Asrock H61M-HVS, H61M-HVGS User Manual

No part of this installation guide may be reproduced, transcribed, transmitted, or translated in any language, in any form or by any means, except duplication of documentation by the purchaser for backup purpose, without written consent of ASRock Inc. Products and corporate names appearing in this guide may or may not be registered trademarks or copyrights of their respective companies, and are used only for identiﬁ ca- tion or explanation and to the owners’ beneﬁ t, without intent to infringe.

Disclaimer:

Speciﬁ cations and information contained in this guide are furnished for informational use only and subject to change without notice, and should not be constructed as a commitment by ASRock. ASRock assumes no responsibility for any errors or omissions that may appear in this guide. With respect to the contents of this guide, ASRock does not provide warranty of any kind, either expressed or implied, including but not limited to the implied warranties or conditions of merchantability or ﬁ tness for a particular purpose. In no event shall ASRock, its directors, ofﬁ cers, employees, or agents be liable for any indirect, special, incidental, or consequential damages (including damages for loss of proﬁ ts, loss of business, loss of data, interruption of business and the like), even if ASRock has been advised of the possibility of such damages arising from any defect or error in the guide or product.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that

may cause undesired operation.

CALIFORNIA, USA ONLY

The Lithium battery adopted on this motherboard contains Perchlorate, a toxic substance controlled in Perchlorate Best Management Practices (BMP) regulations passed by the California Legislature. When you discard the Lithium battery in California, USA, please follow the related regulations in advance. “Perchlorate Material-special handling may apply, see www.dtsc.ca.gov/hazardouswaste/perchlorate”

ASRock Website: http://www.asrock.com

Published April 2011

ASRock H61M-HVGS / H61M-HVS Motherboard

English

Motherboard Layout (H61M-HVGS / H61M-HVS)

17.3cm (6.8in)

Keyboard

Mouse

PS2

DX10.1

VGA1

HDMI1

ErP/EuP Ready

USB2.0 T: US B0 B:USB1

USB2.0 T: US B2 B:USB3

USB 2.0

Top:

T:USB4

RJ-45

B: USB5

Bottom:

MIC IN

Top:

LINE IN

Center:

FRONT

PWR_FAN1

LAN PHY

PCI Express2.0

PCIE1

ATX12 V1

RoHS

CPU_FAN1

Designed in Taipei

DR3 D

Dual Channel

HDMI 1.4a

DDR3_B1 (64bit, 240-pin module)

DDR3_A1 (64bit, 240-pin module)

22.6cm (8.9in)

ATXPWR1

English

Super

AUDIO CODEC

I/O

CLRCMOS1

CMOS

HD_AUDIO1

PCIE2

LPT1

Battery

USB8_9

COM1

USB6_7

Intel

H61

SATA2_3

SPEAKER1

PLEDPWRBTN

HDLED RESET

SATA2_2

PANEL1

32Mb BIOS

SATA2_1

CHA_FAN1

SATA2_0

1 1155-Pin CPU Socket 13 Chassis Speaker Header (SPEAKER 1, White) 2 ATX 12V Power Connector (ATX12V1) 14 System Panel Header (PANEL1, White) 3 CPU Fan Connector (CPU_FAN1) 15 USB 2.0 Header (USB6_7, Blue) 4 ATX Power Connector (ATXPWR1) 16 USB 2.0 Header (USB8_9, Blue) 5 2 x 240-pin DDR3 DIMM Slots 17 COM Port Header (COM1) (Dual Channel: DDR3_A1, DDR3_B1, Blue) 18 Print Port Header (LPT1, White) 6 Intel H61 Chipset 19 Front Panel Audio Header 7 32Mb SPI Flash (HD_AUDIO1, White) 8 SATA2 Connector (SATA2_1, Blue) 20 PCI Express 2.0 x1 Slot (PCIE2, White) 9 Chassis Fan Connector (CHA_FAN1) 21 Clear CMOS Jumper (CLRCMOS1) 10 SATA2 Connector (SATA2_0, Blue) 22 PCI Express 2.0 x16 Slot (PCIE1, Blue) 11 SATA2 Connector (SATA2_3, Blue) 23 Power Fan Connector (PWR_FAN1) 12 SATA2 Connector (SATA2_2, Blue)

ASRock H61M-HVGS / H61M-HVS Motherboard

I/O Panel (H61M-HVGS)

1 PS/2 Mouse Port (Green) 7 USB 2.0 Ports (USB23) * 2 LAN RJ-45 Port 8 USB 2.0 Ports (USB01) 3 Line In (Light Blue) 9 VGA/HDMI Port ** 4 Front Speaker (Lime) 10 VGA/D-Sub Port 5 Microphone (Pink) 11 PS/2 Keyboard Port (Purple) 6 USB 2.0 Ports (USB45)

* There are two LED next to the LAN port. Please refer to the table below for the LAN port LED indications.

Activity/Link LED SPEED LED

Status Description Status Description

LAN Port LED Indications

ACT/LINK LED

SPEED LED

Off No Link Off 10Mbps connection Blinking Data Activity Orange 100Mbps connection On Link Green 1Gbps connection

LAN Port

To enable Multi-Streaming function, you need to connect a front panel audio cable to the front panel audio header. After restarting your computer, you will ﬁ nd “VIA HD Audio Deck” tool on your system. Please follow below instructions according to the OS you install. For Windows Please click “VIA HD Audio Deck” icon , and click “Speaker”. Then you are allowed to

select “2 Channel” or “4 Channel”. Click “Power” to save your change. For Windows® 7 / 7 64-bit / VistaTM / VistaTM 64-bit OS: Please click “VIA HD Audio Deck” icon , and click “Advanced Options” on the left side

on the bottom. In “Advanced Options” screen, select “Independent Headphone”, and click “OK” to save your change.

XP / XP 64-bit OS:

ASRock H61M-HVGS / H61M-HVS Motherboard

English

I/O Panel (H61M-HVS)

* There are two LED next to the LAN port. Please refer to the table below for the LAN port LED indications.

