Page 1
Programmer’s Guide
For SMX100
1
Page 2
A1: Introduction
If you need to use your own Software Control program from a PC or WORKSTATION with an RS-232 or LAN port, the device allows communication
through an ASCII code protocol.
The device treats any character that it receives on the RS-232 or LAN as a possible command but only accepts legal commands.
There is no starting/ending code needed in a command string.
A command can be a single character typed on a keyboard and does not require any special character before or after it.
(It is not necessary to press "ENTER" on the keyboard). A command can be preceded by a value (See chapter A-2).
When the device receives a valid command, it will execute the command. Then it will send back the status of the parameters that have changed due
to this command.
If the command cannot be executed (value out of range, no signal on the selected input),etc. The device will just sends back the current status of
the corresponding parameters.
If the command is invalid, an error response will be returned to the control device. All responses returned to the control device end with
a carriage return <CR> and a line feed <LF> signaling the end of the response character string (see chapter A-3).
A2: Commands structure
The above listed devices share the same code structure.
Commands are made of numerical values for arguments followed by the command characters (one or Two case-sensitive alphabetical letters). Usually the same
characters (letters) are used for the [read Command] as well as the [write command].
The indexes are defined numbers indicating the how the arguments for the command apply. For example a layer number, an input number, a preset number, etc.
They are separated with a comma.
There are commands without index and others with up to 3 indexes. Each index is followed by a comma character. The final argument, also refered to as the “value”
does not have a comma between it and the command.
2
Page 3
A [write command] is made of indexes followed by the numerical value followed by the command characters.
Write command = [[index,] ...] + Value + Character (s) code (s)
For example: “1,2,0IN” or “4YB”
A [read command] is made of indexes followed immediately by the command characters. (no numerical value)
Read command = [[index,] ...] Character (s) code (s)
For example: “1,2,IN” or “YB”
A3: Examples
Document notation:
1) Command with 1 index : OFORMAT
Command to set the Main output format to XGA: 0,12OF
Answer: OF0,12<CR><LF> which mean that the main output format is now 1024x768
2) Command with 2 indexes : PE_INPUTNUM
Command to set the input 4 displayed in background layer of Next Preset: 1,2,4IN
Answer: IN1,1,4<CR><LF> which mean that the background layer of the next preset will display the input 4 signal
3) Read command without index : TAKEAVA
Read command to know if the TAKE command is available: TA
Answer: TA1<CR><LF> which mean that the device is ready to accept the TAKE command.
4) Read command with 2 indexes : SET_ASPECT_RATIO_OUT
Read command to know how is displayed a signal plugged on the input 4: 3,so
Answer: so3,2<CR><LF> which mean that the input 4 is displayed cropped
3
Page 4
A4: Error codes
Answer: E10<CR><LF> which mean invalid command
Answer: E11<CR><LF> which mean index value error (index value out of range)
Answer: E12<CR><LF> which mean index number error (too or few indexes)
Some commands are only available as [Read command], they are status and are colored in blue as this line.
Some commands are colored in yellow as this line to indicate they were added or modified in this version.
A5 COMMUNICATION PORTS
4
Page 5
Read /
Min
Max
Default
Apply factory settings to the
Auto reset
Auto reset
AXION
AUTO_LOCK
AUTO_TAKE
Automatic Take after an input change
AUTO_STEPBACK
Automatic preset toggle after a TAKE
Group Name CmdResp Description
DIESE # # Request the retrieval of all the variables Rd/Wr 0 1 0
SYSTEM
CONTROLS
READY * * Ready Device Flag Rd 0 1 0
DEV ? DEV MMS device type Rd 92 92 92 92 = SMX-100
UPDATER yU yU Device reboot for update Rd/Wr 0 255 0 1 then 254 => Reboot
FACTORYRESET YR YR
POSMEMORYRESET YE YE Erase stored image settings Rd/Wr 0 1 0
CSTORE YS YS
LOCK YK YK Device locking Rd/Wr 0 2 0
LCDBRIGHTNESS YB YB Front panel display brightness Rd/Wr 1 8 8 1, …, 8 = Brightness level, 12,5% step
KEYBRIGHTNESS Yb Yb Front panel keys brightness Rd/Wr 10 100 100 1, …, 100 = Brightness level, 1% step
TBAR_ENABLE YD YD Enable disable T-BAR Rd/Wr 0 1 1
COPKIND CK CK Kind of slow in-progress operation Rd 0 6 0
COPPROGRESS CP CP Progress percent of the slow operation Rd 0 100 0 Percent : 0 to 100%
PRESET_MATRIX_MGMT CR CR
yA yA Device is driven by Orchestra Rd/Wr 0 1 0
YL YL Forbide the use of a signal-less input Rd/Wr 0 1 1
YT YT
Ys Ys
FREEZE_MODE Ym Ym Input freeze mode Rd/Wr 0 1 0
device( except image settings )
FLASH memory writing in progess. Do
not power off
Preset management in matrix mode
from the front panel
Write
Value
value
Rd/Wr 0 1 0
Rd 0 1 0
Rd/Wr 0 3 0
Rd/Wr 0 1 0
Rd/Wr 0 1 0
Values Index #1 Index #2
value
0= Initialization in progress
1 = Ready
0 = Free
1 = Flash writing in progress
0 = No lock
1 = Locked menu
2 = Locked front panel
0 = None
1 = Auto centering
2 = Auto setting
3 = StandBy
4 = Picture recording
5 = Reset to default factory setting
6 = Reset User settings
0 = Preset management for both
outputs
1 = Preset management for current
output
2 = Preset management for output 1
3 = Preset management for output 2
0 = Device is not driven by ORC-50
1 = Device is driven by Orc-50
0 = Signal less input can be selected
1 = Signal less input can not be
selected
0 = AUTO-TAKE Disable
1 = AUTO-TAKE Enable
0 = AUTO- PRESET-TOGGLE Disable
1 = AUTO- PRESET-TOGGLE Enable
0 = Freeze by input
1 = Freeze all inputs
5
Page 6
Read /
Min
Max
Default
wS wS
wQ wQ
wN wN
wF wF
wR wR
wC wC
Group Name CmdResp Description
Back-up input when an input loose its
signal
Disable the the black fiilng of the
bakgrounfd live layer
Fill PIP with black depending on the
aspect ratio
