Page 1
Quick reference guide
Software Rel. 1.1x
PREPARING SEEDING
User menu
Job Control:
Seed spacing alarm:
Working width:
Seeds weight (100):
Sensors efficiency:
Speed:
Load/save settings:
User Preferences:
Test:
New Job:
Resume Job:
BASIC USE OF KEYS
Shift cursor to
the next digit
Confirm entered
value
19.8
1
Reset displayed
value
Edit digit highlighted by cursor
Quit without confirming
Esc
value and/or go back to
previous menu
USE
s/m
1
5.8
3
2
Max
km/h
4
Esc
Minimum tolerance:
Maximum tolerance:
0 1 . 0 0
SEEDS PER METER SETTING
2
38
rpm
Display average seeding value for the machine
or the value for the selected row
Display current or top speed
Select the seed row
Activate sensor
reading
1
7.84
Row 1: Seeding tube clogged
4:36
ha
Deactivate sensor
reading
hh:mm
1
Maximum value:
Minimum value:
Seeds per meter
0 5 0 . 0
500.0
s/m
0.1
s/m
s/m
Activated row
When sensor is deactivated, the monitor does not
show data for the corresponding row.
Scroll values displayed next to pressed key
Deactivated row
Page 2
KEY TO ITEMS ON DISPLAY
Job: Job3
Rev. sensor 1 ! No rotation
Value of the set Rate: average value or value per row (when row number is shown on
the side, item 2).
Selected seed row: press F3 or F4.
Unit of measurement associated with the Rate.
Machine speed or top speed reached during current job (when Max. is shown on the
side, item 3a).
To change display mode, press F2:
Top speed displayed on the side;
Simulated speed displayed on the side.
Chart showing seeding rate deviation from setting:
Seed row number;
Seed spacing maximum tolerance;
Seed spacing deviation;
Seed spacing minimum tolerance;
Double fertilization enabled (sensor A and B);
Single fertilization enabled (sensor A);
x
Single fertilization enabled (sensor B).
x
Work data:
Seed spacing;
Population;
Rotation speed, rev counter 1;
Rotation speed, rev counter 2 (sensor number is shown on the side, item );
Productivity;
Work time;
Worked distance;
Seeds/meter.
Time.
Alarms.
Name of current job.
Work area.
Selected rev counter.
Page 3
OPERATION ALARMS
Rev. sensor 1 ! No rotation
Seed sensor XX! No signal
Rev. sensor X! No signal
Speed sensor! No signal
Position sensor! No signal
Shaft sensor XX! No signal
seeding exceeding max. limit
seeding below min. limit
Row XX: seeding exceeding max. limit
Row XX: seeding below min. limit
Row XX: Seeding tube clogged
Row XX: no seeding
Impeller X! Speed too high
Impeller X! Speed too low
SD card not available
SD card writing locked out
Impossible to save the file
Slow down! Maximum speed reached
- Alfa 310S is not receiving the signal from seed sensor on line XX
- Alfa 310S is not receiving the signal from rev. sensor X
- Alfa 310S is not receiving the signal from speed sensor
- Alfa 310S is not receiving the signal from seed state sensor
- Alfa 310S is not receiving the signal from shaft Rev. sensor XX
- Number of seeds per metre exceeds maximum set value
- Number of seeds per metre is below minimum set value
- Number of seeds per metre on seed row XX exceeds maximum set value
- Number of seeds per metre on seed row XX is below minimum set value
- Seeding tube is clogged or seed sensor for row XX has low efficiency
- Seeds are not detected on row XX
- Impeller X speed exceeds maximum set value
- Impeller X speed is below minimum set value
- Memory card is not inserted
- Memory card writing locked out
- No space available or damaged memory card
- Vehicle speed exceeds maximum set value
Row XX: no fertiliz. (A)
Row XX: no fertiliz. (B)
Row XX: Fertilizer tube clogged (A)
Row XX: Fertilizer tube clogged (B)
Shaft XX: No rotation
- Fertilizer A is not detected on row XX
- Fertilizer B is not detected on row XX
- Seeding tube is clogged or fertilizer sensor A for row XX has low efficiency
- Seeding tube is clogged or fertilizer sensor B for row XX has low efficiency
- No rotation of shaft XX is detected
via Palladio, 5/A - 42048 RUBIERA (RE) - Italy - tel. + 39 0522 622011 - Fax +39 0522 628944 - www.aragnet.com Cod. D20250_GB-m01
Loading...