ARISTON TVM 70C 6P (EX) 60HZ User Manual

Instruction booklet
Instruction booklet
TUMBLE DRYER
TUMBLE DRYER
Contents
GB
English, 1
PT
Português, 31
TVM 70
FR
Français, 11
AR
52, ،يبرع
NL
ES
Español, 21
NL
FA
Farsi, 64
Installation, 2
Warnings, 4
Care and Maintenance, 6
Description of the tumble dryer, 7
Control Panel, 7
Start and Programmes, 7
Laundry, 8
Service, 10
www.aristonchannel.com
This symbol reminds you to read this
instruction manual.
Keep this manual at hand for immediate reference whenever
necessary. Always store this manual close to the tumble dryer and
remember to pass it on to any new owners when selling or tran-
sferring the appliance, so they may familiarise with the warnings
and suggestions herein contained.
Read these instructions carefully: the following pages contain
important information on installation and useful suggestions for
operating the appliance.
1
Installation
m
B
A
GB
Where to install the tumble dryer
If the dryer is installed below a worktop, ensure there are 10 mm between the upper panel of the dryer and any objects above it, and 15 mm between the sides of the machine and the walls or furniture units adjacent to it. This en­sures adequate air cir­culation. Make sure the air inlets on the rear panel are not blocked or obstructed.
Ventilation
This appliance gently dries laundry by taking in cold, clean and relatively dry air, heating it and passing it through the fabric. To facilitate the drying process, damp air is expelled at the rear, through a ventilation hose. When the dryer is in use, there has to be adequate ventilation to avoid a back flow of gases into the room from appliances burning other fuels, including open fires.
Mobile ventilation system
When using the tumble dryer with the mobile ventilation system, a ventilation hose must be connected. The hose should be securely fastened to the ventilation hole at the rear of the appliance (see “Description of the tumble dryer”). We recommend the hose is connected to an outlet near the tumble dryer, if possible. If it cannot be installed in a permanent spot, the tumble dryer will still function perfectly well if the ventilation hose is passed through a partially­opened window. Make sure you do not point the ventilation hose towards the air inlet, which is located on the rear of the appliance. The ventilation hose should not exceed a maximum length of 2.4 metres; it should also be shaken frequently to remove any fluff, dust or water deposits inside it. Make sure you do not crush the hose.
Fixed ventilation system
We recommend the ventilation hose is connected to a ventilation system for windows or doors, available from the retailer which originally sold you the appliance or from your local spare parts stockist.
Wall ventilation hole
1. Leave an opening in the wall to the left of the tumble dryer installation site.
2. Make the hose as short and straight as possible, in order to prevent any moisture from condensing and leaking back into the appliance.
3. The hole in the wall must also be straight and pointing downwards, so that the flow of air coming out is not impeded. Areas A and B should be checked frequently, to prevent the accumulation of fluff or debris, particularly if the tumble dryer is used very often. The hose adaptor must be fitted correctly, in order to prevent damp air from coming back into the room.
Window ventilation hole
The ventilation hole should be directly behind the dryer in
order to keep the hose as short as possible. Make sure you do not push the tumble dryer too far backwards, as this could lead to the ventilation hose being crushed, bent or even disconnected. There should be no cuts, kinks or “U”-shaped bends in the hose, as these could impede
ventilation or trap condensation. The end of the hose must be facing downwards, in order to prevent the hot, damp air from forming condensation in the room or the tumble dryer. Make sure that the tumble dryer is adequately ventilated, and that the end of the ventilation hose is not pointing
towards the air inlet pipe on the rear of the appliance. The ventilation hose must always be fitted to ensure optimum performance. Make sure that the ventilation hose and the air inlet vents are not obstructed or blocked. Do not let the tumble dryer recirculate exhaust air. Improper use of the tumble
dryer may result in fire hazards.
Ventilation through an open window
The air emitted by the tumble dryer must not be expelled in the same duct as used for the fumes produced by different appliances which burn gas or other fuels. Do not discharge the exhaust air into an extraction system or any duct with an extractor fan. This will affect the way the
thermal controls operate and can result in a fire hazard.
Make sure that the room in which the tumble dryer is installed is not damp, and that it is adequately ventilated.
We do not recommend that the dryer is installed in a cupboard but the dryer must never be installed behind a lockable door, a sliding door or a door with a hinge on the opposite side to that of the dryer door.
The appliance must be installed with the
rear surface placed against a wall.
2
Electrical connections
Before plugging the appliance into the socket, check the following:
Make sure your hands are dry.
