Ariston AS100 User Manual
User Instruction Book
for
ARISTON
DISHWASHER
Model AS100
19502456300
Safety Is a Good Habit to Get Into
NOTICE
Carefully read the instructions contained in this manual, as
they provide important information which is essential to
safe and proper installation, use and maintenance of the
appliance.
This appliance complies with the following
EEC directives:
- 73/23/EEC of 19/02/73 (Low Voltage) and subsequent
modifications;
- 89/336/EEC of 03/05/89 (Electromagnetic
Compatibility) and subsequent modifications.
1.Carefully dispose of the packing material.
2.After removing the packing, check to make sure that the
appliance is not damaged. If in doubt, contact a qualified
professional.
3.The dishwasher must only be used by adults for the
washing of household dishes and cooking utensils.
4.Fundamental rules to follow when using the appliance:
- Never touch the dishwasher when barefoot or with wet
hands or feet;
- We discourage the use of extension cords and multiple
sockets;
- During installation, the power supply cord must not be
excessively or dangerously bent or flattened;
- If the appliance is not operating properly or maintenance
must be performed, disconnect the appliance from the
power supply.
5.Keep detergents out of the reach of children, who must
also be kept away from the dishwasher when it is open.
6.This appliance cannot be installed outdoors, not even if
the area in which it is installed is covered by a roof; it is also
very dangerous to leave it exposed to the rain and elements.
7.Do not touch the heating element during or after a wash
cycle.
8.Do not lean or sit on the door when it is open, as this
could overturn the dishwasher.
9.If the appliance malfunctions, turn off water supply to
the appliance and disconnect the plug from the wall socket.
Then, consult the section entitled, "T roubleshooting." If you
cannot resolve the problem, contact a service centre.
10.Appliances which are no longer being used must be
made inoperable by cutting the power supply cord and
removing the door lock.
To maintain the EFFICIENCY and SAFETY of this
appliance, we recommend:
l call only the Service Centers authorized
by the manufacturer
l always use original Spare Parts
Close-up View (control panel)
R
50
ON - OFF Button
ON - OFF Light
Handle For Opening Door
Knob For Selecting Cycles
EF
H
A
B
ON
OFF
65
C
D
55
55
50
"PLUS 65°C" Button
"RAPID 50°C" Button
Low Rinse Aid Indicator Light
1
GB
Close-up View (Interior)
G
J
E
F
H
K
I
Upper Rack
Top Sprayer Arm
Rack Height Adjustor
Lower Rack
Technical characteristics
L
Bottom Sprayer Arm
Salt Container Cap
Washing Filter
Detergent and Rinse Aid Dispenser
Width cm. 4 4,5
Depth cm. 60
Height cm. 85
Capacity 8 standard place settings
Mains water pressure 20 KPa÷ 1M Pa (0,2 ÷10 b ar)
Power voltage See data plate
Total absorber power See data plate
Fuse See data plate
GB
2
Salt ......
Salt
The hardness of the water varies from place to place. If
hard water is used in the dishwasher, deposits will form on
the dishes and utensils.
The appliance is equipped with a special softener that uses
a salt specifically designed to eliminate lime and minerals
from the water.
Loading the Salt into the Softener
Always use salt intended for use with dishwashers.
The salt container is located beneath the lower rack and
should be filled as follows:
1. Remove the lower rack and then unscrew and remove
the cap from the salt container;
2. If you are filling the container for the first time, fill it with
water;
3. Place the end of the funnel (supplied) into the hole and
introduce about 2 kg of salt. It is normal for a small amount
of water to come out of the salt container.
4. Carefully screw the cap back on.
Adjusting Salt Consumption
The dishwasher is designed to allow for adjusting the
amount of salt consumed based
on the harness of the water
used. This is intended to
optimize and customize the
level of salt consumption so that
it remains at a minimum.
Your Local Water Board can
supply the degree of hardness
of the water
in your area.
To adjust salt consumption,
proceed as follows:
1) Unscrew the cap from the salt container.
2) There is a ring on the container with an arrow on it (see
figure to the side), if necessary, rotate the ring in the
anticlockwise direction from the "_" setting towards the
"+" sign, based on the hardness of the water being used.
It is recommended that adjustments be made in accordance
with the following schema:
The salt container should be filled after about every 30 wash
cycles. To prevent the formation of rust, load the salt just
before beginning a wash cycle.
To prevent the formation of rust, load the salt just before
beginning a wash cycle.
Water Hardness
Salt
Clarke
degrees
0 ÷ 14 0 ÷ 17 0
14÷ 36 18 ÷ 44 1,8 ÷ 4,4
36 ÷ 71 45 ÷ 89 4,5 ÷ 8,9 MED 40 40
>71 > 89 > 8,9
°dH mmol/l
1,7 / 0 /
÷
Selector
position
-
+
consumption
(grams/cycle)
20 60
60 25
Autonomy
(cycles\2kg)
3
GB
Loading...