ASRock H61M-DG3 User Manual [en, ru, de, es, fr, it]

Page 1

No part of this installation guide may be reproduced, transcribed, transmitted, or translated in any language, in any form or by any means, except duplication of documentation by the purchaser for backup purpose, without written consent of ASRock Inc. Products and corporate names appearing in this guide may or may not be registered trademarks or copyrights of their respective companies, and are used only for identiﬁ ca- tion or explanation and to the owners’ beneﬁ t, without intent to infringe.

Disclaimer:

Speciﬁ cations and information contained in this guide are furnished for informational use only and subject to change without notice, and should not be constructed as a commitment by ASRock. ASRock assumes no responsibility for any errors or omissions that may appear in this guide. With respect to the contents of this guide, ASRock does not provide warranty of any kind, either expressed or implied, including but not limited to the implied warranties or conditions of merchantability or ﬁ tness for a particular purpose. In no event shall ASRock, its directors, ofﬁ cers, employees, or agents be liable for any indirect, special, incidental, or consequential damages (including damages for loss of proﬁ ts, loss of business, loss of data, interruption of business and the like), even if ASRock has been advised of the possibility of such damages arising from any defect or error in the guide or product.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that

may cause undesired operation.

CALIFORNIA, USA ONLY

The Lithium battery adopted on this motherboard contains Perchlorate, a toxic substance controlled in Perchlorate Best Management Practices (BMP) regulations passed by the California Legislature. When you discard the Lithium battery in California, USA, please follow the related regulations in advance. “Perchlorate Material-special handling may apply, see www.dtsc.ca.gov/hazardouswaste/perchlorate”

ASRock Website: http://www.asrock.com

Published September 2012

ASRock H61M-DG3/USB3 Motherboard

English

Page 2

Motherboard Layout

17.3cm (6.8in)

Keyboard

Mouse

PS2

ATX12 V1

CPU_FAN1

VGA1

Fast LAN

RoHS

DVI1

22.6cm (8.9in)

USB2.0 T:USB0 B:USB1

USB3.0 T:USB0

B:USB1

USB2.0 T:USB4 B:USB5

Bottom:

MIC IN

Top: RJ-45

Top:

LINE IN

Center:

FRONT

LAN PHY

PWR_FAN1

H61M-DG3/USB3

USB3_2_3

Fast RAM

PCIE1

Fast USB

ErP/EuP Ready DDR3

DDR3_A1 (64bit, 240-pin module)

DDR3_B1 (64bit, 240-pin module)

ATXPWR1

Super

AUDIO CODEC

I/O

HD_AUDIO1

LPT1

PCIE2

CLRCMOS1

CI1

CMOS

Battery

USB8_9

COM1

USB6_7

Intel

H61

SATA2_3

SPEAKER1

PLEDPWRBTN

HDLED RESET

SATA2_2

PANEL1

32Mb BIOS

SATA2_1

CHA_FAN1

SATA2_0

Front USB3.0

English

1 ATX 12V Power Connector (ATX12V1) 13 Chassis Speaker Header (SPEAKER1) 2 1155-Pin CPU Socket 14 System Panel Header (PANEL1) 3 CPU Fan Connector (CPU_FAN1) 15 USB 2.0 Header (USB6_7) 4 ATX Power Connector (ATXPWR1) 16 USB 2.0 Header (USB8_9) 5 2 x 240-pin DDR3 DIMM Slots 17 COM Port Header (COM1) (Dual Channel: DDR3_A1, DDR3_B1) 18 Print Port Header (LPT1) 6 Intel H61 Chipset 19 Front Panel Audio Header (HD_AUDIO1) 7 32Mb SPI Flash 20 PCI Express 2.0 x1 Slot (PCIE2) 8 SATA2 Connector (SATA2_1) 21 Clear CMOS Jumper (CLRCMOS1) 9 Chassis Fan Connector (CHA_FAN1) 22 Chassis Intrusion Header (CI1) 10 SATA2 Connector (SATA2_0) 23 PCI Express 2.0 x16 Slot (PCIE1) 11 SATA2 Connector (SATA2_3) 24 USB 3.0 Header (USB3_2_3) 12 SATA2 Connector (SATA2_2) 25 Power Fan Connector (PWR_FAN1)

ASRock H61M-DG3/USB3 Motherboard

Page 3

I/O Panel

1 PS/2 Mouse Port (Green) 7 USB 3.0 Ports (USB3_0_1) * 2 LAN RJ-45 Port 8 USB 2.0 Ports (USB01) 3 Line In (Light Blue) 9 DVI-D Port (DVI1) ** 4 Front Speaker (Lime) 10 D-Sub Port (VGA1) 5 Microphone (Pink) 11 PS/2 Keyboard Port (Purple) 6 USB 2.0 Ports (USB45)

* There are two LED next to the LAN port. Please refer to the table below for the LAN port LED indications.

Activity/Link LED SPEED LED

Status Description Status Description

LAN Port LED Indications

ACT/LINK LED

SPEED LED

Off No Link Off 10Mbps connection Blinking Data Activity Orange 100Mbps connection On Link Green 1Gbps connection

** To enable Multi-Streaming function, you need to connect a front panel audio cable to the front panel audio header. Please refer to below steps for the software setting of Multi-Streaming. For Windows® XP: After restarting your computer, you will ﬁ nd “Mixer” tool on your system. Please select “Mixer ToolBox” , click “Enable playback multi-streaming”, and click “ok”. Choose “2CH” or

LAN Port

“4CH” and then you are allowed to select “Realtek HDA Primary output” to use Rear Speaker and Front Speaker, or select “Realtek HDA Audio 2nd output” to use front panel audio. Then reboot your system. For Windows After restarting your computer, please double-click “Realtek HD Audio Manager” on the system tray. Set “Speaker Conﬁ guration” to “Quadraphonic” or “Stereo”. Click “Device advanced settings”, choose “Make front and rear output devices playbacks two different audio streams simultaneously”, and click “ok”. Then reboot your system.

7 / VistaTM:

ASRock H61M-DG3/USB3 Motherboard

English

Page 4

1. Introduction

Thank you for purchasing ASRock H61M-DG3/USB3 motherboard, a reliable motherboard produced under ASRock’s consistently stringent quality control. It delivers excellent performance with robust design conforming to ASRock’s commitment to quality and endurance. This Quick Installation Guide contains introduction of the motherboard and step-bystep installation guide. More detailed information of the motherboard can be found in the user manual presented in the Support CD.

Because the motherboard speciﬁ cations and the BIOS software might be updated, the content of this manual will be subject to change without notice. In case any modiﬁ cations of this manual occur, the updated version will be available on ASRock website without further notice. You may ﬁ nd the latest VGA cards and CPU support lists on ASRock website as well. ASRock website http://www.asrock.com If you require technical support related to this motherboard, please visit our website for speciﬁ c information about the model you are using. www.asrock.com/support/index.asp

1.1 Package Contents

ASRock H61M-DG3/USB3 Motherboard (Micro ATX Form Factor: 8.9-in x 6.8-in, 22.6 cm x 17.3 cm) ASRock H61M-DG3/USB3 Quick Installation Guide ASRock H61M-DG3/USB3 Support CD 2 x Serial ATA (SATA) Data Cables (Optional) 1 x I/O Panel Shield

English

ASRock Reminds You...

To get better performance in Windows® 7 / 7 64-bit / Vista bit, it is recommended to set the BIOS option in Storage Conﬁ guration to AHCI mode.

/ VistaTM 64-

ASRock H61M-DG3/USB3 Motherboard

Page 5

1.2 Speciﬁ cations

Platform - Micro ATX Form Factor: 8.9-in x 6.8-in, 22.6 cm x 17.3 cm

- All Solid Capacitor design CPU - Supports 2nd Generation Intel LGA1155 Package

- Supports Intel

Turbo Boost 2.0 Technology

- Supports K-Series unlocked CPU Chipset - Intel® H61

- Supports Intel® Rapid Start Technology and Smart Connect Technology Memory - Dual Channel DDR3 Memory Technology

- 2 x DDR3 DIMM slots

- Supports DDR3 1600/1333/1066 non-ECC, un-buffered memory (DDR3 1600 with Intel DDR3 1333 with Intel® Sandy Bridge CPU)

- Max. capacity of system memory: 16GB (see CAUTION 1)

- Supports Intel

Extreme Memory Proﬁ le (XMP) 1.3 / 1.2 with

Intel® Ivy Bridge CPU Expansion Slot - 1 x PCI Express 3.0 x16 slot

* PCIE 3.0 is only supported with Intel® Ivy Bridge CPU. With Intel® Sandy Bridge CPU, it only supports PCIE 2.0.

- 1 x PCI Express 2.0 x1 slot Graphics * Intel

HD Graphics Built-in Visuals and the VGA outputs can be supported only with processors which are GPU integrated.

- Supports Intel

HD Graphics Built-in Visuals: Intel® Quick Sync Video 2.0, Intel® InTruTM 3D, Intel® Clear Video HD Technology, Intel® InsiderTM, Intel® HD Graphics 2500/4000 with Intel® Ivy Bridge CPU

- Supports Intel

HD Graphics Built-in Visuals: Intel® Quick Sync Video, Intel® InTruTM 3D, Intel® Clear Video HD Technology, Intel® HD Graphics 2000/3000, Intel® Advanced Vector Extensions (AVX) with Intel® Sandy Bridge CPU

- Pixel Shader 5.0, DirectX 11 with Intel® Ivy Bridge CPU. Pixel Shader 4.1, DirectX 10.1 with Intel CPU.

- Max. shared memory 1760MB with Intel Max. shared memory 1759MB with Intel® Sandy Bridge CPU.

CoreTM i7 / i5 / i3 in

Ivy Bridge CPU,

Sandy Bridge

Ivy Bridge CPU.

English

ASRock H61M-DG3/USB3 Motherboard

Page 6

English

- Dual VGA Output: support DVI-D and D-Sub ports by independent display controllers

- Supports DVI with max. resolution up to 1920x1200 @ 60Hz

- Supports D-Sub with max. resolution up to 2048x1536 @ 75Hz

- Supports HDCP function with DVI port

- Supports Full HD 1080p Blu-ray (BD) / HD-DVD playback with DVI port

Audio - 5.1 CH HD Audio (Realtek ALC662 Audio Codec) LAN - PCIE x1 Gigabit LAN 10/100/1000 Mb/s

- Realtek RTL8111E

- Supports Wake-On-LAN

- Supports LAN Cable Detection

- Supports Energy Efﬁ cient Ethernet 802.3az

- Supports PXE Rear Panel I/O I/O Panel

- 1 x PS/2 Mouse Port

- 1 x PS/2 Keyboard Port

- 1 x D-Sub Port

- 1 x DVI-D Port

- 4 x Ready-to-Use USB 2.0 Ports

- 2 x Ready-to-Use USB 3.0 Ports

- 1 x RJ-45 LAN Port with LED (ACT/LINK LED and SPEED LED)

- HD Audio Jack: Line in/Front Speaker/Microphone USB 3.0 - 2 x Rear USB 3.0 ports by Etron EJ188H, support USB 1.1/2.0/3.0 up to 5Gb/s

- 1 x Front USB 3.0 header by Etron EJ188H (supports 2 USB 3.0 ports), supports USB 1.1/2.0/3.0 up to 5Gb/s Connector - 4 x SATA2 3.0 Gb/s connectors, support NCQ, AHCI and Hot Plug functions

- 1 x Print Port header

- 1 x COM port header

- 1 x Chassis Intrusion header

- 1 x CPU Fan connector (4-pin)

- 1 x Chassis Fan connector (4-pin)

- 1 x Power Fan connector (3-pin)

- 24 pin ATX power connector

- 4 pin 12V power connector

- Front panel audio connector

- 2 x USB 2.0 headers (support 4 USB 2.0 ports)

ASRock H61M-DG3/USB3 Motherboard

Page 7

- 1 x USB 3.0 header (supports 2 USB 3.0 ports) BIOS Feature - 32Mb AMI UEFI Legal BIOS with GUI support

- Supports “Plug and Play”

- ACPI 1.1 Compliance Wake Up Events

- Supports jumperfree

- SMBIOS 2.3.1 Support

- IGPU, DRAM, PCH, CPU PLL, VTT, VCCSA Voltage Multi-adjustment Support CD - Drivers, Utilities, AntiVirus Software (Trial Version), CyberLink MediaEspresso 6.5 Trial, ASRock MAGIX Multimedia Suite - OEM Hardware - CPU Temperature Sensing Monitor - Chassis Temperature Sensing

- CPU/Chassis/Power Fan Tachometer

- CPU/Chassis Quiet Fan (Allow Chassis Fan Speed Auto-Adjust by CPU Temperature)

- CPU/Chassis Fan Multi-Speed Control

- CASE OPEN detection

- Voltage Monitoring: +12V, +5V, +3.3V, CPU Vcore OS - Microsoft

Windows® 7 / 7 64-bit / Vista

/ VistaTM 64-bit

/ XP / XP 64-bit compliant (see CAUTION 2) Certiﬁ cations - FCC, CE, WHQL

- ErP/EuP Ready (ErP/EuP ready power supply is required)

* For detailed product information, please visit our website: http://www.asrock.com

WARNING

Please realize that there is a certain risk involved with overclocking, including adjusting the setting in the BIOS, applying Untied Overclocking Technology, or using third-party overclocking tools. Overclocking may affect your system’s stability, or even cause damage to the components and devices of your system. It should be done at your own risk and expense. We are not responsible for possible damage caused by overclocking.

ASRock H61M-DG3/USB3 Motherboard

English

Page 8

CAUTION!

1. Due to the operating system limitation, the actual memory size may be less than 4GB for the reservation for system usage under Windows CPU, there is no such limitation. You can use ASRock XFast

RAM to utilize the memory that Windows® cannot use.

2. ASRock XFast RAM is not supported by Microsoft® Windows® XP / XP 64-bit.

7 / VistaTM / XP. For Windows® OS with 64-bit

English

ASRock H61M-DG3/USB3 Motherboard

Page 9

1.3 Unique Features

ASRock Extreme Tuning Utility (AXTU)

ASRock Extreme Tuning Utility (AXTU) is an all-in-one tool to

ne-tune different system functions in a user-friendly interface, which includes Hardware Monitor, Fan Control, Overclocking, OC DNA, IES and XFast RAM. In Hardware Monitor, it shows the major readings of your system. In Fan Control, it shows the fan speed and temperature for you to adjust. In Overclocking, you are allowed to overclock CPU frequency for optimal system performance. In OC DNA, you can save your OC settings as a proﬁ le and share it with your friends. Your friends then can load the OC proﬁ le to their own system to get the same OC set- tings. In IES (Intelligent Energy Saver), the voltage regulator can reduce the number of output phases to improve efﬁ ciency when the CPU cores are idle without sacriﬁ cing computing per- formance. In

cannot be used under Windows® OS 32-bit CPU.

ASRock Instant Boot

ASRock Instant Boot allows you to turn on your PC in just a few

seconds, provides a much more efﬁ cient way to save energy, time, money, and improves system running speed for your system. It leverages the S3 and S4 ACPI features which normally enable the Sleep/Standby and Hibernation modes in Windows to shorten boot up time. By calling S3 and S4 at speciﬁ c timing during the shutdown and startup process, Instant Boot allows you to enter your Windows

XFast RAM, it fully utilizes the memory space that

desktop in a few seconds.

ASRock Instant Flash

ASRock Instant Flash is a BIOS ﬂ ash utility embedded in Flash

ROM. This convenient BIOS update tool allows you to update system BIOS without entering operating systems ﬁ rst like MS- DOS or Windows

. With this utility, you can press the <F6> key during the POST or the <F2> key to enter into the BIOS setup menu to access ASRock Instant Flash. Just launch this tool and save the new BIOS ﬁ le to your USB ﬂ ash drive, ﬂ oppy disk or hard drive, then you can update your BIOS only in a few clicks without preparing an additional ﬂ oppy diskette or other compli- cated ﬂ ash utility. Please be noted that the USB ﬂ ash drive or hard drive must use FAT32/16/12 ﬁ le system.

ASRock H61M-DG3/USB3 Motherboard

English

Page 10

ASRock APP Charger

If you desire a faster, less restricted way of charging your

Apple devices, such as iPhone/iPad/iPod Touch, ASRock has prepared a wonderful solution for you - ASRock APP Charger. Simply install the APP Charger driver, it makes your iPhone charge much quickly from your computer and up to 40% faster than before. ASRock APP Charger allows you to quickly charge many Apple devices simultaneously and even supports continuous charging when your PC enters into Standby mode (S1), Suspend to RAM (S3), hibernation mode (S4) or power off (S5). With APP Charger driver installed, you can easily enjoy the marvelous charging experience.

ASRock XFast USB

ASRock XFast USB can boost USB storage device perfor-

mance. The performance may depend on the properties of the device.

ASRock XFast LAN

ASRock XFast LAN provides a faster internet access, which

includes the benefits listed below. LAN Application Prioritization: You can conﬁ gure your application’s priority ideally and/or add new programs. Lower Latency in Game: After setting online game’s priority higher, it can lower the latency in games. Trafﬁ c Shaping: You can watch Youtube HD videos and download simultaneously. Real-Time Analysis of Your Data: With the status window, you can easily recognize which data streams you are transferring currently.

English

ASRock XFast RAM

ASRock XFast RAM is a new function that is included into ASRock Extreme Tuning Utility (AXTU). It fully utilizes the memory space that cannot be used under Windows® OS 32-bit CPU. ASRock XFast RAM shortens the loading time of previously visited websites, making web surfing faster than ever. And it also boosts the speed of Adobe Photoshop 5 times faster. Another advantage of ASRock XFast RAM is that it reduces the frequency of accessing your SSDs or HDDs in order to extend their lifespan.

ASRock H61M-DG3/USB3 Motherboard

Page 11

ASRock Crashless BIOS

ASRock Crashless BIOS allows users to update their BIOS

without fear of failing. If power loss occurs during the BIOS update process, ASRock Crashless BIOS will automatically ﬁ nish the BIOS update procedure after regaining power. Please note that BIOS ﬁ les need to be placed in the root directory of your USB disk. Only USB2.0 ports support this feature.

ASRock OMG (Online Management Guard)

Administrators are able to establish an internet curfew or restrict

internet access at speciﬁ ed times via OMG. You may schedule the starting and ending hours of internet access granted to other users. In order to prevent users from bypassing OMG, guest accounts without permission to modify the system time are required.

ASRock Internet Flash

ASRock Internet Flash searches for available UEFI firmware

updates from our servers. In other words, the system can autodetect the latest UEFI from our servers and ﬂ ash them without entering Windows

OS. Please note that you must be running

on a DHCP conﬁ gured computer in order to enable this function.

ASRock Fast Boot

With ASRock’s exclusive Fast Boot technology, it takes less

than 1.5 seconds to logon to Windows 8 from a cold boot. No more waiting! The speedy boot will completely change your user experience and behavior.

ASRock Combo Cooler Option (C.C.O.)

Combo Cooler Option (C.C.O.) provides the ﬂ exible option to

adopt three different CPU cooler types, Socket LGA 775, LGA 1155 and LGA 1156. Please be noticed that not all the 775 and 1156 CPU Fan can be used.

ASRock H61M-DG3/USB3 Motherboard

English

Page 12

2. Installation

Pre-installation Precautions

Take note of the following precautions before you install motherboard components or change any motherboard settings.

1. Unplug the power cord from the wall socket before touching any component. Failure to do so may cause severe damage to the motherboard, peripherals, and/or components.

2. To avoid damaging the motherboard components due to static electricity, NEVER place your motherboard directly on the carpet or the like. Also remember to use a grounded wrist strap or touch a safety grounded object before you handle components.

3. Hold components by the edges and do not touch the ICs.

4. Whenever you uninstall any component, place it on a grounded antstatic pad or in the bag that comes with the component.

5. When placing screws into the screw holes to secure the motherboard to the chassis, please do not over-tighten the screws! Doing so may damage the motherboard.

2.1 CPU Installation

For the installation of Intel 1155-Pin CPU, please follow the steps below.

LoadPlate

LoadLever

English

ContactArray

1155-Pin Socket Overview

Before you insert the 1155-Pin CPU into the socket, please check if the CPU surface is unclean or if there is any bent pin on the socket. Do not force to insert the CPU into the socket if above situation is found. Otherwise, the CPU will be seriously damaged.

SocketBody

ASRock H61M-DG3/USB3 Motherboard

Page 13

Step 1. Open the socket:

Step 1-1. Disengaging the lever by depressing

down and out on the hook to clear retention tab.

Step 1-2. Rotate the load lever to fully open po-

sition at approximately 135 degrees.

Step 1-3. Rotate the load plate to fully open po-

sition at approximately 100 degrees.

Step 2. Remove PnP Cap (Pick and Place Cap).

1. It is recommended to use the cap tab to handle and avoid kicking off the PnP cap.

2. This cap must be placed if returning the motherboard for after service.

Step 3. Insert the 1155-Pin CPU:

Step 3-1. Hold the CPU by the edges where

are marked with black lines.

black line

Step 3-2. Orient the CPU with IHS (Integrated

Heat Sink) up. Locate Pin1 and the two orientation key notches.

orientation key notch

Pin1

orientation key notch

1155-Pin CPU

For proper inserting, please ensure to match the two orientation key notches of the CPU with the two alignment keys of the socket.

alignment key

1155-Pin Socket

ASRock H61M-DG3/USB3 Motherboard

alignment key

Pin1

English

Page 14

Step 3-3. Carefully place the CPU into the

socket by using a purely vertical motion.

Step 3-4. Verify that the CPU is within the sock-

et and properly mated to the orient keys.

Step 4. Close the socket:

Step 4-1. Rotate the load plate onto the IHS. Step 4-2. While pressing down lightly on load

plate, engage the load lever.

Step 4-3. Secure load lever with load plate tab

under retention tab of load lever.

2.2 Installation of CPU Fan and Heatsink

For proper installation, please kindly refer to the instruction manuals of your CPU fan and heatsink.

Below is an example to illustrate the installation of the heatsink for 1155-Pin CPU. Step 1. Apply thermal interface material onto center of

IHS on the socket surface.

Step 2. Place the heatsink onto the socket. Ensure

fan cables are oriented on side closest to the CPU fan connector on the motherboard (CPU_ FAN1, see page 2, No. 3).

Step 3. Align fasteners with the motherboard through-

holes.

Step 4. Rotate the fastener clockwise, then press

down on fastener caps with thumb to install and lock. Repeat with remaining fasteners.

Fancables on side closestto MB header

PressDown (4Places)

ApplyThermal InterfaceMaterial

Fastenerslots pointingstraight out

English

If you press down the fasteners without rotating them clockwise, the heatsink cannot be secured on the motherboard.

Step 5. Connect fan header with the CPU fan connector on the motherboard. Step 6. Secure excess cable with tie-wrap to ensure cable does not interfere with fan operation or contact other components.

Please be noticed that this motherboard supports Combo Cooler Option (C.C.O.), which provides the ﬂ exible option to adopt three dif- ferent CPU cooler types, Socket LGA 775, LGA 1155 and LGA 1156. The white throughholes are for Socket LGA 1155/1156 CPU fan.

ASRock H61M-DG3/USB3 Motherboard

Page 15

2.3 Installation of Memory Modules (DIMM)

This motherboard provides two 240-pin DDR3 (Double Data Rate 3) DIMM slots, and supports Dual Channel Memory Technology. For dual channel configuration, you always need to install two identical (the same brand, speed, size and chiptype) memory modules in the DDR3 DIMM slots to activate Dual Channel Memory Technology. Otherwise, it will operate at single channel mode.

1. It is not allowed to install a DDR or DDR2 memory module into

DDR3 slot;otherwise, this motherboard and DIMM may be damaged.

2. If you install only one memory module or two non-identical memory modules, it is unable to activate the Dual Channel Memory Technology.

3. Some DDR3 1GB double-sided DIMMs with 16 chips may not work on this motherboard. It is not recommended to install them on this motherboard.