The socket must have an earth connection.
The socket must be able to withstand the machine’s maximum power output as indicated on the rating plate (see Description
of the tumble dryer).
GB
The power supply voltage must fall within the values indicated on the rating plate (see
Description of the tumble dryer).
Do not use extension leads. Do not pull the power supply cable. Do not use multiple plug adaptors if the appliance is fitted with a plug. For appliances with fitted plug, if the plug is not suitable for you socket outlet, contact a qualified technician.
The dryer must not be installed outdoors, even if the space is sheltered.
Once installed, the dryer’s electrical wire and plug must be within reach.
The power cord must not be bent or squashed.
Levelling the tumble dryer
The tumble dryer should be installed level in order to operate correctly.
After installing the tumble dryer in its permanent position, make sure it is level; check its side-to-side levelling first, followed by front-to-back.
If the tumble dryer is not perfectly level, use a wooden block to support it while you adjust the two front feet, up or down as necessary.
Before you start your dryer
Once the tumble dryer is installed, clean the inside of the drum before operating it and remove any dirt accumulated during transportation.
If the plug being replaced is a non­rewirable type, then the cut-off plug must be disposed of safely. DO NOT leave it where it can be inserted into a socket and create a shock hazard.
The electric cord must be regularly checked. If the supply cord is damaged, it must be replaced by service agent. (see
Service).
The manufacturer denies any responsibility should any of these rules not be followed.
If in doubt about any of the above consult a qualified electrician.
3
Warnings
!
This appliance has been designed and built according to international safety standards. These warnings are given for safety reasons and must be followed carefully.
General safety
•This appliance can be used by children
aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
• This tumble dryer has been designed for
home, and not professional, use.
• Do not touch the appliance while barefoot
or with wet hands or feet.
• Unplug the machine by pulling on the plug,
not the cord.
•Children should be supervised to ensure that they do not play with the dryer.
•Cleaning and user maintenance shall not be
made by children without supervision.
•Children of less than 3 years should be
kept away from the appliance unless continuously supervised.
• The appliance must be installed correctly
and have proper ventilation. The air intake vents behind the machine, the outlet vents and the vent tube should never be obstructed (see Installation).
• Never direct the vent tube outlet towards
the air intake at the back of the machine.
• Never allow the tumble dryer to recycle
exhaust air.
• Never use the dryer on carpeting where the
pile height would prevent air from entering the dryer from the base.
• Check to see if the dryer is empty before
loading it.
The back of the dryer could become very
hot. Never touch it while in use.
• Do not use the dryer unless the filter, is
securely in place (see Maintenance).
• Do not overload the dryer (see Laundry for
maximum loads).
• Do not load items that are dripping wet.
�Carefully check all instructions on clothing
labels (see Laundry).
• Do not tumble dry large, very bulky items.
• Do not tumble dry acrylic fibres at high
temperatures.
• Do not turn off the dryer when there are still
warm items inside.
• Clean the filter after each use (see Maintenance).
• Do not allow lint to collect around the dryer.
• Never climb on top of the dryer. It could result in damage.
• Always follow electrical standards and requirements (see Installation).
• Always buy original spare parts and accessories (see Service).
To minimise the risk of fire in your tumble dryer, the following should be observed:
• Tumble dry items only if they have been washed with detergent and water, rinsed and been through the spin cycle. It is a fire hazard to dry items that HAVE NOT been washed with water.
�Do not dry garments that have been treated with chemical products.
• Do not tumble dry items that have been spotted or soaked with vegetable or cooking oils, this constitutes a fire hazard. Oil-affected items can ignite spontaneously,especially when exposed to heat sources such as a tumble dryer. The items become warm, causing an oxidisation reaction with the oil, Oxidisation creates heat. If the heat cannot escape, items can become hot enough to catch fire. Piling, stacking or storing oil-effected items can
prevent heat from escaping and so create a fire hazard.If it is unavoidable that fabrics containing vegetable or cooking oil or those that have been contaminated with hair care products be placed in a tumble dryer they should first be washed with extra detergent
- this will reduce, but not eliminate the hazard. They should not be removed from the dryer and piled or stacked while hot.
• Do not tumble dry items that have previously been cleaned in or washed in, soaked in or soiled with petrol/gasoline, dry cleaning solvents or other flammable or explosive substances. Highly flammable substances commonly used in domestic environments including cooking oil, acetone, denatured alcohol, kerosene, spot removers, turpentine, waxes and wax removers. Ensure these items have been washed in hot water with an extra amount of detergent before being dried in the tumble dryer.