Disable Frame and Ids on the preview
output
Standby mode Rd/Wr 0 1 0
Request for standby or wake up Rd/Wr 0 1 0
Message to wake-up an output display
device ( 50 characters)
Message to send an output display
device to sleep ( 50 characters)
Output display device UART speed Rd/Wr 0 3 2
Rd/Wr 0 4 0
STANDBY
VERSION
FRAME_ALERT Yf Yf
TRANSPARENT_BACKGROUND Yt Yt
BLACK_FILL bF bF
DISABLE_ID bI bI
STDBYSTATUS
STDBYREQUEST
STDBYPROJ_ON
STDBYPROJ_OFF
STDBYPROJ_RATE
STDBYPROJ_CTRL
VERI1 xi xi Byte 0 and 1 of the device ID Rd 0 655350 ex : AAAA
VERI2 xj xj Byte 2 and 3 of the device ID Rd 0 655350 ex : AAAA
VERI3 xk xk Byte 4 and 5 of the device ID Rd 0 655350 ex : AAAA
VERI4 xl xl Byte 6 and 7 of the device ID Rd 0 655350 ex : AAAA
Write
Value
value
Rd/Wr 0 12 0
Rd/Wr 0 1 1
Rd/Wr 0 1 0
Rd/Wr 0 1 0
Rd/Wr 0 255 0 min = 0 max = 49
Rd/Wr 0 255 0 min = 0 max = 49
Values Index #1 Index #2
value
0 = No input
1 = Input1
2 = Input2
3 = Input3
4 = Input4
5 = Input5
6 = Input6
9 = Input9
10 = Input10
11 = Input11
12 = Input12
0 = use BLACK_FILL
1 = Disable black filling only for
background
0 = Disable black filling
1 = Enable black filling
0 = Normal mode
1 = Standby mode
0 = Wake up
1 = Standby
0 = 1200bauds
1 = 2400bauds
2 = 9600bauds
3 = 19200bauds
0 = No request
1 = Wake up request
2 = Standby request
3 = Clear Wake up message
4 = Clear standby message
6
Page 7
Read /
Min
Max
Default
Auto
Auto
Group Name CmdResp Description
Checksum/version of the
programmable components
-setting request for all the inputs Rd/Wr 0 1 0
-setting request for the specified
input
INPUT
VERK xK xK
VERV xV xV Variable set version Rd 0 6553542
VERUPD xU xU Updater version Rd 0 655350
OPT yo yo Detected options Rd 0 655350
REV xR xR Moher board revision Rd 0 255 0
IN_AUTOSET_ALL Ia Ia
IN_AUTOSET Ii Ii
Write
Value
value
value
Rd/Wr 0 655350
Rd/Wr 0 1 0
Values Index #1 Index #2
0 = Number of
programmables
components
1 = Main micro-
bit 0 = Lan Module
bit 1 = SDI In 1 board (SDI 1 and 2)
bit 2 = Recording board
bit 3 = CF Caecina
bit 4 = CF Fannia
bit 5 = CF Thrasea
bit 6 = SDI In 2 board (SDI 3 and 4)
bit 7 = Audio Evolution
bit 8 = HDCP DVI In Evolution
controler
2 = Front panel
micro-controler
3 = FPGA Caecina
4 = FPGA Fannia
6 = Synchro CPLD
0 = Input1
1 = Input2
2 = Input3
3 = Input4
4 = Input5
5 = Input6
8 = Input9
9 = Input10
10 = Input11
11 = Input12
7
Page 8
Read /
Min
Max
Default
Group Name CmdResp Description
IN_USR_FORMAT iU iU
Format/standard of the input signal
corrected by user
Write
Value
value
Rd/Wr 0 42 0
Values Index #1 Index #2
value
0 = None
1 = Invalid
2 = Unknown
3 = SDTV NTSC
4 = SDTV PAL
5 = SDTV SECAM
6 = SDTV BW
7 = SDTV 480i
8 = SDTV 576i
9 = EDTV 480p
10 = EDTV 576p
11 = HDTV 720p
12 = HDTV 1035i
13 = HDTV 1080i
14 = HDTV 1080p
15 = HDTV 1080sF
16 = CPU VGA
17 = CPU 800x480
18 = CPU WVGA
19 = CPU SVGA
20 = CPU 1280x600
21 = CPU 720p RGB
22 = CPU XGA
23 = CPU WXGA
24 = CPU SWXGA
25 = CPU 800p RGB
26 = CPU SWXGA+
27 = CPU 1152x864
28 = CPU 900p RGB
29 = CPU 1600x900
30 = CPU 960p RGB
31 = CPU SXGA
32 = CPU 1360x1024
33 = CPU DILA4/3
34 = CPU SXGA+
35 = CPU WSXGA+
36 = CPU 1080p RGB
37 = CPU 2K
38 = CPU UXGA
39 = CPU WUXGA
40 = CPU 1920x1440
41 = CPU QXGA
42 = CPU 1366x768
0 = Input1
1 = Input2
2 = Input3
3 = Input4
4 = Input5
5 = Input6
8 = Input9
9 = Input10
10 = Input11
11 = Input12
8
Page 9
Read /
Min
Max
Default
13 = Analog Computer, separated H&V
14 = Analog Computer, composite TTL
Analog H sync load
Group Name CmdResp Description
IN_TYPE iK iK Input signal type Rd/Wr 0 17 13
IN_SYNC_LOAD il il
IN_USED iu iu Input is enabled Rd/Wr 0 1 1
Write
Value
value
Rd/Wr 0 1 0
Values Index #1 Index #2
value
0 = SDTV Composite
1 = SDTV Y/C
2 = SDTV/EDTV/HDTV RGBS
TTL/Analog
3 = SDTV/EDTV/HDTV RGB SOG
4 = SDTV/EDTV/HDTV YUV
5 = Computer SOG
6 = Computer H&V or Composite
(TTL/Analog)
7 = Computer B&W
8 = DVI-D EDTV/HDTV RGB 16-235
9 = DVI-D EDTV/HDTV YUV
10 = DVI-D Computer RGB 0-255
11 = DVI-D Computer RGB 16-235
12 = SDI SDTV/HDTV
synchro
synchro
15 = Analog Computer, composite
analog synchro
16 = Analog RGB video, composite
TTL synchro
17 = Analog RGB video, composite
analog synchro
0 = Hi-Z
1 = 75 ohm loaded
0 = Input1
1 = Input2
2 = Input3
3 = Input4
4 = Input5
5 = Input6
8 = Input9
9 = Input10
10 = Input11
11 = Input12
0 = Input1
1 = Input2
2 = Input3
3 = Input4
4 = Input5
5 = Input6
8 = Input9
9 = Input10
10 = Input11
11 = Input12
0 = Input1
1 = Input2
2 = Input3
3 = Input4
4 = Input5
5 = Input6
8 = Input9
9 = Input10
10 = Input11
11 = Input12
9
Page 10
Read /
Min
Max
Default
Group Name CmdResp Description
IN_SD_STD iS iS Decoded video standard Rd/Wr 0 7 0
IN_SD_STA iV iV Video Signal stability Rd/Wr 0 1 1
IN_SYNCHRONIZED iY iY VIS Synchronisation group Rd/Wr 0 3 0
IN_HDCP_ENABLE iH iH
IN_HDCP_CABLE_LEN iC iC Lenght of an DVI input cable Rd/Wr 0 2 0
KEYING IN_KEYING_TYPE KT KT Keying type Rd/Wr 0 4 0
Enable/disable the HDCP support of a
DVI input
Write
Value
value
Rd/Wr 0 1 1
Values Index #1 Index #2
value
0 = Auto
1 = NTSC (M,J)
2 = PAL (BDGHIN)
3 = PAL (M)
4 = PAL (N-Combination)
5 = NTSC 4.43
6 = SECAM
7 = PAL 60
0 = Stable Source ( DVD )
1 = VCR Source ( Video cassette
recorder )
0 = Does not belong to any VIS Group
1 = Groupe VIS 1 group for analog
input
2 = Groupe VIS 2 group for analog
input
3 = Groupe VIS 3 group for analog
input
0 = Less than 10 meter cable length
1 = 5 to 20 meters cable length
2 = More than 15 meters cable length
0 = No keying
1 = Luma Key Keying
2 = ChromaKey Keying
3 = Luma Key Keying + DSK
4 = ChromaKey Keying + DSK
0 = Input1
1 = Input2
2 = Input3
3 = Input4
4 = Input5
5 = Input6
8 = Input9
9 = Input10
10 = Input11
11 = Input12
0 = Input1
1 = Input2
2 = Input3
3 = Input4
4 = Input5
5 = Input6
8 = Input9
9 = Input10
10 = Input11
11 = Input12
0 = Input1
1 = Input2
2 = Input3
3 = Input4
4 = Input5
5 = Input6
8 = Input9
9 = Input10
10 = Input11
11 = Input12
10 = Input11
11 = Input12
10 = Input11
11 = Input12
0 = Input1
1 = Input2
2 = Input3
3 = Input4
4 = Input5
5 = Input6
8 = Input9
9 = Input10
10 = Input11
11 = Input12
10
Page 11