Activity/Link LED SPEED LED

Status Description Status Description

LAN Port LED Indications

ACT/LINK LED

SPEED LED

Off No Link Off 10Mbps connection Blinking Data Activity Orange 100Mbps connection On Link

LAN Port

English

on the bottom. In “Advanced Options” screen, select “Independent Headphone”, and click “OK” to save your change.

XP / XP 64-bit OS:

ASRock H61M-HVGS / H61M-HVS Motherboard

1. Introduction

Thank you for purchasing ASRock H61M-HVGS / H61M-HVS motherboard, a reliable motherboard produced under ASRock’s consistently stringent quality control. It delivers excellent performance with robust design conforming to ASRock’s commitment to quality and endurance. This Quick Installation Guide contains introduction of the motherboard and step-bystep installation guide. More detailed information of the motherboard can be found in the user manual presented in the Support CD.

Because the motherboard speciﬁ cations and the BIOS software might be updated, the content of this manual will be subject to change without notice. In case any modiﬁ cations of this manual occur, the updated version will be available on ASRock website without further notice. You may ﬁ nd the latest VGA cards and CPU support lists on ASRock website as well. ASRock website http://www.asrock.com If you require technical support related to this motherboard, please visit our website for speciﬁ c information about the model you are using. www.asrock.com/support/index.asp

1.1 Package Contents

ASRock H61M-HVGS / H61M-HVS Motherboard (Micro ATX Form Factor: 8.9-in x 6.8-in, 22.6 cm x 17.3 cm) ASRock H61M-HVGS / H61M-HVS Quick Installation Guide ASRock H61M-HVGS / H61M-HVS Support CD 2 x Serial ATA (SATA) Data Cables (Optional) 1 x I/O Panel Shield

ASRock Reminds You...

To get better performance in Windows® 7 / 7 64-bit / Vista bit, it is recommended to set the BIOS option in Storage Conﬁ guration to AHCI mode. For the BIOS setup, please refer to the “User Manual” in our support CD for details.

/ VistaTM 64-

ASRock H61M-HVGS / H61M-HVS Motherboard

English

1.2 Specifications

Platform - Micro ATX Form Factor: 8.9-in x 6.8-in, 22.6 cm x 17.3 cm

- Solid Capacitor for CPU power CPU - Supports 2nd Generation Intel LGA1155 Package

- Supports Intel

Turbo Boost 2.0 Technology

- Supports K-Series unlocked CPU

- Supports Hyper-Threading Technology (see CAUTION 1)

Chipset - Intel® H61 Memory - Dual Channel DDR3 Memory Technology (see CAUTION 2)

- 2 x DDR3 DIMM slots

- Supports DDR3 1333/1066 non-ECC, un-buffered memory

- Max. capacity of system memory: 16GB (see CAUTION 3) Expansion Slot - 1 x PCI Express 2.0 x16 slot (blue @ x16 mode)

- 1 x PCI Express 2.0 x1 slot Graphics - Intel

HD Graphics 2000/3000

- Pixel Shader 4.1, DirectX 10.1

- Max. shared memory 1759MB (see CAUTION 4)

- Dual VGA Output: support HDMI and D-Sub ports by independent display controllers

- Supports HDMI 1.4a Technology with max. resolution up to 1920x1200 @ 60Hz

- Supports D-Sub with max. resolution up to 2048x1536 @ 75Hz

- Supports Auto Lip Sync, Deep Color (12bpc), xvYCC and HBR (High Bit Rate Audio) with HDMI (Compliant HDMI monitor is required) (see CAUTION 5)

- Supports Blu-ray Stereoscopic 3D with HDMI 1.4a

- Supports HDCP function with HDMI port

- Supports Full HD 1080p Blu-ray (BD) / HD-DVD playback with HDMI port

Audio - 5.1 CH HD Audio (VIA LAN - H61M-HVGS

Realtek PCIE x1 Gigabit LAN RTL8111E, speed 10/100/1000 Mb/s

- H61M-HVS Realtek PCIE x1 LAN RTL8105E, speed 10/100 Mb/s

- Supports Wake-On-LAN

CoreTM i7 / i5 / i3 in

VT1705 Audio Codec)

ASRock H61M-HVGS / H61M-HVS Motherboard

Rear Panel I/O I/O Panel

- 1 x PS/2 Mouse Port

- 1 x PS/2 Keyboard Port

- 1 x VGA/D-Sub Port

- 1 x HDMI Port

- 6 x Ready-to-Use USB 2.0 Ports

- 1 x RJ-45 LAN Port with LED (ACT/LINK LED and SPEED LED)

- HD Audio Jack: Line in/Front Speaker/Microphone Connector - 4 x SATA2 3.0 Gb/s connectors, support NCQ, AHCI and Hot Plug functions

- 1 x Print Port header

- 1 x COM port header

- CPU/Chassis/Power FAN connector

- 24 pin ATX power connector

- 4 pin 12V power connector

- Front panel audio connector

- 2 x USB 2.0 headers (support 4 USB 2.0 ports) BIOS Feature - 32Mb AMI BIOS

- AMI UEFI Legal BIOS with GUI support

- Supports “Plug and Play”

- ACPI 1.1 Compliance Wake Up Events

- Supports jumperfree

- SMBIOS 2.3.1 Support

- IGPU, DRAM, PCH, CPU PLL, VTT, VCCSA Voltage Multi-adjustment Support CD - Drivers, Utilities, AntiVirus Software (Trial Version), ASRock Software Suite (CyberLink DVD Suite - OEM and Trial; Creative Sound Blaster X-Fi MB - Trial) Unique Feature - ASRock Extreme Tuning Utility (AXTU) (see CAUTION 6)

- Instant Boot

- ASRock Instant Flash (see CAUTION 7)

- ASRock APP Charger (see CAUTION 8)

- SmartView (see CAUTION 9)

- ASRock XFast USB (see CAUTION 10)

- Hybrid Booster:

- ASRock U-COP (see CAUTION 11)

- Boot Failure Guard (B.F.G.)

