Antari Z-1000II, Z-800II User Manual [de]
ZII-SERIES USER MANUAL
Z-800II, Z-1000II & Z-1020 USER MANUAL
Z-800II, Z-1000II und Z-1020 BEDIENUNGSANLEITUNG
MODE D’EMPLOI des Z-800II, Z-1000II et Z-1020
Z-800II、Z-1000II、Z-1020 煙霧機使用手冊
Congratulations on the purchase of your new
ANTARI Z-SERIES II FOG MACHINE.
Wir beglückwünschen Sie zum Kauf Ihres neuen ANTARI Z-SERIES NEBELGERÄTES.
Nous vous félicitons pour l’achat de votre nouvelle
Z-SERIES machine à fumée d’ANTARI.
歡迎您成為 Antari 新 Z 系列煙霧機愛用者
♦ Read and save these instructions
Bitte lesen Sie diese Anweisungen und bewahren Sie sie gut auf
Lisez et Gardez ces instructions
請妥善保存此說明書
2012 Antari Lighting and Effects Ltd.
User Manual
Z-800II & 1000II & Z-1020 Fog Machine
Congratulations on the purchase of your new
ANTARI Z-Series II FOG MACHINE.
Introduction
Thank you for choosing a ANTARI Z-Series II Fog Machine. You now own a rugged and powerful state-of-theart machine. Prior to use, we suggest that you carefully read all of the instructions. By following the suggestions
found in this user manual, you can look forward to the reliable and satisfactory performance of your ANTARI
Fog Machine for years to come.
Please follow these operation, safety and maintenance instructions to ensure a long and safe life for your fog
machine.
CAUTION:
Risk of electric shock. Disconnect the appliance from the electric supply before refilling liquid, cleaning or
performing maintenance on the machine.
Danger of Electric Shock
♦ Don’t immerse in water. Keep this device dry.
♦ Household Use only. Not designed for outdoor use.
♦ For all models, use 3-prong grounded electrical outlet only. Prior to use take care to determine that the unit
is installed at the rated voltage.
♦ Always unplug your ANTARI Z-Series II Fog Machine before filling its tank.
♦ Always keep fog machine in upright position.
♦ Turn off or unplug the machine when not in use.
♦ This machine is not water-proof. Don’t immerse in water .If moisture, water, or fog fluid gets inside the
housing, immediately unplug the unit and contact a service technician or your ANTARI dealer before using it
again.
♦ No user serviceable parts inside. Refer to your ANTARI dealer or other qualified service personnel.
Danger of Burns
♦ This device is for adult use only and must be installed out of the reach of children. Never leave the unit
running unattended.
♦ Never aim the output nozzle directly at people.
♦ Fog machine output is very hot. Avoid coming within 60 cm of the output nozzle during operation.
♦ Locate the fog machine in a well-ventilated area. Never cover the unit’s vents. In order to guarantee
adequate ventilation, allow a free air space of at least 20 cm around the sides and top of the unit.
♦ Never aim the output nozzle at open flames.
♦ If the supply cord is damaged, it must be replaced by manufacturer or its service agent or similarly qualified
personnel in order to avoid a hazard.
♦ Not for space heating purpose.
♦ The output nozzle becomes very hot during operation (200°C). Keep flammable materials at least 50 cm
away from the nozzle.
♦ Always allow your ANTARI Fog Machine to cool down before attempting to clean or service it.
Danger of Explosion
♦ Never add flammable liquids of any kind (such as oil, gas, perfume) to the fog liquid.
♦ Use only high-quality, water-based fog liquid that your dealer recommends. Other fog liquids may cause
clogging or “spitting”.
♦ Always make sure there is sufficient liquid in the tank. Operating this unit without liquid will cause damage to
the pump as well as over-heating of the heater.
♦ If your ANTARI Z-800II, Z-1000II and Z-1020 Fog Machine fails to work properly, discontinue use
immediately. Drain all fog liquid from the tank, pack the unit securely (preferably in the original packing
material), and return it to your ANTARI dealer for service.
♦ Always drain tank before mailing or transporting this unit.
♦ Never drink fog liquid. If it is ingested, call a doctor immediately. If fog liquid comes in contact with skin or
eyes, rinse thoroughly with water.
