Arcam AVR100 User Manual

AVR100HANDBOOK

Arcam AVR100 surround sound receiver

Ampli-tuner audio-vidéo Arcam AVR100

Arcam AVR100 Surround-Sound-Empfängers

English

Français

Deutsch

Safety guidelines

Safety instructions

This product is designed and manufactured to meet strict quality and safety standards. However, you should be aware of the following installation and operation precautions:

1. Take heed of warnings and instructions

You should read all the safety and operating instructions before operating this appliance. Retain this handbook for future reference and adhere to all warnings in the handbook or on the appliance.

2. Water and moisture

The presence of electricity near water can be dangerous. Do not use the appliance near water – for example next to a bathtub, washbowl, kitchen sink, in a wet basement or near a swimming pool, etc.

3. Object or liquid entry

Take care that objects do not fall and liquids are not spilled into the enclosure through any openings. Liquid ﬁ lled objects such as vases should not be placed on the equipment.

4. Ventilation

Do not place the equipment on a bed, sofa, rug or similar soft surface, or in an enclosed bookcase or cabinet, since ventilation may be impeded. We recommend a minimum

distance of 50mm (2 inches) around the sides and top of the appliance to provide adequate ventilation.

5. Heat

Locate the appliance away from naked ﬂ ames or heat producing equipment such as radiators, stoves or other appliances (including other ampliﬁ ers) that produce heat.

6. Climate

The appliance has been designed for use in moderate climates.

7. Racks and stands

Only use a rack or stand that is recommended for use with audio equipment. If the equipment is on a portable rack it should be moved with great care, to avoid overturning the combination.

8. Cleaning

Unplug the unit from the mains supply before cleaning. The case should normally only require a wipe with a soft, damp,

lint-free cloth. Do not use paint thinners or other chemical solvents for cleaning.

We do not advise the use of furniture cleaning sprays or polishes as they can cause indelible white marks if the unit is subsequently wiped with a damp cloth.

9. Power sources

Only connect the appliance to a power supply of the type described in the operating instructions or as marked on the appliance.

10. Power-cord protection

Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords and plugs, and the point where they exit from the appliance.

11. Grounding

Ensure that the grounding means of the appliance is not defeated.

12. Power lines

Locate any outdoor antenna/aerial away from power lines.

13. Non-use periods

If the unit has a stand by function, a small amount of current will continue to ﬂ ow into the equipment in this mode. Unplug the power cord of the appliance from the outlet if left unused for a long period of time.

14. Abnormal smell

If an abnormal smell or smoke is detected from the appliance, turn the power off immediately and unplug the unit from the wall outlet. Contact your dealer immediately.

15. Servicing

You should not attempt to service the appliance beyond that described in this handbook. All other servicing should be referred to qualiﬁ ed service personnel.

16. Damage requiring service

The appliance should be serviced by qualiﬁ ed service personnel when:

A. the power-supply cord or the plug has been damaged, or B. objects have fallen, or liquid has spilled into the appliance,

or C. the appliance has been exposed to rain, or D. the appliance does not appear to operate normally or

exhibits a marked change in performance, or E. the appliance has been dropped or the enclosure

damaged.

Safety compliance

This product has been designed to meet the EN60065 international electrical safety standard.

AVR100

Using this handbook

This handbook has been designed to give you all the information you need to install, connect, set up and use the Arcam AVR100 surround sound receiver. The remote control handset supplied with the equipment is also described.

It may be that the AVR100 has been installed and set up as part of your system installation by a qualiﬁ ed Arcam dealer. In this case, you may wish to skip the sections of this handbook dealing with installation and setting up the unit. Use the Contents list (on this page) to guide you to the relevant sections.

Safety

Safety guidelines are set out on the inside front cover of this handbook.

Many of these items are common sense precautions, but for your own safety, and to ensure that you do not damage the unit, we strongly recommend that you read them.

Contents

Safety guidelines 2

Safety instructions 2 Safety compliance 2

Using this handbook 3

Safety 3

Installation 4

Positioning the unit 4 Setting up the aerials 4

Connecting inputs 5

AVR100 back panel connections 5 Interconnect cables 5

Connecting outputs 6

Connecting to other equipment 6

Connecting to a power supply 6 Setting up 7 Using the On Screen Display (OSD) 7

Setup page 7

Input settings page 7

Channel balance page 7

Channel delays page 8

Speaker settings page 9 Using the AVR100 10 Front panel controls 10

Input selection 10 Using the tuner 11

Tuning to a station 11

Storing a preset 11

Deleting an unused preset 11

RDS: Radio Data System 12

FM Mute/Mono 12 Using the remote control 13

CR-340 remote control 13 Reference 14 Bi-wiring and bi-amping loudspeakers 14

Before you start 14

Bi-wiring your loudspeakers 14

Bi-amping your system 14 Troubleshooting 15 Technical speciﬁ cations 16 Guarantee 17 On line registration 17

English

Manufactured under licence from Dolby Laboratories, Inc. ‘Dolby’, ‘AC3’, ‘Pro Logic’ and the double-D symbol are trademarks of

Manufactured under licence from Digital Theater Systems, Inc. US Patent Number 5,451,942 and other world-wide patents issued and

pending. ‘DTS’ and ‘DTS Digital Surround’, are trademarks of Digital Theater Systems, Inc.

