QUICK START GUIDE
Getting started:
You may wish to reset the unit to factory settings to get started.
Go to: Menu --> Control --> Default Values --> Yes.
1. Select the Output resolution that matches the native
resolution of your display. You will next be prompted to
choose enable follow mode if desired and output rate.
Menu
--
>
Output
--
>
Output format
--
>
1024x768 -->
Internal Ref --> 60 Hz.
2. The principle of Soft Edge Blending lies in projecting an
image on a wide screen thanks to two or more video
projectors displaying the same content.
We Invite you to read the User Manual if your skills are not
enough to achieve the necessary adjustments.
To see in the User Manual: Page 32 to 34 and page 50 to 54.
3. To display a source, select the [BACKGROUND LIVE]
layer (it will begin to blink) then, select a source (it will
also blink). Press [TAKE] to transition your source from
preview to program output.
There will always be a layer selected (blinking) and a source
selected (blinking) to the selected layer (blinking). To view on
preview or change the contents of a different layer, simply
select it. The Smart Edge has 2 layers available called:
[BACKGROUND LIVE] and [DSK].
Each layer will obscure your view other layer below.
4. To display a titling, select the [PIP] layer, (it will begin to
blink) then select your source (it will also blink). Press
[TAKE] to display the PIP on program out.
The title layer is only available by an external Remote Control
(RCS/RK-300/TRK-800/ORC50/ARC200).
The Layer selection section allows to adjust Layer size,
position, transparency or transitions.
The Keying/Tilting section allows to access keying and titling
controls and parameters.
The Key layer has similar capabilities than any other layers.
The only constraint is that this layer must necessarily contain a
source of keying that is already applied.
Otherwise the source will be converted to black.
RK-300, TRK-800 and RCS allow to control the Key Layer by
the [PIP2] button.
ORC50 or ARC200 allow to control the Key Layer by [PIP1]
button.
To see the layer beneath, you will need to clear or move the
layer that are the top.
5. To clear the PIP, select the layer (it will blink) then, select
[BLACK]. Press [TAKE] to remove the layer from the
program output.
IMPORTANT:
Simply selecting a menu item will not set it to that value.
Be sure to press the ENTER button when parametering the
menu items.
Smart Edge - Ref. STE100
Thank you for choosing Analog Way and the Smart Edge. By following these simple steps, you will be able to setup and
use your powerful Hi-Resolution Mixer Switcher with Dual Output Edge Blending within minutes. Discover the Smart
Edge extensive capabilities and intuitive interface while conguring your rst show, and unleash your creativity for a new
experience in show and event management by Analog Way.
What’s in the box
1 x Smart Edge (STE100)
1 x AC Power cable
2 x DVI-I male to HD15 female and DVI-D female breakout cable
1 x HD15 to 5 BNC cable
1 x Ethernet cross cable (for device update)
1 x Set of 3 audio 5-pin screw terminals
1 x RCS - Remote Control Software (PC only) *
1 x User Manual (PDF version) *
1 x Quick Start guide (PDF version) *
* Download on our website: www.analogway.com
Optional:
1 x Sync Cable for multiple machine mode (Ref. AW212080)
If required, front handles of the device can be dismantled,
but with caution.
The original screws removed must not be reintroduced to
their location without handles in place.
Substantial damages can occur, including risk of electric shock from the mains voltage.
WARNING !
Only M4x12mm screws can be used.
(They are supplied with the unit)
Quick install and setup
Smart Edge - Ref. STE100
Front Panel Description
Keying and titling are
available with an external
!
Remote Control
CONTROL
EXIT/MENU: Home Menu or back one level
ENTER: Validates the menu or command
DSK ADJUST
Select to access keying and titling
controls and parameters
INPUT SELECTION
#1 to #6: Press to access analog source #1 to #6
DVI 1 to DVI 2: Press to access DVI #1 or DVI #2
SDI 1 to SDI 2: Press to access SDI #1 or SDI #2
BLACK: Clear the active layer
Adjust active layer
FREEZE
Freeze the input linked to the current layer
on MAIN
EFFECT
Select a custom transition
STAND-BY
Hold for 3 seconds for stand-by Mode
TAKE
Display the selected sources onto the
MAIN output with the selected effects
PRESET
Recall a custom stored preset (4 memories available).
To store a preset use Menu -> Presets
B U T T O N C OL O R US AG E
#1 = Source is on the main outputs
Solid red: #2 = Freeze enable
#3 = Stand-by button
#4 = Preset Selection
Solid green: #1 = Source is on Preview
Blinking red: Layer/source selected, and is currently active on
the main output
Blinking green: Layer/source selected, and is not currently active
one the main output
#2 = Function available for modication
O U T P UT S E TU P
1- Press the EXIT/MENU button from the Home menu
[all functions must be conrmed by the ENTER button]
2- Press [Output]
3- Press [Output format]
4- On Format line, select the display’s native resolution
5- Control or adjust your display device
6- If necessary, select [Test Pattern] in the Output menu
I N P U T S E T UP
1- Press the EXIT/MENU button from the Home menu [all functions must be
conrmed by the ENTER button]
2- Press [Input] and [Autoset ALL]
3- If the acquisition has failed, check all connections and perform a manual setup
4- For a comprehensive Input Setup, please refer to user’s Manual
5- For a manual input setup, press the EXIT/MENU button:
a) Press [Input],
b) Select the right input from Input #1 up to SDI #2, then
c) Select [Type].