Note: Pay attention to all warning labels and instructions printed on the exterior of your ANTARI Fog Machine
Unpacking & Inspection
Open the shipping carton and verify that all equipment necessary to operate the system has arrived intact.
The shipping carton should contain the following items:
1. One unit of Z-Series II Fog Machine
2. Power cord
3. Z-10 Remote Control
4. User Manual
5. Mounting brackets with washers/screws (for Z-1000II)
If any equipment is missing contact your ANTARI dealer immediately.
Before beginning your initial setup on ANTARI Z-800II, Z-1000II or Z-1020 Fog Machine, make sure that there is
no evident damage caused by transportation. In the event that the unit’s housing or cable is damaged, do not
plug it in and do not attempt to use it until after contacting your ANTARI dealer for assistance.
Setup
♦ Remove all packing materials from shipping box. Check that all foam and plastic padding is removed,
especially in the nozzle area.
♦ Place fog machine on a flat surface and remove fog liquid tank cap.
♦ Fill with high-quality, water-based fog liquid recommended by ANTARI dealer. Any other types of fluid can
damage the unit resulting in spitting and serious clogging problem. When filled, place cap back on liquid
tank. Be careful not to exceed the maximum fluid level. DO NOT OVERFILL.
♦ Firmly attach the remote control cable to the proper input on the back of the machine.
Operation
♦ Add fluid carefully to the liquid tank. Do not overfill the tank.
♦ Plug power cord into a grounded electrical outlet. Turn the power switch to “ON” on the back of the machine.
The unit will take a couple of minutes to warm up the heater. During this time the machine cannot generate
fog. When the remote control is attached the red lights (on Z-800II handle) and green light (on the remote)
will flash and stay ON when the warm-up time is complete.
♦ To emit fog press the button on the remote (if it is connected) and on the handle (for Z-800II) for the desired
length of time.
♦ For further information on operating your ANTARI Z-800II, Z-1000II and Z-1020 Fog Machine, see the
section titled “Remote Control Operation”.
Important: Always monitor tank fluid level as you are fogging. Running a fog machine with no fluid can
permanently damage the unit.
Z-1000II: Your model includes a mounting bracket designed for overhead installation; it may be
installed at floor level or suspended overhead. If the unit is to be mounted using the bracket, it is
important that the fog does not shoot directly at any one’s face. Whatever installation method
you choose, do not allow the unit to have more than a 25 degree angle of inclination.
Z-1000II Description
Note: A fluid level sensor is installed on the unit. The machine will stop to fog if the fluid is lower than usable
level.
If you experience low output, pump noise or no output at all, unplug immediately. Check fluid level, the
external fuse, remote control connection and power from the wall. If all of the above appears to be O.K.,
plug the unit again. If fog does not come out after holding the remote button down for 30 seconds, check
the hose attached to the tank to make sure there is fluid going through the hose. If you are unable to
determine the cause of the problem, do not simply continue pushing the remote button, as this may
damage the unit. Return the machine to your ANTARI dealer.
Technical Specifications
Model
Z-800II
Z-1000II
Z-1020
Power Supply
AC100-120V, AC 220-240V / 50HZ - 60HZ
Power Consumption
800 W
1,000 W
1,000 W
Output Volume
85 m³/min.
284 m³/min.
284 m³/min.
Tank Capacity
0.8 liters
1.7 liters
2.4 liters
Fluid Consumption
60 min./ 0.8 liter
18 min./ liter
11 min./ liter
Weight
3.5 kg
6.6 kg
9.8 kg
Dimensions (LxWxH)
315 x 128 x 165.5 mm
433 x 198 x 151 mm
370 x 295 x 135 mm
Remote Included
Z-10
Z-10
Z-10
Optional Remote
Z-40, Z-50
Z-40, Z-50
Z-40, Z-50
Warm-up Time
1.7 min.
5.5 min.
11 min.
