User’s Manual
MODEL: DSV1600
MODEL: SSV1600
ANALOG WAY® SCAN 1600 / DIGI SCAN 1600 EDITION : 06 / 07
SCAN 1600 / DIGI SCAN 1600
SAFETY INSTRUCTIONS
All of the safety and operating instructions should be read before the product is operated and should be retained for further
reference. Please follow all of the warnings on this product and its operating instructions.
ENGLISH
CAUTION
:
WARNING: To prevent the risk of electric shock and fire, do not expose this device to rain, humidity or intense
heat sources (such as heaters or direct sunlight). Slots and openings in the device are provided for
ventilation and to avoid overheating. Make sure the device is never placed on or near a textile
surface that could block the openings. Also keep away from excessive dust, vibrations and shocks.
POWER: Only use the power supply indicated on the device or on the power source. Devices equipped with a
grounding plug should only be used with a grounding type outlet. In no way should this grounding
be modified, avoided or suppressed.
POWER CORD: Use the On (I) / Off (O) switch to power On or Off devices equipped with that switch. All other
devices should be plugged and unplugged from wall outlet. In both cases, please follow these
instructions:
- The power cord of the device should be unplugged from the outlet when left unused for several
days.
- To unplug the device, do not pull on the power cord but always on the plug itself.
- The outlet should always be near the device and easily accessible.
- Power supply cords should be routed so that they are not likely to be walked on or pinched by
items placed upon or against them.
If the power supply cord is damaged, unplug the device. Using the device with a damaged power
supply cord may expose you to electric shocks or other hazards. Verify the condition of the power
supply cords once in a while. Contact your dealer or service center for replacement if damaged.
CONNECTIONS: All inputs and outputs (except for the power input) are TBTS defined under EN60950.
SERVICING: Do not attempt to service this product yourself by opening or removing covers and screws since it
may expose you to electric shocks or other hazards. Refer all problems to qualified service
personnel.
OPENINGS: Never push objects of any kind into this product through the openings. If liquids have been spilled or
objects have fallen into the device, unplug it immediately and have it checked by a qualified
technician.
PAGE 2
SCAN 1600 / DIGI SCAN 1600
Ç
INSTRUCTIONS DE SÉCURITÉ
Afin de mieux comprendre le fonctionnement de cet appareil nous vous conseillons de bien lire toutes les consignes de sécurité et de fonctionnement de
l’appareil avant utilisation. Conserver les instructions de sécurité et de fonctionnement afin de pouvoir les consulter ultérieurement. Respecter toutes les
consignes marquées dans la documentation, sur le produit et sur ce document.
ATTENTION : Afin de prévenir tout risque de choc électrique et d’incendie, ne pas exposer cet appareil à la pluie, à l’humidité et aux sources de chaleur
intense.
INSTALLATION : Veillez à assurer une circulation d’air suffisante pour éviter toute surchauffe à l’intérieur de l’appareil. Ne placez pas l’appareil sur ou
proximité de surface textile susceptible d’obstruer les orifices de ventilation. N’installez pas l’appareil à proximité de sources de chaleur comme un radiateur
ou une bouche d’air chaud, ni dans un endroit exposé au rayonnement solaire direct, à des poussières excessives, à des vibrations ou à des chocs mécaniques.
Ceci pourrait provoquer un mauvais fonctionnement et un accident.
ALIMENTATION : Ne faire fonctionner l’appareil qu’avec la source d’alimentation indiquée sur l’appareil ou sur son bloc alimentation. Pour les appareils
équipés d’une alimentation principale avec fil de terre, ils doivent être obligatoirement connectés sur une source équipée d’une mise à la terre efficace. En
aucun cas cette liaison de terre ne devra être modifiée, contournée ou supprimée.
CORDON D’ALIMENTATION : Pour les appareils équipés d’un interrupteur général (Marche I / Arrêt O), la mise sous tension et la mise hors tension se fait
en actionnant cet interrupteur général. Pour les appareils sans interrupteur général, la mise sous tension et la mise hors tension se fait directement en
connectant et déconnectant le cordon d'alimentation de la prise murale.
Dans les 2 cas ci-dessus appliquer les consignes suivantes :
- Débrancher le cordon d'alimentation de la prise murale si vous prévoyez de ne pas utiliser l'appareil pendant quelques jours ou plus.
- Pour débrancher le cordon, tirez le par la fiche. Ne tirez jamais sur le cordon proprement dit.
- La prise d’alimentation doit se trouver à proximité de l’appareil et être aisément accessible.
- Ne laissez pas tomber le cordon d’alimentation et ne posez pas d’objets lourds dessus.
Si le cordon d’alimentation est endommagé, débranchez le immédiatement de la prise murale. Il est dangereux de faire fonctionner cet appareil avec un cordon
endommagé, un câble abîmé peut provoquer un risque d’incendie ou un choc électrique. Vérifier le câble d’alimentation de temps en temps. Contacter votre
revendeur ou le service après vente pour un remplacement.
CONNEXIONS : Toutes les entrées et sorties (exceptée l’entrée secteur) sont de type TBTS (Très Basse Tension de Sécurité) définies selon EN 60950.
RÉPARATION ET MAINTENANCE : L’utilisateur ne doit en aucun cas essayer de procéder aux opérations de dépannage, car l’ouverture des appareils par
retrait des capots ou de toutes autres pièces constituant les boîtiers ainsi que le dévissage des vis apparentes à l’extérieur, risque d’exposer l’utilisateur à des
chocs électriques ou autres dangers. Contacter le service après vente ou votre revendeur ou s’adresser à un personnel qualifié uniquement.
OUVERTURES ET ORIFICES : Les appareils peuvent comporter des ouvertures (aération, fentes, etc...), veuillez ne jamais y introduire d’objets et ne jamais
obstruer ses ouvertures. Si un liquide ou un objet pénètre à l’intérieur de l’appareil, débranchez immédiatement l’appareil et faites le contrôler par un personnel
qualifié avant de le remettre en service.
ISTRUZIONI DI SICUREZZA
Allo scopo di capire meglio il funzionamento di questa apparecchiatura vi consigliamo di leggere bene tutti i consigli di sicurezza e di funzionamento prima
dell’utilizzo. Conservare le istruzioni di sicurezza e di funzionamento al fine di poterle consultare ulteriormente. Seguire tutti i consigli indicati su questo
manuale e sull’apparecchiatura.
ATTENZIONE : Al fine di prevenire qualsiasi rischio di shock elettrico e d’incendio, non esporre l’apparecchiatura a pioggia, umidità e a sorgenti di
eccessivo calore.
INSTALLAZIONE : Assicuratevi che vi sia una sufficiente circolazione d’aria per evitare qualsiasi surriscaldamento all’interno dell’apparecchiatura. Non
collocare l’apparecchiatura in prossimità o su superfici tessili suscettibili di ostruire il funzionamento della ventilazione. Non installate l’apparecchiatura in
prossimità di sorgenti di calore come un radiatore o una fuoruscita d’aria calda, né in un posto esposto direttamente ai raggi del sole, a polvere eccessiva, a
vibrazioni o a shock meccanici. Ció potrebbe provocare un erroneo funzionamento e un incidente.
ALIMENTAZIONE : Far funzionare l’apparecchiatura solo con la sorgente d’alimentazione indicata sull’apparecchiatura o sul suo alimentatore. Per le
apparecchiature fornite di un’alimentazione principale con cavo di terra, queste devono essere obbligatoriamente collegate su una sorgente fornita di una
efficiente messa a terra. In nessun caso questo collegamento potrà essere modificato, sostituito o eliminato.
CAVO DI ALIMENTAZIONE : Per le apparecchiature fornite di interruttore generale (Acceso I / Spento O), l’accensione e lo spegnimento
dell’apparecchiatura si effettuano attraverso l’interruttore. Per le apparecchiature senza interruttore generale, l’accensione e lo spegnimento si effettuano
direttamente inserendo o disinserendo la spina del cavo nella presa murale.