Read /
Min
Max
Default
Keying Tolerance (for chroma and luma
Group Name CmdResp Description
IN_KEYING_R_LEVEL KR KR Keying level (Red ) Rd/Wr 0 255 0
IN_KEYING_G_LEVEL KG KG Keying level (Green) Rd/Wr 0 255 255
IN_KEYING_B_LEVEL KB KB Keying level (Bule) Rd/Wr 0 255 0
IN_KEYING_TOLER KH KH
key)
Write
Value
value
value
Rd/Wr 0 255 10
Values Index #1 Index #2
0 = Input1
1 = Input2
2 = Input3
3 = Input4
4 = Input5
5 = Input6
8 = Input9
9 = Input10
10 = Input11
11 = Input12
0 = Input1
1 = Input2
2 = Input3
3 = Input4
4 = Input5
5 = Input6
8 = Input9
9 = Input10
10 = Input11
11 = Input12
0 = Input1
1 = Input2
2 = Input3
3 = Input4
4 = Input5
5 = Input6
8 = Input9
9 = Input10
10 = Input11
11 = Input12
0 = Input1
1 = Input2
2 = Input3
3 = Input4
4 = Input5
5 = Input6
8 = Input9
9 = Input10
10 = Input11
11 = Input12
11
Page 12
Read /
Min
Max
Default
Enable/disable the keying color grabber
Auto reset
Group Name CmdResp Description
IN_KEYING_LUMA_LOW_LEVEL KL KL Minimum luma level Rd/Wr 0 255 0
IN_KEYING_LUMA_HIGH_LEVEL KM KM Maximum luma level Rd/Wr 0 255 255
IN_KEYING_DSK_ALPHA KA KA Brightness of DSK background Rd/Wr 0 255 64
IN_KEYING_INVERT KI KI Invert keying area Rd/Wr 0 1 0
IN_KEYING_GRAB_ENABLE Kg Kg
IN_KEYING_GRAB_GET Kc Kc
IN_KEYING_GRAB_H Kh Kh Horizontal position of the grabber Rd/Wr 0 6553532768 Precent of OSCREEN_UTIL_V
IN_KEYING_GRAB_V Kv Kv Vertical position of the grabber Rd/Wr 0 6553532768
mode
Capture the coolor selected by the
grabber and apply the settings
Write
Value
value
Rd/Wr 0 1 0
Rd/Wr 0 1 0 Percent of OSCREEN_UTIL_H
Values Index #1 Index #2
value
0 = Disable the grabber
1 = Enable the grabber
0 = Input1
1 = Input2
2 = Input3
3 = Input4
4 = Input5
5 = Input6
8 = Input9
9 = Input10
10 = Input11
11 = Input12
0 = Input1
1 = Input2
2 = Input3
3 = Input4
4 = Input5
5 = Input6
8 = Input9
9 = Input10
10 = Input11
11 = Input12
0 = Input1
1 = Input2
2 = Input3
3 = Input4
4 = Input5
5 = Input6
8 = Input9
9 = Input10
10 = Input11
11 = Input12
0 = Input1
1 = Input2
2 = Input3
3 = Input4
4 = Input5
5 = Input6
8 = Input9
9 = Input10
10 = Input11
11 = Input12
12
Page 13
Read /
Min
Max
Default
Group Name CmdResp Description
SIG_HPOL sh sh Input H sync polarity Rd 0 1 0
SIG_VPOL sv sv Input V sync polarity Rd 0 1 0
INPUT
STATUS
SIG_SYNC_TYPE sK sK Input sync type Rd 0 3 0
SIG_FREQ_FIELD sf sf Input frame frequency Rd 0 655350 Unit = 1/100Hz
Write
Value
value
Values Index #1 Index #2
value
0 = Negative Synchro
1 = Positive Synchro
0 = Negative Synchro
1 = Positive Synchro
0 = Séparated Synchros H&V
1 = Composite TTL Synchro
2 = Composite Analog Synchro
3 = Synchro on Green (SOG)
0 = Input1
1 = Input2
2 = Input3
3 = Input4
4 = Input5
5 = Input6
8 = Input9
9 = Input10
10 = Input11
11 = Input12
0 = Input1
1 = Input2
2 = Input3
3 = Input4
4 = Input5
5 = Input6
8 = Input9
9 = Input10
10 = Input11
11 = Input12
0 = Input1
1 = Input2
2 = Input3
3 = Input4
4 = Input5
5 = Input6
8 = Input9
9 = Input10
10 = Input11
11 = Input12
0 = Input1
1 = Input2
2 = Input3
3 = Input4
4 = Input5
5 = Input6
8 = Input9
9 = Input10
10 = Input11
11 = Input12
13
Page 14
Read /
Min
Max
Default
Group Name CmdResp Description
SIG_FREQ_LINE sl sl Input line frequency Rd 0 655350 Unit = 1/100Hz
SIG_COMPLETE sc sc Input scan completed Rd 0 1 0
Write
Value
value
Values Index #1 Index #2
value
0 = scan in progress or failed
1 = scan completed
0 = Input1
1 = Input2
2 = Input3
3 = Input4
4 = Input5
5 = Input6
8 = Input9
9 = Input10
10 = Input11
11 = Input12
0 = Input1
1 = Input2
2 = Input3
3 = Input4
4 = Input5
5 = Input6
8 = Input9
9 = Input10
10 = Input11
11 = Input12
14
Page 15
Read /
Min
Max
Default
Group Name CmdResp Description
SIG_DETECTED_FORMAT sD sD Input detected format name Rd 0 42 0
Write
Value
value
Values Index #1 Index #2
value
0 = None
1 = Invalid
2 = Unknown
3 = SDTV NTSC
4 = SDTV PAL
5 = SDTV SECAM
6 = SDTV BW
7 = SDTV 480i
8 = SDTV 576i
9 = EDTV 480p
10 = EDTV 576p
11 = HDTV 720p
12 = HDTV 1035i
13 = HDTV 1080i
14 = HDTV 1080p
15 = HDTV 1080sF
16 = CPU VGA
17 = CPU 800x480
18 = CPU WVGA
19 = CPU SVGA
20 = CPU 1280x600
21 = CPU 720p RGB
22 = CPU XGA
23 = CPU WXGA
24 = CPU SWXGA
25 = CPU 800p RGB
26 = CPU SWXGA+
27 = CPU 1152x864
28 = CPU 900p RGB
29 = CPU 1600x900
30 = CPU 960p RGB
31 = CPU SXGA
32 = CPU 1360x1024
33 = CPU DILA4/3
34 = CPU SXGA+
35 = CPU WSXGA+
36 = CPU 1080p RGB
37 = CPU 2K
38 = CPU UXGA
39 = CPU WUXGA
40 = CPU 1920x1440
41 = CPU QXGA
42 = CPU 1366x768
0 = Input1
1 = Input2
2 = Input3
3 = Input4
4 = Input5
5 = Input6
8 = Input9
9 = Input10
10 = Input11
11 = Input12
15
Page 16
Read /
Min
Max
Default
Group Name CmdResp Description
SIG_CURRENT_FORMAT sF sF Input current format name Rd 0 42 0
Write
Value
value
Values Index #1 Index #2
value
0 = None
1 = Invalid
2 = Unknown
3 = SDTV NTSC
4 = SDTV PAL
5 = SDTV SECAM
6 = SDTV BW
7 = SDTV 480i
8 = SDTV 576i
9 = EDTV 480p
10 = EDTV 576p
11 = HDTV 720p
12 = HDTV 1035i
13 = HDTV 1080i
14 = HDTV 1080p
15 = HDTV 1080sF
16 = CPU VGA
17 = CPU 800x480
18 = CPU WVGA
19 = CPU SVGA
20 = CPU 1280x600
21 = CPU 720p RGB
22 = CPU XGA
23 = CPU WXGA
24 = CPU SWXGA
25 = CPU 800p RGB
26 = CPU SWXGA+
27 = CPU 1152x864
28 = CPU 900p RGB
29 = CPU 1600x900
30 = CPU 960p RGB
31 = CPU SXGA
32 = CPU 1360x1024
33 = CPU DILA4/3
34 = CPU SXGA+
35 = CPU WSXGA+
36 = CPU 1080p RGB
37 = CPU 2K
38 = CPU UXGA
39 = CPU WUXGA
40 = CPU 1920x1440
41 = CPU QXGA
42 = CPU 1366x768
0 = Input1
1 = Input2
2 = Input3
3 = Input4
4 = Input5
5 = Input6
8 = Input9
9 = Input10
10 = Input11
11 = Input12
16
Page 17
Read /
Min
Max
Default
Group Name CmdResp Description
SIG_FORMAT_LIST sL sL
SIG_SCANTYPE ss ss Input scan type Rd 0 3 0
SIG_HTOTAL_THEORIC sH sH Total number of pixels per line Rd 0 655350 Unit = pixels
SIG_HTOTAL_MAXI sM sM Maximal number of pixels per input line Rd 0 655350 Unit = pixels
Bit field of the fomats compatible with
the detected format
Write
Value
value
value
Rd 0 255 0
Values Index #1 Index #2
0 = Bits 0 to 7
Slice
1 = Bits 8 to 15
Slice
2 = Bits 16 to 23
Slice
3 = Bits 24 to 31
Slice
4 = Bits 32 to 39
Slice