Installing a DIMM

Please make sure to disconnect power supply before adding or removing DIMMs or the system components.

Step 1. Unlock a DIMM slot by pressing the retaining clips outward. Step 2. Align a DIMM on the slot such that the notch on the DIMM matches the break on the slot.

notch break

notch

break

The DIMM only ﬁ ts in one correct orientation. It will cause permanent damage to the motherboard and the DIMM if you force the DIMM into the slot at incorrect orientation.

Step 3. Firmly insert the DIMM into the slot until the retaining clips at both ends fully snap back in place and the DIMM is properly seated.

ASRock H61M-DG3/USB3 Motherboard

English

Page 16

2.4 Expansion Slots (PCI Express Slots)

There are 2 PCI Express slots on this motherboard.

PCIE slots: PCIE1 (PCIE x16 slot) is used for PCI Express x16 lane width graphics

cards.

PCIE2 (PCIE x1 slot) is used for PCI Express cards with x1 lane width

cards, such as Gigabit LAN card, SATA2 card, etc.

Installing an expansion card

Step 1. Before installing the expansion card, please make sure that the power

supply is switched off or the power cord is unplugged. Please read the

documentation of the expansion card and make necessary hardware settings for the card before you start the installation. Step 2. Remove the system unit cover (if your motherboard is already installed

in a chassis). Step 3. Remove the bracket facing the slot that you intend to use. Keep the

screws for later use. Step 4. Align the card connector with the slot and press ﬁ rmly until the card is

completely seated on the slot. Step 5. Fasten the card to the chassis with screws. Step 6. Replace the system cover.

English

ASRock H61M-DG3/USB3 Motherboard

Page 17

2.5 Jumpers Setup

The illustration shows how jumpers are setup. When the jumper cap is placed on pins, the jumper is “Short”. If no jumper cap is placed on pins, the jumper is “Open”. The illustration shows a 3-pin jumper whose pin1 and pin2 are “Short” when jumper cap is placed on these 2 pins.

Jumper Setting Description

Clear CMOS Jumper

(CLRCMOS1) (see p.2, No. 21)

Note: CLRCMOS1 allows you to clear the data in CMOS. To clear and reset the system parameters to default setup, please turn off the computer and unplug

the power cord from the power supply. After waiting for 15 seconds, use a jumper cap to short pin2 and pin3 on CLRCMOS1 for 5 seconds. However, please do not clear the CMOS right after you update the BIOS. If you need to clear the CMOS when you just ﬁ nish updating the BIOS, you must boot up the system ﬁ rst, and then shut it down before you do the clear-CMOS ac- tion. Please be noted that the password, date, time, user default proﬁ le, 1394 GUID and MAC address will be cleared only if the CMOS battery is removed.

Clear CMOSDefault

If you clear the CMOS, the case open may be detected. Please adjust

the BIOS option “Clear Status” to clear the record of previous chassis intrusion status.

ASRock H61M-DG3/USB3 Motherboard

English

Page 18

2.6 Onboard Headers and Connectors

Onboard headers and connectors are NOT jumpers. Do NOT place jumper caps over these headers and connectors. Placing jumper caps over the headers and connectors will cause permanent damage of the motherboard!

Serial ATA2 Connectors These four Serial ATA2

(SATA2_0: see p.2, No. 10)

(SATA2_1: see p.2, No. 8)

(SATA2_2: see p.2, No. 12)

(SATA2_3: see p.2, No. 11)

SATA2_3

(SATA2) connectors support

SATA data cables for internal

storage devices. The current

SATA2_2

SATA2 interface allows up to

SATA2_1

SATA2_0

3.0 Gb/s data transfer rate.

Serial ATA (SATA) Either end of the SATA data Data Cable cable can be connected to the

(Optional)

SATA / SATA2 hard disk or the SATA2 connector on this motherboard.

USB 2.0 Headers Besides four default USB 2.0

(9-pin USB6_7)

(see p.2 No. 15)

ports on the I/O panel, there

are two USB 2.0 headers on this motherboard. Each USB 2.0 header can support two USB 2.0 ports.

(9-pin USB8_9) (see p.2 No. 16)

USB_PWR

P-9

P-8

USB_PWR

P+9

P+8

GND

DUMMY

English

USB 3.0 Header Besides two default USB 3.0

(19-pin USB3_2_3)

(see p.2, No. 24)

ports on the I/O panel, there is

one USB 3.0 header on this motherboard. This USB 3.0 header can support two USB 3.0 ports.

Vbus

IntA_P0_SSRX-

IntA_P0_SSRX+

GND

IntA_P0_SSTX-

IntA_P0_SSTX+

GND

IntA_P0_D-

IntA_P0_D+

VbusVbus

IntA_P1_SSRX-

IntA_P1_SSRX+

GND

IntA_P1_SSTX-

IntA_P1_SSTX+

GND

IntA_P1_D-

IntA_P1_D+

DUMMY

ASRock H61M-DG3/USB3 Motherboard

Page 19

Print Port Header This is an interface for print

(25-pin LPT1)

(see p.2 No. 18)

port cable that allows

convenient connection of printer

devices.

AFD#

STB#

ERROR#

PINIT#

SPD1

SPD0

SLIN#

SPD2

SPD3

SPD4

SPD5

SPD6

GND

SPD7

ACK#

BUSY

SLCT

GND

PRESENCE#

MIC2_R

MIC2_L

MIC_RET

J_SENSE

OUT2_R

OUT_RET

OUT2_L

Front Panel Audio Header This is an interface for front

(9-pin HD_AUDIO1)

(see p.2 No. 19)

panel audio cable that allows

convenient connection and

control of audio devices.

1. High Deﬁ nition Audio supports Jack Sensing, but the panel wire on the chassis must support HDA to function correctly. Please follow the instruction in our manual and chassis manual to install your system.

2. If you use AC’97 audio panel, please install it to the front panel audio header as below:

A. Connect Mic_IN (MIC) to MIC2_L. B. Connect Audio_R (RIN) to OUT2_R and Audio_L (LIN) to OUT2_L. C. Connect Ground (GND) to Ground (GND). D. MIC_RET and OUT_RET are for HD audio panel only. You don’t

need to connect them for AC’97 audio panel.

E. To activate the front mic. For Windows

XP / XP 64-bit OS:

Select “Mixer”. Select “Recorder”. Then click “FrontMic”.

For Windows® 7 / 7 64-bit / VistaTM / VistaTM 64-bit OS: Go to the "FrontMic" Tab in the Realtek Control panel. Adjust

“Recording Volume”.

System Panel Header This header accommodates

(9-pin PANEL1)

(see p.2 No. 14)

several system front panel

functions.

Connect the power switch, reset switch and system status indicator on the

chassis to this header according to the pin assignments below. Note the positive and negative pins before connecting the cables.

PWRBTN (Power Switch): Connect to the power switch on the chassis front panel. You may conﬁ gure

the way to turn off your system using the power switch.

ASRock H61M-DG3/USB3 Motherboard

English

Page 20

RESET (Reset Switch):

Connect to the reset switch on the chassis front panel. Press the reset

switch to restart the computer if the computer freezes and fails to perform a normal restart.

PLED (System Power LED): Connect to the power status indicator on the chassis front panel. The LED

is on when the system is operating. The LED keeps blinking when the system is in S1 sleep state. The LED is off when the system is in S3/S4 sleep state or powered off (S5).

HDLED (Hard Drive Activity LED): Connect to the hard drive activity LED on the chassis front panel. The LED

is on when the hard drive is reading or writing data.

The front panel design may differ by chassis. A front panel module mainly

consists of power switch, reset switch, power LED, hard drive activity LED, speaker and etc. When connecting your chassis front panel module to this header, make sure the wire assignments and the pin assign-ments are matched correctly.

Chassis Speaker Header Please connect the chassis

(4-pin SPEAKER 1)

(see p.2 No. 13)

speaker to this header.

Chassis and Power Fan Connectors Please connect the fan cables

(4-pin CHA_FAN1)

(see p.2 No. 9)

to the fan connectors and

match the black wire to the

ground pin.

(3-pin PWR_FAN1) (see p.2 No. 25)

GND +12V PWR_FAN_SPEED

English

CPU Fan Connectors Please connect the CPU fan

(4-pin CPU_FAN1)

(see p.2 No. 3)

cable to the connector and

match the black wire to the

ground pin.

4 3 2 1

+12V

FAN_SPEED_CONTROL

CPU_FAN_SPEED

GND

Though this motherboard provides 4-Pin CPU fan (Quiet Fan) support, the 3-Pin

CPU fan still can work successfully even without the fan speed control function. If you plan to connect the 3-Pin CPU fan to the CPU fan connector on this motherboard, please connect it to Pin 1-3.

Pin 1-3 Connected

3-Pin Fan Installation

ASRock H61M-DG3/USB3 Motherboard

Page 21

ATX Power Connector Please connect an ATX power

(24-pin ATXPWR1)

(see p.2 No. 4)

supply to this connector.

12 124

Though this motherboard provides 24-pin ATX power connector,

it can still work if you adopt a traditional 20-pin ATX power supply. To use the 20-pin ATX power supply, please plug your power supply along with Pin 1 and Pin 13.

20-Pin ATX Power Supply Installation

ATX 12V Power Connector Please connect an ATX 12V

(4-pin ATX12V1)

(see p.2 No. 1)

power supply to this connector.

Serial port Header This COM1 header supports a

(9-pin COM1)

(see p.2 No. 17)

serial port module.

Chassis Intrusion Header This motherboard supports

(2-pin CI1)

CASE OPEN detection feature

(see p.2, No. 22)

that detects if the chassis cover

Signal

GND

has been removed. This feature requires a chassis with chassis intrusion detection design.

ASRock H61M-DG3/USB3 Motherboard

English

Page 22

2.7 Driver Installation Guide

To install the drivers to your system, please insert the support CD to your optical drive ﬁ rst. Then, the drivers compatible to your system can be auto-detected and listed on the support CD driver page. Please follow the order from up to bottom side to install those required drivers. Therefore, the drivers you install can work properly.

2.8 Installing Windows® 7 / 7 64-bit / Vista

/ Vista

64-bit /

XP / XP 64-bit Without RAID Functions

If you want to install Windows® 7 / 7 64-bit / VistaTM / VistaTM 64-bit / XP / XP 64bit OS on your SATA / SATA2 HDDs without RAID functions, please follow below procedures according to the OS you install.

2.8.1 Installing Windows® XP / XP 64-bit Without RAID Functions

If you want to install Windows® XP / XP 64-bit OS on your SATA / SATA2 HDDs without RAID functions, please follow below steps.

Using SATA / SATA2 HDDs without NCQ function

STEP 1: Set up UEFI.

A. Enter UEFI SETUP UTILITY Advanced screen Storage Conﬁ guration. B. Set the option “SATA Mode Selection” to [IDE].

STEP 2: Install Windows

2.8.2 Installing Windows® 7 / 7 64-bit / Vista

XP / XP 64-bit OS on your system.

/ Vista

64-bit

Without RAID Functions

If you want to install Windows® 7 / 7 64-bit / VistaTM / VistaTM 64-bit OS on your SATA / SATA2 HDDs without RAID functions, please follow below steps.

English

Using SATA / SATA2 HDDs without NCQ function

STEP 1: Set up UEFI.

A. Enter UEFI SETUP UTILITY Advanced screen Storage Conﬁ guration. B. Set the option “SATA Mode Selection” to [IDE].

STEP 2: Install Windows system.

7 / 7 64-bit / VistaTM / VistaTM 64-bit OS on your

ASRock H61M-DG3/USB3 Motherboard

Page 23

Using SATA / SATA2 HDDs with NCQ function

STEP 1: Set Up UEFI.

A. Enter UEFI SETUP UTILITY Advanced screen Storage Conﬁ guration. B. Set the option “SATA Mode Selection” to [AHCI].

STEP 2: Install Windows system.

7 / 7 64-bit / VistaTM / VistaTM 64-bit OS on your

3. BIOS Information

The Flash Memory on the motherboard stores BIOS Setup Utility. When you start up the computer, please press <F2> or <Del> during the Power-On-Self-Test (POST) to enter BIOS Setup utility; otherwise, POST continues with its test routines. If you wish to enter BIOS Setup after POST, please restart the system by pressing <Ctl> + <Alt> + <Delete>, or pressing the reset button on the system chassis. The BIOS Setup program is designed to be user-friendly. It is a menu-driven program, which allows you to scroll through its various sub-menus and to select among the predetermined choices. For the detailed information about BIOS Setup, please refer to the User Manual (PDF ﬁ le) contained in the Support CD.

4. Software Support CD information

This motherboard supports various Microsoft 64-bit / VistaTM / Vista motherboard contains necessary drivers and useful utilities that will enhance motherboard features. To begin using the Support CD, insert the CD into your CD-ROM drive. It will display the Main Menu automatically if “AUTORUN” is enabled in your computer. If the Main Menu does not appear automatically, locate and double-click on the ﬁ le “ASSETUP.EXE” from the BIN folder in the Support CD to display the menus.

64-bit / XP / XP 64-bit. The Support CD that came with the

ASRock H61M-DG3/USB3 Motherboard

Windows

operating systems: 7 / 7

English

Page 24

1. Einführung

Wir danken Ihnen für den Kauf des ASRock H61M-DG3/USB3 Motherboard, ein zuverlässiges Produkt, welches unter den ständigen, strengen Qualitätskontrollen von ASRock gefertigt wurde. Es bietet Ihnen exzellente Leistung und robustes Design, gemäß der Verpﬂ ichtung von ASRock zu Qualität und Halbarkeit. Diese Sch- nellinstallationsanleitung führt in das Motherboard und die schrittweise Installation ein. Details über das Motherboard ﬁ nden Sie in der Bedienungsanleitung auf der Support-CD.

Da sich Motherboard-Speziﬁ kationen und BIOS-Software verändern können, kann der Inhalt dieses Handbuches ebenfalls jederzeit geändert werden. Für den Fall, dass sich Änderungen an diesem Handbuch ergeben, wird eine neue Version auf der ASRock-Website, ohne weitere Ankündigung, verfügbar sein. Die neuesten Graﬁ kkarten und unterstützten CPUs sind auch auf der ASRock-Website aufgelistet. ASRock-Website: http://www.asrock.com Wenn Sie technische Unterstützung zu Ihrem Motherboard oder speziﬁ sche Informationen zu Ihrem Modell benötigen, besuchen Sie bitte unsere Webseite: www.asrock.com/support/index.asp

1.1 Kartoninhalt

ASRock H61M-DG3/USB3 Motherboard (Micro ATX-Formfaktor: 22.6 cm x 17.3 cm; 8.9 Zoll x 6.8 Zoll) ASRock H61M-DG3/USB3 Schnellinstallationsanleitung ASRock H61M-DG3/USB3 Support-CD Zwei Serial ATA (SATA) -Datenkabel (optional) Ein I/O Shield

Deutsch

ASRock erinnert...

Zur besseren Leistung unter Windows® 7 / 7, 64 Bit / Vista 64 Bit empfehlen wir, die Speicherkonﬁ guration im BIOS auf den AHCI- Modus einzustellen. Hinweise zu den BIOS-Einstellungen ﬁ nden Sie in der Bedienungsanleitung auf der mitgelieferten CD.

/ VistaTM

ASRock H61M-DG3/USB3 Motherboard

Page 25

1.2 Speziﬁ kationen

Plattform - Micro ATX-Formfaktor: 22.6 cm x 17.3 cm; 8.9 Zoll x 6.8 Zoll

- Alle Feste Kondensatordesign CPU - Unterstützt Intel LGA1155-Paket

- Unterstützt Intel

- Unterstützt freigegebene CPU der K-Serie Chipsatz - Intel® H61

- Unterstützt Intel® Rapid Start Technology und Smart Connect Technology Speicher - Unterstützung von Dual-Kanal-Speichertechnologie

- 2 x Steckplätze für DDR3

- Unterstützt DDR3 1600/1333/1066 non-ECC, ungepufferter Speicher (DDR3 1600 mit Intel DDR3 1333 mit Intel® Sandy Bridge-Prozessor)

- Max. Kapazität des Systemspeichers: 16GB

- Unterstützt Intel Intel® Ivy Bridge-Prozessor Erweiterungs- - 1 x PCI Express 3.0 x16-Steckplatz steckplätze * PCIE 3.0 wird nur mit Intel® Ivy Bridge-Prozessor unterstützt. Mit Intel® Sandy Bridge-Prozessor wird nur PCIE 2.0 unterstützt.

- 1 x PCI Express 2.0 x1-Steckplätze Onboard-VGA * Integrierte Intel Ausgänge können nur durch GPU-integrierte Prozessoren unterstützt werden.

- Unterstützt hochauﬂ ösende integrierte Intel Intel® Quick-Sync-Video 2.0, Intel® InTruTM 3D, Intel® Clear Video-Technik (HD), Intel® InsiderTM, Intel® HD Graphics 2500/4000 mit Intel

- Unterstützt hochauﬂ ösende integrierte Intel®-Graﬁ klösungen: Intel® Quick-Sync-Video, Intel® InTruTM 3D, Intel® Clear Video-Technik (HD), Intel® HD Graphics 2000/3000, Intel® Advanced Vector Extensions (AVX) mit Intel® Sandy Bridge Prozessor

- Pixel Shader 5.0, DirectX 11 mit Intel Pixel Shader 4.1, DirectX 10.1 mit Intel Prozessor

- Maximal gemeinsam genutzter Speicher 1760MB mit Intel® Ivy Bridge-Prozessor. Maximal gemeinsam genutzter

CoreTM (2te Generation) i7 / i5 / i3 im

Turbo Boost 2.0-Technologie

Ivy Bridge-Prozessor,

Extreme Memory Proﬁ le (XMP)1.3/1.2 mit

HD-Graﬁ kdarstellungen und die VGA-

-Graﬁ klösungen:

Ivy Bridge-Prozessor

Ivy Bridge-Prozessor,

Sandy Bridge-

Deutsch

ASRock H61M-DG3/USB3 Motherboard

Page 26

Deutsch

Speicher 1759MB mit Intel® Sandy Bridge-Prozessor.

- Doppel-VGA Ausgabe: unterstützt DVI-D und D-Sub Ports durch unabhängige Bildschirmanzeige Kontrolleure

- Unterstützt DVI mit einer maximalen Auﬂ ösung von 1920 x 1200 bei 60 Hz

- Unterstützt D-Sub mit einer maximalen Auﬂ ösung von 2048 x 1536 bei 75 Hz

- Unterstützt HDCP-Funktion mit DVI-Port

- Unterstutzt 1080p Blu-ray (BD) / HD-DVD-Wiedergabe mit DVI-Port

Audio - 5.1 CH HD Audio (Realtek ALC662 Audio Codec) LAN - PCIE x1 Gigabit LAN 10/100/1000 Mb/s

- Realtek RTL8111E

- Unterstützt Wake-On-LAN

- Unterstützt LAN-Kabelerkennung

- Unterstützt energieefﬁ zientes Ethernet 802.3az

- Unterstützt PXE E/A-Anschlüsse I/O Panel an der - 1 x PS/2-Mausanschluss Rückseite - 1 x PS/2-Tastaturanschluss

- 1 x D-Sub port

- 1 x DVI-D port

- 4 x Standard-USB 2.0-Anschlüsse

- 2 x Standard-USB 3.0-Anschlüsse

- 1 x RJ-45 LAN Port mit LED (ACT/LINK LED und SPEED LED)

- HD Audiobuchse: Audioeingang / Lautsprecher vorne / Mikrofon USB3.0 - 2 x USB 3.0-Ports an der Rückseite durch Etron EJ188H, unterstützt USB 1.1/2.0/3.0 mit bis zu 5 Gb/s

- 1 x USB 3.0-Header (unterstützt zwei USB 3.0-Ports) an der Vorderseite durch Etron EJ188H unterstützt USB

1.1/2.0/3.0 mit bis zu 5 Gb/s Anschlüsse - 4 x SATA2 3,0 GB/s-Anschlüsse, unterstützen NCQ-, AHCI- und „Hot Plug“ (Hot-Plugging)- Funktionen

- 1 x Druckerport-Anschlussleiste

- 1 x COM-Anschluss-Header

- 1 x Verteiler für Gehäuseeindringversuche

- 1 x CPUlüfter-Anschluss (4-pin)

- 1 x Gehäuselüfter-Anschluss (4-pin)

- 1 x Stromlüfter-Anschluss (3-pin)

ASRock H61M-DG3/USB3 Motherboard

Page 27

- 24-pin ATX-Netz-Header

- 4-pin anschluss für 12V-ATX-Netzteil

- Anschluss für Audio auf der Gehäusevorderseite

- 2 x USB 2.0-Anschlüsse (Unterstützung 4 zusätzlicher USB 2.0-Anschlüsse)

- 1 x USB 3.0-Anschlüsse (Unterstützung 2 zusätzlicher USB 3.0-Anschlüsse) BIOS - 32Mb AMI BIOS

- AMIs Legal BIOS UEFI mit GUI-Unterstützung

- Unterstützung für “Plug and Play”

- ACPI 1.1-Weckfunktionen

- JumperFree-Übertaktungstechnologie

- SMBIOS 2.3.1

- IGPU, DRAM, PCH, CPU PLL, VTT, VCCSA Stromspannung Multianpassung CD d’assistance - Treiber, Dienstprogramme, Antivirussoftware (Probeversion), CyberLink MediaEspresso 6.5-Testversion, ASRock MAGIX-Multimedia-Suite - OEM Hardware Monitor - Überwachung der CPU-Temperatur

- Motherboardtemperaturerkennung

- Drehzahlmessung für CPU/Gehäuse/Stromlüfter

- Geräuscharmer CPU-/Gehäuselüfter (ermöglicht die au tomatische Anpassung der Gehäuselüftergeschwindigkeit durch CPU- Temperatur)

- Mehrstuﬁ ge Geschwindigkeitsteuerung für CPU-/ Gehäuselüfter

- GEHÄUSE OFFEN-Erkennung

- Spannungsüberwachung: +12V, +5V, +3.3V, Vcore

Betriebssysteme - Unterstützt Microsoft Vista

64-Bit / XP / XP 64-Bit

Windows® 7 / 7 64-Bit / VistaTM /

Zertiﬁ zierungen - FCC, CE, WHQL

- Gemäß Ökodesign-Richtlinie (ErP/EuP) (Stromversorgung gemäß Ökodesign-Richtlinie (ErP/EuP) erforderlich)

* Für die ausführliche Produktinformation, besuchen Sie bitte unsere Website: http://www.asrock.com

ASRock H61M-DG3/USB3 Motherboard

Deutsch

Page 28

1.3 Einstellung der Jumper

Die Abbildung verdeutlicht, wie Jumper gesetzt werden. Werden Pins durch Jumperkappen verdeckt, ist der Jumper “Gebrückt”. Werden keine Pins durch Jumperkappen verdeckt, ist der Jumper “Offen”. Die Abbildung zeigt einen 3-Pin Jumper dessen Pin1 und Pin2 “Gebrückt” sind, bzw. es beﬁ ndet sich eine Jumper-Kappe auf diesen beiden Pins.

Jumper Einstellun Beschreibung

CMOS löschen

(CLRCMOS1, 3-Pin jumper)

(siehe S.2, No. 21)

Hinweis:

CLRCMOS1 ermöglicht Ihnen die Löschung der Daten im CMOS. Zum Löschen und Zurücksetzen der Systemparameter auf die Standardeinrichtung schalten Sie den Computer bitte aus und trennen das Netzkabel von der Stromversorgung. Warten Sie 15 Sekunden, schließen Sie dann Pin2 und Pin3 am CLRCMOS1 über einen Jumper fünf Sekunden lang kurz. Sie sollten das CMOS allerdings nicht direkt nach der BIOS-Aktualisierung löschen. Wenn Sie das CMOS nach Abschluss der BIOS-Aktualisierung löschen müssen, fahren Sie zuerst das System hoch. Fahren Sie es dann vor der CMOS-Löschung herunter. Bitte beachten Sie, dass Kennwort, Datum, Uhrzeit, benutzerdeﬁ niertes Proﬁ l, 1394 GUID und MAC-Adresse nur gelöscht werden, wenn die CMOS-Batterie entfernt wird.