In entrambe i casi applicare i seguenti consigli :
- Disconnettere l’apparecchiatura dalla presa murale se si prevede di non utilizzarla per qualche giorno.
- Per disconnettere il cavo tirare facendo forza sul connettore.
- La presa d’alimentazione deve trovarsi in prossimità dell’apparecchiatura ed essere facilmente accessibile.
- Non far cadere il cavo di alimentazione né appoggiarci sopra degli oggetti pesanti.
Se il cavo di alimentazione é danneggiato, spegnere immediatamente l’apparecchiatura. E’ pericoloso far funzionare questa apparecchiatura con un cavo di
alimentazione danneggiato, un cavo graffiato puó provocare un rischio di incendio o uno shock elettrico. Verificare il cavo di alimentazione spesso. Contattare
il vostro rivenditore o il servizio assistenza per una sostituzione.
CONNESSIONE : Tutti gli ingressi e le uscite (eccetto l’alimentazione) sono di tipo TBTS definite secondo EN 60950.
RIPARAZIONI E ASSISTENZA : L’utilizzatore non deve in nessun caso cercare di riparare l’apparecchiatura, poiché con l’apertura del coperchio metallico o
di qualsiasi altro pezzo costituente la scatola metallica, nonché svitare le viti che appaiono esteriormente, poiché ció puó provocare all’utilizzatore un rischio
di shock elettrico o altri rischi.
APERTURE DI VENTILAZIONE : Le apparecchiature possono comportare delle aperture di ventilazione, si prega di non introdurre mai oggetti o ostruire le
sue fessure. Se un liquido o un oggetto penetra all’interno dell’apparecchiatura, disconnetterla e farla controllare da personale qualificato prima di rimetterla in
servizio.
AIS ITALIANO
FRAN
PAGE 3
SCAN 1600 / DIGI SCAN 1600
SICHERHEITSHINWEISE
Um den Betrieb dieses Geräts zu verstehen, raten wir Ihnen vor der Inbetriebnahme alle Sicherheits- und Betriebsanweisungen genau zu lesen. Diese
Sicherheits- und Betriebsanweisungen für einen späteren Gebrauch sicher aufbewahren. Alle in den Unterlagen, an dem Gerät und hier angegebenen
Sicherheitsanweisungen einhalten.
VORSICHT & WARNUNG
ACHTUNG: um jegliches Risiko eines Stromschlags oder Feuers zu vermeiden, das Gerät nicht Regen, Feuchtigkeit oder intensiven Wärmequellen aussetzen.
EINBAU : Eine ausreichende Luftzufuhr sicherstellen, um jegliche Überhitzung im Gerät zu vermeiden. Das Gerät nicht auf und in Nähe von
Textiloberflächen, die Belüftungsöffnungen verschließen können, aufstellen. Das Gerät nicht in Nähe von Wärmequellen, wie z.B. Heizkörper oder
Warmluftkappe, aufstellen und es nicht dem direkten Sonnenlicht, übermäßigem Staub, Vibrationen oder mechanischen Stößen aussetzen. Dies kann zu
Betriebsstörungen und Unfällen führen.
STROMVERSORGUNG : Das Gerät nur mit der auf dem Gerät oder dem Netzteil angegebenen Netzspannung betreiben. Geräte mit geerdeter
Hauptstromversorgung müssen an eine Stromquelle mit effizienter Erdung angeschlossen werden. Diese Erdung darf auf keinen Fall geändert, umgangen oder
entfernt werden.
STROMKABEL : Für Geräte mit einem Hauptschalter (Ein/Aus) erfolgt die Stromversorgung und Unterbrechung mittels dieses Hauptschalters. Geräte ohne
Hauptschalter werden durch das Einstecken oder Herausziehen des Steckers in den Wandanschluß ein- oder ausgeschaltet. Für beide Fälle gelten folgende
Richtlinien :
- Den Stecker aus dem Wandanschluß herausziehen wenn Sie das Gerät mehrere Tage oder länger nicht benutzen.
- Das Kabel mittels dem Stecker herausziehen. Niemals am Stromkabel selbst ziehen.
- Die Steckdose muß sich in der Nähe des Geräts befinden und leicht zugänglich sein.
- Das Stromkabel nicht fallen lassen und keine schweren Gegenstände auf es stellen.
Wenn das Stromkabel beschädigt ist, das Gerät sofort abschalten. Es ist gefährlich das Gerät mit einem beschädigten Stromkabel zu betreiben; ein abgenutztes
Kabel kann zu einem Feuer oder Stromschlag führen. Das Stromkabel regelmäßig untersuchen. Für den Ersatz, wenden Sie sich an Ihren Verkäufer oder
Kundendienststelle.
ANSCHLÜSSE : Bei allen Ein- und Ausgängen (außer der Stromversorgung) handelt es sich, gemäß EN 60950, um Sicherheits- Kleinspannunganschlüsse.
REPARATUR UND WARTUNG : Der Benutzer darf keinesfalls versuchen das Gerät selbst zu reparieren, die Öffnung des Geräts durch Abnahme der
Abdeckhaube oder jeglichen anderen Teils des Gehäuses sowie die Entfernung von außen sichtbaren Schrauben zu Stromschlägen oder anderen Gefahren für
den Benutzer führen kann. Wenden Sie sich an Ihren Verkäufer, Ihre Kundendienststelle oder an qualifizierte Fachkräfte.
ÖFFNUNGEN UND MUNDUNGEN : Die Geräte können über Öffnungen verfügen (Belüftung, Schlitze, usw.). Niemals Gegenstände in die Öffnungen
einführen oder die Öffnungen verschließen. Wenn eine Flüssigkeit oder ein Gegenstand in das Gerät gelangt, den Stecker herausziehen und es vor einer neuen
Inbetriebnahme von qualifiziertem Fachpersonal überprüfen lassen.
INSTRUCCIONES DE SEGURIDAD
Para comprender mejor el funcionamiento de este aparato, le recomendamos que lea cuidadosamente todas las consignas de seguridad y de funcionamiento del
aparato antes de usarlo. Conserve las instrucciones de seguridad y de funcionamiento para que pueda consultarlas posteriormente. Respete todas las consignas
indicadas en la documentación, relacionadas con el producto y este documento.
PRECAUCIONES Y OBSERVACIONES
CUIDADO : Para prevenir cualquier riesgo de choque eléctrico y de incendio, no exponga este aparato a la lluvia, a la humedad ni a fuentes de calorintensas.
INSTALACIÓN : Cerciórese de que haya una circulación de aire suficiente para evitar cualquier sobrecalentamiento al interior del aparato. No coloque el
aparato cerca ni sobre una superficie textil que pudiera obstruir los orificios de ventilación. No instale el aparato cerca de fuentes de calor como radiador o
boca de aire caliente, ni en un lugar expuesto a los rayos solares directos o al polvo excesivo, a las vibraciones o a los choques mecánicos. Esto podría
provocar su mal funcionamiento o un accidente.
ALIMENTACIÓN : Ponga a funcionar el aparato únicamente con la fuente de alimentación que se indica en el aparato o en su bloque de alimentación. Los
aparatos equipados con una alimentación principal con hilo de tierra deben estar conectados obligatoriamente a una fuente equipada con una puesta a tierra
eficaz. Por ningún motivo este enlace de tierra deberá ser modificado, cambiado o suprimido.
ESPAÑOL DEUTSCH
CABLE DE ALIMENTACIÓN : Para los aparatos equipados con un interruptor general (Marcha I / Paro O), la puesta bajo tensión y la puesta fuera de tensión
se hace accionando este interruptor general.. En los aparatos que no tienen interruptor general, la puesta bajo tensión y la puesta fuera de tensión se hace
directamente conectando y desconectando el enchufe mural.
En ambos casos, se deberá respetar las siguientes consignas:
- Desconectar el aparato del enchufe mural si no piensa utilizarlo durante varios días.
- Para desconectar el cable, tire de la clavija. No tire nunca del cable propiamente dicho.
- El enchufe de alimentación debe estar cerca del aparato y ser de fácil acceso.