5 = Bits 40 to 47
Slice
0 = Progressive
1 = Interleaved, Top field first
2 = Interleaved, Bottom field first
3 = Segmented frame
0 = Input1
1 = Input2
2 = Input3
3 = Input4
4 = Input5
5 = Input6
8 = Input9
9 = Input10
10 = Input11
11 = Input12
0 = Input1
1 = Input2
2 = Input3
3 = Input4
4 = Input5
5 = Input6
8 = Input9
9 = Input10
10 = Input11
11 = Input12
0 = Input1
1 = Input2
2 = Input3
3 = Input4
4 = Input5
5 = Input6
8 = Input9
9 = Input10
10 = Input11
11 = Input12
0 = Input1
1 = Input2
2 = Input3
3 = Input4
4 = Input5
5 = Input6
8 = Input9
9 = Input10
10 = Input11
11 = Input12
17
Page 18
Read /
Min
Max
Default
Group Name CmdResp Description
SIG_WIDTH sw sw Input displayed pixel count Rd 0 655350 Unit = pixels
SIG_HEIGHT st st Input displayed line count Rd 0 655350 Unit = pixels
SIG_HDCP sn sn Input HDCP status Rd 0 1 0
SIG_MEM_SLOT sS sS Memory slot index Rd 0 255 255
Write
Value
value
Values Index #1 Index #2
value
0 = Input1
1 = Input2
2 = Input3
3 = Input4
4 = Input5
5 = Input6
8 = Input9
9 = Input10
10 = Input11
11 = Input12
0 = Input1
1 = Input2
2 = Input3
3 = Input4
4 = Input5
5 = Input6
8 = Input9
9 = Input10
10 = Input11
11 = Input12
0 = Input1
1 = Input2
2 = Input3
3 = Input4
4 = Input5
5 = Input6
8 = Input9
9 = Input10
10 = Input11
11 = Input12
0 = Input1
1 = Input2
2 = Input3
3 = Input4
4 = Input5
5 = Input6
8 = Input9
9 = Input10
10 = Input11
11 = Input12
18
Page 19
Read /
Min
Max
Default
Group Name CmdResp Description
SET_HPOS SH SH Input horizontal position Rd/Wr 0 2048 1024 1024 = neutral
SET_VPOS SV SV Input vertical position Rd/Wr 0 2048 1024 1024 = neutral
INPUT
SETTINGS
SET_HSIZE Sw Sw Input horizontal size Rd/Wr 0 4096 2048 2048 = neutral
SET_VSIZE Sh Sh Input vertical size Rd/Wr 0 4096 2048 2048 = neutral
Write
Value
value
Values Index #1 Index #2
value
0 = Input1
1 = Input2
2 = Input3
3 = Input4
4 = Input5
5 = Input6
8 = Input9
9 = Input10
10 = Input11
11 = Input12
0 = Input1
1 = Input2
2 = Input3
3 = Input4
4 = Input5
5 = Input6
8 = Input9
9 = Input10
10 = Input11
11 = Input12
0 = Input1
1 = Input2
2 = Input3
3 = Input4
4 = Input5
5 = Input6
8 = Input9
9 = Input10
10 = Input11
11 = Input12
0 = Input1
1 = Input2
2 = Input3
3 = Input4
4 = Input5
5 = Input6
8 = Input9
9 = Input10
10 = Input11
11 = Input12
19
Page 20
Read /
Min
Max
Default
Group Name CmdResp Description
SET_BRIGHTNESS Sg Sg Input brightness Rd/Wr 0 255 128 128 = neutral
SET_CONTRAST Sc Sc Input Contrast Rd/Wr 0 255 128 128 = neutral
SET_COLOR Sr Sr Input color level Rd/Wr 0 255 128 128 = neutral
SET_HUE Su Su Input hue (NTSC only) Rd/Wr 0 255 128 128 = neutral
Write
Value
value
Values Index #1 Index #2
value
0 = Input1
1 = Input2
2 = Input3
3 = Input4
4 = Input5
5 = Input6
8 = Input9
9 = Input10
10 = Input11
11 = Input12
0 = Input1
1 = Input2
2 = Input3
3 = Input4
4 = Input5
5 = Input6
8 = Input9
9 = Input10
10 = Input11
11 = Input12
0 = Input1
1 = Input2
2 = Input3
3 = Input4
4 = Input5
5 = Input6
8 = Input9
9 = Input10
10 = Input11
11 = Input12
0 = Input1
1 = Input2
2 = Input3
3 = Input4
4 = Input5
5 = Input6
8 = Input9
9 = Input10
10 = Input11
11 = Input12
20
Page 21
Read /
Min
Max
Default
Auto reset
ADC R
Group Name CmdResp Description
SET_HTOTAL ST ST Input total pixel per line Rd/Wr 0 655350 Unit = pixels.
SET_PHASE SS SS Input Phase Rd/Wr 0 31 16
SET_AUTOCAD Sa Sa Input autocentering reques Rd/Wr 0 1 0
SET_USER_GAIN_R sr sr
channel adjustment (advanced
setting)
Write
Value
value
Rd/Wr 0 255 128 128 = neutral
Values Index #1 Index #2
value
0 = Input1
1 = Input2
2 = Input3
3 = Input4
4 = Input5
5 = Input6
8 = Input9
9 = Input10
10 = Input11
11 = Input12
0 = Input1
1 = Input2
2 = Input3
3 = Input4
4 = Input5
5 = Input6
8 = Input9
9 = Input10
10 = Input11
11 = Input12
0 = Input1
1 = Input2
2 = Input3
3 = Input4
4 = Input5
5 = Input6
8 = Input9
9 = Input10
10 = Input11
11 = Input12
0 = Input1
1 = Input2
2 = Input3
3 = Input4
4 = Input5
5 = Input6
8 = Input9
9 = Input10
10 = Input11
11 = Input12
21
Page 22
Read /
Min
Max
Default
ADC G channel adjustment (advanced
ADC B channel adjustment (advanced
Group Name CmdResp Description
SET_USER_GAIN_G sg sg
SET_USER_GAIN_B sb sb
SET_PULLDOWN_2_2 Sn Sn Enable/disable the auto 2:2 pulldown Rd/Wr 0 1 1
SET_PULLDOWN_3_2 Sp Sp Enable/disable the auto 3:2 pulldown Rd/Wr 0 1 1
setting)
setting)
Write
Value
value
Rd/Wr 0 255 128 128 = neutral
Rd/Wr 0 255 128 128 = neutral
Values Index #1 Index #2
value
0 = Disable automatic detection
1 = Enable automatic detection
0 = Disable automatic detection
1 = Enable automatic detection
0 = Input1
1 = Input2
2 = Input3
3 = Input4
4 = Input5
5 = Input6
8 = Input9
9 = Input10
10 = Input11
11 = Input12
0 = Input1
1 = Input2
2 = Input3
3 = Input4
4 = Input5
5 = Input6
8 = Input9
9 = Input10
10 = Input11
11 = Input12
0 = Input1
1 = Input2
2 = Input3
3 = Input4
4 = Input5
5 = Input6
8 = Input9
9 = Input10
10 = Input11
11 = Input12
0 = Input1
1 = Input2
2 = Input3
3 = Input4
4 = Input5
5 = Input6
8 = Input9
9 = Input10
10 = Input11
11 = Input12
22
Page 23
Read /
Min
Max
Default
Group Name CmdResp Description
SET_CROP_WIN_POS_H SI SI Cropping window horizontal position Rd/Wr 0 6553532768
SET_CROP_WIN_POS_V SJ SJ Cropping window vertical position Rd/Wr 0 6553532768
SET_CROP_WIN_SIZE_H SK SK Horizontal cropping Rd/Wr 0 589810 Percent = 65535 = 100%
SET_CROP_WIN_SIZE_V SL SL Vertical cropping Rd/Wr 0 589810 Percent = 65535 = 100%
Write
Value
value
Values Index #1 Index #2
value
Percent = 65535 = 100% : all cropping
on the left
Percent = 65535 = 100% : all cropping
on the top
0 = Input1
1 = Input2
2 = Input3
3 = Input4
4 = Input5
5 = Input6
8 = Input9
9 = Input10
10 = Input11
11 = Input12
0 = Input1
1 = Input2
2 = Input3
3 = Input4
4 = Input5
5 = Input6
8 = Input9
9 = Input10
10 = Input11
11 = Input12
0 = Input1
1 = Input2
2 = Input3
3 = Input4
4 = Input5
5 = Input6
8 = Input9
9 = Input10
10 = Input11
11 = Input12
0 = Input1
1 = Input2
2 = Input3
3 = Input4
4 = Input5
5 = Input6
8 = Input9
9 = Input10
10 = Input11
11 = Input12
23
Page 24
Read /
Min
Max
Default
Group Name CmdResp Description