�Do not tumble dry items containing foam
Warnings
!
This appliance has been designed and built according to international safety standards. These warnings are given for safety reasons and must be followed carefully.
General safety
•This appliance can be used by children
aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand
the hazards involved.
• This tumble dryer has been designed for
home, and not professional, use.
• Do not touch the appliance while barefoot
or with wet hands or feet.
• Unplug the machine by pulling on the plug,
not the cord.
•Children should be supervised to ensure that they do not play with the dryer.
•Cleaning and user maintenance shall not be
made by children without supervision.
•Children of less than 3 years should be
kept away from the appliance unless continuously supervised.
• The appliance must be installed correctly
and have proper ventilation. The air intake vents behind the machine, the outlet vents and the vent tube should never be obstructed (see Installation).
• Never direct the vent tube outlet towards
the air intake at the back of the machine.
• Never allow the tumble dryer to recycle
exhaust air.
• Never use the dryer on carpeting where the
pile height would prevent air from entering the dryer from the base.
• Check to see if the dryer is empty before
loading it.
The back of the dryer could become very
hot. Never touch it while in use.
• Do not use the dryer unless the filter, is
securely in place (see Maintenance).
• Do not overload the dryer (see Laundry for
maximum loads).
• Do not load items that are dripping wet.
�Carefully check all instructions on clothing
labels (see Laundry).
• Do not tumble dry large, very bulky items.
• Do not tumble dry acrylic fibres at high
temperatures.
• Do not turn off the dryer when there are still
warm items inside.
• Clean the filter after each use (see Maintenance).
• Do not allow lint to collect around the dryer.
• Never climb on top of the dryer. It could result in damage.
• Always follow electrical standards and requirements (see Installation).
• Always buy original spare parts and accessories (see Service).
To minimise the risk of fire in your tumble dryer, the following should be observed:
• Tumble dry items only if they have been washed with detergent and water, rinsed and been through the spin cycle. It is a fire hazard to dry items that HAVE NOT been washed with water.
�Do not dry garments that have been treated with chemical products.
• Do not tumble dry items that have been spotted or soaked with vegetable or cooking oils, this constitutes a fire hazard. Oil-affected items can ignite spontaneously,especially when exposed to heat sources such as a tumble dryer. The items become warm, causing an oxidisation reaction with the oil, Oxidisation creates heat. If the heat cannot escape, items can become hot enough to catch fire. Piling, stacking or storing oil-effected items can prevent heat from escaping and so create a fire hazard.If it is unavoidable that fabrics containing vegetable or cooking oil or those that have been contaminated with hair care products be placed in a tumble dryer they should first be washed with extra detergent
- this will reduce, but not eliminate the hazard. They should not be removed from the dryer and piled or stacked while hot.
• Do not tumble dry items that have previously been cleaned in or washed in, soaked in or soiled with petrol/gasoline, dry cleaning solvents or other flammable or explosive substances. Highly flammable substances commonly used in domestic environments including cooking oil, acetone, denatured alcohol, kerosene, spot removers, turpentine, waxes and wax removers. Ensure these items have been washed in hot water with an extra amount of detergent before being dried in the tumble dryer.
�Do not tumble dry items containing foam
GB
4
rubber (also known as latex foam), or similarly textured rubber like materials. Foam rubber materials can, when heated, produce fire by spontaneous combustion.
�Fabric softener or similar products should not be used in a tumble dryer to eliminate the effects of static electricity unless the practice is specifically recommended by the manufacturer of the fabric softener product.
• Do not tumble dry undergarments that contain metal reinforcements eg. bras with metal reinforcing wires. Damage to the tumble dryer can result if the metal reinforcements come loose during drying.
�Do not tumble dry rubber, plastic articles such as shower caps or babies waterproof covers, polythene or paper.
• Do not tumble dry rubber backed articles, clothes fitted with foam rubber pads, pillows, galoshes and rubber coated tennis shoes.
• Remove all objects from pockets such as lighters and matches.
WARNING: Never stop the dryer before the end of the drying cycle unless all items are quickly removed and spread out so that the heat is dissipated.
Save energy and respect the environment
• Wring out all items to eliminate excess water before
tumble drying (if you use a washing machine first, select a high spin cycle). Doing this will save time and energy during drying.
• Always dry full loads - you save energy: single items or
small loads take longer to dry.