- Combo Cooler Option (C.C.O.) (see CAUTION 12)

- Good Night LED

English

ASRock H61M-HVGS / H61M-HVS Motherboard

Hardware - CPU Temperature Sensing Monitor - Chassis Temperature Sensing

- CPU/Chassis/Power Fan Tachometer

- CPU/Chassis Quiet Fan (Allow Chassis Fan Speed Auto-Adjust by CPU Temperature)

- CPU/Chassis Fan Multi-Speed Control

- Voltage Monitoring: +12V, +5V, +3.3V, CPU Vcore OS - Microsoft

Windows® 7 / 7 64-bit / Vista

/ VistaTM 64-bit

/ XP / XP 64-bit compliant Certiﬁ cations - FCC, CE, WHQL

- ErP/EuP Ready (ErP/EuP ready power supply is required) (see CAUTION 13)

* For detailed product information, please visit our website: http://www.asrock.com

WARNING

Please realize that there is a certain risk involved with overclocking, including adjusting the setting in the BIOS, applying Untied Overclocking Technology, or using the third-party overclocking tools. Overclocking may affect your system stability, or even cause damage to the components and devices of your system. It should be done at your own risk and expense. We are not responsible for possible damage caused by overclocking.

English

ASRock H61M-HVGS / H61M-HVS Motherboard

CAUTION!

1. About the setting of “Hyper Threading Technology”, please check page 41 of “User Manual” in the support CD.

2. This motherboard supports Dual Channel Memory Technology. Before you implement Dual Channel Memory Technology, make sure to read the installation guide of memory modules on page 15 for proper installation.

3. Due to the operating system limitation, the actual memory size may be less than 4GB for the reservation for system usage under Windows VistaTM / XP. For Windows® OS with 64-bit CPU, there is no such limitation.

4. The maximum shared memory size is deﬁ ned by the chipset vendor and is subject to change. Please check Intel tion.

5. xvYCC and Deep Color are only supported under Windows® 7 64-bit /

7. Deep Color mode will be enabled only if the display supports 12bpc in EDID. HBR is supported under Windows VistaTM.

6. ASRock Extreme Tuning Utility (AXTU) is an all-in-one tool to ﬁ ne-tune different system functions in a user-friendly interface, which is including Hardware Monitor, Fan Control, Overclocking, OC DNA and IES. In Hardware Monitor, it shows the major readings of your system. In Fan Control, it shows the fan speed and temperature for you to adjust. In Overclocking, you are allowed to overclock CPU frequency for optimal system performance. In OC DNA, you can save your OC settings as a proﬁ le and share with your friends. Your friends then can load the OC proﬁ le to their own system to get the same OC settings. In IES (Intelligent Energy Saver), the voltage regulator can reduce the number of output phases to improve efﬁ ciency when the CPU cores are idle without

sacrificing computing performance. Please visit our website for the

operation procedures of ASRock Extreme Tuning Utility (AXTU).

ASRock website: http://www.asrock.com

7. ASRock Instant Flash is a BIOS ﬂ ash utility embedded in Flash ROM. This convenient BIOS update tool allows you to update system BIOS without entering operating systems ﬁ rst like MS-DOS or Windows®. With this utility, you can press <F6> key during the POST or press <F2> key to BIOS setup menu to access ASRock Instant Flash. Just launch this tool and save the new BIOS ﬁ le to your USB ﬂ ash drive, ﬂ oppy disk or hard

drive, then you can update your BIOS only in a few clicks without prepar-

ing an additional ﬂ oppy diskette or other complicated ﬂ ash utility. Please be noted that the USB ﬂ ash drive or hard drive must use FAT32/16/12 ﬁ le system.

website for the latest informa-

7 64-bit / 7 / VistaTM 64-bit /

7 /

English

ASRock H61M-HVGS / H61M-HVS Motherboard

8. If you desire a faster, less restricted way of charging your Apple devices, such as iPhone/iPod/iPad Touch, ASRock has prepared a wonderful

solution for you - ASRock APP Charger. Simply installing the APP Char-

ger driver, it makes your iPhone charged much quickly from your computer and up to 40% faster than before. ASRock APP Charger allows you to quickly charge many Apple devices simultaneously and even supports continuous charging when your PC enters into Standby mode (S1), Suspend to RAM (S3), hibernation mode (S4) or power off (S5). With APP Charger driver installed, you can easily enjoy the marvelous charging experience than ever.

ASRock website: http://www.asrock.com/Feature/AppCharger/index.asp

SmartView, a new function of internet browser, is the smart start page for IE that combines your most visited web sites, your history, your Facebook friends and your real-time newsfeed into an enhanced view for a more personal Internet experience. ASRock motherboards are exclusively equipped with the SmartView utility that helps you keep in touch with friends on-the-go. To use SmartView feature, please make sure your OS version is Windows browser version is IE8. ASRock website: http://www.asrock.com/Feature/

SmartView/index.asp

10. ASRock XFast USB can boost USB storage device performance. The performance may depend on the property of the device.

11. While CPU overheat is detected, the system will automatically shutdown. Before you resume the system, please check if the CPU fan on the motherboard functions properly and unplug the power cord, then plug it back again. To improve heat dissipation, remember to spray thermal

grease between the CPU and the heatsink when you install the PC sys-

tem.

12. Combo Cooler Option (C.C.O.) provides the ﬂ exible option to adopt three different CPU cooler types, Socket LGA 775, LGA 1155 and LGA 1156. Please be noticed that not all the 775 and 1156 CPU Fan can be used.