DefaultEinstellung

CMOS löschen

Deutsch

ASRock H61M-DG3/USB3 Motherboard

Page 29

1.4 Integrierte Header und Anschlüsse

Seriell-ATAII-Anschlüsse Diese vier Serial ATAII-

(SATA2_0: siehe S.2 - No. 10)

(SATA2_1: siehe S.2 - No. 8)

(SATA2_2: siehe S.2 - No. 12)

(SATA2_3: siehe S.2 - No. 11)

aktuelle SATAII-Schnittstelle ermöglicht eine Datenübertragungsrate bis 3,0 Gb/s.

Serial ATA- (SATA-) SJedes Ende des SATA Datenkabel Datenkabels kann an die SATA

(Option)

oder das SATAII Verbindungsstück auf dieser Hauptplatine angeschlossen werden.

Integrierte Header und Anschlüsse sind KEINE Jumper. Setzen Sie KEINE Jumperkappen auf diese Header und Anschlüsse. Wenn Sie Jumperkappen auf Header und Anschlüsse setzen, wird das Motherboard unreparierbar beschädigt!

(SATAII-) Verbínder

SATA2_3

unterstützten SATA-Datenkabel

SATA2_1

für interne Massenspeichergeräte. Die

SATA2_2

SATA2_0

/ SATAII Festplatte

USB 2.0-Header Zusätzlich zu den vier

(9-pol. USB6_7)

(siehe S.2 - No. 15)

üblichen USB 2.0-Ports an den

I/O-Anschlüssen beﬁ nden sich zwei USB 2.0- Anschlussleisten am Motherboard. Pro USB 2.0-

USB_PWR

P-9

P-8

USB_PWR

P+9

P+8

GND

DUMMY

(9-pol. USB8_9)

(siehe S.2 - No. 16)

Anschlussleiste werden zwei

USB 2.0-Ports unterstützt.

ASRock H61M-DG3/USB3 Motherboard

Deutsch

Page 30

USB 3.0-Header Neben zwei Standard-USB

(19-pol. USB3_2_3)

(siehe S.2 - No. 24)

Header an diesem Motherboard. Dieser USB 3.0 Header kann zwei USB 3.0 Ports unterstützen.

3.0-Ports am E/A-Panel

beﬁ ndet sich ein USB 3.0-

Vbus

IntA_P0_SSRX-

IntA_P0_SSRX+

GND

IntA_P0_SSTX-

IntA_P0_SSTX+

GND

IntA_P0_D-

IntA_P0_D+

VbusVbus

IntA_P1_SSRX-

IntA_P1_SSRX+

GND

IntA_P1_SSTX-

IntA_P1_SSTX+

GND

IntA_P1_D-

IntA_P1_D+

DUMMY

Deutsch

Druckerport-Anschlussleiste Dies ist eine Schnittstelle zum

(25-pol. LPT1)

Anschluss eines Druckerport-

(siehe S.2 - No. 18)

Drucker auf einfache Weise anschließen können.

Anschluss für Audio auf Dieses Interface zu einem der Gehäusevorderseite Audio-Panel auf der Vorder

(9-Pin HD_AUDIO1)

(siehe S.2 - No. 19)

Anschlussmöglichkeit und Kontrolle über Audio-Geräte.

1. High Deﬁ nition Audio unterstützt Jack Sensing (automatische Erkennung falsch angeschlossener Geräte), wobei jedoch die Bildschirmverdrahtung am Gehäuse HDA unterstützen muss, um richtig zu funktionieren. Beachten Sie bei der Installation im System die Anweisungen in unserem Handbuch und im Gehäusehandbuch.

2. Wenn Sie die AC’97-Audioleiste verwenden, installieren Sie diese wie nachstehend beschrieben an der Front-Audioanschlussleiste: A. Schließen Sie Mic_IN (MIC) an MIC2_L an. B. Schließen Sie Audio_R (RIN) an OUT2_R und Audio_L (LIN) an OUT2_L an. C. Schließen Sie Ground (GND) an Ground (GND) an.

D. MIC_RET und OUT_RET sind nur für den HD-Audioanschluss gedacht. Diese

Anschlüsse müssen nicht an die AC’97-Audioleiste angeschlossen werden. E. So aktivieren Sie das Mikrofon an der Vorderseite. Bei den Betriebssystemen Windows

Wählen Sie „Mixer“. Wählen Sie „Recorder“ (Rekorder). Klicken Sie dann auf „FrontMic“ (Vorderes Mikrofon). Bei den Betriebssystemen Windows Wählen Sie im Realtek-Bedienfeld die „FrontMic“ (Vorderes Mikrofon)- Registerkarte. Passen Sie die „Recording Volume“ (Aufnahmelautstärke) an.

AFD#

ERROR#

PINIT#

Kabels, mit dem Sie passende

SLIN#

SPD2

SPD1

SPD0

STB#

seite Ihres Gehäuses,

ermöglicht Ihnen eine bequeme

SPD3

SPD4

SPD5

GND

PRESENCE#

MIC2_R

MIC2_L

GND

SPD6

MIC_RET

OUT2_R

SPD7

ACK#

J_SENSE

BUSY

SLCT

OUT_RET

OUT2_L

XP / XP 64 Bit:

7 / 7 64 Bit / VistaTM / VistaTM 64 Bit:

ASRock H61M-DG3/USB3 Motherboard

Page 31

System Panel-Header Dieser Header unterstützt

(9-pin PANEL1)

(siehe S.2 - No. 14)

Schließen Sie die Ein-/Austaste, die Reset-Taste und die Systemstatusanzeige am Gehäuse an diesen Header an; befolgen Sie dabei die nachstehenden Hinweise zur Pinbelegung. Beachten Sie die positiven und negativen Pins, bevor Sie die Kabel anschließen.

PWRBTN (Ein-/Ausschalter):

RESET (Reset-Taste):

PLED (Systembetriebs-LED):

HDLED (Festplattenaktivitäts-LED):

mehrere Funktion der

Systemvorderseite.

Zum Anschließen des Ein-/Ausschalters an der Frontblende des Gehäu ses. Sie können konﬁ gurieren, wie das System mit Hilfe des Ein-/Ausschalters ausgeschaltet werden können soll.

Zum Anschließen der Reset-Taste an der Frontblende des Gehäuses. Mit der Reset-Taste können Sie den Computer im Falle eines Absturzes neu starten.

Zum Anschließen der Betriebsstatusanzeige an der Frontblende des Gehäuses. Die LED leuchtet, wenn das System in Betrieb ist. Die LED blinkt, wenn sich das System im Ruhezustand S1 beﬁ ndet. Die LED schaltet sich aus, wenn sich das System in den Modi S3/S4 beﬁ ndet oder ausgeschaltet ist (S5).

Zum Anschließen der Festplattenaktivitäts-LED an der Frontblende des Gehäuses. Die LED leuchtet, wenn die Festplatte Daten liest oder schreibt.

Das Design der Frontblende kann je nach Gehäuse variiere. Ein Frontblendenmodul besteht hauptsächlich aus einer Ein-/Austaste, einer Reset-Taste, einer Betriebs-LED, einer Festplattenaktivitäts-LED, Lautsprechern, etc. Stellen Sie beim Anschließen des Frontblendenmoduls Ihres Gehäuses an diesem Header sicher, dass die Kabel- und Pinbelegung korrekt übereinstimmen.

Gehäuselautsprecher-Header Schließen Sie den

(4-pin SPEAKER1)

(siehe S.2 - No. 13)

Gehäuselautsprecher an

diesen Header an.

ASRock H61M-DG3/USB3 Motherboard

Deutsch

Page 32

Gehäuse- und Stromlüfteranschlüsse

(4-pin CHA_FAN1)

(siehe S.2 - No. 9)

(3-pin PWR_FAN1)

(siehe S.2 - No. 25)

Verbinden Sie die Lüfterkabel mit den Lüfteranschlüssen, wobei der schwarze Draht an den Schutzleiterstift angeschlossen wird.

Deutsch

CPU-Lüfteranschluss Verbinden Sie das CPU -

(4-pin CPU_FAN1)

(siehe S.2 - No. 3)

Lüfterkabel mit diesem

Anschluss und passen Sie den

schwarzen Draht dem

4 3 2 1

+12V

CPU_FAN_SPEED

FAN_SPEED_CONTROL

GND

Erdungsstift an.

Obwohl dieses Motherboard einen vierpoligen CPU-Lüfteranschluss (Quiet Fan) bietet, können auch CPU-Lüfter mit dreipoligem Anschluss angeschlossen werden; auch ohne Geschwindigkeitsregulierung. Wenn Sie einen dreipoligen CPU-Lüfter an den CPU-Lüferanschluss dieses Motherboards anschließen möchten, verbinden Sie ihn bitte mit den Pins 1 – 3.

Lüfter mit dreipoligem Anschluss installieren

ATX-Netz-Header Verbinden Sie die ATX-

(24-pin ATXPWR1)

(siehe S.2 - No. 4)

Stromversorgung mit diesem

Header.

12 124

Obwohl dieses Motherboard einen 24-pol. ATX Stromanschluss bietet, kann es auch mit einem modiﬁ zierten traditionellen 20-pol. ATX-Netzteil verwendet werden. Um ein 20-pol. ATX-Netzteil zu verwenden, stecken Sie den Stecker mit Pin 1 und Pin 13 ein.

Pins 1–3 anschließen

Installation eines 20-pol. ATX-Netzteils

ATX 12V Anschluss Bitte schließen Sie an diesen

(4-pin ATX12V1)

(siehe S.2 - No. 1)

Anschluss die ATX 12V

Stromversorgung an.

ASRock H61M-DG3/USB3 Motherboard

Page 33

COM-Anschluss-Header Dieser COM-Anschluss-

(9-pin COM1)

(siehe S.2 - No. 17)

Header wird verwendet, um

ein COM-Anschlussmodul zu

unterstützen.

Verteiler für Gehäuseeindringversuche Dieses Motherboard unterstützt

(2-pin CI1)

die GEHÄUSE OFFEN-

(siehe S.2 - No. 22)

Erkennungsfunktion,die

feststellt, ob dieGehäuseab-

Signal

GND

deckung entferntwurde. Für diese Funktion istein Ge häuse erforderlich, dasmit ei nem Design zur Erkennung von Gehäuseeindringver suchenausgestattet ist.

ASRock H61M-DG3/USB3 Motherboard

Deutsch

Page 34

2. BIOS-Information

Das Flash Memory dieses Motherboards speichert das Setup-Utility. Drücken Sie <F2> oder <Del> während des POST (Power-On-Self-Test) um ins Setup zu gelangen, ansonsten werden die Testroutinen weiter abgearbeitet. Wenn Sie ins Setup gelangen wollen, nachdem der POST durchgeführt wurde, müssen Sie das System über die Tastenkombination <Ctrl> + <Alt> + <Delete> oder den Reset-Knopf auf der Gehäusevorderseite, neu starten. Natürlich können Sie einen Neustart auch durchführen, indem Sie das System kurz ab- und danach wieder anschalten. Das Setup-Programm ist für eine bequeme Bedienung entwickelt worden. Es ist ein menügesteuertes Programm, in dem Sie durch unterschiedliche Untermenüs scrollen und die vorab festgelegten Optionen auswählen können. Für detaillierte Informationen zum BIOS-Setup, siehe bitte das Benutzerhandbuch (PDF Datei) auf der Support CD.

3. Software Support CD information

Dieses Motherboard unterstützt eine Reiche von Microsoft® Windows® Betriebssystemen: 7 / 7 64-Bit / Vista beigefügte Support-CD enthält hilfreiche Software, Treiber und Hilfsprogramme, mit denen Sie die Funktionen Ihres Motherboards verbessern können Legen Sie die Support-CD zunächst in Ihr CD-ROM-Laufwerk ein. Der Willkommensbildschirm mit den Installationsmenüs der CD wird automatisch aufgerufen, wenn Sie die “Autorun”-Funktion Ihres Systems aktiviert haben. Erscheint der Wilkommensbildschirm nicht, so “doppelklicken” Sie bitte auf das File ASSETUP.EXE im BIN-Verzeichnis der Support-CD, um die Menüs aufzurufen. Das Setup-Programm soll es Ihnen so leicht wie möglich machen. Es ist menügesteuert, d.h. Sie können in den verschiedenen Untermenüs Ihre Auswahl treffen und die Programme werden dann automatisch installiert.

/ Vista

64-Bit / XP / XP 64-Bit. Die Ihrem Motherboard

Deutsch

ASRock H61M-DG3/USB3 Motherboard

Page 35

1. Introduction

Merci pour votre achat d’une carte mère ASRock H61M-DG3/USB3, une carte mère très ﬁ able produite selon les critères de qualité rigoureux de ASRock. Elle offre des performances excellentes et une conception robuste conformément à l’engagement d’ASRock sur la qualité et la ﬁ abilité au long terme. Ce Guide d’installation rapide présente la carte mère et constitue un guide d’installation pas à pas. Des informations plus détaillées concernant la carte mère pourront être trouvées dans le manuel l’utilisateur qui se trouve sur le CD d’assistance.

Les spéciﬁ cations de la carte mère et le BIOS ayant pu être mis à jour, le contenu de ce manuel est sujet à des changements sans notiﬁ cation. Au cas où n’importe qu’elle modiﬁ cation intervenait sur ce manuel, la version mise à jour serait disponible sur le site web ASRock sans nouvel avis. Vous trouverez les listes de prise en charge des cartes VGA et CPU également sur le site Web ASRock. Site web ASRock, http://www.asrock.com Si vous avez besoin de support technique en relation avec cette carte mère, veuillez consulter notre site Web pour de plus amples informations particulières au modèle que vous utilisez. www.asrock.com/support/index.asp

1.1 Contenu du paquet

Carte mère ASRock H61M-DG3/USB3 (Facteur de forme Micro ATX: 8.9 pouces x 6.8 pouces, 22.6 cm x 17.3 cm) Guide d’installation rapide ASRock H61M-DG3/USB3 CD de soutien ASRock H61M-DG3/USB3 Deux câbles de données de série ATA (SATA) (en option) Un I/O Panel Shield

ASRock vous rappelle...

Pour bénéﬁ cier des meilleures performances sous Windows® 7 / 7 64 bits

/ Vista

/ VistaTM 64 bits, il est recommandé de paramétrer l'option BIOS dans Conﬁ guration de stockage en mode AHCI. Pour plus de détails sur l'installation BIOS, référez-vous au "Mode d'emploi" sur votre CD de support.

ASRock H61M-DG3/USB3 Motherboard

Français

Page 36

Français

1.2 Spéciﬁ cations

Format - Facteur de forme Micro ATX:

8.9 pouces x 6.8 pouces, 22.6 cm x 17.3 cm

- Conception à condensateur robuste CPU - Prend en charge les processeurs Intel deuxième génération dans l’ensemble LGA1155

- Prend en charge la technologie Intel® Turbo Boost 2.0

- Prise en charge des unités centrales non verrouillées de série K Chipsets - Intel

H61

- Prend en charge les technologies Intel® Rapid Start et Smart Connect Mémoire - Compatible avec la Technologie de Mémoire à Canal Double

- 2 x slots DIMM DDR3

- Supporter DDR3 1600/1333/1066 non-ECC, sans amortissement mémoire (DDR3 1600 avec CPU Intel Bridge, DDR3 1333 avec CPU Intel® Sandy Bridge)

- Capacité maxi de mémoire système: 16GB

- Prend en charge le proﬁ l de mémoire extrême Intel® (XMP)

1.3/1.2 avec processeur Intel® Ivy Bridge CPU Slot d’extension - 1 x slot PCI Express 3.0 x16 * PCIE 3.0 n’est pris en charge qu’avec le processeur Intel Ivy Bridge. Avec le processeur Intel® Sandy Bridge, seul PCIE 2.0 est pris en charge.

- 1 x slot PCI Express 2.0 x1 VGA sur carte * Intel

HD Graphics avec visuels intégrés (Built-in Visuals) et les sorties VGA sont uniquement pris en charge par les processeurs à GPU intégré.

- Supporte Intel

HD Graphics Built-in Visuals: Intel® Quick Sync Video 2.0, Intel® InTruTM 3D, Intel® Clear Video HD Technology, Intel® InsiderTM, Intel® HD Graphics 2500/4000 avec processeur Intel® Ivy Bridge CPU

- Supporte Intel® HD Graphics Built-in Visuals: Intel® Quick Sync Video, Intel

InTruTM 3D, Intel® Clear Video HD Technology, Intel® HD Graphics 2000/3000, Intel® Advanced Vector Extensions (AVX) avec processeur Intel Bridge CPU

- Pixel Shader 5.0, DirectX 11 avec CPU Intel® Ivy Bridge, Pixel Shader 4.1, DirectX 10.1 avec CPU Intel® Sandy

CoreTM i7 / i5 / i3 de

Ivy

Sandy

ASRock H61M-DG3/USB3 Motherboard

Page 37

Bridge

- Mémoire partagée max 1760MB avec processeur Intel® Ivy Bridge CPU. Mémoire partagée max 1759MB avec processeur Intel® Sandy Bridge CPU.

- Output de VGA Duel: supporter DVI-D et D-Sub ports par les controleurs de display independents

- Prend en charge le DVI avec une résolution maximale jusqu’à 1920x1200 @ 60Hz

- Prend en charge le D-Sub avec une résolution maximale jusqu’à 2048x1536 @ 75Hz

- Prise en charge de la fonction HDCP avec ports DVI

- Supporter 1080p Blu-ray(BD)/ lecteur de HD-DVD avec ports DVI Audio - 5.1 Son haute déﬁ nition de CH (codec audio Realtek ALC662) LAN - PCIE x1 Gigabit LAN 10/100/1000 Mb/s

- Realtek RTL8111E

- Support du Wake-On-LAN

- Prise en charge de la détection de câble LAN

- Prend en charge la norme Energy Efﬁ cient Ethernet

(Ethernet à efﬁ cacité énergétique) 802.3az

- Supporte PXE

Panneau arrière I/O Panel

- 1 x port souris PS/2

- 1 x port clavier PS/2

- 1 x port D-Sub

- 1 x port DVI-D

- 4 x ports USB 2.0 par défaut

- 2 x ports USB 3.0 par défaut

- 1 x port LAN RJ-45 avec LED (ACT/LED CLIGNOTANTE et LED VITESSE)

- Prise HD Audio: Entrée Ligne / Haut-parleur frontal / Microphone USB 3.0 - 2 x ports USB3.0 à l’arrière par Etron EJ188H, prennent en charge USB 1.1/2.0/3.0 jusqu’à 5 Gb/s

- 1 x barrette USB3.0 en façade (prend en charge 2 ports USB 3.0) par Etron EJ188H, prend en charge USB

1.1/2.0/3.0 jusqu’à 5 Gb/s Connecteurs - 4 x connecteurs SATA2, prennent en charge un taux de transfert de données pouvant aller jusqu’à 3.0Go/s, supporte NCQ, AHCI et « Hot Plug » (Branche ment à chaud)

ASRock H61M-DG3/USB3 Motherboard

Français

Page 38

Français

- 1 x embase de port d’impression

- 1 x En-tête de port COM

- 1 x Embase d’intrusion châssis

- 1 x Connecteur pour ventilateur de CPU (br. 4)

- 1 x Connecteur pour ventilateur de Châssis (br. 4)

- 1 x Connecteur pour ventilateur de pouvoir (br. 3)

- br. 24 connecteur d’alimentation ATX

- br. 4 connecteur d’alimentation 12V ATX

- Connecteur audio panneau avant

- 2 x En-tête USB 2.0 (prendre en charge 4 ports USB 2.0 supplémentaires)

- 1 x En-tête USB 3.0 (prendre en charge 2 ports USB 3.0 supplémentaires) BIOS - 32Mb BIOS AMI

- AMI UEFI Legal BIOS avec support GUI

- Support du “Plug and Play”

- Compatible pour événements de réveil ACPI 1.1

- Gestion jumperless

- Support SMBIOS 2.3.1

- IGPU, DRAM, PCH, CPU PLL, VTT, VCCSA Tension Multi-ajustement CD d’assistance - Pilotes, utilitaires, logiciel anti-virus (version d’évaluation), CyberLink MediaEspresso 6.5 Trial, Suite multimédia ASRock MAGIX - OEM Surveillance - Contrôle de la température CPU système - Mesure de température de la carte mère

- Tachéomètre ventilateur processeur/châssis/ventilateur

- Ventilateur silencieux pour unité centrale/châssis (permet le

réglage automatique de la vitesse du ventilateur pour châssis, selon la température de l’unité centrale)

- Commande de ventilateur CPU/châssis à plusieurs vitesses

- Détection d’OUVERTURE DE BOÎTIER

- Monitoring de la tension: +12V, +5V, +3.3V, Vcore OS - Microsoft

Windows® 7 / 7 64-bit / VistaTM / Vista

64-bit

/ XP / XP 64-bit Certiﬁ cations - FCC, CE, WHQL

- Prêt pour ErP/EuP (alimentation Prêt pour ErP/EuP requise)

* Pour de plus amples informations sur les produits, s’il vous plaît visitez notre site web: http://www.asrock.com

ASRock H61M-DG3/USB3 Motherboard

Page 39

1.3 Réglage des cavaliers

L’illustration explique le réglage des cavaliers. Quand un capuchon est placé sur les broches, le cavalier est « FERME ». Si aucun capuchon ne relie les broches,le cavalier est « OUVERT ». L’illustration montre un cavalier à 3 broches dont les broches 1 et 2 sont « FERMEES » quand le capuchon est placé sur ces 2 broches.

Le cavalier Description

Effacer la CMOS

(CLRCMOS1) (voir p.2 ﬁ g. 21)

Remarque :

Paramètres par défaut

CLRCMOS1 vous permet d’effacer les données du CMOS. Pour effacer et réinitialiser les paramètres du système à la conﬁ guration originale, veuillez éteindre l’ordinateur et débrancher le cordon d’alimentation de la prise de courant. Après 15 secondes, utilisez un couvercle de jumper pour court-circuiter les broches pin2 et pin3 de CLRCMOS1 pendant secondes. Veuillez cependant ne pas effacer le CMOS immédiatement a

près avoir mis à jour le BIOS. Si vous avez besoin d’effacer le CMOS après avoir mis à jour le BIOS, vous devez allumer en premier le système, puis l’éteindre avant de continuer avec l’opération d’effacement du CMOS. Veuillez noter que le mot de passe, la date, l’heure, le proﬁ l par défaut de l’utilisateur, 1394 GUID et l’adresse MAC seront effacés seulement si la batterie du CMOS est enlevée.

Effacer la CMOS

ASRock H61M-DG3/USB3 Motherboard

Français

Page 40

1.4 En-têtes et Connecteurs sur Carte

Connecteurs Série ATAII Ces quatre connecteurs Série

(SATA2_0: voir p.2 No. 10)

(SATA2_1: voir p.2 No. 8)

(SATA2_2: voir p.2 No. 12)

(SATA2_3: voir p.2 No. 11)

actuelle permet des taux transferts de données pouvant

aller jusqu’à 3,0 Gb/s.

Câble de données Toute cote du cable de data Série ATA (SATA) SATA peut etre connecte au

(en option)

ou au connecteur SATAII sur la carte mere.

Les en-têtes et connecteurs sur carte NE SONT PAS des cavaliers. NE PAS placer les capuchons de cavalier sur ces en-têtes et connecteurs. Le fait de placer les capuchons de cavalier sur les en-têtes et connecteurs causera à la carte mère des dommages irréversibles!

