Page 1
®
HI-Q active loop antenna
LA390
Instruction Manual
AOR,LTD.
Authority on Radio Communications
Page 2
2
The LA390 is a compact active (30.5cm diameter) loop antenna specifically designed to
provide good reception when away from the main monitoring location or when large
external antennas are not practical. Compact, but achieving high performance, featuring
an internal high-gain amplifier.
LA390 vs. LA380
With similar performances, the LA390 offers in addition preselection for L.W and M.W bands, but not for the
specific 40kHz and 60kHz time signals. Preselection sharpness has also been improved.
Directivity
A rotating loop antenna is very directional. Depending on the loop’s orientation, you can peak an incoming
signal depending on its direction, or decrease an interfering signal.
For example the nulling feature will allow you to remove a station on a frequency and pick up another
(transmitting from a different direction) on the same frequency. Of course the directional characteristics
when listening to distant sky-wave signals will not be as pronounced as local ground-wave propagation.
Thanks to its directivity, it is also ideal for minimizing the effects of unwanted interfering local terrestrial
signals and noise.
The loop element features a 5 position band switch and a High-Q poly-variable capacitor (only active for
switch positions 1 to 4) to tune and peak the wanted frequency, while achieving maximum rejection of
unwanted out of band signals. This provides valuable additional selectivity for your receiver’s front-end
stages.
Using the LA390 active loop antenna
1) Connect the power supply to the rear panel
DC input socket, the LA390 requires 12V DC
at 80mA (9-15V DC). A 9V regulator is built
into the LA390 control unit.
To minimize noise, keep the power supply as
far away from the LA390 as practical. To
minimize electrical interference from the
power supply, for the reception of L.W and
M.W bands, you may wish to consider use of
a (non supplied) low noise regulated power
supply.
Page 3
3
2) Connect the supplied BNC-BNC coaxial lead between the LA390 and your receiver’s antenna input. If
your receiver is fitted with a connector other than BNC, an appropriate adaptor must be used.
3) Insert the receiving loop element into the top panel BNC socket of the LA390 cabinet.
4) Push the red front panel power switch, the green LED will illuminate to confirm that power is connected to
the control unit.
5) Switch on the receiver and tune to the desired frequency. Select the correct frequency range with the
band switch on the loop element. There are 5 positions to choose from:
Switch position
1
2
3
4
5
6) Rotate the tuning dial on the loop element (clockwise and anticlockwise) until the receiver signal strength
meter (S-meter) deflects to maximum and the incoming signal sounds clearest. If your receiver does not
have an S-meter, simply adjust for maximum received signal. Rotate the loop element until the signal is
strongest and any interfering signal is nulled.
(Position 5 is non-tunable, as the loop is wired to act as an amplified whip)
It is advisable to locate the LA390 close to a window in
order to achieve the best possible reception.
Frequencies Comments
150-800kHz Longwave (148.5-283.5kHz)
700kHz-3MHz Mediumwave (520kHz-1710kHz)
3-10MHz Shortwave bands 100 to 30 Meters
10-30MHz Shortwave bands 30 to 7.5 Meters
Others Between 10kHz and 500MHz, antenna acts as an amplified whip.
In case your listening station is too far way from a
window, you have the possibility to use a (non-supplied)
BNC-BNC coaxial patch lead between the control box
and the loop. A gender change is required at one end of
the cable, please use a BNC-BNC in-line socket.
The lead shouldn’t be longer than 5m.
Page 4
4
LA390 Specifications:
Frequency range
Impedance
Typical gain 150kHz: 23dB
Connector
Loop element size 305(W)x365(H)x60(D)mm
Control box size 120(W)x55(H)x85(D)mm
Weight
Cable
Power
Supplied acc.
10kHz-500MHz, 5 bands selectable
50 Ohm
25MHz: 20dB
50MHz: 20dB
30MHz: 20dB
250MHz: 17dB
500MHz: 10dB
BNC
Loop: 250g, control box: 230g
1m RG58A/U (BNC plugs)
External DC 12V (9-15V), approx. 80mA.
DC connector 1.3mm centre positive
LA390 Control box with loop
AC power supply
BNC-BNC Coaxial patch lead (1m)
Specifications subject to change without notice or obligation.
Precautions
The LA390 is NOT intended for transmit purposes.
Keep it away from excessive humidity and rain. LA390 is NOT waterproof.
We are not responsible for any damages to the antenna or your radio equipment due to improper use.
E&OE AOR LTD, 2008
AOR, LTD.
2-6-4, Misuji, Taito-Ku
Tokyo, 111-0055, Japan
http://www.aorja.com
mail@aorja.com
Copyright © 2008 All rights reserved
Loading...