7 / 7 64 bit / VistaTM / VistaTM 64 bit, and your

English

ASRock H61M-HVGS / H61M-HVS Motherboard

13. EuP, stands for Energy Using Product, was a provision regulated by European Union to deﬁ ne the power consumption for the completed system. According to EuP, the total AC power of the completed system shall be under 1.00W in off mode condition. To meet EuP standard, an EuP ready motherboard and an EuP ready power supply are required. According to Intel’s suggestion, the EuP ready power supply must meet the standard of 5v standby power efﬁ ciency is higher than 50% under 100 mA current consumption. For EuP ready power supply selection, we recommend you checking with the power supply manufacturer for more details.

ASRock H61M-HVGS / H61M-HVS Motherboard

English

2. Installation

Pre-installation Precautions

Take note of the following precautions before you install motherboard components or change any motherboard settings.

1. Unplug the power cord from the wall socket before touching any

component. Failure to do so may cause severe damage to the motherboard, peripherals, and/or components.

2. To avoid damaging the motherboard components due to static

electricity, NEVER place your motherboard directly on the carpet or the like. Also remember to use a grounded wrist strap or touch a safety grounded object before you handle components.

3. Hold components by the edges and do not touch the ICs.

4. Whenever you uninstall any component, place it on a grounded

antstatic pad or in the bag that comes with the component.

5. When placing screws into the screw holes to secure the moth-

erboard to the chassis, please do not over-tighten the screws! Doing so may damage the motherboard.

2.1 CPU Installation

For the installation of Intel 1155-Pin CPU, please follow the steps below.

LoadPlate

LoadLever

English

ContactArray

1155-Pin Socket Overview

Before you insert the 1155-Pin CPU into the socket, please check if the CPU surface is unclean or if there is any bent pin on the socket. Do not force to insert the CPU into the socket if above situation is found. Otherwise, the CPU will be seriously damaged.

SocketBody

ASRock H61M-HVGS / H61M-HVS Motherboard

Step 1. Open the socket:

Step 1-1. Disengaging the lever by depressing

down and out on the hook to clear retention tab.

Step 1-2. Rotate the load lever to fully open po-

sition at approximately 135 degrees.

Step 1-3. Rotate the load plate to fully open po-

sition at approximately 100 degrees.

Step 2. Remove PnP Cap (Pick and Place Cap).

1. It is recommended to use the cap tab to handle and avoid kicking off the PnP cap.

2. This cap must be placed if returning the motherboard for after service.

Step 3. Insert the 1155-Pin CPU:

Step 3-1. Hold the CPU by the edges where

are marked with black lines.

black line

Step 3-2. Orient the CPU with IHS (Integrated

Heat Sink) up. Locate Pin1 and the two orientation key notches.

orientation key notch

Pin1

orientation key notch

1155-Pin CPU

For proper inserting, please ensure to match the two orientation key notches of the CPU with the two alignment keys of the socket.

alignment key

1155-Pin Socket

ASRock H61M-HVGS / H61M-HVS Motherboard

alignment key

Pin1

English

Step 3-3. Carefully place the CPU into the

socket by using a purely vertical motion.

Step 3-4. Verify that the CPU is within the sock-

et and properly mated to the orient keys.

Step 4. Close the socket:

Step 4-1. Rotate the load plate onto the IHS. Step 4-2. While pressing down lightly on load

plate, engage the load lever.

Step 4-3. Secure load lever with load plate tab

under retention tab of load lever.

2.2 Installation of CPU Fan and Heatsink

For proper installation, please kindly refer to the instruction manuals of your CPU fan and heatsink.

Below is an example to illustrate the installation of the heatsink for 1155-Pin CPU. Step 1. Apply thermal interface material onto center of

IHS on the socket surface.

Step 2. Place the heatsink onto the socket. Ensure

fan cables are oriented on side closest to the CPU fan connector on the motherboard (CPU_ FAN1, see page 2, No. 3).

Step 3. Align fasteners with the motherboard through-

holes.

Step 4. Rotate the fastener clockwise, then press

down on fastener caps with thumb to install and lock. Repeat with remaining fasteners.

Fancables on side closestto MB header

PressDown (4Places)

ApplyThermal InterfaceMaterial

Fastenerslots pointingstraight out

English

If you press down the fasteners without rotating them clockwise, the heatsink cannot be secured on the motherboard.

Step 5. Connect fan header with the CPU fan connector on the motherboard. Step 6. Secure excess cable with tie-wrap to ensure cable does not interfere with fan operation or contact other components.

Please be noticed that this motherboard supports Combo Cooler Option (C.C.O.), which provides the ﬂ exible option to adopt three dif- ferent CPU cooler types, Socket LGA 775, LGA 1155 and LGA 1156. The white throughholes are for Socket LGA 1155/1156 CPU fan.

ASRock H61M-HVGS / H61M-HVS Motherboard

2.3 Installation of Memory Modules (DIMM)

This motherboard provides two 240-pin DDR3 (Double Data Rate 3) DIMM slots, and supports Dual Channel Memory Technology. For dual channel configuration, you always need to install two identical (the same brand, speed, size and chiptype) memory modules in the DDR3 DIMM slots to activate Dual Channel Memory Technology. Otherwise, it will operate at single channel mode.

1. It is not allowed to install a DDR or DDR2 memory module into

DDR3 slot;otherwise, this motherboard and DIMM may be damaged.

2. If you install only one memory module or two non-identical memory modules, it is unable to activate the Dual Channel Memory Technology.

3. Some DDR3 1GB double-sided DIMMs with 16 chips may not work on this motherboard. It is not recommended to install them on this motherboard.

Installing a DIMM

Please make sure to disconnect power supply before adding or removing DIMMs or the system components.

Step 1. Unlock a DIMM slot by pressing the retaining clips outward. Step 2. Align a DIMM on the slot such that the notch on the DIMM matches the break on the slot.

notch break

notch

break

damage to the motherboard and the DIMM if you force the DIMM into the slot at incorrect orientation.

The DIMM only ﬁ ts in one correct orientation. It will cause permanent

Step 3. Firmly insert the DIMM into the slot until the retaining clips at both ends fully snap back in place and the DIMM is properly seated.