ATAII (SATAII) prennent en

SATA2_3

SATA2_1

charge les câbles SATA pour

les périphériques de stockage

SATA2_2

internes. L’interface SATAII

SATA2_0

disque dur SATA / SATAII /

Français

USB_PWR

P-9

P-8

USB_PWR

USB_PW R

P-11

P-10

USB_PW R

P+9

P+8

P+11

P+10

GND

DUMMY

En-tête USB 2.0 A côté des quatre ports

(USB6_7 br.9)

(voir p.2 No. 15)

USB 2.0 par défaut sur le

panneau E/S, il y a deux embases USB 2.0 sur cette carte mère. Chaque embase USB 2.0 peut prendre en

(USB8_9 br.9)

(voir p.2 No. 16)

charge 2 ports USB 2.0.

ASRock H61M-DG3/USB3 Motherboard

Page 41

En-tête USB 3.0 En plus des deux ports USB

(USB3_2_3 br. 19)

(voir p.2 No. 24)

sur la carte mère. Cette barrette USB 3.0 peut prendre en charge deux ports USB 3.0.

3.0 par défaut sur le panneau

E/S, il y a une barrette USB 3.0

Vbus

IntA_P0_SSRX-

IntA_P0_SSRX+

GND

IntA_P0_SSTX-

IntA_P0_SSTX+

GND

IntA_P0_D-

IntA_P0_D+

VbusVbus

IntA_P1_SSRX-

IntA_P1_SSRX+

GND

IntA_P1_SSTX-

IntA_P1_SSTX+

GND

IntA_P1_D-

IntA_P1_D+

DUMMY

Embase de port d’impression AIl s’agit d’une interface pour le

(LPT1 25 broches)

(voir p.2 No. 18)

permet le raccordement pratique de périphériques d’impression.

Connecteur audio panneau C’est une interface pour

(HD_AUDIO1 br. 9)

(voir p.2 No. 19)

qui permet le branchement et le contrôle commodes de périphériques audio.

1. L’audio à haute déﬁ nition (HDA) prend en charge la détection de ﬁ che, mais le ﬁ l de panneau sur le châssis doit prendre en charge le HDA pour fonctionner correctement. Veuillez suivre les instructions dans notre manuel et le manuel de châssis aﬁ n installer votre système.

2. Si vous utilisez le panneau audio AC’97, installez-le sur l’adaptateur audio du panneau avant conformément à la procédure ci-dessous : A. Connectez Mic_IN (MIC) à MIC2_L. B. Connectez Audio_R (RIN) à OUT2_R et Audio_L (LIN) à OUT2_L. C. Connectez Ground (GND) à Ground (GND). D. MIC_RET et OUT_RET sont réservés au panneau audio HD. Vous n’avez pas besoin de les connecter pour le panneau audio AC’97. E. Pour activer le micro avant. Pour les systèmes d’exploitation Windows Sélectionnez “Mixer”. Sélectionnez “Recorder” (Enregistreur). Puis cliquez sur “FrontMic” (Micro avant). Pour les systèmes d’exploitation Windows VistaTM 64 bits : Allez sur l’onglet “FrontMic” (Micro avant) sur le Panneau de contrôle Realtek. Ajustez “Recording Volume” (Volume d’enregistrement).

AFD#

câble du port d’impression, qui

un câble avant audio en façade

STB#

ERROR#

PINIT#

SPD1

SPD0

SLIN#

SPD2

SPD3

SPD4

SPD5

GND

MIC2_L

GND

SPD7

SPD6

ACK#

PRESENCE#

MIC_RET

OUT2_R

MIC2_R

BUSY

OUT_RET

OUT2_L

J_SENSE

SLCT

XP / XP 64 bits :

7 / 7 64 bits / VistaTM /

Français

ASRock H61M-DG3/USB3 Motherboard

Page 42

En-tête du panneau système Cet en-tête permet d’utiliser

(PANEL1 br.9)

(voir p.2 No. 14)

Connectez l’interrupteur d’alimentation, l’interrupteur de réinitialisation et l’indicateur d’état du système du châssis sur cette barrette en respectant l’affectation des broches décrite ci-dessous. Faites attention aux broches positives et négatives avant de connecter les câbles.

PWRBTN (Interrupteur d’alimentation):

RESET (Interrupteur de réinitialisation):

PLED (DEL alimentation système):

HDLED (DEL activité du disque dur):

plusieurs fonctions du

panneau système frontal.

Connectez ici le connecteur d’alimentation sur le panneau avant du châssis. Vous pouvez conﬁ gurer la façon de mettre votre système hors tension avec l’interrupteur d’alimentation.

Connectez ici le connecteur de réinitialisation sur le panneau avant du châssis. Appuyez sur l’interrupteur de réinitialisation pour redémarrer l’ordinateur s’il se bloque ou s’il n’arrive pas à redémarrer normalement.

Connectez ici l’indicateur d’état de l’alimentation sur le panneau avant du châssis. Ce voyant DEL est allumé lorsque le système est en marche. Le voyant DEL clignote lorsque le système est en mode veille S1. Le voyant DEL est éteint lorsque le système est en mode veille S3/ S4 ou lorsqu’il est éteint (S5).

Connectez ici le voyant DEL d’activité du disque dur sur le panneau avant du châssis. Ce voyant DEL est allumé lorsque le disque dur est en train de lire ou d’écrire des données.

Français

Le design du panneau avant peut varier en fonction du châssis. Un module de panneau avant consiste principalement en : interrupteur d’alimentation, interrupteur de réinitialisation, voyant DEL d’alimentation, voyant DEL d’activité du disque dur, haut-parleur, etc. Lorsque vous connectez le panneau avant de votre châssis sur cette barrette, vériﬁ ez bien à faire correspondre les ﬁ ls et les broches.

En-tête du haut-parleur Veuillez connecter le de châssis haut-parleur de châssis sur

(SPEAKER1 br. 4)

(voir p.2 No. 13)

cet en-tête.

ASRock H61M-DG3/USB3 Motherboard

Page 43

Connecteur pour châssis et ventilateur

(CHA_FAN1 br. 4)

(voir p.2 No. 9)

(PWR_FAN1 br. 3)

(voir p.2 No. 25)

Branchez les câbles du ventilateur aux connecteurs pour ventilateur et faites correspondre le ﬁ l noir à la broche de terre.

Connecteur du ventilateur Veuillez connecter le câble de de l’UC ventilateur d’UC sur ce

(CPU_FAN1 br. 4)

(voir p.2 No. 3)

connecteur et brancher le ﬁ l

noir sur la broche de terre.

4 3 2 1

+12V

FAN_SPEED_CONTROL

CPU_FAN_SPEED

GND

Bien que cette carte mère offre un support de (Ventilateur silencieux ventilateur de CPU à 4 broches , le ventilateur de CPU à 3 broches peut bien fonctionner même sans la fonction de commande de vitesse du ventilateur. Si vous prévoyez de connecter le ventilateur de CPU à 3 broches au connecteur du ventilateur de CPU sur cette carte mère, veuillez le connecter aux broches 1-3.

Installation de ventilateur à 3 broches

Broches 1-3 connectées

En-tête d’alimentation ATX Veuillez connecter l’unité

(ATXPWR1 br. 24)

(voir p.2 No. 4)

Bien que cette carte mère fournisse un connecteur de courant ATX 24 broches, elle peut encore fonctionner

d’alimentation ATX sur cet en-

tête.

12 124

si vous adopter une alimentation traditionnelle ATX 20 broches. Pour utiliser une alimentation ATX 20 broches, branchez à l’alimentation électrique ainsi qu’aux broches 1 et 13.

20-Installation de l’alimentation électrique ATX

Connecteur ATX 12V Veuillez connecter une unité

(ATX12V1 br.4)

(voir p.2 No. 1)

d’alimentation électrique ATX 12V sur ce connecteur.

ASRock H61M-DG3/USB3 Motherboard

Français

Page 44

En-tête de port COM Cette en-tête de port COM est

(COM1 br.9)

(voir p.2 No. 17)

utilisée pour prendre en charge

un module de port COM.

Embase d’intrusion châssis Cette carte-mère prend

(CI1 br.2)

en charge la détection

(voir p.2 No. 22)

d’OUVERTURE DE BOÎTIER,

Signal

GND

quidétecte tout retrait du capot duchâssis. Cette fonction nécessite un châssis qui a été conçu pour la détectiond’intrusion dans le châssis.

Français

ASRock H61M-DG3/USB3 Motherboard

Page 45

2. Informations sur le BIOS

La puce Flash Memory sur la carte mère stocke le Setup du BIOS. Lorsque vous démarrez l’ordinateur, veuillez presser <F2> ou <Del> pendant le POST (Power-OnSelf-Test) pour entrer dans le BIOS; sinon, le POST continue ses tests de routine. Si vous désirez entrer dans le BIOS après le POST, veuillez redémarrer le système en pressant <Ctl> + <Alt> + <Suppr>, ou en pressant le bouton de reset sur le boîtier du système. Vous pouvez également redémarrer en éteignant le système et en le rallumant. L’utilitaire d’installation du BIOS est conçu pour être convivial. C’est un programme piloté par menu, qui vous permet de faire déﬁ ler par ses divers sous- menus et de choisir parmi les choix prédéterminés. Pour des informations détaillées sur le BIOS, veuillez consulter le Guide de l’utilisateur (ﬁ chier PDF) dans le CD technique.

3. Informations sur le CD de support

Cette carte mère supporte divers systèmes d’exploitation Microsoft® Windows®: 7 / 7 64 bits / VistaTM / Vista cette carte mère contient les pilotes et les utilitaires nécessaires pour améliorer les fonctions de la carte mère. Pour utiliser le CD technique, insérez-le dans le lecteur de CD-ROM. Le Menu principal s’afﬁ che automatiquement si “AUTORUN” est activé dans votre ordinateur. Si le Menu principal n’apparaît pas automatiquement, localisez dans le CD technique le ﬁ chier “ASSETUP.EXE” dans le dossier BIN et double- cliquez dessus pour afﬁ cher les menus.

64 bits / XP / XP 64 bits. Le CD technique livré avec

ASRock H61M-DG3/USB3 Motherboard

Français

Page 46

1. Introduzione

Grazie per aver scelto una scheda madre ASRock H61M-DG3/USB3, una scheda madre afﬁ dabile prodotta secondo i severi criteri di qualità ASRock. Le prestazioni eccellenti e il design robusto si conformano all’impegno di ASRock nella ricerca della qualità e della resistenza. Questa Guida Rapida all’Installazione contiene l’introduzione alla motherboard e la guida passo-passo all’installazione. Informazioni più dettagliate sulla motherboard si possono trovare nel manuale per l’utente presente nel CD di supporto.

Le speciﬁ che della scheda madre e il software del BIOS possono essere aggiornati, pertanto il contenuto di questo manuale può subire variazioni senza preavviso. Nel caso in cui questo manuale sia modiﬁ cato, la versione aggiornata sarà disponibile sul sito di ASRock senza altro avviso. Sul sito ASRock si possono anche trovare le più recenti schede VGA e gli elenchi di CPU supportate. ASRock website http://www.asrock.com Se si necessita dell’assistenza tecnica per questa scheda madre, visitare il nostro sito per informazioni speciﬁ che sul modello che si sta usando. www.asrock.com/support/index.asp

1.1 Contenuto della confezione

Scheda madre ASRock H61M-DG3/USB3 (Micro ATX Form Factor: 8.9-in x 6.8-in, 22.6 cm x 17.3 cm) Guida di installazione rapida ASRock H61M-DG3/USB3 CD di supporto ASRock H61M-DG3/USB3 Due cavi dati Serial ATA (SATA) (opzionali) Un I/O Shield

Italiano

ASRock vi ricorda...

Per ottenere migliori prestazioni in Windows® 7 / 7 64-bit / Vista 64-bit, si consiglia di impostare l'opzione BIOS in Storage Conﬁ guration (Conﬁ gurazione di archiviazione) sulla modalità AHCI. Per l'impostazione BIOS, fare riferimento a “User Manual” (Manuale dell'utente) nel CD di supporto per dettagli.

/ VistaTM

ASRock H61M-DG3/USB3 Motherboard

Page 47

1.2 Speciﬁ che

Piattaforma - Micro ATX Form Factor: 8.9-in x 6.8-in, 22.6 cm x 17.3 cm

- Design condensatore robusto Processore - Supporta Intel pacchetto in LGA1155

- Supporto della tecnologia Intel

- Supporta CPU unlocked serie K Chipset - Intel® H61

- Supporta tecnologia Intel® Rapid Start Technology e Smart Connect Technology Memoria - Supporto tecnologia Dual Channel Memory

- 2 x slot DDR3 DIMM

- Supporto DDR3 1600/1333/1066 non-ECC, momoria senza buffer (DDR3 1600 con CPU Intel CPU Intel® Sandy Bridge)

- Capacità massima della memoria di sistema: 16GB

- Supporto di Intel CPU Intel® Ivy Bridge Slot di - 1 x Alloggi PCI Express 3.0 x16 espansione * PCIE 3.0 è supportato soltanto con la CPU Intel® Ivy Bridge. Con la CPU Intel® Sandy Bridge, supporta solamente PCIE

2.0.

- 1 x Alloggi PCI Express 2.0 x1 VGA su scheda * Le uscite Intel essere supportate solo con processori dotati di GPU integrata.

- Supporta Intel Video 2.0, Intel® InTruTM 3D, Intel® Clear Video HD Technology, Intel® InsiderTM, Intel® HD Graphics 2500/4000 con CPU Intel® Ivy Bridge

- Supporta Intel Video, Intel® InTruTM 3D, Intel® Clear Video HD Technology, Intel® HD Graphics 2000/3000, Intel® Advanced Vector Extensions (AVX) con CPU Intel® Sandy Bridge

- Pixel Shader 5.0, DirectX 11 con CPU Intel Shader 4.1, DirectX 10.1 con CPU Intel® Sandy Bridge

- Memoria massima condivisa 1760MB con CPU Intel® Ivy Bridge. Memoria massima condivisa 1759MB con CPU Intel

Sandy Bridge.

- Uscita VGA Doppia: supporto porte DVI-D e D-Sub tramite

CoreTM i7 / i5 / i3 di seconda generazione in

Turbo Boost 2.0

Ivy Bridge, DDR3 1333 con

XMP (Extreme Memory Proﬁ le)1.3/1.2 con

HD Graphics Built-in Visuals e VGA possono

HD Graphics Built-in Visuals: Intel® Quick Sync

Ivy Bridge, Pixel

Italiano

ASRock H61M-DG3/USB3 Motherboard

Page 48

Italiano

veriﬁ catore display indipendente

- Supporta DVI con risoluzione massima ﬁ no a 1920x1200 @ 60Hz

- Supporta D-Sub con risoluzione massima ﬁ no a 2048x1536 @ 75Hz

- Supporto della funzione HDCP con le porte DVI

- Supporto 1080p Blu-ray (BD) / HD-DVD riproduzione con le porte DVI Audio - 5.1 Audio HD CH (Realtek ALC662 Audio Codec) LAN - PCIE x1 Gigabit LAN 10/100/1000 Mb/s

- Realtek RTL8111E

- Supporta Wake-On-LAN

- Supporta il rilevamento cavo LAN

- Supporto di Energy Efﬁ cient Ethernet 802.3az

- Supporta PXE Pannello I/O Panel posteriore I/O - 1 x porta PS/2 per mouse

- 1 x porta PS/2 per tastiera

- 1 x Porta D-Sub

- 1 x Porta DVI-D

- 4 x porte USB 2.0 già integrate

- 2 x porte USB 3.0 già integrate

- 1 x porte LAN RJ-45 con LED (LED azione/collegamento e LED velocità)

- Connettore HD Audio: ingresso linea / cassa frontale / microfono USB 3.0 - 2 x porte USB 3.0 posteriori amministrate dal controller Etron EJ188H, supporto di USB 1.1/2.0/3.0 ﬁ no a 5Gb/s

- 1 x header USB 3.0 frontale (supporta 2 porte USB 3.0) amministrato dal controller Etron EJ188H, supporto di USB 1.1/2.0/3.0 ﬁ no a 5Gb/s Connettori - 4 x connettori SATA2 3.0Go/s, sopporta delle funzioni NCQ, AHCI e “Hot Plug”

- 1 x Collettore porta stampante

- 1 x collettore porta COM

- 1 x header di intrusione dello chassis

- 1 x Connettore CPU ventola (4-pin)

- 1 x Connettore Chassis ventola (4-pin)

- 1 x Connettore Alimentazione ventola (3-pin)

- 24-pin collettore alimentazione ATX

- 4-pin connettore ATX 12V

ASRock H61M-DG3/USB3 Motherboard

Page 49

- Connettore audio sul pannello frontale

- 2 x Collettore USB 2.0 (supporta 4 porte USB 2.0)

- 1 x Collettore USB 3.0 (supporta 2 porte USB 3.0)

BIOS - 32Mb AMI BIOS

- AMI UEFI Legal BIOS con interfaccia di supporto

- Supporta “Plug and Play”

- Compatibile con ACPI 1.1 wake up events

- Supporta jumperfree

- Supporta SMBIOS 2.3.1

- Regolazione multi-voltaggio IGPU, DRAM, PCH, CPU PLL, VTT, VCCSA

CD di - Driver, Utilità, Software AntiVirus (versione di prova), supporto CyberLink MediaEspresso 6.5 Trial, Suite multimediale

ASRock MAGIX - OEM Monitoraggio - Sensore per la temperatura del processore Hardware - Sensore temperatura scheda madre

- Indicatore di velocità per la ventola del CPU/Chassis/ Alimentazione

- Ventola CPU/Chassis silenziosa (permette la regolazione automatica della ventola dello chassis in base alla temperatura della CPU madre)

- Ventola CPU/Chassis con controllo di varie velocità

- Rilevamento CASE APERTO

- Voltaggio: +12V, +5V, +3.3V, Vcore Compatibi- - Microsoft

Windows® 7 / 7 64 bit / VistaTM / Vista

64 bit / XP /

lità SO XP 64 bit Certiﬁ cazioni - FCC, CE, WHQL

- Predisposto ErP/EuP (è necessaria l’alimentazione predisposta per il sistema ErP/EuP)

* Per ulteriori informazioni, prego visitare il nostro sito internet: http://www.asrock.com

ASRock H61M-DG3/USB3 Motherboard

Italiano

Page 50

1.3 Setup dei Jumpers

L’illustrazione mostra come sono settati i jumper. Quando il ponticello è posizionato sui pin, il jumper è “CORTOCIRCUITATO”. Se sui pin non ci sono ponticelli, il jumper è “APERTO”. L’illustrazione mostra un jumper a 3 pin in cui il pin1 e il pin2 sono “CORTOCIRCUITATI” quando il ponticello è posizionato su questi pin.

Jumper Settaggio del Jumper

Resettare la CMOS

(CLRCMOS1) (vedi p.2 item 21)

Nota:

CLRCMOS1 permette si azzerare i dati nella CMOS. Per cancellare e ripristinare i

parametri del sistema sulla conﬁ gurazione iniziale, spegnere il computer e

Impostazione

predeﬁ nita

scollegare il cavo d’alimentazione dalla presa di corrente. Attendere 15 secondi, poi usare un cappuccio jumper per cortocircuitare il pin 2 ed il pin 3 su CLRCMOS1 per 5 secondi. Tuttavia, si consiglia di non cancellare la CMOS subito dopo avere aggiornato il BIOS. Se si deve azzerare la CMOS quando si è completato l’aggiornamento del BIOS, è necessario per prima cosa avviare il sistema e poi spegnerlo prima di eseguire l’azzeramento della CMOS. Notare che password, data, ore, proﬁ lo utente predeﬁ nito, 1394 GUID e indirizzo MAC saranno cancellati solo se è rimossa la batteria della CMOS.

Azzeramen-

to CMOS

Italiano

ASRock H61M-DG3/USB3 Motherboard

Page 51

1.4 Collettori e Connettori su Scheda

Connettori Serial ATAII Questi quattro connettori Serial

(SATA2_0: vedi p.2 Nr. 10)

(SATA2_1: vedi p.2 Nr. 8)

(SATA2_2: vedi p.2 Nr. 12)

(SATA2_3: vedi p.2 Nr. 11)

SATA per dispositivi di memoria interni. L’interfaccia SATAII attuale permette velocità di trasferimento dati ﬁ no a

3.0 Gb/s.

Cavi dati Serial ATA (SATA) Una o altra estremità del cavo

(Opzionale)

collegata al disco rigido SATA / SATAII o al connettore di SATAII su questa cartolina base.

I collettori ed i connettori su scheda NON sono dei jumper. NON installare cappucci per jumper su questi collettori e connettori. L’installazione di cappucci per jumper su questi collettori e connettori provocherà danni permanenti alla scheda madre!

ATAII (SATAII) supportano cavi

SATA2_3

SATA2_1

dati SATA per dispositivi di

immagazzinamento interni.

ATAII (SATAII) supportano cavi

SATA2_2

SATA2_0

di dati SATA può essere

Collettore USB 2.0 Oltre alle quattro porte USB 2.0

(9-pin USB6_7)

(vedi p.2 Nr. 15)

predeﬁ nite nel pannello I/O, la

scheda madre dispone di due intestazioni USB 2.0. Ciascuna intestazione USB 2.0 supporta due porte USB 2.0.

USB_PWR

P-9

P-8

USB_PWR

P+9

P+8

GND

DUMMY

(9-pin USB8_9) (vedi p.2 Nr. 16)

ASRock H61M-DG3/USB3 Motherboard

Italiano

Page 52

Collettore USB 3.0 Oltre alle due porte USB 3.0

(19-pin USB3_2_3)

(vedi p.2 Nr. 24)

di un header USB 3.0 che supporta due porte USB 3.0.

standard del pannello I/O,

questa scheda madre è dotata

Vbus

IntA_P0_SSRX-

IntA_P0_SSRX+

GND

IntA_P0_SSTX-

IntA_P0_SSTX+

GND

IntA_P0_D-

IntA_P0_D+

VbusVbus

IntA_P1_SSRX-

IntA_P1_SSRX+

GND

IntA_P1_SSTX-

IntA_P1_SSTX+

GND

IntA_P1_D-

IntA_P1_D+

DUMMY

Italiano

Collettore porta stampante Questa è un’interfaccia per il

(LPT1 25 pin)

(vedi p.2 No. 18)

cavo porta stampante che

consente di collegare, con

comodità, dispositivi di stampa.

Connettore audio sul È un’interfaccia per il cavo del pannello frontale pannello audio. Che consente

(9-pin HD_AUDIO1)

(vedi p.2 Nr. 19)

1. La caratteristica HDA (High Deﬁ nition Audio) supporta il rilevamento dei connettori, però il pannello dei cavi sul telaio deve supportare la funzione HDA (High Deﬁ nition Audio) per far sì che questa operi in modo corretto. Attenersi alle istruzioni del nostro manuale e del manuale del telaio per installare il sistema.

2. Se si utilizza un pannello audio AC’97, installarlo nell’intestazione audio del pannello anteriore, come indicato di seguito:

A. Collegare Mic_IN (MIC) a MIC2_L. B. Collegare Audio_R (RIN) a OUT2_R e Audio_L (LIN) ad OUT2_L. C. Collegare Ground (GND) a Ground (GND).

E. Per attivare il microfono frontale. Sistema operativo Windows Selezionare “Mixer”. Selezionare “Recorder” (Registratore). Poi, fare clic su “FrontMic” (Microfono frontale). Sistema operativo Windows® 7 / 7 64-bit / VistaTM / VistaTM 64-bit: Andare alla scheda “FrontMic” (Microfono frontale) del pannello di controllo Realtek. Regolare la voce “Recording Volume” (Volume registrazione).

dei dispositivi audio.

D. MIC_RET e OUT_RET sono solo per il pannello audio HD. Non è necessario collegarli per il pannello audio AC’97.

AFD#

ERROR#

PINIT#

SLIN#

SPD2

SPD1

SPD0

STB#

connessione facile e controllo

SPD3

SPD5

SPD4

GND

PRESENCE#

MIC2_R

MIC2_L

GND

SPD7

SPD6

MIC_RET

J_SENSE

OUT2_R

ACK#

BUSY

OUT_RET

OUT2_L

SLCT

XP / XP 64-bit:

ASRock H61M-DG3/USB3 Motherboard

Page 53

Collettore pannello di sistema Questo collettore accomoda

(9-pin PANEL1)

(vedi p.2 Nr. 14)

Collegare l’interruttore d’alimentazione, l’interruttore di ripristino, l’indicatore di stato del sistema del pannello frontale del telaio a questo header in base all’assegnazione dei pin deﬁ nita di seguito. Determinare i pin positivi e negativi prima di collegare i cavi.