AVR100

Installation

Installation starts with positioning the unit where it can operate effectively. To use the radio receiver, you will need to install an FM and/or an AM aerial.

Other input signals – from CD, MD, tape, DAT, VCR, DVD, games console or satellite receiver – will need to be connected to sockets on the AVR100’s back panel.

Output signals – TV, monitor, projector, preampliﬁ er, loudspeakers, headphones or other audio or digital outputs – also need to be connected to sockets on the back panel.

Positioning the unit

Place your AVR100 on a level, ﬁ rm surface. Avoid placing the unit in direct sunlight or near sources of heat

or damp. Ensure adequate ventilation. Do not place the unit in an

enclosed space such as a bookcase or cabinet as both of these will impede air ﬂ ow through the ventilation slots.

Setting up the aerials

FM aerial

An FM aerial is required to receive VHF radio signals. An external FM ribbon aerial is supplied as an accessory with the AVR100.

For optimal FM radio reception a roof or loft mounted aerial is advised. For your own safety it is recommended that a roof top aerial is ﬁ tted by an experienced contractor. Your Arcam dealer should be able to put you in contact with an aerial installer. A contractor will be able to tune your aerial to the nearest FM transmitter. In an apartment building an aerial system my already be installed. If this is the case you should have sockets in your home marked FM or VHF (do not use those marked TV).

The ‘T’ shaped wire aerial (dipole design) supplied should give reasonably good reception. Mount this aerial as high up as possible on a wall with the elements positioned horizontally. Try each usable wall of the room to see which gives best reception. Use tacks or adhesive tape to secure the aerial in a T shape. The tacks should not come into contact with the internal wire of the aerial.

Whether you decide to get an aerial professionally installed or opt to use the supplied aerial it should be connected to the FM Antenna input on the rear of the unit.

AM aerial

An AM aerial is required to receive AM/Medium Wave radio signals.

An external AM loop aerial is supplied as an accessory with the AVR100. This should be attached to the AM Antenna inputs with one end connected to AM and the other to Ground. It does not matter which way round this aerial is ﬁ tted. Rotate the aerial to discover which position gives the best reception.

In areas of weak reception or when the receiver is used inside a steel framed building (such as an apartment building) you can use a wire between 3 and 5 metres long to strengthen reception. Mount this high up outside the building, if possible, and connect one end of this wire to the AM antenna input as well as the loop aerial supplied. DO NOT DISCONNECT THE LOOP AERIAL.

The AM tuning ‘step size’ needs to be set according to your location. This is done using the switch on the rear panel: set it to 10kHz if you are in North America or 9kHz anywhere else.

AVR100

Connecting inputs

AC INLET

SURROUND

–

CENTREFRONT

–

OUT

VCR

DVD

SAT

AUX

OUT

(N.AM)10K

AM STEP

GROUND LIFT

SPEAKER

IMPEDANCE

SELECTOR

4–6Ω 8Ω

GROUND

120V 230V

LOUDSPEAKER

OUTPUTS

SUB

WOOFER

CENTER

AUDIO VIDEO S-VIDEO

S-VIDEO

VIDEO

AUDIO

PRE-OUT

TAPE 5.1 CH INPUT

SUB

WOOFER

CENTER

OUT

AUDIOR

(EU) 9K

LRLR

R L

GND

ANTENNA

MONITOR OUT

FRONT SURR FRONT SURR

DIGITAL

VCR DVD SAT

English

Interconnect cables

The use of high quality interconnect cables to and from your AVR100 is recommended to ensure the best sound and picture quality. Ask your Arcam dealer’s advice on cable selection.

This product does not feature a Phono input stage. If you wish to connect a turntable to your AVR100 you will need to use an in-line phono pre-amp. All line level inputs have the same sensitivity so may be used with any line level source equipment, even components other than those labelled. If you need to do so, your Arcam dealer can give you further advice on this.

CD input

Use audio interconnects to attach the left and right audio outputs from your CD player to the CD inputs on the AVR100.

TAPE loop

This input can be used to connect one of many different recording devices, for example, a tape deck, Mini-Disc or CD-R. Use audio interconnects to attach the left and right audio outputs from your recorder to the corresponding TAPE inputs on the AVR100.

To complete the record loop, attach the left and right outputs from the AVR100 to the corresponding record inputs on your recorder.

5.1 channel input

This multi-channel input takes up to six (i.e. ﬁ ve channels plus one sub-woofer) discrete channels of audio from a DVD audio player or a DVD player with an integrated decoder. Use audio interconnects to attach the DVD’s outputs to the appropriate 5.1

CH INPUT

For optimum performance from DVD video, however, it is usually better to use a digital connection to the AVR100’s own internal digital surround decoder instead.

SAT input

Use audio interconnects to attach the left and right audio outputs from your satellite or cable receiver (or digibox) to the corresponding

Using either the composite or the S-video output from your satellite receiver, connect it to the corresponding

S-VIDEO input on the AVR100.