Remote Control Operation
♦ Z-10: 10 meter wired remote controller with 6,3 mm jack plug of ANTARI Fog Machine models Z-800II, Z-
1000II and Z-1020. The red lamp indicates that the unit is receiving power. When the fog machine has
reached operating temperature the green light on this remote control will light up, indicating that the operator
may begin fog emission by pressing the red button. The green light flashes during fog machine warm-up
and re-heating cycles (approx. 1-2 minutes), and stays ON when the machine becomes operational. The Z10 features the “toggle switch’’ function: press once for continuous “ON”, press again to release continuous
“ON” function
♦ Z-40: 10 meter wired remote controller with 6,3 mm jack plug for ANTARI Fog Machine models Z-800II, Z-
1000II and Z-1020. Its two knobs allow the operator to customize fog machine functions by adjusting output
duration and interval. Press the yellow TIMER-button to activate the timer function. Adjust the interval
between each fog emission (within the range of 10 second to 250 seconds) by means of the INTERVAL
control knob. Adjust the duration of each fog emission (within the range of 10 to 120 seconds) by means of
the DURATION control knob. When pressed, the green FOG button overrides all other control functions and
activates maximum output. Press the red POWER ON/OFF button for continuous output.
♦ Z-50: Wireless remote controller with 6,3 mm jack plug for ANTARI Fog Machine models Z-800II, Z-1000II
and Z-1020. A remote operation is possible up to a distance of 50 meters. Keep the red button pressed for
fogging.
Z-10, Z-40, Z-50 Remote Controller
Performance Note
♦ All fog machines develop condensation around the output nozzle. Because this may result in some moisture
accumulation on the surface below the output nozzle, consider this condensation when installing your unit.
♦ All fog machines may sputter small amounts of fog occasionally during operation and for a minute or so
after being turned off.
♦ All fog machines have a recycling period after long bursts when the machine will shut itself down for a short
period in order to heat up again. During this time no fog can be produced.
Maintenance
Do not allow the fog liquid to become contaminated. Always replace the caps on the fog liquid container and the
fog machine liquid tank immediately after filling. After every 40 hours of continuous operation, it is
recommended to run a cleaning solution composed of 80% distilled water and 20% ACETIC ACID through the
system to prevent the accumulation of particulate matter in the heating element.
The recommended cleaning regimen is as follows:
1. Empty all fog liquid from the machine. Add cleaning solution to tank. Plug unit in and begin warm up.
2. Run the unit in a well-ventilated area until the tank is almost empty. Do not allow the pump to run dry.
3. Cleaning is now complete. Refill with fog liquid. Run the machine briefly to clear any cleaning solution from
the pump and heater.
4. Do not operate the fog machine without liquid at any time.
Note: All fog machines are prone to clogging due to the thick consistency of fog liquid and the high
temperature at which it vaporizes. However, a properly maintained fog machine should provide years of
reliable use.
Clean with a dry cloth only. Store dry.
Cleaning your fog machine regularly will help reduce costly replacement and repair charges.
Storage
1. When storing run distilled water (not tap water) through the system as described in the cleaning
regimen above. This will help avoid any particles condensing inside the pump or heater.
2. It is strongly recommended to test-run the machine on a monthly basis in order to achieve its best fogging
condition. A test-run consists of warming up the machine followed by a few minutes of emission. After that,
follow Step 1 under Storage.
Please read and save these instructions.
Antari Z-1000II & Z-1020 on-board DMX Fog Machine Settings
DMX Setting for Z-1000II and Z-1020 fog machines with on board DMX
Channel A
0 - 128 = OFF
129 – 255 = Maximum Volume Output (100%)
The Z-1000II and Z-1020 Fog Machine have on-board DMX control except on Z-800II. These two models
use 1 channel to control on/off operation. Each channel has a value range of 0 to 255. On/Off function can
be programmed using the DMX controller or the DMX control software being
used by lighting and effects operator.
If Channel A has a value from 0 to 128, the unit is OFF.
Between the values 129 to 255 the volume of fog output is is at maximum.
Note: In the example above, if the machine were assigned the DMX address of 130, Channel A would
correspond to DMX address 130.
In general, Antari fog machines with onboard DMX conform to the following performance specifications:
1. Average Operating temperature = 250ºC
2. Fogger can maintain maximum output for 30 seconds or more
Addressing
Each device occupies 1 channel. To ensure that the control signals are properly directed to each device, they
require adressing. This is to be adjusted for every single device by changing the DIP-switches as set out in the
table below.