- No deje caer el cable de alimentación ni coloque objetos pesados encima de él.
Si el cable de alimentación sufriera algún daño, ponga el aparato inmediatamente fuera de tensión. Es peligroso hacer funcionar este aparato con un cable
averiado, ya que un cable dañado puede provocar un incendio o un choque eléctrico. Verifique el estado del cable de alimentación de vez en cuando. Póngase
en contacto con su distribuidor o con el servicio de posventa si necesita cambiarlo.
CONEXIONES : Todas las entradas y salidas (excepto la entrada del sector) son de tipo TBTS (Muy Baja Tensión de Seguridad) definidas según EN 60950.
REPARACIÓN Y MANTENIMIENTO : Por ningún motivo, el usuario deberá tratar de efectuar operaciones de reparación, ya que si abre los aparatos
retirando el capó o cualquier otra pieza que forma parte de las cajas o si destornilla los tornillos aparentes exteriores, existe el riesgo de producirse una
explosión, choques eléctricos o cualquier otro incidente. Contacte el servicio de posventa, a su distribuidor o dirigirse con personal cualificado únicamente.
ABERTURAS Y ORIFICIOS : Los aparatos pueden contener aberturas (aireación, ranuras, etc.). No introduzca allí ningún objeto ni obstruya nunca estas
aberturas. Si un líquido o un objeto penetra al interior del aparato, desconéctelo y hágalo revisar por personal cualificado antes de ponerlo nuevamente en
servicio.
PAGE 4
SCAN 1600 / DIGI SCAN 1600
TABLE OF CONTENTS
SAFETY INSTRUCTIONS...........................................................................................................................................................
2
QUICK START GUIDE – DIGI SCAN 1600 ...............................................................................................................................6
QUICK START GUIDE – SCAN 1600.........................................................................................................................................7
Chapter 1 : INTRODUCTION.......................................................................................................................................................8
1-1. ACCESSORIES SUPPLIED WITH THE DIGI SCAN 1600.............................................................................................8
1-2. ACCESSORIES SUPPLIED WITH THE SCAN 1600......................................................................................................8
1-3. DIGI SCAN 1600 GENERAL INFORMATION...............................................................................................................8
1-4. SCAN 1600 GENERAL INFORMATION.........................................................................................................................9
1-5. DEVICES & OPTIONS REFERENCES............................................................................................................................9
1-6. INSTALLATION................................................................................................................................................................9
1-7. DIGI SCAN 1600 FRONT PANEL DESCRIPTION.......................................................................................................10
1-8. DIGI SCAN 1600 REAR PANEL DESCRIPTION .........................................................................................................10
1-9. SCAN 1600 FRONT PANEL DESCRIPTION ................................................................................................................11
1-10. SCAN 1600 REAR PANEL DESCRIPTION.................................................................................................................11
Chapter 2 : STARTING ...............................................................................................................................................................12
2-1. DIGI SCAN 1600 CONNECTIONS: ...............................................................................................................................12
2-2. SCAN 1600 CONNECTIONS:.........................................................................................................................................13
2-3. SETTINGS........................................................................................................................................................................13
2-4. IMAGE ADJUSTMENTS................................................................................................................................................13
Chapter 3 : FRONT PANEL DISPLAY MENU DESCRIPTION...............................................................................................14
3-1. INTRODUCTION ............................................................................................................................................................14
3-2. CONTROL BUTTONS ....................................................................................................................................................14
3-3. STATUS MODE...............................................................................................................................................................14
3-4. CONTROL MODE...........................................................................................................................................................15
3-5. FUNCTIONS DESCRIPTION .........................................................................................................................................16
Chapter 4 : UPDATING THE DEVICE ......................................................................................................................................18
Chapter 5 : REMOTE CONTROL SOFTWARE.........................................................................................................................19
5-1. CONNECTIONS ..............................................................................................................................................................19
5-2. SOFTWARE INSTALLATION.......................................................................................................................................19
5-3. COMMUNICATION SETUP...........................................................................................................................................19
5-4. USING THE SOFTWARE...............................................................................................................................................20
Chapter 6 : TECHNICAL SPECIFICATIONS............................................................................................................................22
6-1. COMPUTER INPUTS......................................................................................................................................................22
6-2. VIDEO OUTPUTS...........................................................................................................................................................22
6-3. GENLOCK .......................................................................................................................................................................23
6-4. REMOTE PORT...............................................................................................................................................................23
6-5. ENVIRONMENTAL........................................................................................................................................................23
APPENDIX A: PROGRAMMER'S GUIDE................................................................................................................................24
WARRANTY...............................................................................................................................................................................28
PAGE 5
QUICK START GUIDE – DIGI SCAN 1600
ANALOG WAY EDITION : 06/07
CONNECTIONS:
c Turn OFF all of your equipment before connecting.
d Connect the AC power supply cord to the DIGI SCAN 1600 and to an AC power outlet.
e Connect your computer source to the COMPUTER INPUT (HD15) connector or the DVI-D INPUT connector.
f As required, connect a control monitor on the MONITOR OUT (HD15) connector.
: Set the RGB Hi-Z/75 Ω button on Hi-Z if you connect a monitor on the MONITOR OUT connector. If not set
NOTE
it on 75 Ω.
NOTE:
g Connect your display devices (TV monitor, VCR...) to the outputs (analog or SDI).
h Turn ON the DIGI SCAN 1600 (rear panel switch). Then turn ON your input source and then your display devices.
• DIGI SCAN 1600 connection diagram:
The MONITOR OUT is available only if the COMPUTER source is analog.
6
2
4
Ω
3
5
5
• RGB/COMPONENT output connection:
SETTINGS:
c We recommend resetting the DIGI SCAN 1600 to all of its default values, with the front panel display menu (Control >
default value > yes) before proceeding.
d Select the Input source (ANALOG or DVI) with the front panel display menu (Input > Input select.).
e Select the Output standard with the front panel display menu (Output > output std).
f Select the Output rate mode (internal or genlock) with the front panel display menu (Output > output rate).
g Select the type of the RGB/YUV output with the front panel display menu (Output > RGB/YUV out).
h As required, make the following adjustments:
-Select the UNDERSCAN mode with the front panel display menu (Image > under/over).
-Adjust the image position & size with the front panel buttons.
-Adjust the level of anti-flicker with the panel display menu (Image > flicker filter).
-Make the others adjustments, available in the Image menu.
QUICK START GUIDE – SCAN 1600
ANALOG WAY EDITION : 06/07
CONNECTIONS:
c Turn OFF all of your equipment before connecting.
d Connect your computer source to the COMPUTER INPUT (HD15) connector or the DVI-D INPUT connector.
e As required, connect a control monitor on the MONITOR OUT (HD15) connector.
: Set the RGB Hi-Z/75 Ω button on Hi-Z if you connect a monitor on the MONITOR OUT connector. If not set
NOTE
it on 75 Ω.
NOTE:
f Connect your display devices (TV monitor, VCR...) to the outputs.
g Connect the external power supply to an AC power outlet and to the DC input connector of the SCAN 1600. Then turn
ON your input sources and then your display devices.
• SCAN 1600 connection diagram:
The MONITOR OUT is available only if the COMPUTER source is analog.
3
Ω
2
4
5
• RGB/COMPONENT output connection:
SETTINGS:
c We recommend resetting the SCAN 1600 to all of its default values, with the front panel display menu (Control >
default value > yes) before proceeding.
d Select the Input source (ANALOG or DVI) with the front panel display menu (Input > Input select.).
e Select the Output standard with the front panel display menu (Output > output std).
f Select the type of the RGB/YUV output with the front panel display menu (Output > RGB/YUV out).
g As required, make the following adjustments:
-Select the UNDERSCAN mode with the front panel display menu (Image > under/over).
-Adjust the image position & size with the front panel buttons.
-Adjust the level of anti-flicker with the panel display menu (Image > flicker filter).
-Make the others adjustments, available in the Image menu.