ASRock H61M-HVGS / H61M-HVS Motherboard

English

2.4 Expansion Slots (PCI Express Slots)

There are 2 PCI Express slots on this motherboard.

PCIE slots: PCIE1 (PCIE x16 slot; Blue) is used for PCI Express x16 lane width

graphics cards.

PCIE2 (PCIE x1 slot; White) is used for PCI Express cards with x1 lane

width cards, such as Gigabit LAN card, SATA2 card, etc.

Installing an expansion card

Step 1. Before installing the expansion card, please make sure that the power

supply is switched off or the power cord is unplugged. Please read the

documentation of the expansion card and make necessary hardware settings for the card before you start the installation. Step 2. Remove the system unit cover (if your motherboard is already installed

in a chassis). Step 3. Remove the bracket facing the slot that you intend to use. Keep the

screws for later use. Step 4. Align the card connector with the slot and press ﬁ rmly until the card is

completely seated on the slot. Step 5. Fasten the card to the chassis with screws. Step 6. Replace the system cover.

English

ASRock H61M-HVGS / H61M-HVS Motherboard

2.5 Dual Monitor and Surround Display Features

Dual Monitor Feature

This motherboard supports dual monitor feature. With the internal VGA output support (HDMI and D-Sub), you can easily enjoy the beneﬁ ts of dual monitor feature without installing any add-on VGA card to this motherboard. This motherboard also provides independent display controllers for HDMI and D-Sub to support dual VGA output so that HDMI and D-sub can drive same or different display contents. To enable dual monitor feature, please follow the below steps:

1. Connect HDMI monitor cable to VGA/HDMI port on the I/O panel, and connect D-Sub monitor cable to VGA/D-Sub port on the I/O panel.

VGA/D-Sub port VGA/HDMI port

2. If you have installed onboard VGA driver from our support CD to your system already, you can freely enjoy the beneﬁ ts of dual monitor function after your system boots. If you haven’t installed onboard VGA driver yet, please install onboard VGA driver from our support CD to your system and restart your computer.

ASRock H61M-HVGS / H61M-HVS Motherboard

English

Surround Display Feature

This motherboard supports surround display upgrade. With the internal VGA output support (HDMI and D-Sub) and external add-on PCI Express VGA cards, you can easily enjoy the beneﬁ ts of surround display feature. Please refer to the following steps to set up a surround display environment:

1. Install the PCI Express VGA card on PCIE1 slot. Please refer to page 16 for proper expansion card installation procedures for details.

2. Connect HDMI monitor cable to VGA/HDMI port on the I/O panel, and connect D-Sub monitor cable to VGA/D-Sub port on the I/O panel. Then connect other monitor cables to the corresponding connectors of the add-on PCI Express VGA card on PCIE1 slot.

3. Boot your system. Press <F2> or <Del> to enter UEFI setup. Enter “Onboard VGA Share Memory” option to adjust the memory capability to [32MB], [64MB], [128MB], [256MB] or [512MB] to enable the function of VGA/D-sub. Please make sure that the value you select is less than the total capability of the system memory. If you do not adjust the UEFI setup, the default value of “Onboard VGA Share Memory”, [Auto], will disable VGA/D-Sub function when the add-on VGA card is inserted to this motherboard.

4. Install the onboard VGA driver and the add-on PCI Express VGA card driver to your system. If you have installed the drivers already, there is no need to install them again.

5. Set up a multi-monitor display.

English

For Windows

XP / XP 64-bit OS:

Right click the desktop, choose “Properties”, and select the “Settings” tab so that you can adjust the parameters of the multi-monitor according to the steps below. A. Click the “Identify” button to display a large number on each monitor. B. Right-click the display icon in the Display Properties dialog that you wish to be your primary monitor, and then select “Primary”. When you use multiple monitors with your card, one monitor will always be Primary, and all additional monitors will be designated as Secondary. C. Select the display icon identiﬁ ed by the number 2. D. Click “Extend my Windows desktop onto this monitor”. E. Right-click the display icon and select “Attached”, if necessary. F. Set the “Screen Resolution” and “Color Quality” as appropriate for the second monitor. Click “Apply” or “OK” to apply these new values. G. Repeat steps C through E for the diaplay icon identiﬁ ed by the number one, two, three and four.

ASRock H61M-HVGS / H61M-HVS Motherboard

For Windows® 7 / 7 64-bit / VistaTM / VistaTM 64-bit OS:

Right click the desktop, choose “Personalize”, and select the “Display Settings” tab so that you can adjust the parameters of the multi-monitor according to the steps below. A. Click the number ”2” icon. B. Click the items “This is my main monitor” and “Extend the desktop onto this monitor”. C. Click “OK” to save your change. D. Repeat steps A through C for the display icon identiﬁ ed by the number three and four.

6. Use Surround Display. Click and drag the display icons to positions representing the physical setup of your monitors that you would like to use. The placement of display icons determines how you move items from one monitor to another.

HDCP Function HDCP function is supported on this motherboard. To use HDCP function with this motherboard, you need to adopt the monitor that supports HDCP function as well. Therefore, you can enjoy the superior display quality with high-deﬁ nition HDCP encryption contents. Please refer to below instruction for more details about HDCP function.

What is HDCP?

HDCP stands for High-Bandwidth Digital Content Protection, a speciﬁ cation developed by Intel

for protecting digital entertainment content that uses the DVI interface. HDCP is a copy protection scheme to eliminate the possibility of intercepting digital data midstream between the video source, or transmitter - such as a computer, DVD player or set-top box and the digital display, or receiver - such as a monitor, television or projector. In other words, HDCP speciﬁ cation is designed to protect the integrity of content as it is being transmitted.

Products compatible with the HDCP scheme such as DVD players, satellite and cable HDTV set-top-boxes, as well as few entertainment PCs requires a secure connection to a compliant display. Due to the increase in manufacturers employing HDCP in their equipment, it is highly recommended that the HDTV or LCD monitor you purchase is compatible.