If your satellite receiver provides a coaxial digital output, attach it via the

inputs on the AVR100.

SAT inputs on the AVR100.

SAT digital input.

VIDEO or

TAPE

DVD input

In most cases you will achieve the best audio performance from your DVD player by connecting its digital output to the

DVD digital input of the AVR100, using a suitable 75Ω digital

cable. Connect either the composite or S-video output from your DVD player to the corresponding VIDEO or S-VIDEO inputs on the AVR100.

If you are also using your DVD player to play CDs and prefer to use the stereo audio outputs, connect these to the

CD inputs

of the AVR100.

VCR loop

Use audio interconnects to attach the left and right audio outputs from your video cassette recorder to the VCR inputs on the AVR100. For the video signal, use either the composite or the S-video output from your VCR and attach to the corresponding input on the AVR100. If the VCR has a digital output, connect it to the VCR digital input on the AVR100.

To complete the record loop, attach the left and right outputs from the AVR100 to the corresponding record inputs on your VCR. Using the same type of video connection as for the input, connect the VCR picture output from the AVR100 to the corresponding input on your VCR.

AUX input and record loop

Use audio interconnects to attach the left and right audio outputs from your auxiliary source (another item of audio equipment or a games console) to the corresponding AUX inputs on the AVR100. If your source produces composite video output, connect this to the AUX composite video input.

If the auxiliary source is a recording device, complete the record loop by attaching the left and right

AUX outputs to the record

inputs on your recording device. With a video recorder, connect the composite video output (AUX) to the corresponding input on your recording device.

GROUND LIFT switch

If your system only takes audio sources from CD or DVD, set this switch to ‘GROUND’. In more complex setups which involve satellite inputs or radio aerials, grounding the unit may actually increase the level of background hum or buzz in the loudspeakers, in which case set the switch to ‘GROUND LIFT’.

VCR audio

AVR100

Connecting outputs

Connecting to other equipment

Monitor output

Both composite and S-video monitor outputs are provided for connection to the ‘Video line in’ of your TV, monitor, or projector. If you have both Composite and S-video inputs connected to your AVR100 you need only connect the S-VIDEO Monitor Output to your TV (provided that your TV accepts an S-video input).

Loudspeaker outputs

Before connecting loudspeakers to your AVR100 you must set the Impedance switch on the rear to the correct position.

WARNING: Never adjust this switch with the power on or you will damage the AVR100.

If your loudspeakers are rated at 6Ω or lower set the switch to the 4–6Ω position. If your loudspeakers are rated higher than 6Ω, set the switch to the 8Ω position.

WARNING: This unit should only be used with loudspeakers with an impedance rating between 4Ω and 8Ω.

The AVR100 is ﬁ tted with loudspeaker terminals in line with BFA (British Federation of Audio) standard speciﬁ cation. The terminal will accept spades, bare wire or a BFA plug. To connect spades or bare wires, unscrew the end of the terminal, insert the wire or spade and screw back up. Ensure that no stray strands of wire are allowed to touch other cables or the AVR100’s casing as this can cause a short circuit and damage the ampliﬁ er.

Connecting to a power supply

Wrong plug?

Check that the plug supplied with the unit ﬁ ts your supply and that your mains supply voltage agrees with the voltage setting (120V or 230V) indicated on the rear panel of the unit.

If your mains supply voltage or mains plug is different, consult your Arcam dealer or Arcam Customer Support on +44 (0)1223

203203.

Mains lead

The appliance is normally supplied with a moulded mains plug already ﬁ tted to the lead. If for any reason the plug needs to be removed, it must be disposed of immediately and securely, as it is a potential shock hazard when inserted into the mains socket. Should you require a new mains lead, contact your Arcam dealer.

Plugging in

Push the plug (IEC line socket) of the power cable supplied with the unit into the socket (AC INLET) in the back of the unit. Make sure it is pushed in ﬁ rmly.

Put the plug on the other end of the cable into your power supply socket and switch the socket on.

Non-use periods

If the unit is to be left unused for an extended period, we recommend that you switch the unit off from the front panel button, rather than use ‘stand by’ mode with the remote control.

Bi-wiring and Bi-amping loudspeakers

Notes on these techniques are given in the Reference section of this handbook.

Preampliﬁ er outputs

If you wish to upgrade your system by adding a power ampliﬁ er, always specify an Arcam unit to ensure matching gain.

The AVR100 has six line-level pre-amp outputs that can be connected to Arcam external power ampliﬁ ers to bi-amplify (‘bi-amp’) any of the channels. Alternatively, the AVR100 can be used solely as a preampliﬁ er.

Depending on how your system is conﬁ gured, the subwoofer

PRE-AMP OUT should be connected using a line level

interconnect, to either:

■ an active subwoofer, or

■ a power ampliﬁ er used to drive a passive subwoofer.

Headphone output

A 1/4” stereo jack socket is provided on the front panel for headphone listening. Inserting the jack socket automatically mutes the loudspeaker and pre-amp outputs from the AVR100.

AVR100

+ 11 hidden pages