SCAN 1600 / DIGI SCAN 1600
SCAN 1600 & DIGI SCAN 1600
Chapter 1 : INTRODUCTION
1-1. ACCESSORIES SUPPLIED WITH THE DIGI SCAN 1600
• 1 DIGI SCAN 1600
• 1 AC mains cable.
• 1 VGA cable (HD15 male / HD15 male)
• 1 CD-ROM (Remote Control Software).
• 1 User’s Manual.
1-2. ACCESSORIES SUPPLIED WITH THE SCAN 1600
• 1 SCAN 1600
• 1 External power supply
• 1 AC mains cable.
• 1 VGA cable (HD15 male / HD15 male)
• 1 CD-ROM (Remote Control Software).
• 1 User’s Manual.
Supplied equipment with the OPT-RMK2 option (Rack Mount Kit):
• 1 rack tablet.
• 2 screws.
1-3. DIGI SCAN 1600 GENERAL INFORMATION
Digi Scan 1600 by Analog Way is a Professional Scan Converter with Genlock and Digital SDI output to convert PC,
Mac or Workstation graphic images up to1600x1200 at 60Hz into Video. Ready for the new generation of computer
graphic cards, Digi Scan 1600 also offers a standard DVI-D input and SDI output for a fully digital signal processing. It
is totally Auto-Scan and converts in real time, full screen image, with overscan /underscan and frame freeze functions.
Digi Scan 1600 outputs at the same time SDI, RGB/S or YUV, S.Video and Composite in NTSC or PAL (4 pin Mini
DIN, BNC). SDI signal is 10 bits, 4.2.2, meeting SMPTE 259 timing specifications. Digi Scan 1600 comes with High
performance Genlock to overlay graphics onto incoming Video (with external switcher). All of the Line & Subcarrier
phase parameters are adjustable, and meet ITU-R/SMPTE specifications. Genlock uses a Black Burst (or Composite)
Video signal. It includes an active loop through to daisy chain other devices. Digi Scan 1600 includes Computer input
format memory: User adjustments for up to 16 different input formats are stored in the device permanent memory. It
makes this device ideal and very useful for rental or multi-computer applications. Digi Scan 1600 features linear
Pan/Zoom up to 500% to display from 100% to 4% of any part of the total input image area. A large range Anti-Flicker
(8 levels) enables to find the right settings to match your application. It also offers R, G, B and Black Level adjustments
for a precise user color setting. In addition, a loop through out of the RGB input is available for monitoring. User
friendly menus displayed on a blue illuminated LCD screen provide clear and simple user controls. Digi Scan 1600 can
be fully controlled and updated via RS232 serial COM port. Control software is provided with the device and updates
can be downloaded from Analog Way website. Digi Scan 1600 is very easy to use and provides professional high
quality Video signal.
PAGE 8
SCAN 1600 / DIGI SCAN 1600 Chapter 1 : INTRODUCTION (continued)
1-4. SCAN 1600 GENERAL INFORMATION
Scan 1600 by Analog Way is a Scan Converter to convert PC, Mac or Workstation graphic images up to 1600x1200
at60Hz into Video. Ready for the new generation of computer graphic cards, it also offers a standard DVI-D input for
digital signal. It is totally Auto-Scan and converts in real time, full screen image, with overscan / underscan and frame
freeze functions. Scan 1600 outputs simultaneously Composite, S.Video and RGB/S or YUV in NTSC or PAL (4 pin
Mini DIN, BNC). Scan 1600 includes Computer input format memory: User Adjustments for up to 16 different input
formats are stored in the device permanent memory. It makes this device ideal and very useful for rental or multicomputer applications. Scan 1600 features linear Pan/Zoom up to 500% to display from 100% to 4% of any part of the
total input image area. A large range Anti-Flicker processing (8 levels) allows to find easily the right settings to match
your application. It also offers R, G, B and Black Level adjustments for a precise user color setting. In addition, a loop
through out of the RGB input is available for monitoring. An LCD screen enables an easy navigation through the
menus. Scan 1600 can be fully controlled and updated via RS232 serial COM port. Control software is provided with
the device and updates can be downloaded from Analog Way website. Scan 1600 is very easy to use and provides a
high quality Video signal.
1-5. DEVICES & OPTIONS REFERENCES
REFERENCE DESIGNATION
DSV1600 DIGI SCAN 1600
SSV1600 SCAN 1600.
OPT-RMK2 Rack Mounting Kit (optional) : allows mounting 2 SSV1600 in 1U 19" rack.
1-6. INSTALLATION
IMPORTANT:
• Table Top Mounting:
• Rack Mounting:
Please read all the safety instructions (pages 2 to 4) before starting.
The devices can be used directly on a table: they are equipped with 4 plastic feet.
The SCAN 1600 is compatible with a 19" enclosure (optional rack mount kit: OPT-RMK2).
To install the device into a 19” rack: Remove the 4 plastic feet, fix the tablet to the device
using the front side screw of the device and fix the supplied screw to the bottom. Then attach
the device to the rack by using 4 screws in the front panel tablet holes (screws are not
included). Connect all of the cables to the device and attach them to the rack with some tie
wraps.
The DIGI SCAN 1600 is compatible with a 19" enclosure. To install the device into a 19”
rack: Attach the device to the rack by using 4 screws in the front panel holes (screws are not
included). Connect all of the cables to the devices and attach them to the rack with some tie
wraps.
IMPORTANT:
• The openings in the rear and side panels are for cooling. Do not cover these openings.
• B e sure th at n o wei gh t is ad ded ont o the device in excess of 2 kg (4.4 lbs.).
• The maximum ambient operating temperature must not exceed 40°C (104°F).
• The rack and all mounted equipment in it must be reliably grounded to national and
local electrical codes.
PAGE 9
Chapter 1 : INTRODUCTION (continued) SCAN 1600 / DIGI SCAN 1600
1-7. DIGI SCAN 1600 FRONT PANEL DESCRIPTION
DIGI SCAN 1600
ANALOG WAY
R
MENU CONTROL
Allows to scroll thru the different menus.
ENTER: Validates a selected item.
A long push on this button allows to activate the STANDBY mode. A short push on this
push button allows to wake up the device.
EXIT MENU: Allows to exit from a LCD menu.
ADJUSTMENTS
POS. SIZE: Position or Size mode selection.
H: Horizontal image adjustment.
V: Vertical image adjustment.
ZOOM: Zoom mode selection (long push)
FREEZE: Freezes the displayed output (short push).
1-8. DIGI SCAN 1600 REAR PANEL DESCRIPTION
Ω
ON / OFF: AC power switch (O = OFF, I = ON).
POWER: Standard IEC connector (100-250 VAC, 0.5A, 50-60Hz automatic).
RS-232: RS-232 communication port on a DB9 female connector.
INPUT & MONITOR
COMPUTER INPUT: Analog computer input on HD15 female connector.
DVI-D INPUT: DVI-D computer input on DVI female connector.
RGB Hi-Z / 75 Ω: RGB input load. Set this button on Hi-Z if you connect a monitor on the MONITOR OUT
connector. If not set it on 75 Ω.
MONITOR OUTPUT: Analog computer output (loop-through) on HD15 female connector.
GENLOCK
IN: GENLOCK input.
OUT: GENLOCK output (loop-through).
VIDEO OUTPUTS
R, G, B, S: RGB/S or RGsB video outputs (on 3 or 4 BNC connectors).
Cr, Y, Cb: Component video (YUV) output (on 3 BNC connectors).
PAL/NTSC: Composite video output (on 1 BNC connector).
SDI: SD-SDI (4:2:2) output (on 1 BNC connector).
S.VIDEO: S.VIDEO output (4-pin mini DIN connector).
PAGE 10
SCAN 1600 / DIGI SCAN 1600 Chapter 1 : INTRODUCTION (continued)
1-9. SCAN 1600 FRONT PANEL DESCRIPTION
SCAN 1600
ANALOG WAY
R
MENU CONTROL
Allows to scroll thru the different menus (in Control mode).
ENTER: Validates a selected item.
A long push on this button allows to activate the STANDBY mode. A short push on this
push button allows to wake up the device.