ASRock H61M-HVGS / H61M-HVS Motherboard

English

2.6 Jumpers Setup

The illustration shows how jumpers are setup. When the jumper cap is placed on pins, the jumper is “Short”. If no jumper cap is placed on pins, the jumper is “Open”. The illustration shows a 3-pin jumper whose pin1 and pin2 are “Short” when jumper cap is placed on these 2 pins.

Jumper Setting Description

Clear CMOS Jumper

(CLRCMOS1) (see p.2, No. 21)

Note: CLRCMOS1 allows you to clear the data in CMOS. To clear and reset the system parameters to default setup, please turn off the computer and unplug

the power cord from the power supply. After waiting for 15 seconds, use a jumper cap to short pin2 and pin3 on CLRCMOS1 for 5 seconds. However, please do not clear the CMOS right after you update the BIOS. If you need to clear the CMOS when you just ﬁ nish updating the BIOS, you must boot up the system ﬁ rst, and then shut it down before you do the clear-CMOS ac- tion. Please be noted that the password, date, time, user default proﬁ le, 1394 GUID and MAC address will be cleared only if the CMOS battery is removed.

Clear CMOSDefault

English

ASRock H61M-HVGS / H61M-HVS Motherboard

2.7 Onboard Headers and Connectors

Onboard headers and connectors are NOT jumpers. Do NOT place jumper caps over these headers and connectors. Placing jumper caps over the headers and connectors will cause permanent damage of the motherboard!

Serial ATAII Connectors These four Serial ATAII

(SATA2_0: see p.2, No. 10)

(SATA2_1: see p.2, No. 8)

(SATA2_2: see p.2, No. 12)

(SATA2_3: see p.2, No. 11)

SATA2_3

(SATAII) connectors support

SATA data cables for internal

storage devices. The current

SATA2_2

SATAII interface allows up to

SATA2_1

SATA2_0

3.0 Gb/s data transfer rate.

Serial ATA (SATA) Either end of the SATA data Data Cable cable can be connected to the

(Optional)

SATA / SATAII hard disk or the SATAII connector on this motherboard.

USB 2.0 Headers Besides six default USB 2.0

(9-pin USB6_7)

(see p.2 No. 15)

ports on the I/O panel, there

are two USB 2.0 headers on this motherboard. Each USB 2.0 header can support two USB 2.0 ports.

(9-pin USB8_9) (see p.2 No. 16)

USB_PWR

P-9

P-8

USB_PWR

P+9

P+8

GND

DUMMY

Print Port Header This is an interface for print

(25-pin LPT1)

(see p.2 No. 18)

port cable that allows

convenient connection of printer devices.

AFD#

STB#

ERROR#

PINIT#

SPD1

SPD0

SLIN#

SPD2

SPD3

SPD4

SPD5

SPD6

GND

SPD7

ACK#

BUSY

SLCT

ASRock H61M-HVGS / H61M-HVS Motherboard

English

Front Panel Audio Header This is an interface for front

(9-pin HD_AUDIO1)

(see p.2 No. 19)

panel audio cable that allows

convenient connection and

control of audio devices.

GND

PRESENCE#

MIC2_R

MIC2_L

MIC_RET

J_SENSE

OUT2_R

OUT_RET

OUT2_L

1. High Deﬁ nition Audio supports Jack Sensing, but the panel wire on the chassis must support HDA to function correctly. Please follow the instruction in our manual and chassis manual to install your system.

2. If you use AC’97 audio panel, please install it to the front panel audio header as below:

A. Connect Mic_IN (MIC) to MIC2_L. B. Connect Audio_R (RIN) to OUT2_R and Audio_L (LIN) to OUT2_L. C. Connect Ground (GND) to Ground (GND). D. MIC_RET and OUT_RET are for HD audio panel only. You don’t

need to connect them for AC’97 audio panel.

System Panel Header This header accommodates

(9-pin PANEL1)

(see p.2 No. 14)

several system front panel

functions.

Connect the power switch, reset switch and system status indicator on the

chassis to this header according to the pin assignments below. Note the positive and negative pins before connecting the cables.

English

PWRBTN (Power Switch): Connect to the power switch on the chassis front panel. You may conﬁ gure

the way to turn off your system using the power switch.

RESET (Reset Switch):

Connect to the reset switch on the chassis front panel. Press the reset

switch to restart the computer if the computer freezes and fails to perform a normal restart.

PLED (System Power LED): Connect to the power status indicator on the chassis front panel. The LED

is on when the system is operating. The LED keeps blinking when the system is in S1 sleep state. The LED is off when the system is in S3/S4 sleep state or powered off (S5).

HDLED (Hard Drive Activity LED): Connect to the hard drive activity LED on the chassis front panel. The LED

is on when the hard drive is reading or writing data.

ASRock H61M-HVGS / H61M-HVS Motherboard

The front panel design may differ by chassis. A front panel module mainly

consists of power switch, reset switch, power LED, hard drive activity LED, speaker and etc. When connecting your chassis front panel module to this header, make sure the wire assignments and the pin assign-ments are matched correctly.

Chassis Speaker Header Please connect the chassis

(4-pin SPEAKER 1)

(see p.2 No. 13)

speaker to this header.

Chassis and Power Fan Connectors Please connect the fan cables

(4-pin CHA_FAN1)

(see p.2 No. 9)

match the black wire to the

to the fan connectors and

CHA_FAN_SPEED

+12V

FAN_SPEED_CONTROL

GND

ground pin.

(3-pin PWR_FAN1) (see p.2 No. 23)

CPU Fan Connectors Please connect the CPU fan

(4-pin CPU_FAN1)

(see p.2 No. 3)

cable to the connector and

match the black wire to the

ground pin.

Though this motherboard provides 4-Pin CPU fan (Quiet Fan) support, the 3-Pin

CPU fan still can work successfully even without the fan speed control function. If you plan to connect the 3-Pin CPU fan to the CPU fan connector on this motherboard, please connect it to Pin 1-3.