PWRBTN (interruttore d’alimentazione):

RESET (interruttore di ripristino):

PLED (LED alimentazione del sistema):

HDLED (LED attività disco rigido):

diverse funzioni di sistema

pannello frontale.

Va collegato all’interruttore d’alimentazione del pannello frontale del telaio. Usando l’interruttore d’alimentazione si può conﬁ gurare il modo in cui si spegne il sistema.

Va collegato all’interruttore di ripristino del pannello frontale del telaio. Premere l’interruttore di ripristino per riavviare il sistema se il computer si blocca e non riesce ad eseguire un normale riavvio.

Va collegato all’indicatore di stato d’alimentazione del pannello fronta le del telaio. Il LED è acceso quando il sistema è operativo. Il LED conti nua a lampeggiare quando il sistema è in stato di standby S1. Il LED è spento quando il sistema è in stato di sospensione /ibernazione S3/S4 oppure spento (S5).

Va collegato al LED attività disco rigido del pannello frontale del telaio. Il LED è acceso quando disco rigido legge e scrive i dati.

Il design del pannello frontale può variare in base ai telai. Il modulo di un pannello frontale può consistere di: interruttore d’alimentazione, interruttore di ripristino, LED d’alimentazione, LED attività disco rigido, casse, eccetera. Quando si collega il modulo del pannello frontale a questo header, assicurarsi che l’assegnazione dei ﬁ li e dei pin sia fatta corrispondere in modo appropriato.

Collettore casse telaio Collegare le casse del telaio a

(4-pin SPEAKER1)

(vedi p.2 Nr. 13)

questo collettore.

ASRock H61M-DG3/USB3 Motherboard

Italiano

Page 54

Collettori Chassis ed alimentazione ventola Collegare i cavi della ventola ai

(4-pin CHA_FAN1)

(vedi p.2 Nr. 9)

corrispondenti connettori

facendo combaciare il cavo

nero col pin di terra.

(3-pin PWR_FAN1)

(vedi p.2 Nr. 25)

Connettore ventolina CPU Collegare il cavo della ventolina

(4-pin CPU_FAN1)

(vedi p.2 Nr. 3)

CPU a questo connettore e far

combaciare il ﬁ lo nero al pin

terra.

4 3 2 1

+12V

FAN_SPEED_CONTROL

CPU_FAN_SPEED

GND

Sebbene la presente scheda madre disponga di un supporto per ventola CPU a 4 piedini (ventola silenziosa), la ventola CPU a 3 piedini è in grado di funzionare anche senza la funzione di controllo della velocità della ventola. Se si intende collegare la ventola CPU a 3 piedini al connettore della ventola CPU su questa scheda madre, collegarla ai piedini 1-3.

Piedini 1-3 collegati

Installazione della ventola a 3 piedini

Connettore alimentazione ATX Collegare la sorgente

(24-pin ATXPWR1)

(vedi p.2 Nr. 4)

Con questa scheda madre, c’è in dotazione un

d’alimentazione ATX a questo

connettore.

12 124

connettore elettrico ATX a 24 pin, ma può funzionare lo stesso se si adotta un alimentatore ATX a 20 pin. Per usare l’alimentatore ATX a 20 pin, collegare l’alimentatore con il Pin 1 e il Pin 13.

Installazione dell’alimentatore ATX a 20 pin

Italiano

Connettore ATX 12 V Collegare un alimentatore ATX

(4-pin ATX12V1)

(vedi p.2 Nr. 1)

12 V a questo connettore.

ASRock H61M-DG3/USB3 Motherboard

Page 55

Collettore porta COM Questo collettore porta COM è

(9-pin COM1)

(vedi p.2 Nr. 17)

utilizzato per supportare il

modulo porta COM.

Header di intrusione dello chassis Questa scheda madre supporta

(2-pin CI1)

la funzione di rilevamento del

(vedi p.2 Nr. 22)

CASE APERTOche rileva che

Signal

GND

il coperchio dellochassis è stato rimosso.Questa funzione richiede unochassis con struttura dirilevamento di intrusione dellochassis.

ASRock H61M-DG3/USB3 Motherboard

Italiano

Page 56

2. Informazioni sul BIOS

La Flash Memory sulla scheda madre contiene le Setup Utility. Quando si avvia il computer, premi <F2> o <Del> durante il Power-On-Self-Test (POST) della Setup utility del BIOS; altrimenti, POST continua con i suoi test di routine. Per entrare il BIOS Setup dopo il POST, riavvia il sistema premendo <Ctl> + <Alt> + <Delete>, o premi il tasto di reset sullo chassis del sistema. Per informazioni più dettagliate circa il Setup del BIOS, fare riferimento al Manuale dell’Utente (PDF ﬁ le) contenuto nel cd di supporto.

3. Software di supporto e informazioni su

Questa scheda madre supporta vari sistemi operativi Microsoft® Windows®: 7 / 7 64-bit / Vista scheda madre contiene i driver e utilità necessari a potenziare le caratteristiche della scheda. Inserire il CD di supporto nel lettore CD-ROM. Se la funzione “AUTORUN” è attivata nel computer, apparirà automaticamente il Menù principale. Se il Menù principale non appare automaticamente, posizionarsi sul ﬁ le “ASSETUP.EXE” nel CESTINO del CD di supporto e cliccare due volte per visualizzare i menù.

/ Vista

64-bit / XP / XP 64-bit. Il CD di supporto a corredo della

Italiano

ASRock H61M-DG3/USB3 Motherboard

Page 57

1. Introducción

Gracias por su compra de ASRock H61M-DG3/USB3 placa madre, una placa de conﬁ anza producida bajo el control de calidad estricto y persistente. La placa madre provee realización excelente con un diseño robusto conforme al compromiso de calidad y resistencia de ASRock. Esta Guía rápida de instalación contiene una introducción a la placa base y una guía de instalación paso a paso. Puede encontrar una información más detallada sobre la placa base en el manual de usuario incluido en el CD de soporte.

Porque las especiﬁ caciones de la placa madre y el software de BIOS podrían ser actualizados, el contenido de este manual puede ser cambiado sin aviso. En caso de cualquier modiﬁ cación de este manual, la versión actualizada estará disponible en el website de ASRock sin previo aviso. También encontrará las listas de las últimas tarjetas VGA y CPU soportadas en la página web de ASRock. Website de ASRock http://www.asrock.com Si necesita asistencia técnica en relación con esta placa base, visite nuestra página web con el número de modelo especíﬁ co de su placa. www.asrock.com/support/index.asp

1.1 Contenido de la caja

Placa base ASRock H61M-DG3/USB3 (Factor forma Micro ATX: 22,6 cm x 17,3 cm, 8,9” x 6,8”) Guía de instalación rápida de ASRock H61M-DG3/USB3 CD de soporte de ASRock H61M-DG3/USB3 Dos cables de datos Serial ATA (SATA) (Opcional) Una protección I/O

ASRock le recuerda...

Para mejorar el rendimiento en Windows® 7 / 7 64 bits / Vista 64 bits, es recomendable establecer la opción del BIOS de la conﬁ gura- ción de almacenamiento en el modo AHCI. Para obtener detalles sobre la conﬁ guración del BIOS, consulte el “Manual del usuario” que se en- cuentra en nuestro CD de soporte.

/ VistaTM

ASRock H61M-DG3/USB3 Motherboard

Español

Page 58

Español

1.2 Especiﬁ cación

Plataforma - Factor forma Micro ATX: 22,6 cm x 17,3 cm, 8,9” x 6,8”

- Todo diseño de Capacitor Sólido Procesador - Admite los procesadores Intel generación en el paquete LGA1155

- Admite la tecnología Intel

- Admite procesador desbloqueado de la serie K Chipset - Intel® H61

- Admite las tecnologías Intel® Rapid Start y Smart Connect Memoria - Soporte de Tecnología de Memoria de Doble Canal

- 2 x DDR3 DIMM slots

- Apoya DDR3 1600/1333/1066 non-ECC, memoria de un-buffered (DDR3 1600 con CPU Intel DDR3 1333 con CPU Intel® Sandy Bridge)

- Máxima capacidad de la memoria del sistema: 16GB

- Compatible con Intel® Extreme Memory Proﬁ le (XMP)1.3/1.2 con la CPU Intel® Ivy Bridge Ranuras de - 1 x ranura PCI Express 3.0 x16 Expansión * PCIE 3.0 solamente se admite con una CPU Intel Bridge. Con una CPU Intel® Sandy Bridge, solamente admite PCIE 2.0.

- 1 x ranura PCI Express 2.0 x1 VGA OnBoard * Los efectos visuales incorporados con gráﬁ cos de alta deﬁ nición Intel

y las salidas VGA sólo se soportan con

procesadores con GPU integrada.

- Admite Intel

HD Graphics Built-in Visuals: Intel® Quick Sync Video 2.0, Intel® InTruTM 3D, Intel® Clear Video HD Technology, Intel® InsiderTM, Intel® HD Graphics 2500/4000 con la CPU Intel® Ivy Bridge

- Admite Intel® HD Graphics Built-in Visuals: Intel® Quick Sync Video, Intel

InTruTM 3D, Intel® Clear Video HD Technology, Intel® HD Graphics 2000/3000 e Intel® Advanced Vector Extensions (AVX) con la CPU Intel® Sandy Bridge

- Pixel Shader 5.0, DirectX 11 con CPU Intel® Ivy Bridge, Pixel Shader 4.1, DirectX 10.1 con CPU Intel

- 1760MB de Memoria máxima compartida con la CPU Intel® Ivy Bridge. 1759MB de Memoria máxima compartida con la CPU Intel

Sandy Bridge.

- Salida de VGA dual: apoya los puertos de DVI-D y de D-Sub por los reguladores independientes de la exhibición

CoreTM i7 / i5 / i3 de segunda

Turbo Boost 2.0 Technology

Ivy Bridge,

Sandy Bridge

Ivy

ASRock H61M-DG3/USB3 Motherboard

Page 59

- Admite DVI con una resolución máxima de 1920x1200 a 60 Hz

- Admite D-Sub con una resolución máxima de 2048x1536 a 75 Hz

- Admite la función HDCP con puertos DVI

- Apoya la reproducción de Blu-rayo de 1080p (BD) / HD-DVD con puertos DVI Audio - Sonido HD de 5.1 Canales (Códec de sonido Realtek ALC662) LAN - PCIE x1 Gigabit LAN 10/100/1000 Mb/s

- Realtek RTL8111E

- Soporta Wake-On-LAN

- Admite detección de conexión de cable LAN

- Compatible con Ethernet 802.3az de bajo consumo energético

- Compatible con PXE Entrada/Salida I/O Panel de Panel - 1 x puerto de ratón PS/2 Trasero - 1 x puerto de teclado PS/2

- 1 x puerto D-Sub

- 1 x puerto DVI-D

- 4 x puertos USB 2.0 predeterminados

- 2 x puertos USB 3.0 predeterminados

- 1 x Puerto LAN RJ-45 con LED (LED de ACCIÓN/ENLACE y LED de VELOCIDAD)

- Conexión de audio: Entrada de línea / Altavoz frontal / Micrófono USB 3.0 - 2 x puertos USB 3.0 traseros de Etron EJ188H, compatible con USB 1.1/2.0/3.0 de hasta 5 GB/s

- 1 x cabecera USB 3.0 delantera (compatible con 2 puertos USB 3.0) de Etron EJ188H, compatible con USB 1.1/2.0/3.0 de hasta 5 GB/s Conectores - 4 x conexiones SATA2, admiten una velocidad de transferencia de datos de hasta 3,0Gb/s, soporta NCQ, AHCI y “Conexión en caliente”

- 1 x cabecera de puerto de impresora

- 1x En-tête de port COM

- 1 x Conector de detección de intrusión en el chasis

- 1 x Conector de ventilador de CPU (4-pin)

- 1 x Conector de ventilador de chasis (4-pin)

- 1 x Conector de ventilador de alimentacion (3-pin)

Español

ASRock H61M-DG3/USB3 Motherboard

Page 60

Español

- 24-pin cabezal de alimentación ATX

- 4-pin conector de ATX 12V power

- Conector de audio de panel frontal

- 2 x Cabezal USB 2.0 (admite 4 puertos USB 2.0 adicionales)

- 1 x Cabezal USB 3.0 (admite 2 puertos USB 3.0 adicionales) BIOS - 32Mb AMI BIOS

- BIOS legal UEFI AMI compatible con GUI

- Soporta “Plug and Play”

- ACPI 1.1 compliance wake up events

- Soporta “jumper free”

- Soporta SMBIOS 2.3.1

- Múltiple ajuste de IGPU, DRAM, PCH, CPU PLL, VTT, VCCSA Voltage CD de soport - Controladores, utilidades, software de antivirus (versión de prueba), Prueba de CyberLink MediaEspresso 6.5, Conjunto multimedia ASRock MAGIX - OEM Monitor - Sensibilidad a la temperatura del procesador Hardware - Sensibilidad a la temperatura de la placa madre

- Taquímetros de los ventiladores del procesador y del CPU / chasis / alimentación

- Ventilador silencioso del procesador y el chasis (ajuste automático de la velocidad del ventilador del chasis en función de la temperatura del procesador)

- Control de ajuste de la velocidad del ventilador de la CPU / chasis

- Control de APERTURA DE CARCASA

- Monitor de Voltaje: +12V, +5V, +3.3V, Vcore OS - En conformidad con Microsoft

Windows® 7 / 7 64 bits /

VistaTM / VistaTM 64 bits / XP / XP 64 bits Certiﬁ caciones - FCC, CE, WHQL

- Cumple con la directiva ErP/EuP (se requiere una fuente de alimentación que cumpla con la directiva ErP/EuP)

* Para más información sobre los productos, por favor visite nuestro sitio web: http://www.asrock.com

ASRock H61M-DG3/USB3 Motherboard

Page 61

1.3 Setup de Jumpers

La ilustración muestra como los jumpers son conﬁ gurados. Cuando haya un jumper- cap sobre los pins, se dice gue el jumper está “Short”. No habiendo jumper cap sobre los pins, el jumper está “Open”. La ilustración muesta un jumper de 3 pins cuyo pin 1 y pin 2 están “Short”.

Jumper Setting

Limpiar CMOS

(CLRCMOS1, jumper de 3 pins) (ver p.2, No. 21)

Nota:

Valor predeterminado

Restablecimiento de

la CMOS

CLRCMOS1 permite borrar los datos de la memoria CMOS. Para borrar los parámetros del sistema y restablecer la conﬁ guración predeterminada de los mismos, apague el equipo y desenchufe el cable de alimentación de la toma de corriente eléctrica. Deje que transcurran 15 segundos y, después, utilice un puente cortocircuitar los contactos 2 y 3 de CLRCMOS1 durante 5 segundos. No borre la memoria CMOS justamente después de actualizar el BIOS. Si necesita borrar la memoria CMOS justamente después de actualizar el BIOS, debe iniciar primero el sistema y, a continuación, cerrarlo antes de llevar a cabo el borrado de dicha memoria. Tenga en cuenta que la contraseña, la fecha, la hora, el perﬁ l predeterminado del usuario, el GUID 1394 y la dirección MAC solamente se borrará si la batería CMOS se quita.

para

ASRock H61M-DG3/USB3 Motherboard

Español

Page 62

Español

1.4 Cabezales y Conectores en Placas

Los conectores y cabezales en placa NO son puentes. NO coloque las cubiertas de los puentes sobre estos cabezales y conectores. El colocar cubiertas de puentes sobre los conectores y cabezales provocará un daño permanente en la placa base.

Conexiones de serie ATAII Estas cuatro conexiones de

(SATA2_0: vea p.2, N. 10)

(SATA2_1: vea p.2, N. 8)

(SATA2_2: vea p.2, N. 12)

(SATA2_3: vea p.2, N. 11)

permite una velocidad de transferencia de 3.0 Gb/s.

Cable de datos de Cualquier extremo del cable de serie ATA (SATA) los datos de SATA puede ser

(Opcional)

conectado con el disco duro de SATA / SATAII o el conectador de SATAII en esta placa base.

Cabezal USB 2.0 Además de cuatro puertos

(9-pin USB6_7)

(vea p.2, N. 15)

USB 2.0 predeterminados en el

panel de E/S, hay dos bases de conexiones USB 2.0 en esta placa base. Cada una de estas bases de conexiones

(9-pin USB8_9)

(vea p.2, N. 16)

admite dos puertos USB 2.0.

serie ATAII (SATAII) admiten

SATA2_3

SATA2_1

cables SATA para dispositivos

de almacenamiento internos.

La interfaz SATAII actual

SATA2_2

USB_PWR

P-9

P-8

USB_PWR

P+9

P+8

SATA2_0

GND

DUMMY

GND

ASRock H61M-DG3/USB3 Motherboard

Page 63

Cabezal USB 3.0 Además de dos puertos 3.0

(19-pin USB3_2_3)

(vea p.2, N. 24)

predeterminados situados en el

panel E/S, encontrará una cabecera USB 3.0 en esta placa base. Esta cabecera USB

3.0 admiten dos puertos USB

3.0.

Vbus

IntA_P0_SSRX-

IntA_P0_SSRX+

GND

IntA_P0_SSTX-

IntA_P0_SSTX+

GND

IntA_P0_D-

IntA_P0_D+

VbusVbus

IntA_P1_SSRX-

IntA_P1_SSRX+

GND

IntA_P1_SSTX-

IntA_P1_SSTX+

GND

IntA_P1_D-

IntA_P1_D+

DUMMY

Cabecera de puerto de impresora Esta es una interfaz de puerto

(LPT1 de 25 terminales)

(vea p.2, N. 18)

permite conectar cómodamente dispositivos de impresión.

AFD#

para cable de impresora que

ERROR#

PINIT#

SLIN#

SPD2

SPD1

SPD0

STB#

SPD3

SPD4

SPD5

SPD6

GND

SPD7

ACK#

BUSY

SLCT

GND

PRESENCE#

MIC2_R

MIC2_L

MIC_RET

J_SENSE

OUT2_R

OUT_RET

OUT2_L

Conector de audio de Este es una interface para panel frontal cable de audio de panel frontal

(9-pin HD_AUDIO1)

(vea p.2, N. 19)

que permite conexión y control

conveniente de apparatos de Audio.

1. El Audio de Alta Deﬁ nición soporta la detección de conector, pero el cable de panel en el chasis debe soportar HDA para operar correctamente. Por favor, siga las instrucciones en nuestro manual y en el manual de chasis para instalar su sistema.

2. Si utiliza el panel de sonido AC’97, instálelo en la cabecera de sonido del panel frontal de la siguiente manera: A. Conecte Mic_IN (MIC) a MIC2_L. B. Conecte Audio_R (RIN) a OUT2_R y Audio_L (LIN) en OUT2_L. C. Conecte Ground (GND) a Ground (GND).

D. MIC_RET y OUT_RET son sólo para el panel de sonido HD. No

necesitará conectarlos al panel de sonido AC’97. E. Activación del micrófono frontal. En sistemas operativos Windows

XP / XP 64-bit: Seleccione “Mixer” (Mezclador). Seleccione “Recorder” (Grabadora). A continuación, haga clic en “FrontMic” (Micrófono frontal). En sistemas operativos Windows® 7 / 7 64-bit / VistaTM / VistaTM 64-bit: Acceda a la ﬁ cha “FrontMic” (Micrófono frontal) del panel de control Realtek. Ajuste la posición del control deslizante “Recording Volume” (Volumen de grabación).

Español

ASRock H61M-DG3/USB3 Motherboard

Page 64

Cabezal de panel de sistema Este cabezar acomoda varias

(9-pin PANEL1)

(vea p.2, N. 14)

Conecte el interruptor de alimentación, el interruptor de restablecimiento y el indicador de estado del sistema situados en el chasis con esta cabecera en función de las siguientes asignaciones de contacto. Preste atención a los contactos positivos y negativos antes de conectar los cables.

PWRBTN (interruptor de alimentación):

RESTABLECER (interruptor de restablecimiento):

PLED (LED de alimentación del sistema):

HDLED (LED de actividad del disco duro):

dunciones de panel frontal de

sistema.

Conecte el interruptor de encendido situado en el panel frontal del chasis. Puede conﬁ gurar la forma de apagar su sistema mediante el interruptor de alimentación.

Conecte el interruptor de restablecimiento situado en el panel frontal del chasis. Pulse el interruptor de restablecimiento para restablecer el equipo si se bloquea y no se reinicia con normalidad.

Conecte el indicador de estado de alimentación situado en el panel frontal del chasis. El LED se enciende cuando el sistema esté en funcionamiento. El LED parpadea cuando el sistema se encuentre en estado de suspensión S1. El LED se apaga cuando el sistema se encuentre en estado de suspensión S3/S4 o se apaga (S5).

Conecte el LED de actividad de disco duro situado en el panel frontal del chasis. El LED se enciende cuando el disco duro esté leyendo o escribiendo datos.

Español

Es posible que el diseño del panel frontal varíe en función del chasis. Un módulo del panel frontal consiste principalmente de interruptor de alimentación, interruptor de restablecimiento, LED de alimentación, LED de actividad del disco duro, altavoz, etc. Al conectar el módulo del panel frontal del chasis a esta cabecera, asegúrese de que las asignaciones de cables y las asignaciones de contactos coincidan correctamente.

Cabezal del altavoz del chasis Conecte el altavoz del chasis a

(4-pin SPEAKER1)

(vea p.2, N. 13)

su cabezal.

ASRock H61M-DG3/USB3 Motherboard

Page 65

Conectores de ventilador de chasis y alimentación

(4-pin CHA_FAN1)

(vea p.2, N. 9)

(3-pin PWR_FAN1)

(vea p.2, N. 25)

Por favor, conecte los cables del ventilador a los conectores de ventilador, haciendo coincidir el cable negro con la patilla de masa.

Conector del ventilador Conecte el cable del ventilador

4 3 2 1

de la CPU de la CPU a este conector y

(4-pin CPU_FAN1)

(vea p.2, N. 3)

haga coincidir el cable negro

con el conector de tierra.

FAN_SPEED_CONTROL

Aunque esta placa base proporciona compatibilidad para un ventilador (silencioso) de procesador de 4 contactos, el ventilador de procesador de 3 contactos seguirá funcionando correctamente incluso sin la función de control de velocidad del ventilador. Si pretende enchufar el ventilador de procesador de 3 contactos en el conector del ventilador de procesador de esta placa base, conéctelo al contacto 1-3.

Cabezal de alimentación ATX Conecte la fuente de

(24-pin ATXPWR1)

(vea p.2, N. 4)

A pesar de que esta placa base incluye in conector de alimentación ATX de 24 pins, ésta puede funcionar incluso si utiliza una fuente de alimentación ATX de 20 pins tradicional. Para usar una fuente de alimentación ATX de 20 pins, por favor, conecte su fuente de alimentación usando los Pins 1 y 13.

alimentación ATX a su cabezal.

Instalación de una Fuente de Alimentación ATX de 20 Pins

GND

+12V

CPU_FAN_SPEED

Contacto 1-3 conectado

Instalación del ventilador de 3 contactos

12 124

ASRock H61M-DG3/USB3 Motherboard

Español

Page 66

Conector de ATX 12V power Tenga en cuenta que es

(4-pin ATX12V1)

(vea p.2, N. 1)

necesario conectar este

conector a una toma de corriente con el enchufe ATX 12V, de modo que proporcione suﬁ ciente electricidad. De lo contrario no se podrá encender.

Cabezal del puerto COM Este cabezal del puerto COM

(9-pin COM1)

(vea p.2, N. 17)

se utiliza para admitir un

módulo de puerto COM.