EXIT MENU: Allows to exit from a LCD menu.
ADJUSTMENTS
POS. SIZE: Position or Size mode selection.
H: Horizontal image adjustment.
V: Vertical image adjustment.
ZOOM: Zoom mode selection (long push)
FREEZE: Freezes the displayed output (short push).
1-10. SCAN 1600 REAR PANEL DESCRIPTION
Ω
RS-232: RS-232 communication port on a DB9 female connector.
INPUT & MONITOR
COMPUTER INPUT: Analog computer input on HD15 female connector.
DVI-D INPUT: DVI-D computer input on DVI-I female connector.
RGB Hi-Z / 75 Ω: RGB input load. Set this button on Hi-Z if you connect a monitor on the MONITOR OUT
connector. If not set it on 75 Ω.
MONITOR OUTPUT: Analog computer output (loop-through) on HD15 female connector.
VIDEO OUTPUTS
R, G, B, S: RGB/S or RGsB video outputs (on 3 or 4 BNC connectors).
Cr, Y, Cb: Component video output (on 3 BNC connectors).
PAL/NTSC: Composite video output (1 BNC connector).
S.VIDEO: S.VIDEO output (4-pin mini DIN connector).
+5 Vdc: DC input connector.
PAGE 11
SCAN 1600 / DIGI SCAN 1600
Chapter 2 : STARTING
2-1. DIGI SCAN 1600 CONNECTIONS :
c Turn OFF all of your equipment before connecting.
d Connect the AC power supply cord to the DIGI SCAN 1600 and to an AC power outlet.
e Connect your computer source to the COMPUTER INPUT (HD15) connector or the DVI-D INPUT connector.
f As required, connect a control monitor on the MONITOR OUT (HD15) connector.
NOTE
: Set the RGB Hi-Z/75 Ω button on Hi-Z if you connect a monitor on the MONITOR OUT connector. If not set
it on 75 Ω.
NOTE:
g Connect your display devices (TV monitor, VCR...) to the outputs (analog or SDI).
h Turn ON the DIGI SCAN 1600 (rear panel switch). Then turn ON your input source and then your display devices.
• DIGI SCAN 1600 connection diagram:
The MONITOR OUT is available only if the COMPUTER source is analog.
6
Ω
2
• RGB/COMPONENT output connection:
4
3
5
5
PAGE 12
SCAN 1600 / DIGI SCAN 1600 Chapter 2 : STARTING (continued)
2-2. SCAN 1600 CONNECTIONS:
c Turn OFF all of your equipment before connecting.
d Connect your computer source to the COMPUTER INPUT (HD15) connector or the DVI-D INPUT connector.
e As required, connect a control monitor on the MONITOR OUT (HD15) connector.
: Set the RGB Hi-Z/75 Ω button on Hi-Z if you connect a monitor on the MONITOR OUT connector. If not
NOTE
set it on 75 Ω.
NOTE:
The MONITOR OUT is available only if the COMPUTER source is analog.
f Connect your display device (TV monitor, VCR…) to the outputs.
g Connect the external power supply to an AC power outlet and to the DC input connector of the SCAN 1600. Then
turn ON your input source and then your display devices.
• SCAN 1600 connection diagram:
• RGB/COMPONENT output connection:
2-3. SETTINGS
3
Ω
2
4
5
c We recommend resetting the device to all of its default values, with the front panel display menu (Control > default
value > yes) before proceeding.
d Select the Input source (ANALOG or DVI) with the front panel display menu (Input > Input select.).
e Select the Output standard with the front panel display menu (Output > Output std).
f Select the type of the RGB/YUV output with the front panel display menu (Output > RGB/YUV out).
2-4. IMAGE ADJUSTMENTS
c Select the UNDERSCAN mode with the front panel display menu (Image> under/over).
d Adjust the image position & size with the front panel buttons.
e Adjust the level of anti-flicker with the panel display menu (Image > flicker filter ).
f As required, make the others adjustments, available in the Image menu.
PAGE 13
SCAN 1600 / DIGI SCAN 1600
Chapter 3 : FRONT PANEL DISPLAY MENU DESCRIPTION
3-1. INTRODUCTION
The front panel display menu presents 2 modes: the STATUS MODE and the CONTROL MODE.
• The STATUS MODE indicates the input and output status of the device.
• The CONTROL MODE allows selecting and adjusting the parameters of the device.
3-2. CONTROL BUTTONS
The front panel display is controlled by 2 buttons and 1 knob:
knob: • In the CONTROL MODE, turn this knob to scroll thru the different menus.
ENTER button: • From the STATUS MODE, press this button to enter in the CONTROL MODE.
• From the CONTROL MODE, press this button to confirm a selected item.
EXIT / MENU button: • From the STATUS MODE, press this button to enter in the CONTROL MODE.
3-3. STATUS MODE
When switching ON, the front panel display shows the product's name and firmware versions as follows:
DEVICE MODEL DSV1600 DEVICE STATUS
• From the CONTROL MODE, press this button to:
- return to the previous menu without safeguarding the selection.
- return to the STATUS MODE (press several times).
DEVICE VERSION Version _._
Input : SVGA c INPUT STATUS
H = 37.9K V= 60 Hz d
Output : NTSC e OUTPUT STATUS
Internal 59.94 f
c INPUT FORMAT
d HORIZONTAL FREQUENCY (in kHz) / VERTICAL FREQUENCY (in Hz).
e OUTPUT STANDARD.
f OUTPUT RATE TYPE / OUTPUT FREQUENCY
PAGE 14
SCAN 1600 / DIGI SCAN 1600 Chapter 3 : FRONT PANEL DISPLAY MENU DESCRIPTION (continued)
3-4. CONTROL MODE
The menus of the device are configured as follow:
1 Input 1 Input status
2 Input select
3 SOG input
4 H. sync. load
5 Genlock load
6 Genlock H. ph.
7 Genlock Sc. ph.
2 Output 1 Output status
2 Output std.
(1)
(1)
Analog DVI
yes no
75 ohms Hi-Z
75 ohms Hi-Z
(1)
1 NTSC 59.94 Hz
2 PAL 50 Hz
3 NTSC J 59.94 Hz
3 Output rate
4 RGB/YUV out
5 Test pattern
3 Image 1 Flicker filter
2 Black level
3 RGB level
4 H smooth
5 Position status
6 Under/over
7 Zoom status
8 Preset
4 Control
1 Panel locking
2 Versions
3 Erase memories no yes
4 Default value no yes
(1)
Available on DSV1600 only.
(2)
Available for the analog source only.
(2)
(2)
(2)
1 internal
2 genlock
(1)
1 YUV
2 RGBS
3 RGsB
0 1 2 3 4 5 6 7
1 red level
2 green level
3 blue level
1 Underscan
2 Overscan
3 Zoom
PAGE 15
Chapter 3 : FRONT PANEL DISPLAY MENU DESCRIPTION (continued) SCAN 1600 / DIGI SCAN 1600
3-5. FUNCTIONS DESCRIPTION 1[INPUT] + ENTER.
1-1 [Input status] + ENTER.
Displays the input status.
1-2 [Input type] + ENTER.
Select one of the following input types with + ENTER:
• [analog]: Analog computer source connected to the HD15 input connector.
• [DVI] : Digital computer source connected to the DVI input connector.
1-3 [SOG input] + ENTER.
Select [Yes] if your input signal is in RGsB (SOG: Sync On Green), and valid with ENTER.
1-4 [H sync load] + ENTER.
Select the Horizontal sync load of your input signal with + ENTER.
1-5 [Genlock load] + ENTER. (Available on DSV1600 only).
Set on Hi-Z if the genlock out is used.
1-6 [Genlock H. ph.] + ENTER. (Available on DSV1600 only).
This function allows to adjust the genlock horizontal phase. Adjust with + ENTER.
1-7 [Genlock Sc. ph.] + ENTER. (Available on DSV1600 only).
This function allows to adjust the genlock Subcarrier phase. Adjust with + ENTER.
2[OUTPUT] + ENTER.
