APC SUA5000RMT5U, SUA0317 User Manual

4 grounding screws

2 wire nuts

Package Contents

Model 5000RM5U 208/230 V

Terminal block

Terminal block label

Screws for securing terminal block to UPS

Model 2200/3000 Tower 100/120/230 V

Input and output panels

Blank panel to cover terminal block

Model 2200/3000XL 120/208/230 V

Input panel

Output panel

Blank panel to cover terminal block

Input and output panels

Blank panel to cover terminal block

8 screws for securing

panels to UPS

Installation Guide Smart-UPS I/O Hardwire Kit

be disconnected.

models may have external batteries connected to the UPS. The external batteries must be

disconnected from the UPS.

NOTE: Model 5000RM5U has four internal batteries. The two front batteries must be

disconnected.

1. Disconnect equipment connected to the UPS.

Safety Information - read these instructions before hardwiring the UPS

Wiring must be performed by qualified electrical personnel.

Adhere to all national and local electrical codes when wiring this unit.

2. Press the OFF button located on the front of the UPS.

a. Model 5000RM5U has four internal battery modules. The two front internal batteries must

b. Models 2200/3000XL require the disconnect of one internal battery module. The XL

3. Disconnect batteries from the UPS.

c. All other units require the disconnect of one internal battery module.

4. Disconnect the UPS from utility power.

When removing the panels from the UPS, note which cable is connected to the AC

input. There are two 4-pin connectors on the UPS and they are not interchangeable.

Connect to localized APC Web sites for specific countries, each of which provides

customer support information.

Global support searching APC Knowledge Base and using e-support.

customer support requests.

– www.apc.com (Corporate Headquarters)

• Refer to the APC Web site to access documents in the APC Knowledge Base and to submit

APC Worldwide Customer Support

Customer support for this or any other APC product is available at no charge in any of the following

ways:

– www.apc.com/support/

Local, country-specific centers: go to www.apc.com/support/contact for information.

• Contact an APC Customer Support center by telephone or e-mail.

990-3239A 7/2008

Contact the APC representative or other distributor from whom you purchased your APC product

for information on how to obtain local customer support.

Reproduction in whole or in part without permission is prohibited.

APC, the APC logo, and Smart-UPS are trademarks of American Power Conversion Corporation.

All other trademarks, product names, and corporate names are the property of their respective owners and are used for informational purposes only.

Secure the terminal block and label to the

UPS as shown in the diagram, using

two screws (supplied).

Input panel

Secure the blank panel to the UPS using

three screws (supplied).

C Input

Connectors

Secure the hardwire input and output panels

(supplied), to the UPS using four of the screws

removed from the PDU/IO panels.

Install appropriate strain relief clamps

(not supplied), to the I/O panels as shown in

the diagram.

NOTE: The input and output cables may be

connected to the terminal block prior to

installing the panels and the terminal block

in the UPS.

Output panel

AC Input

Connector

Connect the terminal block and UPS connectors as shown in diagram.

Primary

Ground

(Green Wire)

Input Line1

Ground

Input Line2

(Hot)

(or Neutral)

C Input Connector

Installation Guide Smart-UPS I/O Hardwire Kit

Remove the five screws that secure the PDU/IO panels

to the UPS.

Save these screws for securing the I/O hardwire panels.

Disconnect the PDU/IO cables as shown in the diagram.

Output Line2

(or Neutral)

Output Line1

990-3239A 07/2008

Connect input and output wires as shown in diagram.

2200/3000 Tower 100/120/230 V models

The AC input/output panels on the 2200/3000 VA tower units vary in appearance. The hardwire panels and hardwiring configurations for the 2200/3000 VA tower units are identical.

+ 2 hidden pages