Conector de detección de intrusión en el chasis Esta placa base admite la

(2-pin CI1)

función de control de

(vea p.2, N. 22)

APERTURA DE CARCASA,

quepermite detectar si se

Signal

GND

haretirado la cubierta del chasis. Dicha función requiere unchasis con diseño especíﬁ copara la detección de intrusiónen el chasis.

Español

ASRock H61M-DG3/USB3 Motherboard

Page 67

2. BIOS Información

El Flash Memory de la placa madre deposita SETUP Utility. Durante el Power-Up (POST) apriete <F2> o <Del> para entrar en la BIOS. Sí usted no oprime ninguna tecla, el POST continúa con sus rutinas de prueba. Si usted desea entrar en la BIOS después del POST, por favor reinicie el sistema apretando <Ctl> + <Alt> + <Borrar>, o apretando el botón Reset en el panel del ordenador. Para información detallada sobre como conﬁ gurar la BIOS, por favor reﬁ érase al Manual del Usuario (archivo PDF) contenido en el CD.

3. Información de Software Support CD

Esta placa-base soporta diversos tipos de sistema operativo Windows®: 7 / 7 64 bits / Vista la placa-base trae todos los drivers y programas utilitarios para instalar y conﬁ gurar la placa-base. Para iniciar la instalación, ponga el CD en el lector de CD y se desplegará el Menú Principal automáticamente si «AUTORUN» está habilitado en su computadora. Si el Menú Principal no aparece automáticamente, localice y doble-pulse en el archivo “ASSETUP.EXE” para iniciar la instalación.

/ Vista

64 bits / XP / XP 64 bits. El CD de instalación que acompaña

ASRock H61M-DG3/USB3 Motherboard

Español

Page 68

1. Введение

Благодарим вас за покупку материнской платы ASRock H61M-DG3/USB3 надежной материнской платы, изготовленной в соответствии с постоянно предъявляемыми ASRock жесткими требованиями к качеству. Она обеспечивает превосходную производительность и отличается отличной конструкцией, которые отражают приверженность ASRock качеству и долговечности. Данное руководство по быстрой установке включает вводную информацию о материнской плате и пошаговые инструкции по ее установке. можно найти в руководстве пользователя на компакт-диске поддержки.

Спецификации материнской платы и программное обеспечение BIOS иногда изменяются, поэтому содержание этого руководства может обновляться без уведомления. В случае любых модификаций руководства его новая версия будет размещена на веб-сайте ASRock без специального уведомления. Кроме того, самые свежие списки поддерживаемых модулей памяти и процессоров можно найти на сайте ASRock. Адрес веб-сайта ASRock http://www.asrock.com При необходимости технической поддержки по вопросам данной материнской платы посетите наш веб-сайт для получения информации об используемой модели. www.asrock.com/support/index.asp

1.1 Комплектность

Материнская плата ASRock H61M-DG3/USB3 (форм-фактор Micro ATX: 8,9 x 6,8 дюйма / 22,6 x 17,3 см)

Руководство по быстрой установке ASRock H61M-DG3/USB3 Компакт-диск поддержки ASRock H61M-DG3/USB3

2 x кабель данных Serial ATA (SATA) (дополнительно) 1 x I/O Щит Группы ввода / вывода

Более подробные сведения о плате

Русский

ASRock напоминает...

Для обеспечения максимальной производительности ОС Windows 7 / 7 64-bit / Vista

параметра Storage Configuration (Конфигурация запоминающего устройства) режим AHCI. Подробные сведения о настройке BIOS см. в руководстве пользователя на прилагаемом компакт-диске.

/ VistaTM 64-bit рекомендуется в BIOS выбрать для

ASRock H61M-DG3/USB3 Motherboard

Page 69

1.2 Спецификации

Платформа - форм-фактор Micro ATX: 8,9 x 6,8 дюйма / 22,6 x 17,3 см

- Весь Твердый Конденсаторный проект Процессор - Поддержка процессоров Intel исполнении LGA1155

- Поддержка технологии Intel® Turbo Boost 2.0

- Поддержка разблокированного ЦП серии K Набор микросхем - Intel

H61

- Поддержка технологии Intel® Rapid Start Technology и Smart Connect Technology Память - Поддержка технологии Dual Channel DDR3 Memory Technology

- 2 x гнезда DDR3 DIMM

- Поддержите DDR3 1600/1333/1066 не- ECC, безбуферная память (DDR3 1600 с процессором Intel процессором Intel® Sandy Bridge)

- Максимальный объем системной памяти: 16 ГБ

- поддержка профиля Intel помощью процессора Intel® Ivy Bridge

Гнезда - 1 x PCI Express 3.0 x16 расширения * PCIE 3.0 поставляется только в комплекте с ЦП Intel

комплекте с ЦП Intel® Sandy Bridge поставляется только модель PCIE 2.0.

- 1 x PCI Express 2.0 x1 Графика * Встроенный видеоадаптер Intel® HD Graphics и выходы VGA поддерживаются только с процессорами, оснащенными интегрированным графическим процессором.

- Поддержка функций встроенных видеоадаптеров Intel Quick Sync Video 2.0, Intel® InTruTM 3D, технологии Intel® Clear Video HD, Intel® InsiderTM, Intel® HD Graphics 2500/4000 с помощью процессора Intel® Ivy Bridge

- Поддержка функций встроенных видеоадаптеров Intel Quick Sync Video, Intel® InTruTM 3D, технологии Intel® Clear Video HD, Intel® HD Graphics 2000/3000, Intel® Advanced Vector Extensions (AVX) с помощью процессора Intel® Sandy Bridge

- Pixel Shader 5.0, DirectX 11 с процессором Intel Shader 4.1, DirectX 10.1 с процессором Intel® Sandy Bridge

- Макс. объем разделяемой памяти 1760Мб с помощью процессора Intel® Ivy Bridge. Макс. объем разделяемой памяти 1759Мб с помощью процессора Intel® Sandy Bridge.

- Двойственное VGA выходное устройство: поддерживает DVI-D и D-Sub порты через независимый контроллер дисплея

- Поддержка DVI с максимальным разрешением до 1920х1200 @ 60 Гц

- Поддержка D-Sub с максимальным разрешением до 2048х1536 @ 75 Гц

- Поддержка функции HDCP через разъемы DVI

CoreTM i7 / i5 / i3 2-го поколения в

Ivy Bridge, DDR3 1333 с

Extreme Memory Proﬁ le (XMP)1.3/1.2 с

Ivy Bridge. В

HD: Intel®

Ivy Bridge, Pixel

Русский

ASRock H61M-DG3/USB3 Motherboard

Page 70

Русский

- Подержат Blu-луч 1080p (КОММУТАЦИОННАЯ ДОСКА) / воспроизведение HD-DVD через разъемы DVI Аудиосистема - 5.1 CH HD Аудио HD (Кодер-декодер Аудио Realtek ALC662) ЛВС - PCIE x 1 Gigabit LAN 10/100/1000 Mb/s

- Realtek RTL8111E

- поддержка Wake-On-LAN

- Поддержка определения кабеля ЛВС

- Поддержка энергосберегающего интерфейса Ethernet 802.3az

- Поддержка PXE Разъемы ввода- I/O Panel вывода на задней - 1 x порт мыши PS/2 панели - 1 x порт клавиатуры PS/2

- 1 x D-Sub порт

- 1 x DVI-D порт

- 4 x порта USB 2.0 на задней панели в стандартной конфигурации

- 2 x порта USB 3.0 на задней панели в стандартной конфигурации

- Разъем 1 x RJ-45 LAN с светодиодным индикатором (индикатор ACT/LINK и индикатор SPEED)

- Соединитель звуковой подсистемы: линейный вход / передняя колонка / микрофон USB 3.0 - 2 x задних порта USB 3.0 на контроллере Etron EJ188H с поддержкой интерфейсов USB 1.1/2.0/3.0 и скорости передачи данных до 5 Гбит/с

- 1 x передний разъем USB 3.0 (поддерживает 2 порта USB 3.0) на контроллере Etron EJ188H с поддержкой интерфейсов USB 1.1/

2.0/3.0 и скорости передачи Колодки и - 4 x разъема SATA2 3,0 Гбит/с, поддержка функций NCQ, AHCI и плате «горячего подключения»

- 1 x Разъем порта печати

- 1 x Колодка COM

- 1 x разъем датчика открытой крышки

- 1 x соединитель CPU FAN (4-контактный)

- 1 x соединитель Chassis FAN (4-контактный)

- 1 x соединитель Power FAN (3-контактный)

- 24-контактный Колодка питания ATX

- 4-контактный Разъем ATX 12 В

- Аудиоразъем передней панели

- 2 x Колодка USB 2.0 (одна колодка для поддержки 4 дополнительных портов USB 2.0

- 1 x дополнительных портов USB 3.0) BIOS - 32Mb AMI BIOS

- AMI UEFI Legal BIOS с поддержкой графического интерфейса поль зователя

- поддержка “Plug and Play”

- ACPI 1.1, включение по событиям

- поддержка режима настройки без перемычек

- поддержка SMBIOS 2.3.1

Колодка USB 3.0 (одна колодка для поддержки 2

данных до 5 Гбит/с

ASRock H61M-DG3/USB3 Motherboard

Page 71

- центральный IGPU, DRAM, Мультирегулирование Напряжения PCH, CPU PLL, VTT, VCCSA Компакт- диск - Драйверы, служебные программы, антивирусное программное поддержки обеспечение (пробная версия), Пробная версия программы CyberLink MediaEspresso 6.5, ASRock MAGIX Multimedia Suite поставщик Контроль - Датчики температуры процессора оборудо- - Датчики температуры корпуса вания - Тахометры вентиляторов CPU/Chassis/Power FAN

- Бесшумный вентилятор ЦП/системного блока (возможность авто матической настройки скорости вентилятора системного блока в соответствии с температурой центрального процессора)

- Мультиконтроль скорости вентилятора ЦП/системного

- Определение открытой крышки

- Контроль напряжения: +12V, +5V, +3.3V, Vcore Операцион - Совместимость с Microsoft® Windows® 7 / 7 64-bit / Vista Поддержка 64-разрядной версии Vista ные системы - FCC, CE, WHQL Сертификаты - Совместимость с ErP/EuP Ready (требуется блок питания совместимый с ErP/EuP) * Для детальной информации продукта, пожалуйста посетите наш вебсайт: http://www.asrock.com

/ XP / XP 64-bit

1.3 Установка перемычек

Конфигурация перемычек иллюстрируется на рисунке. Когда перемычка надета на контакты, они называются “замкнутыми” (short). Если на контактах перемычки нет, то они называются “разомкнутыми” (open). На иллюстрации показана 3-контактная перемычка, у которой контакты 1 и 2 замкнуты.

Перемычка Установка Описание

Очистка CMOS

(CLRCMOS1, 3-контактная перемычка) (см. стр. 2, п. 21)

Примечание.

Контактная колодка CLRCMOS1 позволяет очистить данные CMOS. Для очистки данных и восстановления заводских системных параметров сначала выключите компьютер и отсоедините сетевую вилку кабеля питания от электророзетки. Выждите не менее 15 секунд и колпачковой перемычкой на 5 секунд перемкните штырьки 2 и 3 контактной колодки CLRCMOS1. Однако не

Стандартные Очистка CMOS

ASRock H61M-DG3/USB3 Motherboard

Русский

Page 72

производите очистку CMOS непосредственно после обновления BIOS. Если необходимо

очистить CMOS сразу же после окончания обновления BIOS, то, перед очисткой CMOS, необходимо сначала выполнить загрузку системы, а затем завершить ее работу. Примите во внимание, что пароль, дата, время, профиль пользователя по умолчанию, идентификатор 1394 GUID и MAC-адрес будут очищены только тогда, когда будет извлечена из своего гнезда

батарейка CMOS.

1.4 Колодки и разъемы на плате

Имеющиеся на плате колодки и разъемы НЕ ЯВЛЯЮТСЯ контактами для перемычек. НЕ УСТАНАВЛИВАЙТЕ перемычки на эти колодки и разъемы – это приведет к необратимому повреждению материнской платы!

Разъемы Serial ATAII Четыре соединителя Serial ATAII

(SATA2_0, см. стр. 2, п. 10) (SATA2_1, см. стр. 2, п. 8) (SATA2_2, см. стр. 2, п. 12) (SATA2_3, см. стр. 2, п. 11)

кабелей SATAII. В настоящее время интерфейс SATA допускает скорость передачи данных до \ 3,0 Гбит/с.

Информационный Информационный кабель кабель Serial ATA (SATA) интерфейса SATA / SATAII

(дополнительно)

не является направленным. Любой из его соединителей может быть подключен либо к жесткому диску интерфейса SATAII либо к материнской плате.

предназначаются для

SATA2_3

SATA2_1

подключения внутренних

устройств хранения с

использованием интерфейсных

SATA2_2

SATA2_0

Русский

Колодка USB 2.0 Помимо Четыре стандартных

(9-контактный USB6_7) (см. стр. 2, п. 15)

портов USB 2.0 на панели ввода-

вывода, на данной материнской плате предусмотрено два разъема USB 2.0. Каждый разъем USB 2.0 поддерживает два порта USB 2.0.

(9-контактный USB8_9) (см. стр. 2, п. 16)

USB_PWR

P-9

P-8

USB_PWR

P+8

P+9

GND

DUMMY

ASRock H61M-DG3/USB3 Motherboard

Page 73

Колодка USB 3.0 Помимо два стандартных

(19-контактный USB3_2_3) (см. стр. 2, п. 24)

плате предусмотрен один разъем USB 3.0. Этот разъем USB 3.0 поддерживает два порта USB 3.0.

портов USB 3.0 на панели ввода-

Vbus

IntA_P0_SSRX-

IntA_P0_SSRX+

GND

IntA_P0_SSTX-

IntA_P0_SSTX+

GND

IntA_P0_D-

IntA_P0_D+

VbusVbus

IntA_P1_SSRX-

IntA_P1_SSRX+

GND

IntA_P1_SSTX-

IntA_P1_SSTX+

GND

IntA_P1_D-

IntA_P1_D+

DUMMY

вывода, на данной материнской

Разъем порта печати Это интерфейс кабеля порта

(25-выводов LPT1) (см. cтр. 2, п.18)

подключение принтеров.

Аудиоразъем передней Этот интерфейс предназначен панели для присоединения

(9-контактный HD_AUDIO1) (см. cтр. 2, п. 19)

обеспечивающего удобное подключение аудиоустройств и управление ими.

AFD#

печати, обеспечивающий удобное

ERROR#

PINIT#

SLIN#

SPD2

SPD1

SPD0

STB#

аудиокабеля передней панели,

SPD3

SPD4

SPD6

SPD5

GND

PRESENCE#

MIC2_R

MIC2_L

GND

SPD7

MIC_RET

J_SENSE

OUT2_R

ACK#

OUT_RET

OUT2_L

BUSY

SLCT

1. Система High Deﬁ nition Audio поддерживает функцию автоматического обнаружения разъемов (Jack Sensing), однако для ее правильной pаботы кабель панели в корпусе должен поддерживать HDA. При сборке системы следуйте инструкциям, приведенным в нашем руководстве и руководстве пользователя для корпуса.

2. Если вы используете аудиопанель AC’97, подключите ее к колодке аудиоинтерфейса передней панели следующим образом: A. Подключите

выводы Mic_IN (MIC) к контактам MIC2_L. B. Подключите выводы Audio_R (RIN) к контактам OUT2_R, а выводы Audio_L (LIN) к контактам OUT2_L. C. Подключите выводы Ground (GND) к контактам Ground (GND).

D. Контакты MIC_RET и OUT_RET предназначены только для аудиопанели HD. При использовании аудиопанели AC’97

подключать их не нужно.

E. Процедура активации микрофона приведена ниже.

Для ОС Windows

XP / XP 64-бита: Выберите «Mixer» (Микшер). Выберите «Recorder» (Устройство записи). Затем щелкните «FrontMic» (Передний микрофон).

Русский

ASRock H61M-DG3/USB3 Motherboard

Page 74

Русский

Для ОС Windows® 7 / 7 64-бита, VistaTM / VistaTM 64-бита: Перейдите к вкладке «FrontMic» (Передний микрофон) в панели управления Realtek. Отрегулируйте уровень «Recording Volume» (Громкость записи).

Колодка системной панели Данная колодка обеспечивает

(9-контактный PANEL1) (см. стр. 2, п. 14)

Подключите к этому разъему кнопку питания, кнопку сброса и индикатор состояния системы на корпусе в соответствии с указанным ниже назначением контактов. При подключении кабелей необходимо соблюдать полярность положительных и отрицательных контактов.

PWRBTN (кнопка питания):

Подключите к этим контактам кнопку питания на передней панели корпуса. Способ выключения системы с можно настроить.

RESET (кнопка сброса):

Подключите к этим контактам кнопку сброса на передней панели корпуса. Нажмите кнопку сброса для перезагрузки компьютера, если компьютер «завис» и нормальную перезагрузку выполнить не удается.

PLED (индикатор питания системы):

Подключите к этим контактам индикатор состояния питания на передней панели работает. Индикатор мигает, когда система находится в режиме ожидания S1. Этот индикатор не светится, когда система находится в режиме ожидания S3 или S4, либо выключена (S5).

HDLED (индикатор активности жесткого диска):

Подключите к этим контактам индикатор активности жесткого диска на передней панели корпуса. Этот индикатор светится, когда осуществляется считывание или запись данных на жестком диске.

работу нескольких функций

передней панели системы.

помощью кнопки питания

корпуса. Этот индикатор светится, когда система

Конструкция передней панели может различаться в зависимости от корпуса. Модуль передней панели в основном состоит из кнопки питания, кнопки сброса, индикатора питания, индикатора активности жесткого диска, динамика и т.п. При подключении к этому разъему модуля передней панели корпуса подключаются к соответствующим контактам.

удостоверьтесь, что провода

ASRock H61M-DG3/USB3 Motherboard

Page 75

Колодка динамика корпуса Подключите к этой колодке

(4-контактный SPEAKER1) (см. стр. 2, п. 13)

кабель от динамика на корпусе

компьютера.

Chassis и Power Fan-соединители

(4-контактный CHA_FAN1) (см. стр. 2, п. 9)

Подключите кабели вентилятора к соединителям и присоедините черный шнур к штырю заземления.

(3-контактный PWR_FAN1) (см. стр. 2, п. 25)

Разъем вентилятора Подключите к этому разъему процессора кабель вентилятора процессора

(4-контактный CPU_FAN1) (см. стр. 2, п. 3)

соответствовал контакту земли.

4 3 2 1

так, чтобы черный провод

FAN_SPEED_CONTROL

GND

+12V

CPU_FAN_SPEED

Данная материнская плата поддерживает вентиляторы процессора с 4-контактным разъемом (функция тихого режима вентилятора), однако вентиляторы с 3-контактным разъемом также будут успешно работать, хотя функция управления скоростью вращения вентилятора окажется недоступной. Если вы хотите подключить вентилятор процессора с 3-контактным разъемом к разъему вентилятора процессора на данной материнской плате,

для этого

следует использовать контакты 1-3.

Контакты 1-3 подключены

Установка вентилятора с 3-контактным разъемом

Колодка питания ATX Подключите к этой колодке

(24-контактный ATXPWR1) (см. стр. 2, п. 4)

кабель питания ATX.

12 124

Несмотря на то, что эта материнская плата предусматр- ивает 24-штыревой разъем питания ATX, работа будет продолжаться, даже если адаптируется традиционный 20-штыревой разъем питания ATX. Для использования 20-штыревого разъема питания ATX вставьте источник питания вместе со штекером 1 и штекером 13.

Установка 20-штыревого разъема питания ATX

ASRock H61M-DG3/USB3 Motherboard

Русский

Page 76

Колодка питания 12V-ATX Обратите внимание, что к этому

(4-контактный ATX12V1) (см. стр. 2, п. 1)

разъему необходимо

подключить вилку блока питания ATX 12 В, чтобы обеспечить достаточную мощность электропитания. В противном случае включение системы будет невозможно.

Колодка COM-порта Данная колодка COM-порта

(9-контактный COM1) (см. стр. 2, п. 17)

позволяет подключить модуль

порта COM.

Русский

Датчик открытой крышки Эта материнская плата

(2-контактный CI1) (см. стр. 2, п. 22)

поддерживает функцию

определения открытой крышки,

Signal

GND

которая позволяет определить, была ли снята крышка корпуса. Функция требует поддержку со стороны корпуса.

ASRock H61M-DG3/USB3 Motherboard

Page 77

2. Информация о BIOS

Утилита настройки BIOS (BIOS Setup) хранится во флэш-памяти на материнской плате. Чтобы войти в программу настройки BIOS Setup, при запуске компьютера нажмите <F2> или <Del> во время самопроверки при включении питания (Power-On-Self-Test – POST). Если этого не сделать, то процедуры тестирования POST будут продолжаться обычным образом. Если вы захотите вызвать BIOS Setup уже после POST, перезапустите систему с помощью клавиш <Ctrl> + <Alt> + <Delete> или нажатия кнопки сброса системы. Подробную информацию о программе BIOS Setup вы найдете в Руководстве пользователя (в формате PDF) на компакт-диске поддержки.

на корпусе

3. Информация о компакт-диске поддержки с программным обеспечением

Данная материнская плата поддерживает различные операционные системы Microsoft®

Windows

компакт-диск поддержки содержит необходимые драйверы и полезные утилиты, которые расширяют возможности материнской платы. Чтобы начать работу с компакт-диском поддержки, вставьте его в дисковод CD-ROM. Если в вашем компьютере включена функция автозапуска (AUTORUN), то на экране автоматически появится главное меню компакт-диска (Main Menu). Если этого не произошло, найдите в папке BIN на компакт-диске поддержки файл ASSETUP.EXE и дважды щелкните на нем, чтобы открыть меню.

: 7 / 7 64-bit / VistaTM / VistaTM 64-bit / XP / XP 64-bit. Поставляемый вместе с ней

ASRock H61M-DG3/USB3 Motherboard

Русский

Page 78

1. Introdução

Gratos por comprar nossa placa–mãe H61M-DG3/USB3 um produto conﬁ ável feito com ASRock um estrito controle de qualidade consistente. Com um excelente desempenho, essa placa é dotada de um projeto robusto que atende a ASRock de compromisso com a qualidade e durabilidade. Este Guia de Instalação Rápida apresenta a placa-mãe e o guia de instalação passo a passo. Mais informações detalhadas sobre a placa-mãe podem ser encontradas no manual do usuário do CD de suporte.

Português

poderiam ser atualizados, o conteúdo deste manual pode ser cambiado sem aviso. Em caso de qualquer modiﬁ cação deste manual, a versão atualizada estará disponível no website de ASRock sem prévio aviso. Pode também encontrar as listas das mais recentes placas VGA e das CPUs suportadas no site da web da ASRock. Website de ASRock http://www.asrock.com Se precisar de apoio técnico em relação a este placa-mãe, por favor visite o nosso sítio da internet para informação especíﬁ ca acerca do modelo que está a utilizar. www.asrock.com/support/index.asp

Porque as especiﬁ cações da placa mãe e o software de BIOS

1.1 Este pacote contém

Placa-mãe ASRock H61M-DG3/USB3 (Formato Micro ATX: 8,9 pol. x 6,8 pol., 22,6 cm x 17,3 cm) Guia de instalação rápida da ASRock H61M-DG3/USB3 CD de suporte da placa ASRock H61M-DG3/USB3 Dois cabo de dados ATA Serial (SATA) (Opcional) Uma proteção I/O

A ASRock recorda-lhe...

Para obter melhor desempenho em Windows® 7 / 7 64-bit / VistaTM / VistaTM 64-bit, recomendamos que deﬁ na a opção Conﬁ guração de Ar- mazenamento na BIOS para o modo AHCI. Para mais detalhes acerca da conﬁ guração da BIOS consulte o “Manual de utilizador” no nosso CD de suporte.