2-1 [Output status] + ENTER.
Displays the output status.
2-2 [Output std.] + ENTER.
Select one of the following standards with + ENTER:
• [NTSC] : NTSC standard for composite and S.VIDEO output and 60Hz frame rate for RGB/S and YUV
output.
• [PAL] : PAL standard for composite and S.VIDEO output and 50Hz frame rate for RGB/S and YUV
output.
• [NTSCj] : NTSC Japan standard for composite and S.VIDEO output and 60Hz frame rate for RGB/S and
YUV output.
2-3 [Output rate] + ENTER.
Select one of the following functions with + ENTER.
• [Internal] : The output standard depends of the selected output standard menu.
• [Genlock] : The output standard is synchronized onto the genlock input standard.
2-4 [RGB/YUV out] + ENTER.
Select the RGB/YUV wanted output with + ENTER.
• [YUV] : Component video output.
• [RGBS] : RGB/S video output.
• [RGsB] : RGB with Sync On Green video output.
2-5 [test pattern] + ENTER.
Select one item with + ENTER.
• [yes] = displays a test pattern onto the output.
• [no] = turns OFF the test pattern.
PAGE 16
SCAN 1600 / DIGI SCAN 1600 Chapter 3 : FRONT PANEL DISPLAY MENU DESCRIPTION (continued)
3-5. FUNCTIONS DESCRIPTION (continued)
3 [IMAGE] + ENTER.
3-1 [Flicker filter] + ENTER.
Select one of the 8 levels of the anti-flicker with and validate with ENTER.
3-2 [Black Level] + ENTER. (Available for analog input source only).
Adjust the Black level with + ENTER.
3-3 [RGB Levels] + ENTER. (Available for analog input source only).
Select an item with + ENTER.
• [Red] : Adjust the level of the Red with + ENTER.
• [Green] : Adjust the level of the Green with + ENTER.
• [Blue] : Adjust the level of the Blue with + ENTER.
3-4 [H. smooth] + ENTER. (Available for the analog input source only).
Select an item with + ENTER.
• [ON] : Active the horizontal filter.
• [OFF] : Inactive the horizontal filter.
3-5 [Position status] + ENTER.
Displays the image position status.
3-6 [Under/over] + ENTER.
Select an item with + ENTER.
• [underscan] : The output image is full screen.
• [overscan] : The output is 10% bigger than in underscan mode.
3-7 [Zoom status] + ENTER.
Displays the image zoom status.
3-8 [Preset] + ENTER.
This function allows to set all the image parameters (flicker filter, Black level, RGB level, under/overscan,
position & size) to the factory settings.
FUNCTION POSITION FUNCTION POSITION
3-1 Flicker Filter level 1. 3-4 H smooth off.
3-2 Black level. 0 3-6 under/over underscan.
3-3 RGB levels. 0 Position & size 0
4 [CONTROL] + ENTER.
4-1 [Panel locking] + ENTER.
This function allows to lock the front panel buttons. Select an item with + ENTER.
• [lock] : allows to lock the front panel push button.
• [unlock] : doesn't lock the front panel button.
NOTE:
To unlock push simultaneously on ENTER and EXIT.
4-2 [Version] + ENTER.
Status of the internal firmware.
4-3 [Erase memories] + ENTER.
This function allows to erase all the image settings memorized.
4-4 [Default value] + ENTER.
This function allows to clear the following adjustments and set them to the factory value:
FUNCTION POSITION FUNCTION POSITION
1-2 Input type analog 2-2 Output standard NTSC
1-3 SOG input no. 2-3 Output rate internal.
1-4 H sync load Hi-Z. 2-4 RGB/YUV out YUV
1-5 Genlock load Hi-Z. 2-5 test pattern no.
1-6 Genlock H Ph 0 4-1 panel locking unlock.
1-7 Genlock Sc. Ph. 0
PAGE 17
SCAN 1600 / DIGI SCAN 1600
Chapter 4 : UPDATING THE DEVICE
The device can be updated thanks a computer (PC) via its RS-232 communication port.
c Power OFF the device.
d Connect the RS232 connector of the device to the serial port of your computer with a DB9 M/F straight cable.
e Open the file: Scan 1600.exe (in Start > Program > ANALOGWAY > SCAN1600 updater).
f In the Port menu select the Com port connected to the device.
g Click on START on the software.
h Press and hold the ENTER front panel button, and simultaneously power ON the device. The update will start. Then
you can release the ENTER button.
i When the software displays: Program operation completed, click on the Quit button to close the update software.
Your device is now ready to work.
NOTE:
The updater files are available on our web site: www.analogway.com
PAGE 18
SCAN 1600 / DIGI SCAN 1600
Chapter 5 : REMOTE CONTROL SOFTWARE
Your device is shipped with a Windows compatible Remote Control Software . This software allows you to control and make
all adjustments by a simple mouse click.
NOTE:
The latest Remote Control Software is available on our web site: www.analogway.com
5-1. CONNECTIONS
-Connect the serial port of your control device to the RS-232 port (DB9 Female connector) of the device with a
straight
cable (DB9 Female / DB9 Male).
-Speed transmission: 9600 bauds, 8 data bits, 1 stop bit, no parity bit, no flow control.
-Pin-out:
PIN # FUNCTIONS
2 TRANSMIT DATA (Tx)
3 RECEIVE DATA (Rx)
5 GROUND (Gnd)
DB9 female (Rear panel of the device)
5-2. SOFTWARE INSTALLATION
c Turn your computer ON and wait for Windows to completely start.
d Insert the CD-ROM into your drive: the ANALOG WAY home window will open automatically.
e Select the language of the CD-ROM menus, then click on "Install a Remote Control Software" and select the name
of your device.
IMPORTANT: If the Autorun is not enabled: From the Windows desktop, open My Computer and select the CD-
ROM drive. Select the Autorun folder, and then select the autorun.exe file.
f Follow the Windows installation instructions.
5-3. COMMUNICATION SETUP
c Connect the RS-232 cable between the DSV1600/SSV1600 and the control device as indicated in the section
d Then only power ON all of the devices.
e Click on the program files SCAN1600 in Start>program>ANALOGWAY>SCAN1600 to run the software.
f Click on Controls menu and select Serial Port, and then select the COM port number corresponding to the
connection of the device.
5-1.
When the
communication
is established,
the message
"Device
connected" is
displayed.
PAGE 19
Chapter 5 : REMOTE CONTROL SOFTWARE (continued) SCAN 1600 / DIGI SCAN 1600
5-4. USING THE SOFTWARE
c Click on the Input tab and select the Computer input type.
d Click on the Output tab, and then select the needed adjustment (output standard, output rate...).
PAGE 20
SCAN 1600 / DIGI SCAN 1600 Chapter 5 : REMOTE CONTROL SOFTWARE (continued)
5-4. USING THE SOFTWARE (continued)
e Click on the Image tab and adjust your input.
f For the DSV1600 only, click on the Genlock tab and make the genlock adjustments.
PAGE 21
SCAN 1600 / DIGI SCAN 1600
Chapter 6 : TECHNICAL SPECIFICATIONS
6-1. COMPUTER INPUTS
• ANALOG COMPUTER INPUT
Connector: HD15 female.
Line frequency: From 29 kHz to 110 kHz.
Frame frequency: Up to 130 Hz.
Resolution: Up to 1600 x 1200.
Signal & Sync. type: RGBHV, RGB/S, RGsB (Sync On Green).
Level: R, G, B: 0.7 Vp/p.
H & V Sync: TTL.
Composite Sync: TTL and 0.3 V.
SOG (Sync On Green): 0.3 V.
Impedance: R, G, B: 75 Ohm
H: Hi-Z or 75 Ohm.
V: Hi-Z
• DIGITAL COMPUTER INPUT
Connector: DVI-I female.
Format: Digital Visual Interface (DVI)
Resolution: • 640 x 480 @ 60Hz (up to 120 Hz).
• 800 x 600 @ 60Hz (up to 120 Hz).
• 1024 x 768 @ 60Hz (up to 120 Hz).