• Clean the filter after each use to contain energy
consumption costs (see Maintenance).
rubber (also known as latex foam), or
similarly textured rubber like materials. Foam rubber materials can, when heated, produce fire by spontaneous combustion.
�Fabric softener or similar products should not be used in a tumble dryer to eliminate the effects of static electricity unless the practice is specifically recommended by the manufacturer of the fabric softener product.
• Do not tumble dry undergarments that contain metal reinforcements eg. bras with metal reinforcing wires. Damage to the tumble dryer can result if the metal reinforcements come loose during drying.
�Do not tumble dry rubber, plastic articles such as shower caps or babies waterproof covers, polythene or paper.
• Do not tumble dry rubber backed articles, clothes fitted with foam rubber pads, pillows, galoshes and rubber coated tennis shoes.
• Remove all objects from pockets such as lighters and matches.
WARNING: Never stop the dryer before the end of the drying cycle unless all items are quickly removed and spread out so that the heat is dissipated.
Save energy and respect the environment
• Wring out all items to eliminate excess water before tumble drying (if you use a washing machine first, select a high spin cycle). Doing this will save time and energy during drying.
• Always dry full loads - you save energy: single items or small loads take longer to dry.
• Clean the filter after each use to contain energy consumption costs (see Maintenance).
Maximum load sizes: 7 kg
Power consumption
o-mode (Po) - Watts 0.00
left-on mode (Pl) - Watts NA
Programs Kg kWh Minutes
Standard cotton*
Standard cotton
Synthetics 3 1.15 35
* This is the reference program for the energy label and suitable to dry normal wet cotton laundry. This is the most ecient programme in terms of energy consumption for drying wet cotton laundry.
7 3.97 109
3.5 2.19 65
GB
5
Care and maintenance
GB
Disconnecting the power supply
! Disconnect the dryer when not in use or during cleaning and maintenance operations.
Cleaning the filter after each cycle
The filter is a fundamental component of the dryer: its function is to collect lint and fluff that form during drying.
Clean the filter once drying is completed, by rinsing it under running water or cleaning it with a vacuum cleaner. Should the filter become clog­ged, the flow of air inside the dryer will be seriously
hampered: drying times becomes longer and more energy is consu­med. Moreover, the dryer may become damaged. The filter is located in front of the dryer seal
(see Picture).
Removing the filter:
1. Pull the filter’s plastic handle upwards (see
Picture).
2. Clean the fluff off the filter and replace it correctly. Ensure that the filter is pushed fully home. ! Do not use the dryer unless the filter has been replaced in its holder.
Checking the drum after each cycle
Rotate the drum manually to remove smaller items (handker­chiefs) that could have been left inside the dryer.
Cleaning the drum
! Avoid using abrasives, steel wool or stainless steel cleaning
agents to clean the drum. A coloured film may appear on the stainless steel drum surface: it may be caused by a combina­tion of water and/or cleaning agents such as wash-softeners. This coloured film does not affect the dryer’s performance.
Emptying the water container after each cycle
Remove the water container and empty it into a sink or other suitable drain outlet, then replace it correctly. Always check the water contai­ner and empty it before starting a new drying cycle.
-Failure to empty the water container may cause the following:
- The dryer stops heating (thus the load may still be damp at the end of the drying cycle).
- The “Empty water container” LED activates to show that the water container is full.
Priming the Water Collection System
When your dryer is new, the Water Container will not collect Water until the system is primed, this will take 1 or 2 drying cycles. Once primed it will collect Water
during every cycle.
Cleaning the Heat Pump Filter Unit
• Periodically (every 5 drying cycles) remove Heat pump filter unit and clean any build up of fluff from the surface of the filter by rinsing it under running water or with your vacuum cleaner. We however recommend that you clean this filter after every drying cycle to optimize the dryers performance.
To remove Heat pump filter unit:
1. Unplug the dryer and open the door.
2. Remove the filter unit by rotating the 4 clips to the vertical position then pulling the filter unit towards you.
3. Separate the two parts of the filter unit and clean the surface of the filter. ! Warning: The front of
the heat pump is made from thin metal plates.
Take care that you do not damage these or cut yourself when cleaning, removing or replacing the filter unit.
6
4.Whenever you clean the Heat pump filter unit always clean any build up of fluff from the surface of the metal plates. Carefully clean this fluff off with a damp cloth,sponge or vacuum
cleaner. Never use your
Fingers.
5. Assemble the two parts of the filter clean the surface of the seals and replace with the 4 clips into the horizontal position, sure that the catches have been secured.