ASRock H61M-DG3/USB3 Motherboard

Page 79

1.2 Especiﬁ cações

Plataforma - Formato Micro ATX: 8,9 pol. x 6,8 pol., 22,6 cm x 17,3 cm

- Design de condensadores banhados a ouro de alta qualidade CPU - Suporta segunda geração Intel de LGA1155

- Suporta a tecnologia Intel

- Suporta K-Series desbloqueado CPU Chipsets - Intel

H61

- Suporta a tecnologia Rapid Start da Intel® e a tecnologia Smart Connect

Memória - Suporte à tecnologia de memória de duplo canal

- 2 x slots de DDR3 DIMM

- Suporte para memória não intermédia DDR3 1600/1333/1066, não ECC (DDR3 1600 com Intel com processadores Intel® Sandy Bridge CPU)

- Capacidade máxima de memória do sistema: 16GB

- Suporta Extreme Memory Proﬁ le (XMP)1.3/1.2 da Intel® com

CPU Ivy Bridge da Intel

Slots de - 1 x slot de PCI Express 3.0 x16 Expansão * O modo PCIE 3.0 apenas é suportado com a CPU Ivy Bridge da Intel® A CPU Sandy Bridge da Intel® apenas suporta o modo PCIE 2.0.

- 1 x slot de PCI Express 2.0 x1 VGA integrado * As saídas Intel

HD Graphics Built-in Visuals e VGA são

suportadas apenas por processadores com GPU integrada.

- Suporta Intel

HD Graphics Embutido Visuals: Intel® Quick Sync Video 2.0, Intel® InTruTM 3D, Intel® Clear Video HD Technology, Intel® InsiderTM, Intel® HD Graphics 2500/4000 com CPU Ivy Bridge da Intel®

- Suporta Intel® HD Graphics Embutido Visuals: Intel® Quick Sync Video, Intel® InTruTM 3D, Intel® Clear Video HD Technology, Intel

HD Graphics 2000/3000, Intel® Advanced

Vector Extensions (AVX) com CPU Sandy Bridge da Intel

- Pixel Shader 5.0, DirectX 11 com Intel® Ivy Bridge CPU, Pixel Shader 4.1, DirectX 10.1 com processadores Intel Bridge CPU

- Memória partilhada máxima 1760MB com CPU Ivy Bridge da

Intel®. Memória partilhada máxima 1759MB com CPU Sandy Bridge da Intel®.

- Porta de saída VGA dupla: suporta portas DVI-D e D-Sub

CoreTM i7 / i5 / i3 no Pacote

Turbo Boost 2.0

Ivy Bridge CPU, DDR3 1333

Sandy

Português

ASRock H61M-DG3/USB3 Motherboard

Page 80

Português

através de controladores de visualização independentes

- Suporta DVI com resolução máxima até 1920x1200 @ 60Hz

- Suporta D-Sub com resolução máxima até 2048x1536 @ 75Hz

- Suportar HDCP função com DVI porta

- Suportar 1080p Blu-ray (BD) / HD-DVD playback com DVI porta Áudio - Áudio de alta deﬁ nição de canal 5.1 (Codec de áudio Realtek ALC662) LAN - PCIE x1 Gigabit LAN 10/100/1000 Mb/s

- Realtek RTL8111E

- Suporta Wake-On-LAN

- Suporta Detecção de cabo LAN

- Suporta PXE Entrada/Saída I/O Panel pelo painel - 1 x porta para mouse PS/2 traseiro - 1 x porta para teclado PS/2

- 1 x porta D-Sub

- 1 x porta DVI-D

- 4 x portas USB 2.0 padrão

- 2 x portas USB 3.0 padrão

- 1 x porta LAN RJ-45 com LED (LED ACT/LIG e LED VELOCIDADE)

- Áudio Jack: saída / entrada de linha / microfone + porta de jogos USB3.0 - 2 x Portas USB 3.0 traseiras através de EJ188H da Etron, com suporte para USB 1.1/2.0/3.0 até 5Gb/s

- 1 x Conector USB 3.0 frontal (suporta 2 portas USB 3.0)

através de EJ188H da Etron, com suporte para USB 1.1/2.0/3.0 até 5Gb/s Conectores - 4 x conectores SATA2, suporte a taxa de transferência de dados de até 3,0 Gb/s, suporte NCQ, AHCI e “conexão a quente”

- 1 x Conector de Porta de Impressão

- 1 x conector da porta COM

- 1 x Conector de intrusão no chassis

- 1 x Conector do ventilador da CPU (4 pinos)

- 1 x Conector do ventilador da chassis (4 pinos)

- 1 x Conector do ventilador da energia (3 pinos)

- Conector de força do ATX de 24 pinos

- Suporta Ethernet com Eﬁ ciência Energética 802.3az

ASRock H61M-DG3/USB3 Motherboard

Page 81

- Conector ATX 12 V de 4 pinos

- Conector Áudio do painel frontal

- 2 x cabezal USB 2.0 (suporta 4 portas USB 2.0)

- 1 x cabezal USB 3.0 (suporta 2 portas USB 3.0) BIOS - 32Mb BIOS AMI

- BIOS UEFI oﬁ cial da AMI com suporte para GUI

- Suporta dispositivos “Plug and Play”

- ACPI 1.1 atendendo a eventos de “wake up”

- Suporta dispositivos sem jumper

- Suporte para SMBIOS 2.3.1

- IGPU, DRAM, PCH, CPU PLL, VTT, VCCSA Voltage Multi-adjustment CD de suporte - Controladores, utilitários, software antivírus (Experimentacao Versao), CyberLink MediaEspresso 6.5 versão de demonstração, ASRock MAGIX Multimedia Suite - OEM Monitor do HW - Sensores de temperature do procesador

- Medição de temperatura da placa-mãe

- Tacômetros de ventilador do Processador/chassis/energia

- Ventoinha silenciosa para a CPU/chassis (Permitir velocidade Chassis Auto-Ajuste de temperatura da CPU)

- CPU/Chassis Fan Controle Multi-Velocidade

- Detecção de ABERTURA da CAIXA

- Monitoramento de voltagem : +12 V, +5 V, +3.3 V, Vcore Sistema - Microsoft

Windows® 7 / 7 de 64 bits / Vista

/ Vista

de 64

Operacional bits / XP / XP de 64 bits Certiﬁ cações - FCC, CE, WHQL

- “ErP/EuP Ready” (é necessária alimentação eléctrica “ErP/ EuP Ready”)

* Para informações mais detalhadas por favor visite o nosso sítio Web: http://www.asrock.com

ASRock H61M-DG3/USB3 Motherboard

Português

Page 82

1.3 Conﬁ guração dos Jumpers

A ilustração mostra como os jumpers são conﬁ gurados. Quando há uma capa de jumpers sobre os pinos, diz–se que o jumper está “curto”. Não havendo capa sobre os pinos, o jumper está “aberto”. A ilustração mostra um jumper de 3 pinos em que os pinos 1 e 2 están “curtos” quando a capa de jumper estiver colocada sobre esses 2 pinos.

Jumper Conﬁ guração

Restaurar CMOS

(CLRCMOS1, jumper de 3 pinos) (veja a folha 2, No. 21)

Nota: CLRCMOS1 permite você limpar os dados em CMOS. Os dados em CMOS

incluem informações da conﬁ guração do sistema como: por exemplo a senha do sistema, data, tempo, e os parámetros da conﬁ guração do sistema. Para limpar e reconﬁ gurar os parámetros do sistema a conﬁ guração inicial da fá- brica, por favor desligue o cabo de força, ponha em curto–circuito os pin 2 e pin 3 de CLRCMOS1 por mais de 5 segundos para limpar o CMOS usando um jumper. Por favor lembrese de remover o jumper depois de limpar o COMS. Se precisar limpar o CMOS ao concluir a atualização do BIOS, deverá reiniciar o sistema primeiro e, em seguida, desligá-lo antes de executar a ação de limpeza o CMOS.

Conﬁ guração-padrão Limpar o CMOS

Português

ASRock H61M-DG3/USB3 Motherboard

Page 83

1.4 Conectores

Os conectores NÃO SÃO jumpers. NÃO coloque capas de jumper sobre estes conectores. A colocação de pontos de jumper sobre os conectores causará danos irreversíveis à placa-mãe.

Conector Figura Descrição

Conectores ATAII Serial Estes quatro conectores Serial

(SATA2_0: veja a folha 2, No. 10)

(SATA2_1: veja a folha 2, No. 8)

(SATA2_2: veja a folha 2, No. 12)

(SATA2_3: veja a folha 2, No. 11)

SATA2_3

ATA (SATAII) suportam

unidades de disco rígido SATA

ou SATAII como dispositivos de

SATA2_2

armazenamento internos. A atual interface SATAII permite uma taxa de transferência de dados de até 3.0 Gb/s.

Cabo de dados Tanto a saída do cabo de Serial ATA (SATA) dados SATA pode ser

(opcional)

conectado ao disco rígido SATA / SATAII quanto o conector SATAII na placa mãe.

Cabezal USB 2.0 Além das quatro portas USB

(USB6_7 de 9 pinos)

(veja a folha 2, No. 15)

2.0 por defeito no painel de entrada/saída, há dois

ligações USB 2.0 nesta placa mãe. Cada ligação USB 2.0 pode suportar dois portas USB

(USB4_5 de 9 pinos)

(veja a folha 2, No. 16)

2.0.

USB_PWR

P-4

P-5

USB_PWR

SATA2_1

SATA2_0

P+4

GND

P+5

DUMMY

Cabezal USB 3.0 Além das dois portas USB 3.0

(USB3_2_3 de 19 pinos)

(veja a folha 2, No. 24)

por defeito no painel de

entrada/saída, há um ligações USB 3.0 nesta placa-mãe. Cada ligação USB 3.0 pode suportar dois portas USB 3.0.

Vbus

IntA_P0_SSRX-

IntA_P0_SSRX+

GND

IntA_P0_SSTX-

IntA_P0_SSTX+

GND

IntA_P0_D-

IntA_P0_D+

VbusVbus

IntA_P1_SSRX-

IntA_P1_SSRX+

GND

IntA_P1_SSTX-

IntA_P1_SSTX+

GND

IntA_P1_D-

IntA_P1_D+

DUMMY

ASRock H61M-DG3/USB3 Motherboard

Português

Page 84

Conector de Porta de Impressão Esta é uma interface para um

(LPT1 de 25 pinos)

(veja a folha 2, No. 18)

prática para dispositivos de impressão.

AFD#

cabo de porta de impressão

ERROR#

PINIT#

que permite uma ligação

SLIN#

SPD2

SPD1

SPD0

STB#

SPD3

SPD4

SPD5

SPD6

GND

SPD7

ACK#

BUSY

SLCT

Conector Áudio do painel Esta é uma interface para o frontal cabo de áudio no painel frontal,

(HD_AUDIO1 de 9 pinos)

(veja a folha 2, No. 19)

que permite uma conexão e

controle convenientes dos

dispositivos de áudio.

GND

PRESENCE#

MIC2_R

MIC2_L

MIC_RET

J_SENSE

OUT2_R

OUT_RET

OUT2_L

1. Áudio de elevada deﬁ nição que suporta a sensibilidade da tomada, mas o ﬁ o do painel existente no chassis tem de suportar HDA para funcionar correctamente. Siga s instruções que aparecem no manual e no manual do chassis para instalar o sistema.

2. Se utilizar o painel de áudio AC’97, instale-o no cabeçalho de áudio do painel frontal, como a ﬁ gura abaixo mostra: A. Ligue o Mic_IN (MIC) ao MIC2_L. B. Ligue o Audio_R (RIN) ao OUT2_R e o Audio_L (LIN) ao OUT2_L. C. Ligue o Ground (GND) ao Ground (GND). D. MIC_RET e OUT_RET são apenas para o painel de áudio HD. Não necessita de os ligar para o painel de áudio AC’97. E. Para activar o microfone frontal. Para os Sistemas Operativos Windows

XP / XP 64 bits: Seleccione “Misturador”. Seleccione “Gravador”. Depois clique em “Microfone frontal”. Para os Sistemas Operativos Windows

7 / 7 64-bit / VistaTM / VistaTM 64-bit: Aceda ao separador “Microfone frontal” no painel de Controlo Realtek. Ajuste o “Volume de gravação”.

Português

Conector do painel do sistema Este conector acomoda várias

(PANEL1 de 9 pinos)

(veja a folha 2, No. 14)

funções do painel frontal do

sistema.

ASRock H61M-DG3/USB3 Motherboard

Page 85

Ligue o botão de alimentação, o botão de reposição e o indicador do

estado do sistema no chassis a este conector de acordo com a descrição abaixo. Tenha em atenção os pinos positivos e negativos antes de ligar os cabos.

PWRBTN (Botão de alimentação): Ligue ao botão de alimentação no painel frontal do chassis. Pode conﬁ gu-

rar a forma para desligar o seu sistema através do botão de alimentação.

RESET (Botão de reposição):

Ligue ao botão de reposição no painel frontal do chassis. Prima o botão

de reposição para reiniciar o computador caso este bloqueie e não seja possível reiniciar normalmente.

PLED (LED de alimentação do sistema): Ligue ao indicador do estado da alimentação no painel frontal do chassis.

O LED ﬁ cará acesso quando o sistema estiver em funcionamento. O LED ﬁ cará intermitente quando o sistema estiver no estado de suspensão S1. O LED ﬁ cará desligado quando o sistema estiver nos estados de suspen- são S3/S4 ou desligado (S5).

HDLED (LED de actividade do disco rígido): Ligue ao LED de actividade do disco rígido no painel frontal do chassis. O

LED ﬁ cará acesso quando o disco rígido estiver a ler ou a escrever dados.

O design do painel frontal poderá variar dependendo do chassis. Um

módulo de painel frontal consiste principalmente em um botão de alimentação, um botão de reposição, um LED de alimentação, um LED de actividade do disco rígido, um altifalante, etc. Ao ligar o seu módulo de painel frontal do chassis a este conector, certiﬁ que-se que os ﬁ os e os pinos têm uma correspondência exacta.

Conector do alto-falante do chassi Ligue o alto-falante do chassi

(SPEAKER1 de 4 pinos)

(veja a folha 2, No. 13)

neste conector.

Conector do ventilador do chassis/energia Ligue o cabo do ventilador

(CHA_FAN1 de 4 pinos)

(veja a folha 2, No. 9)

neste conector, coincidindo o ﬁ o

preto com o pino de aterramen

to.

(PWR_FAN1 de 3 pinos) (veja a folha 2, No. 25)

ASRock H61M-DG3/USB3 Motherboard

Português

Page 86

Conector do ventilador da Ligue o cabo do ventilador da

4 3 2 1

CPU CPU, coincidindo o ﬁ o preto

(CPU_FAN1 de 4 pinos)

(veja a folha 2, No. 3)

com o pino de aterramento.

FAN_SPEED_CONTROL

Apesar de esta placa-mãe possuir 4 apoios para uma ventoinha de CPU (Ventoinha silenciosa), uma ventoinha de 3 pinos para CPU poderá funcionar mesmo sem a função de controlo de velocidade da ventoinha. Se pretender ligar uma ventoinha de 3 pinos para CPU ao conector de ventoinha do CPU nesta placa-mãe, por favor, ligue-a aos pinos 1-3.

GND

+12V

CPU_FAN_SPEED

Pinos 1-3 ligados

Instalação de Ventoinha de 3 pinos

Português

Conector de força do ATX Ligue a fonte de alimentação

(ATXPWR1 de 24 pinos)

(veja a folha 2, No. 4)

Embora esta placa-mãe providencie um conector de energia ATX de 24 pinos, pode apesar disso funcionar

ATX neste conector.

12 124

com a adapta-ção de uma fonte de energia tradicional de 20 pinos. Para usar a fonte de alimentação de 29 pinos, por favor ligue a sua fonte de alimentação com o Pino 1 e o Pino 13.

Instalação da Fonte de alimentação ATX de 20 Pinos

Conector ATX 12 V Note que é necessário ligar

(ATX12V1 de 4 pinos)

(veja a folha 2, No. 1)

uma fonte de alimentação com

conector ATX 12V neste conector para fornecer alimentação suﬁ ciente. Do contrário, haverá falhas de funcionamento.

Conector da porta COM

(COM1 de 9 pinos)

(veja a folha 2, No. 17)

suportar um módulo de porta

Este conector é usado para

COM.

ASRock H61M-DG3/USB3 Motherboard

Page 87

Conector de intrusão no chassis Esta placa principal suporta a

(CI1 de 2 pinos)

(veja a folha 2, No. 22)

função de detecção de

ABERTURA da CAIXA

Signal

GND

quedetecta se a tampa do chassisfoi removida. Esta funçãorequer um chassis com designde detecção de intrusão.

ASRock H61M-DG3/USB3 Motherboard

Português

Page 88

2. Informações da BIOS

O Utilitário de Conﬁ guração do BIOS está armazenado no chip FWH do BIOS. Ao iniciar o computador, pressione <F2> ou <Del> durante o Autoteste de iniciação (POST) para acessar o Utilitário de Conﬁ guração do BIOS; caso contrário, o POST continuará com as rotinas de teste. Se desejar acessar o Utilitário de Conﬁ guração do BIOS depois do POST, reinicie o sistema pressionando <Ctl> + <Alt> + <Del>, ou pressionando o botão de reinício no chassi do sistema. Para as informações detalhadas sobre o Utilitário de Conﬁ guração do BIOS, consulte o Manual do Usuário (arquivo PDF) no CD de suporte.

3. Informações do CD de Suporte

Esta placa Mãe suporta vários sistemas operacionais: Microsoft® Windows®: 7 / 7 de 64 bits / VistaTM / VistaTM de 64 bits / XP / XP de 64 bits. O CD de instalação que acompanha a placa Mãe contem: drivers e utilitários necessários para um melhor desempenho da placa Mãe. Para começar a usar o CD de instalação, introduza o CD na leitora de CD-ROM do computador. Automaticamente iniciará o menu principal, casa o AUTORUN esteja ativado. Se o menu principal não aparecer automaticamente, explore o CD e execute o “ASSETUP.EXE” localizado na pasta BIN.

Português

ASRock H61M-DG3/USB3 Motherboard

Page 89

1. Giriş

ASRock’ın kesintisiz titiz kalite denetimi altında üretilen güvenilir bir anakart olan ASRock H61M-DG3/USB3 anakartını satın aldığınız için teşekkür ederiz. ASRock’ın kalite ve dayanıklılık konusundaki kararlılığına uygun güçlü tasarımıyla mükemmel bir performans sunar.

Bu Hızlı Takma Kılavuzu anakarta giriş ve adım adım takma kılavuzu içerir. Anakart hakkında daha ayrıntılı bilgiyi Destek CD’sinde sunulan kullanıcı kılavuzunda bulabilirsiniz.

Anakart özellikleri ve BIOS yazılımı güncelleştirilebileceğinden bu kılavuzun içeriği önceden haber verilmeksizin değişebilir. Bu belgede değişiklik yapılması durumun

-da, güncelleştirilmiş sürüm ayrıca haber verilmeksizin ASRock web sitesinde sunulur. En son VGA kartlarını ve CPU destek listelerini de ASRock web sitesinde bulabilirsiniz. ASRock web sitesi http://www.asrock.com

Bu anakartla ilgili teknik desteğe ihtiyacınız olursa, kullandığınız modele özel bilgiler için lütfen web sitemizi ziyaret edin. www.asrock.com/support/index.asp

1.1 Paket İçindekiler

ASRock H61M-DG3/USB3 Anakart (Micro ATX Form Faktörü: 8,9-inç x 6,8-inç, 22,6 cm x 17,3 cm) ASRock H61M-DG3/USB3 Hızlı Takma Kılavuzu ASRock H61M-DG3/USB3 Destek CD’si 2 x Seri ATA (SATA) Veri Kablosu (İsteğe Bağlı) 1 x G/Ç Panel Kalkanı

ASRock Size Şunu Hatırlatır...

Windows® 7 / 7 64-bit / Vista elde etmek için, Depolama Konﬁ gürasyonundaki BIOS seçeneğini AHCI moduna ayarlamanız tavsiye edilir. BIOS ayarı için, ayrıntıları öğrenmek üzere lütfen destek CD'mizdeki "Kullanıcı Kılavuzu"na bakın.

/ VistaTM 64-bit ile daha iyi performans

ASRock H61M-DG3/USB3 Motherboard

Türkçe

Page 90

Türkçe

1.2 Özellikler

Platform - Micro ATX Form Faktörü: 8,9-inç x 6,8-inç, 22,6 cm x 17,3 cm

- Tüm Katı Kapasitör tasarımı CPU - Nesil Intel

- Intel® Turbo Boost 2.0 Teknolojisini destekler

- K-Serisi kilidi kaldırılmış işlemciyi destekler Yonga seti - Intel® H61

- Intel® Rapid Start Teknolojisini ve Smart Connect Teknolojisi’ni destekler Bellek - Çift Kanallı DDR3 Belleği Teknolojisi

- 2 x DDR3 DIMM yuva

- DDR3 1600/1333/1066 ECC olmayan, ara belleksiz bellek (Intel Bridge işlemciye sahip DDR3 1333)

- Sistem belleğinin maks. kapasitesi: 16 GB

- Intel (XMP)1.3/1.2 destekler Genişletme - 1 x PCI Express 3.0 x16 yuva Yuvası * PCIE 3.0, sadece Intel Intel® Sandy Köprü İşlemciyle, sadece PCIE 2.0'ı destekler.

- 1 x PCI Express 2.0 x1 yuva Graﬁ kler * Intel GPU entegre işlemciler tarafından desteklenmektedir.

- Intel® Ivy Bridge İşlemci ile Intel® HD Graphics Dahili Görselleri: Intel Intel® Clear Video HD Teknolojisi, Intel® InsiderTM, Intel® HD Graphics 2500/4000

- Intel® Sandy Bridge İşlemci ile Intel® HD Graphics Dahili Görselleri: Intel® Hızlı Eşitleme Videosu, Intel® InTruTM 3D, Intel 2000/3000, Intel® Gelişmiş Vektör Uzantıları (AVX)

- Pixel Shader 5.0, Intel® Ivy Bridge işlemciye sahip DirectX 11. Pixel Shader 4.1,Intel® Sandy Bridge işlemciye sahip DirectX

10.1

- Intel Intel® Sandy Bridge İşlemci ile Maks. paylaюэlan bellek 1759 MB.

- Çift VGA Çıkış: desteği DVI-D ve bağımsız görüntü denetleyiciler tarafından D-Sub bağlantı noktaları

- 60Hz’de 1920x1200’e kadar maks. зцzьnьrlьkle DVI’yэ

CoreTM i7 / i5 / i3 in LGA1155 Paketini destekle

Ivy Bridge işlemciye sahip DDR3 1600, Intel® Sandy

Ivy Bridge İşlemci ile Intel® Extreme Bellek Proﬁ lini

Ivy Köprü İşlemcisiyle desteklenir.

HD Graﬁ k Yerleşik Görselleri ve VGA çıkışları, yalnızca

Hızlı Eşitleme Videosu 2.0, Intel® InTruTM 3D,

Clear Video HD Teknolojisi, Intel® HD Graphics

Ivy Bridge İşlemci ile Maks. paylaюэlan bellek 1760 MB.