• 1280 x 1024 @ 60Hz (up to 75 Hz).
• 1600 x 1200 @ 60Hz RB (Reduced Blanking).
6-2. VIDEO OUTPUTS
• RGB/S VIDEO
Connectors: 4 BNC female.
Frequency: 15.625 kHz / 50 Hz (625 lines).
15.734 kHz / 60 Hz (525 lines).
Level: R, G, B : 0.7 Vp/p.
Sync: 5 V TTL.
SOG: 0.3 Vp/p.
Impedance: 75 Ohm.
• COMPONENT
Connectors: 3 BNC female.
Frequency: 15.625 kHz / 50 Hz (625 lines).
15.734 kHz / 60 Hz (525 lines).
Level: Y: 1 Vp/p (0.7 V Luma + 0.3 V Sync.).
Cr, Cb: 0.7 Vp/p.
Impedance: 75 Ohm.
• S.VIDEO
Connector: 4-pin mini DIN female.
Standard: PAL : 15.625 kHz / 50 Hz - 625 lines.
NTSC : 15.734 kHz / 60 Hz - 525 lines - 7.5 IRE.
NTSC J : 15.734 kHz / 60 Hz - 525 lines - 0 IRE.
Level: Y : 1 Vp/p (0.7 V Luma + 0.3 V Sync.).
C : 0.7 Vp/p (0.3 V Chroma Burst).
Impedance: 75 Ohm.
PAGE 22
SCAN 1600 / DIGI SCAN 1600 Chapter 6 : TECHNICAL SPECIFICATIONS
6-2. VIDEO OUTPUTS (continued)
• COMPOSITE VIDEO
Connector: BNC female.
Standard: PAL : 15.625 kHz / 50 Hz - 625 lines.
NTSC : 15.734 kHz / 60 Hz - 525 lines - 7.5 IRE.
NTSC J : 15.734 kHz / 60 Hz - 525 lines - 0 IRE.
Level: 1 Vp/p (0.7 V Luma + 0.3 V Sync.).
Impedance: 75 Ohm.
• SDI (available on the DSV1600 only)
Connector: BNC female.
Signal: 270 Mbps serial digital output according to SMPTE 259M.
Impedance: 75 Ohm.
6-3. GENLOCK
Connectors: 2 BNC female.
Input signal type: Black Burst PAL or NTSC.
Impedance: 75 Ohm or Hi-Z.
Output: Passive loop-through.
6-4. REMOTE PORT
Connector: DB9 female.
Level: RS-232.
Data Rate: 9600 bauds, 8 bits data, 1 bit stop, no parity bit, no flow control.
6-5. ENVIRONMENTAL
Power Supply: DSV1600 : 100VAC-250VAC ; 50-60Hz ; I = 0.5A Max.
SSV1600 : External adapter (CE / UL / CSA / IEC950 approved)
Input (AC): 100-240 VAC, 1 A, 50-60 Hz.
Output (DC): 5 V, 4A, 20 W max.
Storage Temperature: - 25 °C to + 85 °C (- 13 °F to + 185 °F)
Operating temperature: 0 °C to + 50 °C (32 °F to 122 °F)
Hygrometry: 10% to 80% (without condensation)
Dimensions: Compatible with the 19" standard, height = 1 unit.
DSV1600: W 482 mm (19”) x D 265 mm (10.4”) x H 44 mm (1.74”).
SSV1600: W 221 mm (8.7”) x D 265 mm (10.4”) x H 43 mm (1.69”).
Weight: DSV1600: 3 kg (6.6 Lbs).
SSV1600: 1.2 kg (2.64 Lbs)
PAGE 23
SCAN 1600 / DIGI SCAN 1600
APPENDIX A: PROGRAMMER'S GUIDE
ANNEXE A: GUIDE DE PROGRAMMATION
A-1: INTRODUCTION
If you need to use your own Software Control program
from a PC or WORKSTATION with an RS-232 port,
the device allows communication through an ASCII
code protocol.
The device treats any character that it receives on the
RS-232 as a possible command but only accepts legal
commands. There is no starting/ending code needed in
a command string.
A command can be a single character typed on a
keyboard and does not require any special character
before or after it. (It is not necessary to press "ENTER"
on the keyboard). A command can be preceded by a
value (See chapter
A-2: COMMANDS STRUCTURE).
When the device receives a valid command, it will
execute the command. Then it will send back the status
of the parameters that have changed due to this
command.
If the command cannot be executed (value out of range,
no signal on the selected input), the device will just
sends back the current status of the corresponding
parameters.
If the command is invalid, an error response will be
returned to the control device. All responses returned to
the control device end with a carriage return <CR> and
a line feed <LF> signaling the end of the response
character string (see chapter
A-3: ERROR
RESPONSE).
A-2: COMMANDS STRUCTURE
A-1: INTRODUCTION
Si vous souhaitez utiliser votre propre logiciel de
contrôle avec votre PC, MAC ou Station de Travail par
un port RS-232, l'appareil peut communiquer par
simple émission / réception de caractères ASCII.
L'appareil traite tous les caractères reçus sur son port
RS-232 comme des commandes possibles; seules
certaines commandes sont reconnues et acceptées.
Une commande est constituée d'un ou deux caractères
sans code de contrôle ni avant, ni après. Il n'est pas
nécessaire d'appuyer sur "ENTER" du clavier. Une
commande peut être précédée d'une valeur (voir
chapitre
A-2: STRUCTURE D'UNE COMMANDE).
Lorsque l'appareil reçoit une commande valide, il
exécute cette commande puis renvoie à l'appareil de
contrôle l'état de tous les paramètres qui ont été
modifiés suite à l'envoie de cette commande.
Si la commande n’est pas reconnue (valeur en d ehors
de la plage, pas de signal sur l'entrée sélectionnée),
l'appareil renvoie uniquement les états des paramètres
correspondants.
Si la commande est invalide, une réponse d'erreur sera
retournée à l'appareil de contrôle. Toute réponse faite
à l’unité de contrôle se termine par un retour à la ligne
et par un saut de ligne (CR / LF) signalant la fin de la
commande de réponse. (Voir chapitre:
D'ERREUR)
.
A-2: STRUCTURE D'UNE COMMANDE
A-3: RÉPONSE
Commands are usually composed of a numerical value
followed by the command character. The characters
used without any numerical value return the current
setting of the command.
Command = Value (optional) + Character.
Examples / Exemples:
Command / Commande
Value/ Valeur Character / Caractère
none
aucune
F OFMT1
10 v VP10
A-3: ERROR RESPONSE
When the device receives from the control device an
invalid command or value, it returns an error response:
Example / Exemple:
Command / Commande
Value/ Valeur Character / Caractère
70260 z E10
Response
Réponse
Response
Réponse
Les commandes sont généralement constituées d'une
valeur numérique suivit par 1 ou 2 lettres de
commande. Une lettre utilisée sans valeur numérique
renvoie l'état de la commande.
Commande = Valeur (optionnelle) + Caractère
Description
Read the output format.
Lit le type de format.
Set the vertical position to 10.
Règle la position verticale à 10.
A-3: RÉPONSE D'ERREUR
Lorsque l'appareil reçoit de l'appareil de contrôle une
valeur ou une commande invalide, il retourne le
message d'erreur suivant:
Description
Invalid command. / Commande invalide.