ATX Power Connector Please connect an ATX power

(24-pin ATXPWR1)

(see p.2 No. 4)

supply to this connector.

Though this motherboard provides 24-pin ATX power connector, it can still work if you adopt a traditional 20-pin ATX power supply. To use the 20-pin ATX power supply, please plug your power supply along with Pin 1 and Pin 13.

PWR_FAN_SPEED

+12V

GND

4 3 2 1

+12V

FAN_SPEED_CONTROL

CPU_FAN_SPEED

12 124

GND

Pin 1-3 Connected

3-Pin Fan Installation

English

20-Pin ATX Power Supply Installation

ASRock H61M-HVGS / H61M-HVS Motherboard

ATX 12V Power Connector Please connect an ATX 12V

(4-pin ATX12V1)

(see p.2 No. 2)

power supply to this connector.

Serial port Header This COM1 header supports a

(9-pin COM1)

(see p.2 No. 17)

serial port module.

English

ASRock H61M-HVGS / H61M-HVS Motherboard

2.8 Driver Installation Guide

To install the drivers to your system, please insert the support CD to your optical drive ﬁ rst. Then, the drivers compatible to your system can be auto-detected and listed on the support CD driver page. Please follow the order from up to bottom side to install those required drivers. Therefore, the drivers you install can work properly.

2.9 Installing Windows® 7 / 7 64-bit / Vista

/ Vista

64-bit / XP

/ XP 64-bit Without RAID Functions

If you want to install Windows® 7 / 7 64-bit / VistaTM / VistaTM 64-bit / XP / XP 64bit OS on your SATA / SATAII HDDs without RAID functions, please follow below procedures according to the OS you install.

2.9.1 Installing Windows® XP / XP 64-bit Without RAID Functions

If you want to install Windows® XP / XP 64-bit OS on your SATA / SATAII HDDs without RAID functions, please follow below steps.

AHCI mode is not supported under Windows® XP / XP 64-bit OS.

Using SATA / SATAII HDDs without NCQ function

STEP 1: Set up UEFI.

A. Enter UEFI SETUP UTILITY Advanced screen SATA Conﬁ guration. B. Set the option “SATA Mode” to [IDE].

STEP 2: Install Windows

XP / XP 64-bit OS on your system.

ASRock H61M-HVGS / H61M-HVS Motherboard

English

2.9.2 Installing Windows® 7 / 7 64-bit / Vista

/ Vista

64-bit

Without RAID Functions

If you want to install Windows® 7 / 7 64-bit / VistaTM / VistaTM 64-bit OS on your SATA / SATAII HDDs without RAID functions, please follow below steps.

Using SATA / SATAII HDDs with NCQ function

STEP 1: Set Up UEFI.

A. Enter UEFI SETUP UTILITY Advanced screen SATA Conﬁ guration. B. Set the option “SATA Mode” to [AHCI].

STEP 2: Install Windows system.

Using SATA / SATAII HDDs without NCQ function

STEP 1: Set up UEFI.

A. Enter UEFI SETUP UTILITY Advanced screen SATA Conﬁ guration. B. Set the option “SATA Mode” to [IDE].

STEP 2: Install Windows® 7 / 7 64-bit / VistaTM / VistaTM 64-bit OS on your system.

7 / 7 64-bit / VistaTM / VistaTM 64-bit OS on your

English

ASRock H61M-HVGS / H61M-HVS Motherboard

3. BIOS Information

The Flash Memory on the motherboard stores BIOS Setup Utility. When you start up the computer, please press <F2> or <Del> during the Power-On-Self-Test (POST) to enter BIOS Setup utility; otherwise, POST continues with its test routines. If you wish to enter BIOS Setup after POST, please restart the system by pressing <Ctl> + <Alt> + <Delete>, or pressing the reset button on the system chassis. The BIOS Setup program is designed to be user-friendly. It is a menu-driven program, which allows you to scroll through its various sub-menus and to select among the predetermined choices. For the detailed information about BIOS Setup, please refer to the User Manual (PDF ﬁ le) contained in the Support CD.

4. Software Support CD information

This motherboard supports various Microsoft 64-bit / VistaTM / Vista motherboard contains necessary drivers and useful utilities that will enhance motherboard features. To begin using the Support CD, insert the CD into your CD-ROM drive. It will display the Main Menu automatically if “AUTORUN” is enabled in your computer. If the Main Menu does not appear automatically, locate and double-click on the ﬁ le “ASSETUP.EXE” from the BIN folder in the Support CD to display the menus.

64-bit / XP / XP 64-bit. The Support CD that came with the

Windows® operating systems: 7 / 7

ASRock H61M-HVGS / H61M-HVS Motherboard

English

1. Einführung

Wir danken Ihnen für den Kauf des ASRock H61M-HVGS / H61M-HVS Mother- board, ein zuverlässiges Produkt, welches unter den ständigen, strengen Qualitätskontrollen von ASRock gefertigt wurde. Es bietet Ihnen exzellente Leistung und robustes Design, gemäß der Verpﬂ ichtung von ASRock zu Qualität und Halbarkeit. Diese Schnellinstallationsanleitung führt in das Motherboard und die schrittweise Installation ein. Details über das Motherboard ﬁ nden Sie in der Bedienungsanleitung auf der Support-CD.