Cleaning the tumble dryer
The external metal, plastic and rubber parts can be clea- ned with a damp cloth.
Clean the front air intake grille regularly (every 6 months) with a vacuum cleaner to remove any lint, fluff or dust deposits. Furthermore, remove any lint deposits from the front part of the condenser and from the filter area, using a vacuum cleaner every so often.
! Do not use solvents or abrasives. ! Have the dryer checked regularly by authorised technical
personnel in order to ensure that the electrical and mechani- cal parts work safely (see Assistance).
Water container
Heat pump filter unit
Condenser cover
Catches
Filter
Handle
Air intake
Quick Tips !Remember to clean your filter and Heat Pump filter unit after each load. ! Remember to empty your water container after each load. ! Doing this will keep your machine working at its BEST!
Description of the tumble dryer
Front side Rear side
Control panel
Serial number
and model
Control panel
number
Drum
Filter
Rating Plate
Caution, high
temperature
HEAT
Button
TIMER
Knob
130
Indicator
0
120
110
80
100
Air inlet
20
30
40
50
60
70
Connection for
ventilation hose
START
Button
GB
The timer knob This is used to set the drying time: turn the knob in a clockwise direction until the indicator is set to the desired drying time (see Start and Programmes). Do not attempt to turn the knob anticlockwise.
The Heat button It can be used to customise the selected programme in accordance with your own requirements.
START button Press the button to begin drying.
Start and Programmes
Choosing a Programme
1. Plug the dryer into the electrical socket.
2. Sort your laundry according to fabric type (see Laundry).
3. Open the door and make sure the filter is clean and in place (see Care and maintenance).
4. Load the machine and make sure that the items are not in the way of the door seal. Close the door.
5. Choose the drying time by checking the Drying Guide table for the type of fabric you are drying (see Laundry).
- Set the temperature with the HEAT button..
- Select a drying time by rotating the TIMER knob clockwise.
6. Press the START button to begin.During the drying programme, you can check on your laundry and take out the items that are dry while the others continue drying. When you close the door again, press START in order to resume drying.
7. During the last few minutes of Drying Programmes before the programme is completed, the final COOL TUMBLE phase is entered (fabrics are cooled), this phase should always be allowed to complete.
8. Open the door, take the laundry out, clean the filter and replace it (see Care and maintenance).
9. Unplug the dryer.
7
Laundry
GB
Sorting laundry
Check the symbols on the care labels of the various
garments to verify whether the garments can be safely tumble dried.
• Sort laundry according to the type of fabric.
• Empty all pockets and check for loose buttons.
• Close zips and hooks and fasten belts and strings without tightening them.
• Wring out garments to remove the maximum amount of water possible.
!
Do not load the dryer when garments are dripping wet.
Maximum load sizes
Do not overload the drum. The following values indicate the weight of dry garments: Natural fibres: maximum kg Synthetic fibres: maximum kg
7
3
! Do not overload the dryer as this may result is reduced drying performance.
Care labels
Always check the care labels, especially when placing garments in the tumble dryer for the first time. Below are the most commonly used symbols:
May be tumble dried.
Do not tumble dry.
Drying times
Drying times are approximate and may vary depending on the following:
• Amount of water retained by items after the spin cycle: towels and delicate items retain a lot of water.
• Fabrics: items of the same fabric, but with different texture and thickness may have different drying times.
• Amount of laundry: single items and small loads may take longer to dry.
• Drying: if items are to be ironed, they can be removed from the dryer while still slightly damp. Items that require complete drying can be left longer.
• Heat setting.
• Temperature of the room: the lower the temperature of the room, the longer it will take for the dryer to dry clothing.
• Bulk: certain bulky items require special care during the drying process. We suggest removing these items and replacing them in the dryer once they have been shaken out: repeat this procedure several times during the course of the drying cycle.
! Do not over-dry items. All fabrics contain natural dampness which helps to keep them soft and fluffy.
Tumble dry – high heat.
Tumble dry – low heat.
Typical weights
Note: 1kg = 1000g; (1 lb = 16 oz.)
Clothes
Blouse
Dress
Jeans
10 Nappies
Shirt
T - Shirt
Cotton Other
Cotton Other
Cotton Other
150g (5 oz) 100g (3 oz)
500g (1lb 2 oz) 350g (12 oz)
700 g (1 lb 6 oz)
1000 g (2 lb 6 oz)
300g (10 oz) 200g (7 oz)
125 g (4 oz)
At the end of a drying cycle, cottons could still be damp if you grouped cottons and synthetics together. If this happens simply give them an additional short period of drying.