PAGE 24
SCAN 1600 / DIGI SCAN 1600 APPENDIX A / ANNEXE A
A-4: COMMANDS AND RESPONSES TABLE A-4: TABLE DES COMMANDES ET RÉPONSES
COMMAND RESPONSE COMMAND DESCRIPTION VALUE /VALEUR
COMMANDE RÉPONSE DESCRIPTION DE LA COMMANDE
FRONT PANEL COMMANDS / COMMANDES DE LA FACE AVANT
z FRZ FREEZE. Rd/Wr 0 1 0 = freeze inactive 1 = freeze active.
a ASP Size mode selection. Rd/Wr 0 2 0 = underscan. 1 = overscan.
h HP Horizontal position adjustment. Rd/Wr 0 255
v VP Vertical position adjustment. Rd/Wr 0 255
w HW Horizontal size adjustment. Rd/Wr 0 255
s VS Vertical size adjustment. Rd/Wr 0 255
H ZHP Zoom horizontal position. Rd/Wr 0 255
V ZVP Zoom vertical position. Rd/Wr 0 255
W ZHW Zoom horizontal size. Rd/Wr 0 255 0 = 100% 255 =500%
S ZVS Zoom vertical size. Rd/Wr 0 255 0 = 100% 255 =500%
INPUT COMMANDS / COMMANDES D’ENTREE
D RGBI Input type Rd/Wr 0 1 0 = analog 1 = DVI
GP REFH Genlock H phase adjustment Rd/Wr 0 127 0 = -1.6 µs 127 = 1.57 µs
GS REFS Genlock subcarrier phase adjustment. Rd/Wr 0 255 0 = -180° 255 = 180°
GL GLD Genlock load. Rd/Wr 0 1 0 = Hi-Z 1 = 75 ohms.
E SOGI SOG input selection. Rd/Wr 0 1 0 = no 1 = yes.
l LOAD H sync load selection. Rd/Wr 0 1 0 = Hi-Z 1 = 75 ohms.
OUTPUT COMMANDS / COMMANDES DE SORTIE
F OFMT Output standard selection Rd/Wr 0 2 0 = NTSC
GR REFR Synchronization mode selection. Rd/Wr 0 1 0 = internal.
e OSIG RGB/YUV output selection. Rd/Wr 0 2 0 = YUV.
P OPAT Test pattern selection. Rd/Wr 0 1 0 = no test pattern.
IMAGE COMMANDS / COMMANDES DU MENU IMAGE
f FLK Flicker level selection. Rd/Wr 0 7
k BLK Black level adjustment Rd/Wr 0 127 0 = level -64 127 = level 63
r RLV Red level adjustment. Rd/Wr 0 255
g GLV Green level adjustment. Rd/Wr 0 255
b BLV Bleu level adjustment. Rd/Wr 0 255
L HSMT Horizontal smooth Rd/Wr 0 1 0 = OFF 1 = ON.
yp PRES PRESET Rd/Wr 0 1 1 = PRESET (automatic reset).
CONTROLS COMMANDS / COMMANDES DE CONTRÔLE
yl LOCK Front panel locking selection. Rd/Wr 0 1 0 = unlocks all buttons. 1 = locks all buttons.
yc EPOS Erase memory. Rd/Wr 0 1 1 = erase all memories (automatic reset).
Y FRES Default value. Rd/Wr 0 1 1 = set all the parameters to the default value
xu VERU Device version
xi I_ Identification number.
NOTE: Rd = Read only command / Commande de lecture. Rd/Wr = Read and write command / Commande de lecture et d'écriture.
TYPE
MIN MAX DESCRIPTION
2 = ZOOM.
1 = PAL
2 = NTSCj.
1 = genlock.
1 = RGBS.
2 = RGsB.
1 = test pattern selected.
(automatic reset).
Rd
Rd
0 65535 Example: 104 = Version 1.4
0 65535 Value displayed in hexadecimal in the device.
PAGE 25
APPENDIX A / ANNEXE A SCAN 1600 / DIGI SCAN 1600
COMMAND RESPONSE COMMAND DESCRIPTION VALUE /VALEUR
COMMANDE RÉPONSE DESCRIPTION DE LA COMMANDE
STATUS COMMANDS / COMMANDES D’ETAT
U UNIT Measures unity in kHz.
il ILD This command allows to calculate the
input line frequency in kHz
id IFD This command allows to calculate the
input frame frequency in Hz.
ik IST Input sync type detection
ip IPS Input sync detection.
ih IHP Sign of the horizontal input sync.
iv IVP Sign of the vertical input sync.
ii IIN Interlaced signal detection.
io IOO Status of the signal in comparison with
the input range frequency.
if IFA Input format detection
GA REFA Status of the synchronization mode
GF REFF Status of the synchronized format
(genlock).
GT REFT Frame frequency of the synchronized
signal (genlock) (in hundredth of Hz)
NOTE: Rd = Read only command / Commande de lecture. Rd/Wr = Read and write command / Commande de lecture et d'écriture.
TYPE
MIN MAX DESCRIPTION
Rd
Rd
0 65535
0 65535
Line frequency (in kHz) = (UNIT VALUE) ÷
(ILD VALUE).
Rd
0 65535 Frame frequency (in Hz) = (Line frequency in
Hz) ÷ (IFD VALUE).
Rd
0 3 0 = separate H & V
1 = Composite sync (TTL)
2 = SOG (Sync On Green)
3 = Composite sync (analog)
Rd
Rd
Rd
Rd
Rd
Rd
0 1 0 = no sync detected 1 = sync detected
0 1 0 = negative 1 = positive
0 1 0 = negative 1 = positive
0 1 0 = not interlaced 1 = interlaced
0 1 0 = in range 1 = out of range
0 8 0 = no signal
1 = "out of range" signal.
2 = VGA1 350l
3 = VGA2 400l
4 = VGA3 480l
5 = SVGA
6 = XGA
7 = SXGA
8 = UXGA
Rd
0 2 0 = internal
1 = genlock
2 = wrong signal.
Rd
0 2 0 = no signal
1 = NTSC 59.94 Hz.
2 = PAL 50 Hz.
Rd
0 65535
PAGE 26
SCAN 1600 / DIGI SCAN 1600 APPENDIX A / ANNEXE A
A-5: ASCII / HEX / DEC TABLE
A-5: TABLE ASCII / HEX / DEC
ASCII HEX DEC ASCII HEX DEC ASCII HEX DEC
space 20 32 @ 40 64 ` 60 96
! 21 33 A 41 65 a 61 97
" 22 34 B 42 66 b 62 98
# 23 35 C 43 67 c 63 99
$ 24 36 D 44 68 d 64 100
% 25 37 E 45 69 e 65 101
& 26 38 F 46 70 f 66 102
’ 27 39 G 47 71 g 67 103
( 28 40 H 48 72 h 68 104
) 29 41 I 49 73 i 69 105
* 2A 42 J 4A 74 j 6A 106
+ 2B 43 K 4B 75 k 6B 107
, 2C 44 L 4C 76 l 6C 108
- 2D 45 M 4D 77 m 6D 109
. 2E 46 N 4E 78 n 6E 110
/ 2 F 47 O 4F 79 o 6F 111
0 30 48 P 50 80 p 70 112
1 31 49 Q 51 81 q 71 113
2 32 50 R 52 82 r 72 114
3 33 51 S 53 83 s 73 115
4 34 52 T 54 84 t 74 116
5 35 53 U 55 85 u 75 117
6 36 54 V 56 86 v 76 118
7 37 55 W 57 87 w 77 119
8 38 56 X 58 88 x 78 120
9 39 57 Y 59 89 y 79 121
: 3A 58 Z 5A 90 z 7A 122
; 3B 59 [ 5B 91 { 7B 123
< 3C 60 \ 5C 92 | 7C 124
= 3D 61 ] 5D 93 } 7D 125
> 3E 62 ^ 5E 94 ~ 7E 126
? 3F 63 _ 5F 95 DEL 7F 127
PAGE 27
SCAN 1600 / DIGI SCAN 1600
WARRANTY
Analog Way warrants the product against any defects in materials and workmanship for a period of three years from the date of
purchase (back to the factory).
In the event of any malfunction during the warranty period, Analog Way will, at its discretion, repair or replace the defective
units, including free materials and labor.
This warranty does not apply if the product has been:
- improperly installed or abused,
- handled with improper care,
- used or stocked in abnormal conditions,
- modified, opened,
- damaged by fire, war, or Natural disasters (Acts of God).
In no way shall Analog Way be responsible for direct or indirect loss of profit or consequential damages resulting from any
defect in this product.
In case of any problem, get the serial number of the unit, a description of the problem, and then call your authorized dealer.
PAGE 28
Loading...