SET_ASPECT_RATIO_IN si si Input image aspect ratio Rd/Wr 0 4 0
SET_ASPECT_RATIO_OUT so so Output image aspect ratio Rd/Wr 0 3 1
SET_OVER_SCAN sO sO input image Overscan/Underscan Rd/Wr 0 1 1
SET_FORCE_4_3 SF SF
Force the aspect ratio of PAL/NTSC
input to 4/3
Write
Value
value
Rd/Wr 0 1 1 1 = forced
Values Index #1 Index #2
value
0 = 4/3 Fullscreen
1 = 4/3 with 16/9 content + black
stripes
2 = 4/3 with 2.35 content + black
stripes
3 = 4/3 with 16/9 content without black
stripes
4 = 19/9 with 4/3 content + black
stripes
0 = Distorted, input aspect ratio not
preserved
1 = Not distorted, black bands added
2 = Not distorted, no black bands
added
3 = Not distorted and no scaling
0 = Input1
1 = Input2
2 = Input3
3 = Input4
4 = Input5
5 = Input6
8 = Input9
9 = Input10
10 = Input11
11 = Input12
0 = Input1
1 = Input2
2 = Input3
3 = Input4
4 = Input5
5 = Input6
8 = Input9
9 = Input10
10 = Input11
11 = Input12
0 = Input1
1 = Input2
2 = Input3
3 = Input4
4 = Input5
5 = Input6
8 = Input9
9 = Input10
10 = Input11
11 = Input12
0 = Input1
1 = Input2
2 = Input3
3 = Input4
4 = Input5
5 = Input6
8 = Input9
9 = Input10
10 = Input11
11 = Input12
24
Page 25
Read /
Min
Max
Default
3 = Memory Preset
4 = Memory Preset
5 = Memory Preset
6 = Memory Preset
Group Name CmdResp Description
SET_RESET_SETTINGS Ss Ss Current input default settings Rd/Wr 0 1 0
SET_FREEZE Sf Sf Freeze of the input Rd/Wr 0 1 0 1 = Freeze
SET_MOTION_DETECT Sm Sm 0 : max correction; 15 : min correction Rd/Wr 0 15 15
PRESET
ELEMENT
PE_INPUTNUM IN IN
Displayed input number or frame or
logo number
Write
Value
value
Rd/Wr 0 12 0
Values Index #1 Index #2
value
0 = No input
1 = Input1
2 = Input2
3 = Input3
4 = Input4
5 = Input5
6 = Input6
9 = Input9
10 = Input10
11 = Input11
12 = Input12
0 = Input1
1 = Input2
2 = Input3
3 = Input4
4 = Input5
5 = Input6
8 = Input9
9 = Input10
10 = Input11
11 = Input12
0 = Input1
1 = Input2
2 = Input3
3 = Input4
4 = Input5
5 = Input6
8 = Input9
9 = Input10
10 = Input11
11 = Input12
0 = Input1
1 = Input2
2 = Input3
3 = Input4
4 = Input5
5 = Input6
8 = Input9
9 = Input10
10 = Input11
11 = Input12
0 = Current preset
1 = Next preset
2 = Previous
preset
1
2
3
4
2 = Background
Layer for output 1
3 = Pip 1 Layer for
output1
Background Layer
for output 2 in
matrix mode
8 = Audio Output 1
9 = Audio Output 2
25
Page 26
Read /
Min
Max
Default
Memory Preset
4 = Memory Preset
5 = Memory Preset
6 = Memory Preset
Aa Aa Auxiliary
3 = Memory Preset
4 = Memory Preset
5 = Memory Preset
6 = Memory Preset
3 = Memory Preset
4 = Memory Preset
Preset
6 = Memory Preset
Group Name CmdResp Description
PE_SOURCENUM IS IS Source number Rd/Wr 0 64 0 Same Orc-50
PE_AUDIO_AUX_MUTE
PE_SMOOTH_MOVE ps ps « Smooth Move » activation Rd/Wr 0 1 1 1 = Enable.
input mixing enable Rd/Wr 0 1 0 1 = Enable.
Write
Value
value
Values Index #1 Index #2
value
0 = Current preset
1 = Next preset
2 = Previous
preset
3 =
1
2
3
4
0 = Current preset
1 = Next preset
2 = Previous
preset
1
2
3
4
0 = Current preset
1 = Next preset
2 = Previous
preset
1
2
5 = Memory
3
4
2 = Background
Layer for output 1
3 = Pip 1 Layer for
output1
Background Layer
for output 2 in
matrix mode
8 = Audio Output 1
9 = Audio Output 2
2 = Background
Layer for output 1
3 = Pip 1 Layer for
output1
Background Layer
for output 2 in
matrix mode
8 = Audio Output 1
9 = Audio Output 2
2 = Background
Layer for output 1
3 = Pip 1 Layer for
output1
Background Layer
for output 2 in
matrix mode
8 = Audio Output 1
9 = Audio Output 2
26
Page 27
Read /
Min
Max
Default
3 = Memory Preset
4 = Memory Preset
5 = Memory Preset
6 = Memory Preset
3 = Memory Preset
4 = Memory Preset
5 = Memory Preset
Preset
3 = Memory Preset
4 = Memory Preset
5 = Memory Preset
6 = Memory Preset
Group Name CmdResp Description
PE_NEW_ID pN pN Unique layer identifier number Rd/Wr 0 1 0
PE_POS_H pH pH Layer left H position on output screen Rd/Wr 0 6553532768
PE_POS_V pV pV Layer top V position on output screen Rd/Wr 0 6553532768
Write
Value
value
Values Index #1 Index #2
value
Unit = pixels ( 32768 = screen left
border )
Unit = pixels ( 32768 = screen top
border )
0 = Current preset
1 = Next preset
2 = Previous
preset
1
2
3
4
0 = Current preset
1 = Next preset
2 = Previous
preset
1
2
3
6 = Memory
4
0 = Current preset
1 = Next preset
2 = Previous
preset
1
2
3
4
2 = Background
Layer for output 1
3 = Pip 1 Layer for
output1
Background Layer
for output 2 in
matrix mode
8 = Audio Output 1
9 = Audio Output 2
2 = Background
Layer for output 1
3 = Pip 1 Layer for
output1
Background Layer
for output 2 in
matrix mode
8 = Audio Output 1
9 = Audio Output 2
2 = Background
Layer for output 1
3 = Pip 1 Layer for
output1
Background Layer
for output 2 in
matrix mode
8 = Audio Output 1
9 = Audio Output 2
27
Page 28
Read /
Min
Max
Default
3 = Memory Preset
Preset
5 = Memory Preset
6 = Memory Preset
3 = Memory Preset
4 = Memory Preset
5 = Memory Preset
6 = Memory Preset
3 = Memory Preset
4 = Memory Preset
5 = Memory Preset
6 = Memory Preset
Group Name CmdResp Description
PE_SIZE_H pW pW
PE_SIZE_V pS pS
PE_CROP_WIN_POS_H CH CH Cropping window horizontal position Rd/Wr 0 6553532768
Layer H size on output screen (without
borders)
Layer V size on output screen (without
borders)
Write
Value
value
Rd/Wr 0 655351600 Unit = pixels ( Max=16x2048 = 32768)
Rd/Wr 0 655351200 Unit = pixels (Max=16x2048 = 32768)
Values Index #1 Index #2
value
Unit = percent ( 65535 = 100% = : all
cropping on the left )
0 = Current preset
1 = Next preset
2 = Previous
preset
1
4 = Memory
2
3
4
0 = Current preset
1 = Next preset
2 = Previous
preset
1
2
3
4
0 = Current preset
1 = Next preset
2 = Previous
preset
1
2
3
4
2 = Background
Layer for output 1
3 = Pip 1 Layer for
output1
Background Layer
for output 2 in
matrix mode
8 = Audio Output 1
9 = Audio Output 2
2 = Background
Layer for output 1
3 = Pip 1 Layer for
output1
Background Layer
for output 2 in
matrix mode
8 = Audio Output 1
9 = Audio Output 2
2 = Background
Layer for output 1
3 = Pip 1 Layer for
output1
Background Layer
for output 2 in
matrix mode
8 = Audio Output 1