The starting address is defined as the first channel from which the device will respond to the controller.
Please make sure that you do not have any overlapping channels in order to control each device correctly and
independently from any other fixture on the DMX data link. If two, three or more devices are addressed similarly,
they will work similarly.
Occupation of the DIP-switches:
Bedienungsanleitung
Antari Z 800II, Z-1000II & Z-1020 Nebelgerät
Wir beglückwünschen Sie zum Kauf Ihres neuen
ANTARI Z II NEBELGERÄTES.
Einleitung
Vielen Dank, dass Sie sich für ein ANTARI Z Nebelgerät entschieden haben. Sie sind nun
Im Besitz eines robusten und leistungsstarken Nebelgerätes. Vor Benutzung des Gerätes
bitte unbedingt diese Bedienungsanleitung sorgfältig lesen. Wenn Sie die Hinweise in
dieser Bedienungsanleitung beachten, können Sie sich in den nächsten Jahren auf eine
zuverlässige und überzeugende Leistung Ihres ANTARI Nebelgerätes freuen.
Bitte beachten Sie die folgenden Hinweise im Bezug auf Bedienung, Sicherheit und
Wartung, um eine lange Lebensdauer und einen sicheren Betrieb Ihres Nebelgerätes
sicherzustellen.
ACHTUNG:
Gefahr des elektrischen Schlages. Trennen Sie das Gerät vom Netz, bevor Sie die Abdeckung entfernen.
Gefahr eines elektrischen Schlages
♦ Vor Nässe schützen.
♦ Nur innerhalb geschlossener Räume betreiben. Nicht für den Betrieb im Freien geeignet.
♦ Für die 110V Modelle verwenden Sie bitte ausschließlich 3-adrige, geerdete Steckdosen. Vor
Inbetriebnahme darauf achten, dass das Gerät an die richtige Spannung angeschlossen wird.
♦ Vor Befüllen des Tankes ist Ihr ANTARI Z Nebelgerät immer vom Netz zu trennen.
♦ Achten Sie darauf, dass das Nebelgerät stets aufrecht installiert ist.
♦ Wird das Gerät außer Betrieb genommen, ist das Gerät auszuschalten oder vom Netz zu trennen.
♦ Dieses Gerät ist nicht wasser- oder spritzwassergeschützt. Sollte Feuchtigkeit, Flüssigkeit oder Nebelfluid in
das Geräteinnere eindringen, trennen Sie bitte das Nebelgerät sofort vom Netz und verständigen Sie einen
Servicetechniker oder Ihren ANTARI-Händler, bevor Sie das Gerät wieder in Betrieb nehmen.
♦ Keine zu wartenden Teile im Geräteinnern. Wartungsarbeiten sind nur vom Ihrem ANTARI-Händler oder
qualifizierten Servicetechnikern durchzuführen.
Brandgefahr
♦ Nur für Erwachsene. Das Nebelgerät muss außerhalb der Reichweite von Kindern installiert werden.
Betreiben Sie das Gerät niemals unbeaufsichtigt.
♦ Richten Sie die Nebelaustrittsdüse niemals direkt auf Personen.
♦ Der Ausstoß des Nebelgerätes ist sehr heiß. Halten Sie während des Betriebes einen Sicherheitsabstand
von ca. 60 cm zur Austrittsdüse ein.
♦ Installieren Sie das Nebelgerät an einem gut belüfteten Ort. Niemals die Lüftungsschlitze verdecken. Um
eine ausreichende Belüftung zu gewährleisten, halten Sie bitte einen Mindestabstand von 20 cm um und
über dem Gerät ein.
♦ Richten Sie die Austrittsdüse niemals auf offene Flammen.
♦ Wenn die Versorgungsschnur beschädigt wird, muss sie vom Hersteller oder dem Kundendienst oder
ähnlich qualifiziertem Personal ersetzt werden, um eine Gefahr zu vermeiden.
♦ Die Austrittdüse wird während des Betriebes sehr heiß (200° C). Für leicht entflammbare Materialien muss
ein Mindestabstand von 50 cm zur Austrittsdüse eingehalten werden.
♦ Lassen Sie Ihr ANTARI Nebelgerät vor Reinigungs- und Wartungsarbeiten abkühlen.
Loading...