ASRock H61M-DG3/USB3 Motherboard

Page 91

destekler

- 75Hz’de 2048x1536’ya kadar maks. зцzьnьrlьkle D-Sub’э destekler

- DVI portlarэyla HDCP iюlevini destekler

- DVI portlarэyla Tam HD 1080p Blu-ray (BD) / HD-DVD oynatэmэnэ destekler Ses - (Realtek ALC662 Ses Codec’i) 5,1 Kanal HD Ses LAN - PCIE x1 Gigabit LAN 10/100/1000 Mb/sn

- Realtek RTL8111E

- LAN’da Uyan özelliğini destekler

- LAN Kablo Algılama’yı destekler

- Enerji Verimli Ethernet 802.3az desteği

- PXE’yi destekler Arka Panel G/З Paneli G/З - 1 x PS/2 Fare Portu

- 1 x PS/2 Klavye Portu

- 1 x D-Sub Portu

- 1 x DVI-D Portu

- 4 x Kullanэma Hazэr USB 2.0 Portu

- 2 x Kullanэma Hazэr USB 3.0 Portu

- 1 x RJ-45 LAN Portu, LED’li (AKT/LЭNK LED’i ve HIZ LED’i)

- HD Ses Jakı: Hat Girişi/Ön Hoparlör/Mikrofon USB 3.0 - Etron EJ188H tarafından 2 x Arka USB 3.0 bağlantı noktası, 5Gb/s’ye kadar USB 1.1/2.0/3.0

- Etron EJ188H tarafından 1 x Ön USB 3.0 bağlantısı (2 USB 3.0 bağlantı noktasını destekler), 5Gb/s’ye kadar USB 1.1/2.0/3.0 Konektör Bileşen Takma” işlevlerini

- 1 x Yazdэrma Portu ﬁ юi

- 1 x COM portu ﬁ şi

- 1 x Kasaya Yetkisiz Erişim ﬁ şi

- 1 x Conector do ventilador da CPU (4 pinos)

- 1 x Conector do ventilador da chassis (4 pinos)

- 1 x Conector do ventilador da energia (3 pinos)

- 24 pin ATX güç konektörü

- 4 pin 12V güç konektörü

- Ön panel ses konektörü

- 2 x USB 2.0 ﬁ ş (4 USB 2.0 portu destekler)

- 1 x USB 3.0 ﬁ ş (2 USB 3.0 portu destekler) BIOS Özelliği - 32 Mb AMI BIOS

- “Tak Çalıştır”ı destekler

- 4 x SATA2 3,0Gb/sn, donanım NCQ, AHCI ve “Sistem Açıkken

GUI destekli AMI UEFI Geçerli BIOS

ASRock H61M-DG3/USB3 Motherboard

Türkçe

Page 92

- ACPI 1.1 Uyumlu Uyandırma Olayları

- Jumpersız ayarlamayı destekler

- AMBIOS 2.3.1 Desteği

- IGPU, DRAM, PCH, CPU PLL, VTT, VCCSA Voltaj Çoklu ayarı Destek CD’si - Sürücüler, Yardımcı Programlar, AntiVirüs Yazılımı (Deneme Sürümü), CyberLink MediaEspresso 6.5 Deneme Sürümü, ASRock MAGIX Multimedya Seti - OEM Donanım - CPU Sıcaklık Duyarlılığı Monitör - Kasa Sıcaklık Duyarlılığı

- CPU/Kasa/Güç Fan Takometresi

- İşlemci/Kasa Sessiz Fanı (Kasa Fan Hızı’nın İşlemci sıcaklığı ile Otomatik Ayar’ına izin verir)

- CPU/Kasa Fan Çoklu-Hız Kontrolü

- KASA AÇIK algılaması

- Voltaj İzleme: +12V, +5V, +3,3V, CPU Vcore İS - Microsoft

Windows® 7 / 7 64-bit / VistaTM / VistaTM 64-bit / XP /

XP 64-bit uyumlu Sertiﬁ kalar - FCC, CE, WHQL

- ErP/EuP Hazır (ErP/EuP hazır güç kaynağı gerekli)

* Ayrıntılı ürün bilgileri için lütfen web sitemizi ziyaret edin: http://www.asrock.com

1.3 Jumper'ların Ayarı

Şekilde jumper'ların nasıl ayarlandıkları gösterilmektedir. Jumper kapağı pinler üzerine yerleştirildiğinde jumper "Kapalı" dır. Jumper kapağı pinler üzerindeyken jumper "Açık" tır. Şekilde pin1 ve pin2'si "Kapalı" olan jumper kapağı bu 2 pine yerleştirilmiş 3-pinli jumper gösterilmektedir.

Türkçe

Jumper Ayar

CMOS’u temizleme

(CLRCMOS1, 3-pinli jumper) (bkz. s.2 No. 21)

Not:

CLRCMOS1, CMOS’daki verilerinizi temizlemenize olanak sağlar. Sistem parametrelerini temizlemek ve varsayılan ayara sıfırlamak için lütfen bilgisayarı kapatın ve güç kablosunun ﬁ şini güç kaynağından çekin. 15 saniye bekledikten sonra, pin2 ve pin3‘ü CLRCMOS1’de 5 saniye kısaltmak için bir atlatıcı şapkası kullanın. Ancak, BIOS’u güncelledikten hemen sonra lütfen CMOS’u temizlemeyin. BIOS’u güncellemeyi tamamladığınızda CMOS’u temizlemeniz gerekirse,

ASRock H61M-DG3/USB3 Motherboard

Clear CMOSDefault

Page 93

ilk olarak sistemi başlatmanı z ve ardından CMOS temizleme işlemini

gerçekleştirmeden önce kapatmanız gereklidir. Parola, tarih, saat, kullanıcı varsayılan proﬁ li, 1394 GUID ve MAC adresinin yalnızca CMOS pili çıkarıldığında temizleneceğini lütfen aklınızda bulundurunuz.

1.4 Yerleşik Fişler ve Konektörler

Yerleşik ﬁ şler ve konektörler jumper DEĞİLDİR. Bu ﬁ şlerin ve konektörlerin üzerine jumper kapakları YERLEŞTİRMEYİN. Fişlerin ve konektörlerin üzerine jumper kapakları yerleştirmek anakartın kalıcı olarak zarar görmesine neden olabilir!

Seri ATAII Konektörler Bu dört Seri ATAII (SATAII)

(SATA2_0: bkz. s.2, No. 10)

(SATA2_1: bkz. s.2, No. 8)

(SATA2_2: bkz. s.2, No. 12)

(SATA2_3: bkz. s.2, No. 11)

SATA2_3

konektör, dahili depolama

cihazları için SATA veri

kablolarını destekler. Geçerli

SATA2_2

SATAII arayüzü 3,0 Gb/sn veri

SATA2_1

SATA2_0

aktarım hızına izin verir.

Seri ATA (SATA) SATA veri kablosunu her iki ucu Veri Kablosu da SATA / SATAII sabit

(İsteğe bağlı)

diskine veya anakarttaki SATAII konektörüne bağlanabilir.

USB 2.0 Fişleri G/Ç panelindeki varsayılan

(9-pinli USB6_7)

(bkz. s.2 No. 15)

dört USB 2.0 portundan başka,

bu anakartta iki USB 2.0 ﬁ şi bulunur. Her USB 2.0 ﬁ şi iki USB 2.0 portunu destekler.

Vbus

GND

IntA_P0_D-

IntA_P0_D+

USB_PWR

P-9

P-8

USB_PWR

P+9

GND

DUMMY

GND

P+8

VbusVbus

IntA_P1_SSRX-

IntA_P1_SSRX+

GND

IntA_P1_SSTX-

IntA_P1_SSTX+

GND

IntA_P1_D-

IntA_P1_D+

DUMMY

(9-pinli USB8_9) (bkz. s.2 No. 16)

USB 3.0 Fişleri I/O panelinde bulunan iki adet

(19-pinli USB3_2_3)

(bkz. s.2 No. 24)

kart üzerinde bir adet USB 3.0 bağlantısı bulunur. Bu USB 3.0

varsayılan USB 3.0 bağlantı

noktasının yanı sıra, bu ana

IntA_P0_SSRX-

IntA_P0_SSRX+

IntA_P0_SSTX-

IntA_P0_SSTX+

bağlantısı iki adet USB 3.0 bağlantı noktasını destekleyebilir.

ASRock H61M-DG3/USB3 Motherboard

Türkçe

Page 94

Yazdırma Portu Fişi Bu, yazdırma portu kablosu için

(25-pinli LPT1)

(bkz. s.2 No. 18)

yazıcı cihazlarının uygun

bağlanmasını sağlayan bir

arayüzdür.

AFD#

STB#

ERROR#

PINIT#

SPD1

SPD0

SLIN#

SPD2

SPD3

SPD4

SPD5

SPD6

GND

SPD7

ACK#

BUSY

SLCT

Türkçe

Ön Panel Ses Fişi Bu, panel ses kablosu için

(9-pinli HD_SES1)

(bkz. s.2 No. 19)

uygun bağlantı sağlayan ve

ses cihazlarını kontrol

etmeyi sağlayan bir arayüzdür.

GND

PRESENCE#

MIC2_R

MIC2_L

MIC_RET

J_SENSE

OUT2_R

OUT_RET

OUT2_L

1. Yükse Tanımlı Ses Jak Duyarlılığını destekler, ancak kasadaki panel kablosunun HDA'nın düzgün çalışmasını desteklemesi gerekir. Lütfen sisteminizi yüklemek için kılavuzumuzdaki ve kasa kılavuzundaki talimatları izleyin.

2. AC'97 ses paneli kullanıyorsanız, lütfen ön panel ses ﬁ şine aşağıdaki gibi takın:

A. Mic_IN'i (MIC) MIC2_L'ye bağlayın. B. Audio_R'yi (RIN) OUT2_R'ye ve Audio_L'yi (LIN) OUT2_L'ye bağlayın. C. Ground'u (GND) Ground'a (GND) bağlayın. D. MIC_RET ve OUT_RET yalnızca HD ses paneli içindir. Bunları AC’97 ses

paneli için bağlamanız gerekmez. E. Ön mikrofonu etkinleştirmek için Windows

XP / XP 64-bit İS için:

"Karıştırıcı"yı seçin. "Kaydedici"yi seçin. Sonra "Ön Mikrofon"u tıklatın.

Windows

7 / 7 64-bit / VistaTM / VistaTM 64-bit İS için: Realtek Kontrol panelinde "Ön Mikrofon" Sekmesine gidin. "Kayıt Ses Seviyesi"ni ayarlayın.

Sistem Paneli Fişi Bu ﬁ ş, birçok sistem ön paneli

(9-pinli PANEL1)

(bkz. s.2 No. 14)

işlevini barındırır.

Kasa üzerindeki güç anahtarını, sıfırlama anahtarını ve sistem durumu göstergesini aşağıdaki pin atamalarına göre bu bağlantıya bağlayın. Kabloları bağlamadan önce pozitif ve negatif pinlere dikkat edin.

ASRock H61M-DG3/USB3 Motherboard

Page 95

PWRBTN (Güç Anahtarı):

Kasa üzerindeki güç anahtarını ön panele bağlayın. Güç anahtarını kullanarak sisteminizi kapatma şeklinizi yapılandırabilirsiniz.

RESET (Sıfırlama Anahtarı):

Kasa üzerindeki sıfırlama anahtarını ön panele bağlayın. Bilgisayar donarsa veya normal bir yeniden başlatma gerçekleştirilemezse, bilgisayarı yeniden başlatmak için sıfırlama anahtarına basın.

PLED (Sistem Gücü LED’i):

Kasa üzerindeki güç durumu göstergesini ön panele bağlayın. Sistem çalışırken LED yanar. Sistem S1 uyku modunda iken LED yanıp sön meye devam eder. Sistem S3/S4 uyku modunda veya kapalı (S5) iken LED söner. HDLED (Sabit Disk Çalışma LED’i): Kasa üzerindeki sabit disk çalışma LED’ini ön panele bağlayın. Sabit disk veri okurken veya yazarken LED yanar.

Ön panel tasarımı kasaya göre değiş

iklik gösterebilir. Ön panel modülünde temel olarak güç anahtarı, sıfırlama anahtarı, güç LED’i, sabit disk çalışma LED’i, hoparlör vb. bulunur. Kasa ön panel modülünüzü bu bağlantıya bağlarken, kablo atamalarının ve pin atamalarının doğru biçimde eşleştirildiğinden emin olun.

Kasa Hoparlörü Fişi Lütfen kasa hoparlörünü bu ﬁ şe

(4-pinli SPEAKER1)

(bkz. s.2 No. 13)

bağlayın.

Kasa/güç Fan Konektörü Lütfen kasa fan kablolarını

(4-pinli CHA_FAN1)

(bkz. s.2 No. 9)

fanına bu konektöre bağlayın

ve siyah kabloyu toprak pinine

bağlayın.

(3-pinli PWR_FAN1) (bkz. s.2 No. 25)

CPU Fan Konektörü Lütfen fan kablolarını CPU

(4-pinli CPU_FAN1)

(bkz. s.2 No. 3)

fanına bu konektöre bağlayın

ve siyah kabloyu toprak pinine

bağlayın.

4 3 2 1

+12V

FAN_SPEED_CONTROL

CPU_FAN_SPEED

GND

Türkçe

ASRock H61M-DG3/USB3 Motherboard

Page 96

Bu anakart 4-Pinli CPU fan (Sessiz Fan) desteği sağlasa da, 3-Pinli CPU fan hızı kontrol işlevi olmadan bile hala başarılı bir şekilde çalışabilir. 3-Pinli CPU fanı bu konektördeki CPU fan konektörüne bağlamayı planlıyorsanız, lütfen Pin 1-3'e bağlayın.

Pin 1-3 Bağlı

3-Pinli Fanı Takma

ATX Güç Konektörü Lütfen bir ATX güç kaynağını

(24-pinli ATXPWR1)

(bkz. s.2 No. 4)

Bu anakart 24-pinli ATX güç konektörü sağlasa da

bu konektöre bağlayın.

12 124

geleneksel bir 20-pinli ATX güç kaynağı bağlarsanız da çalışabilir. 20-pinli ATX güç kaynağını kullanmak için, lütfen güç kaynağınızı Pin 1 ve Pin 13'le birlikte takın.

20-Pinli ATX Güç Kaynağını Takma

ATX 12V Güç Konektörü Lütfen bir ATX 12V güç

(4-pinli ATX12V1)

(bkz. s.2 No. 1)

kaynağını bu konektöre

bağlayın.

Seri port Fişi Bu COM1 ﬁ şi bir seri port

(9-pinli COM1)

(bkz. s.2 No. 17)

modülünü destekler.

Türkçe

Kasaya Yetkisiz Erişim Fişi Bu anakart, kasa kapağının

(2-pinli CI1)

(bkz. s.2 No. 22)

çıkarılıp çıkarılmadığını

algılayan KASA AÇIK algılama

Signal

GND

özelliğini destekler. Bu özellik, kasaya yetkisiz erişim tasarımına sahip bir kasa gerektirir.

ASRock H61M-DG3/USB3 Motherboard

Page 97

2. BIOS Bilgileri

Anakarttaki Flash Bellek BIOS Ayarları Yardımcı Programını içerir. Bilgisayarı başlattığınızda, lütfen Otomatik Güç Sınaması (POST) sırasında BIOS Ayarları yardımcı programına girmek için <F2> veya <Del> tuşuna basın; aksi halde, POST test rutinlerine devam eder. BIOS Ayarlarına POST'tan sonra girmek istiyorsanız, lütfen <Ctl> + <Alt> + <Delete> tuşlarına basarak veya sistem kasasındaki sıfırlama düğmesine basarak sistemi yeniden başlatın. BIOS Ayarları programı kullanıcı dostu olacak şekilde tasarlanmıştır. Çeşitli alt menüler arasında dolaşmanıza ve önceden belirlenen seçenekler arasından seçim yapmanıza izin veren menü tabanlı bir programdır. BIOS Ayarları hakkında ayrıntılı bilgi için, lütfen Destek CD'sinde bulunan Kullanıcı Kılavuzu'na (PDF dosyası) başvurun.

3. Yazılım Destek CD’si bilgileri

Bu anakart çeşitli Microsoft® Windows® işletim sistemleri destekler: 7 / 7 64-bit

/ Vista

/ VistaTM 64-bit / XP / XP 64-bit. Anakartla birlikte gelen Destek CD'si anakart özelliklerini genişleten gerekli sürücüleri ve kullanışlı yardımcı programları içerir. Destek CD'sini kullanmaya başlamak için, CD'yi CDROM sürücünüze takın. Bilgisayarınızda "OTOMATİK KULLAN" özelliği etkinleştirilmişse, Ana Menüyü otomatik olarak görüntüler. Ana Menü otomatik olarak görüntülenmezse, menüleri görüntülemek için Destek CD'sinin “BIN” klasöründeki "ASSETUP.EXE" dosyasını bulun ve çift tıklatın.

ASRock H61M-DG3/USB3 Motherboard

Türkçe

Page 98

1. 제품소개

ASRock은사용자에게 알립니다

ASRock 의 다 . 이 메인보드는 엄격한 품질관리 하에 생산되어진 신뢰성 있는 메인보드 입니다 . 이 제품은 고 품격 디자인과 함께 ASRock 의 우수한 품질과 최고의 안정성을 자랑하 고 있습니다 . 이 빠른 설치 안내서에는 마더보드에 대한 설명과 단계별 설치 방법이 실려 있습니다 . 마더보드에 대한 보다 자세한 내용은 지원 CD 의 사용 설명서에서 확 인할 수 있습니다 .

메인보드의 사양이나 바이오스가 업 데이트 되기 때문에 이 사용자 설명서의 내용은 예고 없이 변경되거나 바뀔 수가 있습니다 . 만일을 생각해서 이 사용자 설명서의 어떤 변경이 있으면 ASRock 의 웹 사이트에서 언제든지 업 데이트를 하실 수 있습니다 . 웹사 이트에서 최신 VGA 카드와 CPU 지원 목록을 확인할 수 있습니다 . ASRock 의 웹사이트 주소는 http://www.asrock.com 입니다 . 본 머더보드와 관련하여 기술 지원이 필요한 경우 당사 웹 사이트를 방문하 여 사용 중인 모델에 대한 특정 정보를 얻으십시오 .

1.1 패키지 내용

ASRock (Micro ATX 폼 팩터 : 8.9” x 6.8”, 22.6 x 17.3 cm) ASRock ASRock 시리얼 ATA (SATA) 데이터 케이블 2 개 ( 선택 사양 ) I/O 차폐 1 개

H61M-DG3/USB3

www.asrock.com/support/index.asp

H61M-DG3/USB3

메인 보드를 구매하여 주신것에 대하여 감사 드립니

마더보드

퀵 설치 가이드 지원 CD

ASRock은사용자에게 알립니다

Windows 위해서 Storage Configuration(스토리지 구성)에서 BIOS 옵션을 AHCI 모드로 설정하는 것이 좋습니다. BIOS 설정과 관련하여 자세한 내용은 지 원 CD에 포함된 “사용 설명서”를 참조하십시오.

한 국 어

7 / 7 64-비트 / Vista

...

/ VistaTM 64-비트의 성능을 향상시키기

ASRock H61M-DG3/USB3 Motherboard

Page 99

1.2 설명서

플랫폼 - Micro ATX 폼 팩터 : 8.9” x 6.8”, 22.6 x 17.3 cm

- 완전 고체 축전지 디자인 CPU - LGA1155 패키지의 2 세대 Intel

- Intel® Turbo Boost 2.0 기술 지원

- K- 시리즈 잠금 해제 CPU 지원 칩셋 - Intel

- Intel

H61

Rapid Start 기술과 Smart Connect 기술을 지원합니다

메모리 - 듀얼 채널 메모리 기술 지원

- DDR3 DIMM 슬롯 2 개

- DDR3 1600/1333/1066 비 -ECC, 언버퍼드 메모리를 지원 (Intel® Ivy Bridge CPU 를 탑재한 DDR3 1600, Intel® Sandy Bridge CPU 를 탑재한 DDR3 1333)

- 최대 시스템 메모리 용량 : 16GB

- Intel

Ivy Bridge CPU 에서 Intel® 익스트림 메모리 프로파일 (XMP)1.3/1.2 지원 확장 슬롯 - PCI Express 3.0 x16 슬롯 1 개 * PCIE 3.0 은 Intel

Ivy Bridge CPU 에서만 지원됩니다 .

Intel® Sandy Bridge CPU 는 PCIE 2.0 만 지원합니다 .

- PCI Express 2.0 x1 슬롯 1 개 온보드 VGA * Intel

HD Graphics 내장 비주얼 및 VGA 출력은 GPU 통합된

프로세서의 경우에만 지원됩니다 .

- Intel® Ivy Bridge CPU 에서 Intel® HD 그래픽 내장 비주얼 프 로그램 : Intel® Quick Sync Video 2.0, Intel® InTruTM 3D, Intel

Clear Video HD Technology, Intel® InsiderTM, Intel®

HD Graphics 2500/4000

- Intel® Sandy Bridge CPU 에서 Intel® HD 그래픽 내장 비주 얼 프로그램 : Intel® Quick Sync Video, Intel® InTruTM 3D, Intel® Clear Video HD Technology, Intel® HD Graphics 2000/3000, Intel

Advanced Vector Extensions (AVX)

- Intel® Ivy Bridge CPU 를 탑재한 DirectX 11, Pixel Shader 5.0. Intel® Sandy Bridge CPU 를 탑재한 DirectX 10.1, Pixel Shader 4.1

- Intel

Ivy Bridge CPU 에서 최대 공유 메모리 1760MB. Intel®

Sandy Bridge CPU 에서 최대 공유 메모리 1759MB.

- 더블 VGA 수출 : DVI-D 와 D-Sub 포트 독립 디스플레이 컨 트롤러를 지원

- 최대 해상도 1920x1200 @ 60Hz 까지 DVI 지원

- 최대 해상도 2048x1536 @ 75Hz 까지 D-Sub 지원

- DVI 포트를 이용한 HDCP 기능 지원

- DVI 포트를 이용한 1080p Blu-ray (BD) / HD-DVD 재생을 지

ASRock H61M-DG3/USB3 Motherboard

CoreTM i7 / i5 / i3 지원

한 국 어

Page 100

한 국 어

100

원 오디오 - 5.1 CH HD Audio (Realtek ALC662 Audio Codec) 랜 - PCIE x1 Gigabit LAN 10/100/1000 Mb/s

- Realtek RTL8111E

- 웨이크-온-랜 지원

- LAN 케이블 감지 지원

- 절전형 이더넷 802.3az 지원

- PXE 지원 후면판 I/O I/O Panel

- 1 개 PS/2 마우스 포트

- 1 개 PS/2 키보드 포트

- 1 개의 D-Sub 포트

- 1 개의 DVI-D 포트

- 4 개디폴트 USB 2.0 포트

- 2 개디폴트 USB 3.0 포트

- 1 개 LED(ACT/LINK LED 및 SPEED LED) 가 있는 RJ-45 LAN 포트

- 오디오 잭 : 라인 인 / 전방 스피커 / 마이크 USB 3.0 - Etron EJ188H 에 의한 후면 패널 USB 3.0 포트 2 개 , 최고 5Gb/s 의 USB 1.1/2.0/3.0 지원

- Etron EJ188H 에 의한 전면 패널 USB 3.0 헤더 1 개 (USB 3.0 포트 2 개 지원 ), 최고 5Gb/s 의 USB 1.1/2.0/3.0 지원 온보드 헤더 - 4 개 의 SATA2 3.0Gb/s 커넥터 , NCQ, AHCI 및“핫 플러그” 및 커넥터 기 능 지원

- 프린트 포트 헤더 1 개

- COM 포트 헤더 1 개

- 섀시 침입 헤더 1 개

- CPU 팬 커넥터 1 개 (4 핀 )

- 섀시 팬 커넥터 1 개 (4 핀 )

- 전원 팬 커넥터 1 개 (3 핀 )

- 24 핀 ATX 전원 헤더

- 4 핀 ATX 12V 파워 콘넥터

- 전면부 오디오 콘넥터

- USB 2.0 헤더 2 개 (4 개의 추가 USB 2.0 포트를 지원하는 헤더 2 개 )

- USB 3.0 헤더 1 개 (2 개의 추가 USB 3.0 포트를 지원하는헤더 2 개 ) BIOS - 32Mb AMI BIOS

- GUI 지원을 제공하는 AMI UEFI 적합형 BIOS

- “플러그 앤 플레이” 지원

- ACPI 1.1 웨이크 - 업 이벤트와의 호환

- 점퍼 프리 지원

ASRock H61M-DG3/USB3 Motherboard

ASRock H61M-DG3 User Manual [en, ru, de, es, fr, it]

Specifications and Main Features

Frequently Asked Questions

User Manual

English