Household items
Duvet cover (Double)
Large Tablecloth
Small Tablecloth
Tea Towel
Bath Towel
Hand Towel
Double Sheet
Single Sheet
Cotton Other
1500g (3 lb 5 oz) 1000g (2 lb 3 oz)
700 g (1 lb 6 oz)
250 g (9 oz)
100 g (3 oz)
700 g (1 lb 6 oz)
350 g (12 oz)
500 g (1 lb 2 oz)
350 g (12 oz)
8
Drying times
The drying time depends on the size of the load and on the type of fabric it contains (see Table). The COOL TUMBLE cycle runs during the final 10 minutes of the programme. ! For large loads, select the High Heat option if available.
GB
Fabric
Cotton –
high heat
Synthetics –
higt heat
Acrylics –
low heat
1 kg 2 kg 3 kg 4 kg 5 kg 6 kg 7 kg
20 - 30
minutes
20 - 30
minutes
25 - 40
minutes
35 - 45
minutes
35 - 45
minutes
40 - 60
minutes
45 - 60
minutes
45 - 60
minutes
- - - -
Load
60 - 70
minutes
- - -
70 - 80
minutes
80 - 100
minutes
90 - 120
minutes
Troubleshooting
If you feel that the dryer is not working properly, consult the following troubleshooting suggestions before contacting the Technical Assistance Centre (see Service).
Problem:
The dryer does not start.
Drying times are too long.
Possible causes / Solutions:
• The plug has not been inserted far enough into the socket to make contact.
• There has been a power cut.
• The fuse has blown. Try connecting another appliance to the same socket.
• If an extension cord is used, try connecting the dryer plug directly into the socket.
• The TIMER knob has not been set properly (see Start and Programmes).
• The START button has not been pressed (see Start and Programmes).
• The START button was pressed with the door open. Make sure the door is closed before pressing the START button (see Start and Programmes).
! If the START button is pressed with the door open the dryer will not start. Close the
door, wait for a few seconds and then press the START button again (see Start and Programmes).
• The filter has not been cleaned (see Care and maintenance).
• The temperature setting is not ideal for the type of fabric you are drying (see Start and Programmes).
• The correct programme has not been selected for the load (see Start and Programmes).
• The flexible ventilation hose may be blocked (see Installation).
• The air inlet may be blocked or obstructed (see Installation).
• The fixed ventilation flap, on the protective weatherproof cover, may be obstructed
(see Installation).
• The items were too wet (see Laundry).
• The dryer is overloaded (see Laundry).
9
Service
GB
Before calling the Service Centre:
• Use the troubleshooting guide to see if you can solve the problem yourself (see Troubleshooting).
• If not, turn off the dryer and call the Service Centre closest to you.
What to tell the Service Centre:
• Name, address, and post code;
• telephone number;
• the type of problem;
• the date of purchase;
• the appliance model (Mod.);
• the dryer serial number (S/N). This information can be found on the data label inside the door of the machine.
Spare Parts
This dryer is a complex machine. Repairing it yourself or having a nonauthorised person try to repair it could cause harm to one or more persons and to the machine, and could invalidate the spare parts warranty. Call an authorised technician if you experience problems while using the machine.
Information on recycling and disposal
As part of our continual commitment towards environmental protection, we reserve the right to use recycled quality components to reduce costs for our customers and to minimise materials wastage.
• Disposing of the packaging materials: follow local regulations to allow for recycling of packaging materials.
• In order to minimise the risk of injury to children, remove the door and plug, then cut the power supply cord flush with the ap­pliance. Dispose of these parts separately to prevent the appliance from being connected to a power supply socket.
Disposal of old household appliances
European Directive 2012/19/EC concerning Waste Electrical and Electronic Equipment (WEEE) states that household
appliances should not be disposed of using the normal solid urban waste cycle. Exhausted appliances should be collected separately in order to optimise the cost of re-using and recycling materials comprising the machine, while preventing
potential damage to public health and the environment. The crossed-out wheeled bin symbol appears on all products to remind owners of the obligations regarding separate waste collection. Owners should contact their local authorities or appliance dealers for further information concerning the correct disposal of hou­sehold appliances.
This appliance has been designed, constructed and distributed in compliance with the requirements of European Directives:
- LVD 2014/35/EU, EMC 2014/30/EU and RoHS 2011/65/EU.
10
Loading...