Da sich Motherboard-Speziﬁ kationen und BIOS-Software verändern können, kann der Inhalt dieses Handbuches ebenfalls jederzeit geändert werden. Für den Fall, dass sich Änderungen an diesem Handbuch ergeben, wird eine neue Version auf der ASRock-Website, ohne weitere Ankündigung, verfügbar sein. Die neuesten Graﬁ kkarten und unterstützten CPUs sind auch auf der ASRock-Website aufgelistet. ASRock-Website: http://www.asrock.com Wenn Sie technische Unterstützung zu Ihrem Motherboard oder speziﬁ sche Informationen zu Ihrem Modell benötigen, besuchen Sie bitte unsere Webseite: www.asrock.com/support/index.asp

1.1 Kartoninhalt

ASRock H61M-HVGS / H61M-HVS Motherboard (Micro ATX-Formfaktor: 22.6 cm x 17.3 cm; 8.9 Zoll x 6.8 Zoll) ASRock H61M-HVGS / H61M-HVS Schnellinstallationsanleitung ASRock H61M-HVGS / H61M-HVS Support-CD Zwei Serial ATA (SATA) -Datenkabel (optional) Ein I/O Shield

Deutsch

ASRock erinnert...

Zur besseren Leistung unter Windows® 7 / 7, 64 Bit / Vista 64 Bit empfehlen wir, die Speicherkonﬁ guration im BIOS auf den AHCI- Modus einzustellen. Hinweise zu den BIOS-Einstellungen ﬁ nden Sie in der Bedienungsanleitung auf der mitgelieferten CD.

/ VistaTM

ASRock H61M-HVGS / H61M-HVS Motherboard

1.2 Spezifikationen

Plattform - Micro ATX-Formfaktor: 22.6 cm x 17.3 cm; 8.9 Zoll x 6.8 Zoll

- Festkondensator für CPU-Leistung CPU - Unterstützt Intel LGA1155-Paket

- Unterstützt Intel

- Unterstützt freigegebene CPU der K-Serie

- Unterstützt Hyper-Threading-Technologie (siehe VORSICHT 1) Chipsatz - Intel

H61

Speicher - Unterstützung von Dual-Kanal-Speichertechnologie (siehe VORSICHT 2)

- 2 x Steckplätze für DDR3

- Unterstützt DDR3 1333/1066 non-ECC, ungepufferter Speicher

- Max. Kapazität des Systemspeichers: 16GB (siehe VORSICHT 3) Erweiterungs- - 1 x PCI Express 2.0 x16-Steckplatz (blau für x16-Modus) steckplätze - 1 x PCI Express 2.0 x1-Steckplätze Onboard-VGA - Intel

HD Graﬁ k 2000/3000

- Pixel Shader 4.1, DirectX 10.1

- Maximal gemeinsam genutzter Speicher 1759MB (siehe VORSICHT 4)

- Doppel-VGA Ausgabe: unterstützt HDMI und D-Sub Ports durch unabhängige Bildschirmanzeige Kontrolleure

- Unterstützt HDMI 1.4a mit einer maximalen Auﬂ ösung von 1920 x 1200 bei 60 Hz

- Unterstützt D-Sub mit einer maximalen Auﬂ ösung von 2048 x 1536 bei 75 Hz

- Unterstützt Auto Lip Sync, Deep Color (12bpc), xvYCC und HBR (High Bit Rate-Audio) mit HDMI (kompatibler HDMI- Bildschirm erforderlich) (siehe VORSICHT 5)

- Unterstützt stereoskopisches 3D per Blu-ray mit HDMI 1.4a

- Unterstützt HDCP-Funktion mit HDMI-Port

- Unterstutzt 1080p Blu-ray (BD) / HD-DVD-Wiedergabe mit HDMI-Port

Audio - 5.1 CH HD Audio (VIA LAN - H61M-HVGS

Realtek PCIE x1 Gigabit LAN RTL8111E, speed 10/100/1000 Mb/s

CoreTM (2te Generation) i7 / i5 / i3 im

Turbo Boost 2.0-Technologie

VT1705 Audio Codec)

Deutsch

ASRock H61M-HVGS / H61M-HVS Motherboard

Deutsch

- H61M-HVS Realtek PCIE x1 LAN RTL8105E, speed 10/100 Mb/s

- Unterstützt Wake-On-LAN E/A-Anschlüsse I/O Panel an der - 1 x PS/2-Mausanschluss Rückseite - 1 x PS/2-Tastaturanschluss

- 1 x VGA/D-Sub port

- 1 x HDMI port

- 6 x Standard-USB 2.0-Anschlüsse

- 1 x RJ-45 LAN Port mit LED (ACT/LINK LED und SPEED LED)

- HD Audiobuchse: Audioeingang / Lautsprecher vorne / Mikrofon Anschlüsse - 4 x SATA2 3,0 GB/s-Anschlüsse, unterstützen NCQ-, AHCI- und „Hot Plug“ (Hot-Plugging)- Funktionen

- 1 x Druckerport-Anschlussleiste

- 1 x COM-Anschluss-Header

- CPU/Gehäuse/Stromlüfter-Anschluss

- 24-pin ATX-Netz-Header

- 4-pin anschluss für 12V-ATX-Netzteil

- Anschluss für Audio auf der Gehäusevorderseite

- 2 x USB 2.0-Anschlüsse (Unterstützung 4 zusätzlicher USB 2.0-Anschlüsse) BIOS - 32Mb AMI BIOS

- AMIs Legal BIOS UEFI mit GUI-Unterstützung

- Unterstützung für “Plug and Play”

- ACPI 1.1-Weckfunktionen

- JumperFree-Übertaktungstechnologie

- SMBIOS 2.3.1

- IGPU, DRAM, PCH, CPU PLL, VTT, VCCSA Stromspannung Multianpassung Support-CD - Treiber, Dienstprogramme, Anti-Virus-Software (Testversion), ASRock Software Suite (CyberLink DVD Suite und Creative Sound Blaster X-Fi MB) (OEM- und Testversion)

Einzigartige - ASRock Extreme Tuning Utility (AXTU) (siehe VORSICHT 6) Eigenschaft - Sofortstart

- ASRock Instant Flash (siehe VORSICHT 7)

- ASRock APP Charger (siehe VORSICHT 8)

- SmartView (siehe VORSICHT 9)

- ASRock XFast USB (siehe VORSICHT 10)

ASRock H61M-HVGS / H61M-HVS Motherboard

+ 116 hidden pages