9 = Audio Output 2
28
Page 29
Read /
Min
Max
Default
3 = Memory Preset
4 = Memory Preset
6 = Memory Preset
3 = Memory Preset
4 = Memory Preset
5 = Memory Preset
6 = Memory Preset
3 = Memory Preset
4 = Memory Preset
5 = Memory Preset
6 = Memory Preset
Group Name CmdResp Description
PE_CROP_WIN_POS_V CV CV Cropping window vertical position Rd/Wr 0 6553532768
PE_CROP_WIN_SIZE_H CW CW Horizontal cropping Rd/Wr 0 589810 Percent = 65535 = 100%
PE_CROP_WIN_SIZE_V CS CS Vertical cropping Rd/Wr 0 589810 Percent = 65535 = 100%
Write
Value
value
Values Index #1 Index #2
value
Unit = percent ( 65535 = 100% = : all
cropping on the top )
0 = Current preset
1 = Next preset
2 = Previous
preset
1
2
5 = Memory Preset
3
4
0 = Current preset
1 = Next preset
2 = Previous
preset
1
2
3
4
0 = Current preset
1 = Next preset
2 = Previous
preset
1
2
3
4
2 = Background
Layer for output 1
3 = Pip 1 Layer for
output1
Background Layer
for output 2 in
matrix mode
8 = Audio Output 1
9 = Audio Output 2
2 = Background
Layer for output 1
3 = Pip 1 Layer for
output1
Background Layer
for output 2 in
matrix mode
8 = Audio Output 1
9 = Audio Output 2
2 = Background
Layer for output 1
3 = Pip 1 Layer for
output1
Background Layer
for output 2 in
matrix mode
8 = Audio Output 1
9 = Audio Output 2
29
Page 30
Read /
Min
Max
Default
3 = Memory Preset
4 = Memory Preset
5 = Memory Preset
6 = Memory Preset
3 = Memory Preset
4 = Memory Preset
5 = Memory Preset
6 = Memory Preset
3 = Memory Preset
4 = Memory Preset
Preset
6 = Memory Preset
Group Name CmdResp Description
PE_ALPHA pA pA Layer transparency Rd/Wr 0 255 255
PE_BORDER_STYLE bS bS Border style Rd/Wr 0 0 0 0 = No border
PE_BORDER_COLOR bC bC Border color Rd/Wr 0 544 33 Color number
Write
Value
value
Values Index #1 Index #2
value
0 = 100% = transparent
255 = 0% = visible
0 = Current preset
1 = Next preset
2 = Previous
preset
1
2
3
4
0 = Current preset
1 = Next preset
2 = Previous
preset
1
2
3
4
0 = Current preset
1 = Next preset
2 = Previous
preset
1
2
5 = Memory
3
4
2 = Background
Layer for output 1
3 = Pip 1 Layer for
output1
Background Layer
for output 2 in
matrix mode
8 = Audio Output 1
9 = Audio Output 2
2 = Background
Layer for output 1
3 = Pip 1 Layer for
output1
Background Layer
for output 2 in
matrix mode
8 = Audio Output 1
9 = Audio Output 2
2 = Background
Layer for output 1
3 = Pip 1 Layer for
output1
Background Layer
for output 2 in
matrix mode
8 = Audio Output 1
9 = Audio Output 2
30
Page 31
Read /
Min
Max
Default
3 = Memory Preset
4 = Memory Preset
5 = Memory Preset
6 = Memory Preset
3 = Memory Preset
4 = Memory Preset
5 = Memory Preset
6 = Memory Preset
3 = Memory Preset
4 = Memory Preset
5 = Memory Preset
6 = Memory Preset
Group Name CmdResp Description
PE_BORDER_ALPHA bA bA Border transparency Rd/Wr 0 255 255
PE_BORDER_SIZE_H bH bH Border H size Rd/Wr 0 127 10 Unit = pixels
PE_BORDER_SIZE_V bV bV Border V size Rd/Wr 0 127 10 Unit = pixels
Write
Value
value
Values Index #1 Index #2
value
0 = 100% = transparent
255 = 0% = visible
0 = Current preset
1 = Next preset
2 = Previous
preset
1
2
3
4
0 = Current preset
1 = Next preset
2 = Previous
preset
1
2
3
4
0 = Current preset
1 = Next preset
2 = Previous
preset
1
2
3
4
2 = Background
Layer for output 1
3 = Pip 1 Layer for
output1
Background Layer
for output 2 in
matrix mode
8 = Audio Output 1
9 = Audio Output 2
2 = Background
Layer for output 1
3 = Pip 1 Layer for
output1
Background Layer
for output 2 in
matrix mode
8 = Audio Output 1
9 = Audio Output 2
2 = Background
Layer for output 1
3 = Pip 1 Layer for
output1
Background Layer
for output 2 in
matrix mode
8 = Audio Output 1
9 = Audio Output 2
31
Page 32
Read /
Min
Max
Default
3 = Memory Preset
4 = Memory Preset
5 = Memory Preset
6 = Memory Preset
3 = Memory Preset
Memory Preset
5 = Memory Preset
6 = Memory Preset
3 = Memory Preset
4 = Memory Preset
5 = Memory Preset
6 = Memory Preset
Group Name CmdResp Description
PE_OPENING_TRANSITION oT oT Layer opening transition type Rd/Wr 0 2 2
PE_OPENING_TRANSITION_WAY oW oW Layer opening transition direction Rd/Wr 0 10 0
PE_OPENING_DURATION oD oD Layer opening transition duration Rd/Wr 0 255 10 Unit = 1/10s
Write
Value
value
Values Index #1 Index #2
value
0 = Cut
2 = Fade
0 = Current preset
1 = Next preset
2 = Previous
preset
1
2
3
4
0 = Current preset
1 = Next preset
2 = Previous
preset
1
4 =
2
3
4
0 = Current preset
1 = Next preset
2 = Previous
preset
1
2
3
4
2 = Background
Layer for output 1
3 = Pip 1 Layer for
output1
Background Layer
for output 2 in
matrix mode
8 = Audio Output 1
9 = Audio Output 2
2 = Background
Layer for output 1
3 = Pip 1 Layer for
output1
Background Layer
for output 2 in
matrix mode
8 = Audio Output 1
9 = Audio Output 2
2 = Background
Layer for output 1
3 = Pip 1 Layer for
output1
Background Layer
for output 2 in
matrix mode
8 = Audio Output 1
9 = Audio Output 2
32
Page 33
Read /
Min
Max
Default
3 = Memory Preset
4 = Memory Preset
Preset
6 = Memory Preset
3 = Memory Preset
4 = Memory Preset
5 = Memory Preset
6 = Memory Preset
3 = Memory Preset
4 = Memory Preset
5 = Memory Preset
6 = Memory Preset
Available TAKE flag
Group Name CmdResp Description
PE_CLOSING_TRANSITION cT cT Layer closing transition type Rd/Wr 0 2 2
PE_CLOSING_TRANSITION_WAY cW cW Layer closing transition direction Rd/Wr 0 10 0
PE_CLOSING_DURATION cD cD Layer closing transition duration Rd/Wr 0 255 10 Unit = 1/10s
TAKE TK TK TAKE, Next preset becomes Current Rd/Wr 0 1 0
PRESET
CONTROL
TAKEAVA TA TA
TAKEINFO TI TI TAKE information Rd 0 2 0
TBAR NT NT TBAR value Rd/Wr 0 100000 Unit = 0,01%
Write
Value
value
Rd 0 1 1
Values Index #1 Index #2
value
0 = Cut
2 = Fade
0 = 1 shot TAKE
1 = 2 shot TAKE
2 = Sequenced TAKE
0 = Current preset
1 = Next preset
2 = Previous
preset
1
2
5 = Memory
3
4
0 = Current preset
1 = Next preset
2 = Previous
preset
1
2
3
4
0 = Current preset
1 = Next preset
2 = Previous
preset
1
2
3
4
2 = Background
Layer for output 1
3 = Pip 1 Layer for
output1
Background Layer
for output 2 in
matrix mode
8 = Audio Output 1
9 = Audio Output 2
2 = Background
