Anschlüsse

- 1 x RJ-45 LAN Port mit LED (ACT/LINK LED und SPEED

LED)

- HD Audiobuchse: Audioeingang / Lautsprecher vorne /

Mikrofon

Speichergerät - 4 x SATA2 3,0 GB/s-Anschlüsse, unterstützen NCQ-, AHCI- und „Hot Plug“ (Hot-Plugging)- Funktionen Anschlüsse - 1 x ATA133 IDE-Anschlüsse (Unterstützt bis 2 IDE-Geräte)

- 1 x Infrarot-Modul-Header

- 1 x Betriebs-LED-Header

- 1 x Verteiler für Gehäuseeindringversuche

- 1 x TPM-Header

- 1 x CPUlüfter-Anschluss (4-pin)

- 1 x Gehäuselüfter-Anschluss (4-pin)

- 1 x 24-pin ATX-Netz-Header

- 1 x 4-pin anschluss für 12V-ATX-Netzteil

- 1 x Anschluss für Audio auf der Gehäusevorderseite

- 1 x SPDIF Out-Anschluss

- 2 x USB 2.0-Anschlüsse (Unterstützung 4 zusätzlicher USB 2.0-Anschlüsse) BIOS - 32Mb AMIs Legal BIOS UEFI mit GUI-Unterstützung

- Unterstützung für “Plug and Play”

- ACPI 1.1-Weckfunktionen

- JumperFree-Übertaktungstechnologie

- SMBIOS 2.3.1

ASRock H61M-IDE Motherboard

+ 35 hidden pages

Asrock H61M-IDE Quick Installation Guide

Specifications and Main Features

Frequently Asked Questions

User Manual

English