Antari z3000 User Manual

User Manual

Antari Z Series Fog Machine

Congratulations on the purchase of your new

ANTARI Z Series FOG MACHINE.

Introduction

Thank you for choosing an ANTARI Fog Machine. You now own a rugged and powerful tate-of-the-art
machine. Prior to use, we suggest that you carefully read all of the instructions. By following the
suggestions found in this user manual, you can look forward to the reliable and satisfactory performance of
your ANTARI Fog Machine for years to come.

Please follow these operation, safety and maintenance instructions to ensure a long

and safe life for your fog machine.

Cautions
Risk of electric shock. Disconnect the appliance from the electric supply before

removing the cover. Note: there are no user serviceable parts inside.

Danger of electric shock

♦ Keep this device dry.
♦ For inside use only. Not designed for outside use.
♦ For the 110V models, use 3-prong grounded electrical outlet only. Prior to use take care

to determine that the unit is installed at the rated voltage.

♦ Always unplug your ANTARI Fog Machine before filling its tank.
♦ Keep fog machine upright.
♦ Turn off or unplug when not in use.
♦ This machine is not water- or splash-proof. If moisture, water, or fog liquid gets inside the

housing, immediately unplug the unit and contact a service technician or your ANTARI
dealer before using it again.

♦ No user serviceable parts inside. Refer to your ANTARI dealer or other qualified service

personnel.

Danger of burns

♦ For adult use only. Fog machine must be installed out of the reach of children. Never

leave the unit running unattended.

♦ Never aim the output nozzle directly at people.

1

♦ Fog machine output is very hot. Avoid coming within 60 cm of the output nozzle during

operation.

♦ Locate the fog machine in a well-ventilated area. Never cover the unit’s vents. In order to

guarantee adequate ventilation, allow a free air space of at least 20 cm around the sides
and top of the unit.

♦ Never aim the output nozzle at open flames.
♦ If the supply cord is damaged, it must be replaced by manufacturer or its service agent or

similarly qualified person in order to avoid a hazard.

♦ The output nozzle becomes very hot during operation (300°C). Keep flammable materials

at least 50 cm away from the nozzle.

♦ Always allow your ANTARI Fog Machine to cool down before attempting to clean or

service it.

Danger of explosion

♦ Never add flammable liquids of any kind (oil, gas, perfume) to the fog liquid.

Pay attention to all warning labels and instructions printed on the exterior of your ANTARI Fog

Machine

♦ Use only the high-quality, water-based fog liquid that your dealer recommends. Other fog

liquids may cause clogging or “spitting”.

♦ Always make sure there is sufficient liquid in the fog liquid tank. Operating this unit

without liquid will cause damage to the pump as well as over-heating of the heater.

♦ If your ANTARI Fog Machine fails to work properly, discontinue use immediately. Drain all

fog liquid from the tank, pack the unit securely (preferably in the original packing material),
and return it to your ANTARI dealer for service.

♦ Always drain tank before mailing or transporting this unit.
♦ Never drink fog liquid. If it is ingested, call a doctor immediately. If fog liquid comes in

contact with skin or eyes, rinse thoroughly with water.

Unpacking & Inspection

Open the shipping carton and verify that all equipment necessary to operate the system has
arrived intact. Refer to the “Features” section for information on what items are included with
your model. If any equipment is missing contact your ANTARI dealer immediately.

Before beginning initial setup of your ANTARI Fog Machine, make sure that there is no
evident damage caused by transportation. In the event that the unit’s housing or cable is
damaged, do not plug it in and do not attempt to use it until after contacting your ANTARI
dealer for assistance.

Setup
♦ Remove all packing materials from shipping box. Check that all foam and plastic padding

is removed, especially in the nozzle area.

♦ Place fog machine on a flat surface and remove fog liquid tank cap.
♦ Fill with ANTARI Fog Liquid or other high-quality water-based fog fluid. Any other types of

fluid can damage the unit. When filled, place cap back on liquid tank.

♦ Firmly attach the remote control cable to the proper input on the rear of the machine.

2