NOTE: To adjust input Size or Pos, use the [Layer] Menus.
To adjust Blanking, use the Auto-Centering or Blanking adjustments in the
Image menu.
Smart Edge - Ref. STE100
4
L+
L-
R+
R-
BALANCED
L+
R+
L-
R-
GROUND(S)
Right
Left
Ground
Rear Panel Description
RS-232 communication port on a DB9 female
connector or TCP/IP on RJ45 connector
Universal Analog Computer/TV/HDTV inputs
#1 to #4
Power supply: IEC/EN/UL/CSA
60950-1, internal, autoswitchable
IP-LAN connectors
SD-SDI/HD-SDI inputs #1 & #2: female BNC
Outputs #1 & #2: female HD15, DVI-I
(simultaneous analog and digital outputs)
DVI connectors: DVI-D inputs #1 and #2 on
the DVI-I digital pins, and Universal Analog
inputs #5 & #6 on the DVI-I analog pins.
Use the included break-in cable.
3.5mm Jack Stereo
Connector input
(unbalanced)
Inputs #1 to #4
LEFT RIGHT
MCO Male connector for
input. DVI #1 & #2 and AUX
AUDIO OUTPUT
Main Audio Output (balanced)
W O R K IN G W IT H S T E 10 0
The features of STE100 can be controled by the external remote control as:
- Orchestra - Ref.: ORC50
- Axion2 - Ref.: ARC200
- Remote Control Software - Ref.: RCS (supplied)
- Triple Remote Control Keypad - Ref.: TRK-800
- Remote Control Keypad - Ref.: RK-300
RK-300, TRK-800 & RCS
!
can not be used in multiple
machine mode.
H O M E M E N U
The Home Menu is the system’s top level menu, from which all others menus can be
accessed. To access a menu, press the [MENU] button. To navigate in the Home
Menu, please use the knob. To conrm, please use the [ENTER] button. You can also
return to the Home Menu by pressing the [EXIT] button.
- INPUT: congure the 10 individual input types and resolutions
- OUTPUT #1: display the left image
- OUTPUT #2: display the right image
- PRESET: store and use presets
- IMAGE: change source image settings of an input
- KEYING/TITLING: access keying and titling controls and parameters
- LAYER: adjust Layer size, position, transparency or Transitions
- AUDIO: access all audio input and output parameters
- SOFTEDGE: access controls and parameters for Embedded Soft Edge Mode
- CONTROL: access device software information, LAN settings, reset factory settings,
amongst other user oriented functions (see next page)
- VIRTUAL T-Bar: select to access the Virtual T-Bar
A U D I O I N P UT S C O N NE CT IO N S
3.5mm Jack Stereo Connector
Inputs #1 to #4: Unbalanced connection
MCO Male Connectors
DVI #1 to DVI #2: Unbalanced connection
LEFT
Input #5
RIGHT
GROUND(S)
LEFT
Input #6
RIGHT
UNBALANCED
Input #7 (AUX): Balanced connection
Main Output: Balanced connection
L
5
R
L
6
R
NOTE: The updater les are available on our web site: http://www.analogway.com
Multiple Machine Mode
Up to 3 x STE100 for Large Wide Screen with 6 Video Projectors.
>> 1 x STE100 = 2 Video Projectors >> 2 x STE100 = 4 Video Projectors
LEFT RIGHT
No Sync Cable.
WARNING !
Sync Cable OPTIONAL.
For multiple machine mode, use one cable
per STE100 (Ref. AW212080).
For a perfect functioning, the follow mode
is recommanded on all units.
>> 3 x STE100 = 6 Video Projectors
LEFT
LEFT
LEFT
+ Sync Cable
RIGHT
LEFT
+ Sync Cable
RIGHT
+ Sync Cable
Thank you for using 2 x Sync Cable for multiple machine mode.
RIGHTRIGHT RIGHT
LEFT
+ Sync Cable
+ Sync Cable
+ Sync Cable
Thank you for using 3 x Sync Cable for multiple machine mode.
Warranty
This Analog Way product has a 3 year warranty on parts and labor, back to factory. This warranty does not include faults
resulting from user negligence, special modications, electrical surges, abuse (drop/crush), and/or other unusual damage.
Going further with the STE100
For complete details and operations procedures, please refer to the Smart Edge User’s Manual and our website for further
information: www.analogway.com.
Version : 4.00 - 14/12/11
Code : 140127
Loading...