Layer for output 1
3 = Pip 1 Layer for
output1
Background Layer
for output 2 in
matrix mode
8 = Audio Output 1
9 = Audio Output 2
2 = Background
Layer for output 1
3 = Pip 1 Layer for
output1
Background Layer
for output 2 in
matrix mode
8 = Audio Output 1
9 = Audio Output 2
33
Page 34
Read /
Min
Max
Default
Auto reset
Previewed layed (layer that is visible on
Anti
Group Name CmdResp Description
COPY_FROM Nf Nf Source for preset copy Rd/Wr 0 6 0
COPY_TO Nt Nt Destination for preset copy Rd/Wr 0 6 0
COPY_SPLIT Ns Ns Preset partial copy control Rd/Wr 0 2 0
COPY_CTRL Nc Nc Preset copy control Rd/Wr 0 1 0
SETTINGS
PREVIEWED_LAYER NC NC
SET_QUAD_LAYOUT NQ NQ
R_FLICK Rf Rf
R_GAMMA Rg Rg Gamma correction level Rd/Wr 5 40 10 Unit = 1/10
R_SHARPNESS Rs Rs Sharpness correction Level Rd/Wr 0 255 128 128 = neutral
preview screen)
Quadravision Layout request (autoreset)
-flicker level Rd/Wr 0 7 2 0 = No antif-flicker
Write
Value
value
Rd/Wr 2 7 2
Rd/Wr 13 13 0 13 = Reset of layer properties
Values Index #1 Index #2
value
0 = Current preset
1 = Next preset
2 = Previous preset
3 = Memory Preset 1
4 = Memory Preset 2
5 = Memory Preset 3
6 = Memory Preset 4
0 = Current preset
1 = Next preset
2 = Previous preset
3 = Memory Preset 1
4 = Memory Preset 2
5 = Memory Preset 3
6 = Memory Preset 4
0 = Full Preset copy
1 = Output1 preset copy
2 = Output2 preset copy
2 = Background Layer for output 1
3 = Pip 1 Layer for output1
Background Layer for output 2 in
matrix mode
8 = Audio Output 1
9 = Audio Output 2
0 = Main output
1 = Preview output
0 = Main output
1 = Preview output
0 = Main output
1 = Preview output
34
Page 35
Read /
Min
Max
Default
Group Name CmdResp Description
OUTPUT OFORMAT OF OF Output format Rd/Wr 0 37 0
Write
Value
value
Values Index #1 Index #2
value
0 = PAL
1 = NTSC
2 = 480p
3 = 576p
4 = SMPTE296M
5 = SMPTE260M
6 = SMPTE274M
7 = SMPTE274M
8 = SMPTE274M
9 = 640 x 480 4/3
10 = 848 x 480 16/9
11 = 800 x 600 4/3
12 = 1024 x 768 4/3
13 = 1360 x 768 16/9
14 = 1280 x 800 16/9
15 = 1280 x 1024 5/4
16 = 1400 x 1050 5/3
17 = 1680 x 1050 16/9
18 = 1600 x 1200 4/3
19 = 1920 x 1200 16/9
20 = 2048 x 1080
21 = 1280 x 720 16/9
22 = 1920 x 1080 16/9
23 = 1920 x 1080 16/9 (HD)
24 = 1920 x 1080 16/9 (SHARP)
25 = 1920 x 1080 16/9 (SHARP 2)
26 = 1440 x 900 16/10
27 = 1280 x 768 15/9
28 = 1366 x 800 15/9
29 = 1366 x 768 16/9
30 = Computer Custom 1
31 = Computer Custom 2
32 = Computer Custom 3
33 = Computer Custom 4
34 = Computer Custom 5
35 = Computer Custom 6
36 = Computer Custom 7
37 = Computer Custom 8
0 = Main output
1 = Preview output
35
Page 36
Read /
Min
Max
Default
Analog output type
Analog
Group Name CmdResp Description
ORATE OR OR Output rate Rd/Wr 0 12 8
OSIGTYPEANALOG OA OA
OSIGTYPEDIGITAL OD OD Digital output type Rd/Wr 0 2 0
OSYNCPOL OS OS
output sync polarity Rd/Wr 0 3 0
Write
Value
value
Rd/Wr 0 3 0
Values Index #1 Index #2
value
0 = Custom Field Rate
1 = 23,97 Hz
2 = 24 Hz
3 = 25 Hz
4 = 29,97 Hz
5 = 30 Hz
6 = 50 Hz
7 = 59,94 Hz
8 = 60 Hz
9 = 72 Hz
10 = 75 Hz
11 = 85 Hz
12 = 100 Hz
0 = RGBs
1 = RGsB (SOG)
2 = RGB H&V
3 = YUV
0 = RGB 0-255 ( full scale )
1 = RGB 16-235 ( reduced scale )
2 = YUV
0 = negative H&V synchro
1 = Synchros H négative et V positive
2 = Synchros H positive et V négative
3 = Synchros H et V positives
0 = Main output
1 = Preview output
0 = Main output
1 = Preview output
0 = Main output
1 = Preview output
0 = Main output
1 = Preview output
36
Page 37
Read /
Min
Max
Default
Group Name CmdResp Description
OBACKCOLORPREDEF OC OC Output background pre-defined color Rd/Wr 0 32 0
OBACKCOLORHUE OG OG Output background hue Rd/Wr 0 240 160
OBACKCOLORSAT OJ OJ Output background saturation Rd/Wr 0 240 0
OBACKCOLORLUMA OI OI Output background brightness Rd/Wr 0 240 0
Write
Value
value
Values Index #1 Index #2
value
0 = Black
1 = Navy blue
2 = Blue
3 = Green Blue
4 = Water Blue
5 = Turquoise blue
6 = Dark green
7 = Green
8 = Lime
9 = Light green
10 = Dark red
11 = Red
12 = Tomato red
13 = Bordeaux
14 = Brown
15 = Chocolate
16 = Orange
17 = Gold
18 = Yellow
19 = Indigo blue
20 = Purple
21 = Light red
22 = Fuchsia
23 = Salmon
24 = Rose
25 = Olive reen
26 = Grey
27 = Silver
28 = Lavender blue
29 = Beige
30 = Azur
31 = White
32 = Custom
0 = Main output
1 = Preview output
0 = Main output
1 = Preview output
0 = Main output
1 = Preview output
0 = Main output
1 = Preview output
37
Page 38
Read /
Min
Max
Default
Xr Xr
Group Name CmdResp Description
OPATTERN OP OP Output test pattern Rd/Wr 0 8 0
OBLACK OB OB Output black control Rd/Wr 0 1 0
OUTIL_H OH OH Output H size Rd 0 655351600 Unit = pixels
OUTIL_V OV OV Output V size Rd 0 655351200 Unit = pixels
OFIELDRATE OT OT Output frame frequency Rd 100 100006000 Unit = 1/100Hz
OIMAGE_OVERSCAN OO OO Image Overscan / Underscan Rd/Wr 0 1 0
OSETDETECTHDCP Oh Oh
OISHDCP On On Output HDCP status Rd 0 1 0
OSYNCOUTPUT Om Om
REFERENCEREFREQUEST
Enable/disable the Output HDCP
detection
Output 2 copies the format and rate of
output 1
Framelock source requested by user Rd/Wr 0 15 0
Write
Value
value
Rd/Wr 0 4 1
Rd/Wr 0 1 0
Values Index #1 Index #2
value
0 = No pattern
1 = Vertical Grey Scale
2 = Horizontal Grey Scale
3 = Vertical Color Bar
4 = Horizontal Color Bar
5 = Grid
6 = SMPTE
7 = Burst
8 = Centering
0 = Normal output
1 = Black output
0 = Disable HDCP detection
1 = Automatic HDCP detection
2 = HDCP Configuration 1
3 = HDCP Configuration 2
4 = HDCP Configuration 3
0 = Analog input 1 as reference
1 = Analog input 2 as reference
2 = Analog input 3 as reference
3 = Analog input 4 as reference
4 = Analog input 5 as reference
5 = Analog input 6 as reference
8 = DVI 1 input as reference
9 = DVI 2 input as reference
10 = SDI 1 input as reference
11 = SDI 2 input as reference
14 = Back End 1 as reference
15 = Back End 2 as reference
0 = Main output
1 = Preview output
0 = Main output
1 = Preview output
0 = Main output
1 = Preview output
0 = Main output
1 = Preview output
0 = Main output
1 = Preview output
0 = Main output
1 = Preview output
0 = Main output
1 = Preview output
0 = Main output
1 = Preview output
0 = Main output
1 = Preview output
38
Page 39
Read /
Min
Max
Default
Xe Xe
Xm Xm
Xc Xc
Xt Xt
Xl Xl
Auto reset
Auto reset
1 = IP address mid
2 = IP address mid
3 = IP address low
Group Name CmdResp Description
LAN
REFCURRENTREQUEST
REFMODE
REFCURRENTMODE
REFFREQ
REFLOCKSTATUS
LANENABLE ne ne LAN enable Rd/Wr 0 1 0
LANRESET nr nr LAN factory parameters reset Rd/Wr 0 1 0
LANSTORE ns ns LAN parameters update Rd/Wr 0 1 0
LANIP nw nw LAN devices addresses Rd/Wr 0 255 192 IP : 0 to 255
Current Frame Lock source Rd/Wr 0 15 0
Follow mode requested by user Rd/Wr 0 5 0
Current follow mode Rd/Wr 0 5 0
Frame rate of the reference signal Rd 0 655350 Unit = 1/100Hz
Framelock locked status Rd 0 1 0 1 = locked
Write
Value
value
Values Index #1 Index #2
value
0 = Analog input 1 as reference
1 = Analog input 2 as reference
2 = Analog input 3 as reference
3 = Analog input 4 as reference
4 = Analog input 5 as reference
5 = Analog input 6 as reference
8 = DVI 1 input as reference
9 = DVI 2 input as reference
10 = SDI 1 input as reference
11 = SDI 2 input as reference
14 = Back End 1 as reference
15 = Back End 2 as reference
0 = Internal
1 = Follow x1/2
2 = Follow x1
3 = Follow x2
4 = Follow x3
5 = Asynchronous Follow
0 = Internal
1 = Follow x1/2
2 = Follow x1
3 = Follow x2
4 = Follow x3
5 = Asynchronous Follow
0 = Enable RS232 ( disable LAN )
1 = Enable LAN ( disable RS232 )
0 = Main output
1 = Preview output
0 = Main output
1 = Preview output
0 = Main output
1 = Preview output
0 = Main output
1 = Preview output
0 = Main output
1 = Preview output
0 = Device
1 = Remote
2 = Gateway
0 = IP address
high byte
high byte
low high byte
LANPORT np np LAN port numbers Rd/Wr 0 6553510500
LANNETMASK nk nk LAN netmask Rd/Wr 0 24 8 Number of 0bits from the right
39
Local port : 10000 à 10999
Remote port : 0 à 65500
0 = Device
1 = Remote
2 = Gateway
byte
Page 40
Read /
Min
Max
Default
AUDIO
AUDIO_INPUT_MODE
Af Af Audio mode
Group Name CmdResp Description
LANPROTOCOL nt nt LAN protocol Rd/Wr 0 1 1
EDID_FORMAT EF EF EDID preferred format Rd/Wr 0 21 0
EDID
EDID_RATE ER ER EDID preferred frame frequency Rd/Wr 0 5 0
EDID_REQUEST ES ES Request for an EDID Rd/Wr 0 2 0
Write
Value
value
Rd/Wr 0 1 1
Values Index #1 Index #2
value
0 = UDP Protocol
1 = TCP protocol
2 = AMX Protocol
0 = VGA
1 = 800x480
2 = WVGA
3 = SVGA
4 = 720pRGB
5 = XGA
6 = WXGA
7 = SWXGA
8 = 800pRGB
9 = 1152x864
10 = 900pRGB
11 = 1600x900
12 = 960pRGB
13 = SXGA
14 = 1360x1024
15 = SXGA+
16 = WSXGA+
17 = 1080pRGB
18 = 2K
19 = UXGA
20 = WUXGA
21 = Custom
0 = 50 Hz
1 = 60 Hz
2 = 72 Hz
3 = 75 Hz
4 = 85 Hz
5 = Custom
0 = EDID is ready
1 = EDID saving
2 = EDID reading
0 = Free choice of audio input
1 = Audio input follow the top layers
0 = Analog input 1
1 = Analog input 2
3 = DVI-D input 1
4 = DVI-D input 2
0 = Analog input 1
1 = Analog input 2
3 = DVI-D input 1
4 = DVI-D input 2
0 = Analog input 1
1 = Analog input 2
3 = DVI-D input 1
4 = DVI-D input 2
40
Page 41
Read /
Min
Max
Default
AUDIO_INPUT_MAP
Ai Ai Audio input map
AUDIO_LEVEL
AL AL Audio input level
AUDIO_AUX_LEVEL
Al Al Audio auxiliary input level
AUDIO_BALANCE
Ab Ab Audio input balance
0 = max to the left, 45 = centered, 90 =
AUDIO_AUX_BALANCE
AB AB Audio auxiliary input balance
0 = max to the left, 45 = centered, 90 =
AUDIO_MUTE
Au Au Audio output Mute control
AUDIO_MASTER_VOLUME
AV AV
AUDIO_MODE
Am Am Audio stero mode
AUDIO_DELAY
AD AD
AUDIO_AUTO_DELAY
Ae Ae Automatic audio delay
Group Name CmdResp Description
Output Master volume Rd/Wr 0 255 255 0 = mute, 32 = -18dB , 255 = 0dB
Delay between audio and video Rd/Wr 0 80 0
Write
Value
value
Rd/Wr 0 12 1
Rd/Wr 0 255 45 Linear scale, init value is 0 dB
Rd/Wr 0 255 45 Linear scale, init value is 0 dB
Rd/Wr 0 90 45
Rd/Wr 0 90 45
Rd/Wr 0 1 0 1 = Mute.
Rd/Wr 0 1 1
Rd/Wr 0 1 1
Values Index #1 Index #2
value
0 = No input
1 = Input1
2 = Input2
3 = Input3
4 = Input4
5 = Input5
6 = Input6
9 = Input9
10 = Input10
11 = Input11
12 = Input12
max to the right
max to the right
0 = mono
1 = Stereo
0 = no delay
500ms = max delay
0 = réglage manuel du Delay, 1 =
reglage automatique du delay
0 = Input1
1 = Input2
2 = Input3
3 = Input4
4 = Input5
5 = Input6
8 = Input9
9 = Input10
10 = Input11
11 = Input12
0 = Input1
1 = Input2
2 = Input3
3 = Input4
4 = Input5
5 = Input6
8 = Input9
9 = Input10
10 = Input11
11 = Input12
0 = Input1
1 = Input2
2 = Input3
3 = Input4
4 = Input5
5 = Input6
8 = Input9
9 = Input10
10 = Input11
11 = Input12
0 = Main output
1 = Preview output
0 = Main output
1 = Preview output
0 = Main output
1 = Preview output
0 = Main output
1 = Preview output
41
Page 42
Read /
Min
Max
Default
AUDIO_SDI_CHAN_LEFT
Ac Ac
AUDIO_SDI_CHAN_RIGHT
AC AC
AUDIO_DESEMB
As As
Group Name CmdResp Description
END_LOCKED
ID of the Sdi channel to desembed for
left channel
ID of the Sdi channel to desembed for
right channel
Information of audio channel presence
for SDI inputs
Write
Value
value
Rd/Wr 0 15 0
Rd/Wr 0 15 1
Rd 0 1 1 1 : Locked
Values Index #1 Index #2
value
0 = Group A – Channel 1
1 = Group A – Channel 2
2 = Group A – Channel 3
3 = Group A – Channel 4
4 = Group B – Channel 1
5 = Group B – Channel 2
6 = Group B – Channel 3
7 = Group B – Channel 4
8 = Group C – Channel 1
9 = Group C – Channel 2
10 = Group C – Channel 3
11 = Group C – Channel 4
12 = Group D – Channel 1
13 = Group D – Channel 2
14 = Group D – Channel 3
15 = Group D – Channel 4
0 = Group A – Channel 1
1 = Group A – Channel 2
2 = Group A – Channel 3
3 = Group A – Channel 4
4 = Group B – Channel 1
5 = Group B – Channel 2
6 = Group B – Channel 3
7 = Group B – Channel 4
8 = Group C – Channel 1
9 = Group C – Channel 2
10 = Group C – Channel 3
11 = Group C – Channel 4
12 = Group D – Channel 1
13 = Group D – Channel 2
14 = Group D – Channel 3
15 = Group D – Channel 4
10 = Channel 11 –
SDI 1
11 = Channel 11 –
SDI 2
12 = Channel 11 –
SDI 3
13 = Channel 12 –
SDI 4
10 = Channel 11 –
SDI 1
11 = Channel 11 –
SDI 2
12 = Channel 11 –
SDI 3
13 = Channel 12 –
SDI 4
10 = Channel 11 –
SDI 1
11 = Channel 11 –
SDI 2
12 = Channel 11 –
SDI 3
13 = Channel 12 –
SDI 4
42
Page 43
43
Loading...